Related
I know this was really stupid cause I'm kicking myself right now,but I tried to flash CM7 and didn't flash the update before I rebooted my phone. Now my phone comes on and shows the vibrant screen as usual and goes to the cyanogen mod screen and then goes black after that. I can't get into recovery with the three button method and I have a mac. So I can't use Odin, even though I can get into download mode. Does anyone have any suggestions? I really don't want to try and go through the process of ordering a new phone, even though I do have insurance.
i did also need help.
Need help
I did also!!
I wanted to share my knowledge and experience from the past 2 days. Most of the help came from guides and posts on this forum so I wanted to give that back.
We were trying to root the SGS4G and because we're noobs we made the mistake of thinking it was a Vibrant. Got a Vibrant ROM and tried to flash it though Odin WITH re-partition checked. Everything we read said if you do either one of these things, you will brick your phone.
Sure enough we bricked the phone. It was trying to boot into the Vibrant ROM but was getting stuck on the word 'Vibrant' and then showing a whole lot of weird colored pixels. We then learned we'd made a massive mistake and that the phone wasn't a Vibrant after all.
We got a stock ROM for SGS4G and started trying to push them through Odin. Faced countless FAILS and freezes and finally it took us to the Recovery Mode and we tried the Restore option. It booted into a crippled SGS4G ROM. When it booted, it vibrated every 10 seconds or so and it had a null IMEI and unknown baseband.
We tried following a guide that wanted to change some text in the nv_data.bin but the numbers we were meant to be editing (0018810?) didn't exist in our nv_data.bin. So that didn't work for us.
In the meantime we tried to flash the stock ROM in Odin but kept getting FAILs and Freezes. With this step we lost even the crippled operating system and couldn't reach anything except the 'phone --!-- computer' screen. Luckily, this acts the same as download mode, so not bricked. We kept trying to push the stock SGS4G stock ROM (Froyo 2.2) several times and failing.
At one point we got a completely black screen, wouldn't turn on. Bricked again. We found this post on RootzWiki and it worked for us that time and brought it back from the black screen to download mode http://rootzwiki.com/topic/1820-how-to-unbrick-your-sgs4g/
Somehow we ended up at this guide here on XDA for fixing the "null/null" IMEI http://forum.xda-developers.com/showthread.php?t=1142829
We followed that guide. When you add the PIT file it automatically checks 'Re-Partition' in Odin, we didn't uncheck it. Bricked again. It was stuck on the Samsung logo and when we tried to get to download mode it got stuck on a black screen with the loading circle/lines and 2 computers were giving 'The USB device has malfunctioned' when we plugged it in. The unbrick guide above (RootzWiki) didn't help this time. We tried restarting the computer, let the phone rest without battery for half an hour, held power button for a minute without battery, still nothing.
Finally I accidentally pressed the power button (rather than the volume buttons to get into download mode) and it went to the samsung logo (as expected) and after that I was able to get into download mode. The key to this I think is to keep on trying powering on normally then try download mode over and over and eventually it should get unstuck and the computer should recognize it again.
Once I had it back in download mode, I followed this guide again BUT!!! I made sure to un-check re-partition and I did not check "Phone EFS Clear" (because I had tried that already before it was bricked and wanted to see if a straight ROM would work first). Everything worked perfectly, I got my IMEI and Baseband back, without modifying anything.
I don't know if this was a miracle, or if any of it will work for anyone else, but the moral of the story is don't give up even if you've done the absolute worst possible thing. I don't even think hardbrick exists on this phone after everything we were able to save it from.
Cheers
Hardbricks do exist on this phone but you have to try really hard to do it. A few people have managed it. Way to stick with it and recover your phone. I've done that more times than I can count.
hechoen said:
Hardbricks do exist on this phone but you have to try really hard to do it. A few people have managed it. Way to stick with it and recover your phone. I've done that more times than I can count.
Click to expand...
Click to collapse
I didn't feel like i really hard bricked it until i saw the USB computer connection error "device pluged in malfunctioned" in more than one PC.
Then i really felt like its a hardware BIOS chipset level problem now but man...
That story cracked me up. That is exactly why I spend days reading before I even root my phone. I made the mistake one time on my old G1 and it could not be revived.
Congrats on getting it working. (especially without flooding the q&a with redundant questions that have been described in detail several places )
hani1400 said:
I wanted to share my knowledge and experience from the past 2 days. Most of the help came from guides and posts on this forum so I wanted to give that back.
We were trying to root the SGS4G and because we're noobs we made the mistake of thinking it was a Vibrant. Got a Vibrant ROM and tried to flash it though Odin WITH re-partition checked. Everything we read said if you do either one of these things, you will brick your phone.
Sure enough we bricked the phone. It was trying to boot into the Vibrant ROM but was getting stuck on the word 'Vibrant' and then showing a whole lot of weird colored pixels. We then learned we'd made a massive mistake and that the phone wasn't a Vibrant after all.
We got a stock ROM for SGS4G and started trying to push them through Odin. Faced countless FAILS and freezes and finally it took us to the Recovery Mode and we tried the Restore option. It booted into a crippled SGS4G ROM. When it booted, it vibrated every 10 seconds or so and it had a null IMEI and unknown baseband.
We tried following a guide that wanted to change some text in the nv_data.bin but the numbers we were meant to be editing (0018810?) didn't exist in our nv_data.bin. So that didn't work for us.
In the meantime we tried to flash the stock ROM in Odin but kept getting FAILs and Freezes. With this step we lost even the crippled operating system and couldn't reach anything except the 'phone --!-- computer' screen. Luckily, this acts the same as download mode, so not bricked. We kept trying to push the stock SGS4G stock ROM (Froyo 2.2) several times and failing.
At one point we got a completely black screen, wouldn't turn on. Bricked again. We found this post on RootzWiki and it worked for us that time and brought it back from the black screen to download mode http://rootzwiki.com/topic/1820-how-to-unbrick-your-sgs4g/
Somehow we ended up at this guide here on XDA for fixing the "null/null" IMEI http://forum.xda-developers.com/showthread.php?t=1142829
We followed that guide. When you add the PIT file it automatically checks 'Re-Partition' in Odin, we didn't uncheck it. Bricked again. It was stuck on the Samsung logo and when we tried to get to download mode it got stuck on a black screen with the loading circle/lines and 2 computers were giving 'The USB device has malfunctioned' when we plugged it in. The unbrick guide above (RootzWiki) didn't help this time. We tried restarting the computer, let the phone rest without battery for half an hour, held power button for a minute without battery, still nothing.
Finally I accidentally pressed the power button (rather than the volume buttons to get into download mode) and it went to the samsung logo (as expected) and after that I was able to get into download mode. The key to this I think is to keep on trying powering on normally then try download mode over and over and eventually it should get unstuck and the computer should recognize it again.
Once I had it back in download mode, I followed this guide again BUT!!! I made sure to un-check re-partition and I did not check "Phone EFS Clear" (because I had tried that already before it was bricked and wanted to see if a straight ROM would work first). Everything worked perfectly, I got my IMEI and Baseband back, without modifying anything.
I don't know if this was a miracle, or if any of it will work for anyone else, but the moral of the story is don't give up even if you've done the absolute worst possible thing. I don't even think hardbrick exists on this phone after everything we were able to save it from.
Cheers
Click to expand...
Click to collapse
Wheooooooooowwww,..you just UNBRICKED mine, I know of the Battery pull etc...but the post you referenced
is MAGIC
This was not my first Rom nor Root on this phone, it weirdly happened while doing the GB starter....via ODIN, which i also used before..no clue what went wrong, oh well...
Thank you, thank you "i did"....Yohoooo
Yup i agree i like to read, reread then read as i do. This way i got a pretty good understanding of what I'm doing. Btw i have just started using one click and it is sooooo simple. I love it.
Sent from my SGH-T959V using XDA App
The link for fixing null/null IMEI is not working.
http://forum.xda-developers.com/showthread.php?t=1142829
diavel said:
The link for fixing null/null IMEI is not working.
http://forum.xda-developers.com/showthread.php?t=1142829
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=881162
Im still carrying this phone, stupid baseband unlock for iphone won't come out now I am carrying 2 phones, one as an ipod touch and the galaxy s! Good story, hope it can help others, but I am prepared to jump off of this bandwagon anytime now!
I recently picked up a Pantech Burst phone from At&t, and upgraded to ICS. I then proceeded to root the phone using the prestoroot.img method and it worked. Everything was running dandy until I got the VM Heap tool app and(stupidly) set the vm heap to 52m and attempted to reboot... It failed and all I got was a loop of boot up animations. I tried several times to reboot, and then tried to boot to recovery mode and factory reset. That worked, but it STILL didnt reboot..! I dont have a backup, and whenever i try to " Install update from external storage", it just fails over and over again. I found thestock firmware and downloaded it to my external sd card and install(still to no success). Im only 13 and cant afford a new phone! PLEASE SOMEONE HEEEELLLLPPPPPP!!!!!!!!!!!!!
Use P9070_Download_Tool_v3.3.zip and flash PRESTO_BIN_JUUS09032012_TP20_user using this method http://forum.xda-developers.com/showthread.php?p=28602800#post28602800. You might find other answers in that same thread Pantech Burst Essentials.
I love you!!!!!!!
dvinelord said:
use p9070_download_tool_v3.3.zip and flash presto_bin_juus09032012_tp20_user using this method http://forum.xda-developers.com/showthread.php?p=28602800#post28602800. You might find other answers in that same thread pantech burst essentials.
Click to expand...
Click to collapse
it workkeed!!!!!:d
DvineLord said:
Use P9070_Download_Tool_v3.3.zip and flash PRESTO_BIN_JUUS09032012_TP20_user using this method http://forum.xda-developers.com/showthread.php?p=28602800#post28602800. You might find other answers in that same thread Pantech Burst Essentials.
Click to expand...
Click to collapse
I bricked my phone few days back doing restore from CWM 6 downloeded online from ROM manager,
I wiped cache dalvik etc & rebooted, I could see the Tap the android screen then suddenly blank now it wont start
I get QHSUSB_dload in PC device manager any way out
I tried this method but I dont get the download button to click it remains greyed out.
Is there any driver for QHSUSB_dload?
Or do I have no hope at the moment or in near future?
just don`t use ROM manager for installing recovery . usually the result is bricked phone
Yah, i remember a fastboot brick i got from rom manager (LG Optimud ME)
Sent from a 2.8 inch screen
I also just bricked my Pantech Burst the same way...using ROM Manager. Is there a way to fix this or am I out of luck? I did try the method posted at the top of this thread. It just gets locked in the S/W Upgrading screen. Any help will be greatly appreciated.
I'm too in same situation.....i tried it updating via Pantech OS Upgrade tool......it updates successfully but doesnot bootup....
and now it shows some S/W Upgrading with red colour background
plz help me out:crying::crying::crying::crying::crying:
coolamjadkhan said:
I'm too in same situation.....i tried it updating via Pantech OS Upgrade tool......it updates successfully but doesnot bootup....
and now it shows some S/W Upgrading with red colour background
plz help me out:crying::crying::crying::crying::crying:
Click to expand...
Click to collapse
Mine did not upgrade successfully, but I have the exact same problem. On day three of waiting for a callback from Pantech on the issue. They are supposedly talking to the techs in Korea about it.
Maybe solved!
tajlund said:
Mine did not upgrade successfully, but I have the exact same problem. On day three of waiting for a callback from Pantech on the issue. They are supposedly talking to the techs in Korea about it.
Click to expand...
Click to collapse
Don't know if this is going to help, but I had the problem (as I described) red S/W Upgrading and couldn't do anything. Well, after about two weeks of sitting with the battery out, I decided to redownload and rerun the Pantech update app, and lo and behold, it fixed my phone. It also installed a more up to date version of Android 4.0, I went from 4.01 to 4.04.
This is after running the updater a good 30 or so times the past two weeks hoping for anything to work, now today, bam, it works fine.
I would recommend anyone in this situation give the most recent updater a try, it may solve your problem.
need help with my burst!!!!!
Hey! i have a pantech burst and i love it! but i had to reset it and now it wont work. my exhusband root it a few months ago....and he deleted the keyboard and the launcher..... so.... when i turn it on i cant do anything cause i cant write .... and if i skip the android start menu i cant see anything cause i dont have a launcher.... please someone help! what can i do?
:crying: Bricked my phone total unable start. any hardware diagnostic tool or manual reset button.
please help urgently
needhelppantech said:
Hey! i have a pantech burst and i love it! but i had to reset it and now it wont work. my exhusband root it a few months ago....and he deleted the keyboard and the launcher..... so.... when i turn it on i cant do anything cause i cant write .... and if i skip the android start menu i cant see anything cause i dont have a launcher.... please someone help! what can i do?
Click to expand...
Click to collapse
would you like to sell it cheaper rate???
Bricked Pantech Burst Stuck in S/W Downloading Mode and completely wiped ...
Ok I am having a similar issue guys. Last night I had to wipe my phone because it was overly full and I switched providers and the phone had become unusable. I tried using clockworkmod to do this and it wiped everything ( including clockworkmod. ) Now I only get a S/W Upgrading screen with a red box. I tried using the pantech download tool and the PANTECH_PRESTO_BIN_JUUS03122012.pdl file. It did appear that it was installing it but then it became stuck at the very very very end of things. I basically had to take the battery out to do anything at all as I had left the phone on all night to download the pdl file but without any luck.
When I reboot the phone it had the S/W Upgrading mode with the red screen. I've tried all of the different key combinations on the pantech burst etc volume up + volume down and power, volume down + power, volume up + power. None of these things will reboot the phone.
I am hoping I can use the pantech download tool to install a different pdl instead and possibly get it working that way. I know that when the phone is off if I plug it into usb then the screen lights up on it with the S/W Upgrading screen and the red box. If I press the power button or any other combinations of buttons + the power button it also does this. It literally will not do anything else.
I cannot use pantech pc suite because the phone originally was so unusable I could not put the android apk file on the phone even though I have it on my laptop.
I tried using adb and fastboot and it will not even find my device through ANY usb port on the laptop. I've tried deleting and reinstalling the drivers over and over. The only thing I know to do is reboot afterward and hopefully it will find my phone on usb with adb. If I can just get to a bootloader or flash functional firmware onto this phone I think I could get it working but I do not know enough about the pantech burst to try physically jumping anything on it in order to hard reset it.
So my only options right now look like maybe get a different pdl, possibly reboot and the drivers may find my phone, or JTAG this thing.
I can't put it in usb debugging mode because it won't boot. Since adb does not even find the device as being attached it seems as if this phone should be operating in a different port mode or something to make it visible. I could be wrong but I am hoping that rebooting fixes the driver issue and makes the phone visible.
I tried PDAnet also and once again it does not work because it cannot find the device. This could be a usb cable issue I suppose but I only have this particular cable I am pretty sure
I might try another cable as well...
Any other ideas ? Am I going to have to JTAG this thing or should it be fixable using the download tool and a different pdl ? Or do I need to find another way to completely wipe the phone first and THEN use the download tool with the pdl file ?
It does get a bit confusing with so many mods, roms, and methods to recover android phones. If I can get the phone to boot then I can reload my backups and all should be well. I do need this phone for business purposes also. Any ideas guys ?
PS> I am also pretty decent with linux distros like arch or ubuntu so I would like to also know if it would just be better to do this in linux and possibly use linux to manually switch the phone to a different device mode to make it visible in the instance of there being nothing wrong with the drivers.
Thanks for any ideas or suggestions ...
UPDATE - progress ???
dsull1981 said:
Ok I am having a similar issue guys. Last night I had to wipe my phone because it was overly full and I switched providers and the phone had become unusable. I tried using clockworkmod to do this and it wiped everything ( including clockworkmod. ) Now I only get a S/W Upgrading screen with a red box. I tried using the pantech download tool and the PANTECH_PRESTO_BIN_JUUS03122012.pdl file. It did appear that it was installing it but then it became stuck at the very very very end of things. I basically had to take the battery out to do anything at all as I had left the phone on all night to download the pdl file but without any luck.
When I reboot the phone it had the S/W Upgrading mode with the red screen. I've tried all of the different key combinations on the pantech burst etc volume up + volume down and power, volume down + power, volume up + power. None of these things will reboot the phone.
I am hoping I can use the pantech download tool to install a different pdl instead and possibly get it working that way. I know that when the phone is off if I plug it into usb then the screen lights up on it with the S/W Upgrading screen and the red box. If I press the power button or any other combinations of buttons + the power button it also does this. It literally will not do anything else.
I cannot use pantech pc suite because the phone originally was so unusable I could not put the android apk file on the phone even though I have it on my laptop.
I tried using adb and fastboot and it will not even find my device through ANY usb port on the laptop. I've tried deleting and reinstalling the drivers over and over. The only thing I know to do is reboot afterward and hopefully it will find my phone on usb with adb. If I can just get to a bootloader or flash functional firmware onto this phone I think I could get it working but I do not know enough about the pantech burst to try physically jumping anything on it in order to hard reset it.
So my only options right now look like maybe get a different pdl, possibly reboot and the drivers may find my phone, or JTAG this thing.
I can't put it in usb debugging mode because it won't boot. Since adb does not even find the device as being attached it seems as if this phone should be operating in a different port mode or something to make it visible. I could be wrong but I am hoping that rebooting fixes the driver issue and makes the phone visible.
I tried PDAnet also and once again it does not work because it cannot find the device. This could be a usb cable issue I suppose but I only have this particular cable I am pretty sure
I might try another cable as well...
Any other ideas ? Am I going to have to JTAG this thing or should it be fixable using the download tool and a different pdl ? Or do I need to find another way to completely wipe the phone first and THEN use the download tool with the pdl file ?
It does get a bit confusing with so many mods, roms, and methods to recover android phones. If I can get the phone to boot then I can reload my backups and all should be well. I do need this phone for business purposes also. Any ideas guys ?
PS> I am also pretty decent with linux distros like arch or ubuntu so I would like to also know if it would just be better to do this in linux and possibly use linux to manually switch the phone to a different device mode to make it visible in the instance of there being nothing wrong with the drivers.
Thanks for any ideas or suggestions ...
Click to expand...
Click to collapse
--------------------------------------------------------------------------
OK quick update, I found the pantech burst upgrade tool and the burst-hack.cmd script
I managed to successfully find my phone with the upgrade tool and it completely ran its course and I am guessing it installed Ice Cream Sandwich.
My new problem is that the phone goes to the pantech logo boot screen if I plug the phone into usb but that is all it will do. If I unplug the phone and try to get into S/W Upgrade mode again or power it on it will not do anything at all. Basically the display only comes on when plugged in at this point so I am wondering if the battery is even charged or if it will charge. I read somewhere ( in the gizmolord forum ) that a guy had the same issue as me and he ran this tool for his pantech burst and then left the battery out for 2 weeks and tried to power it back on and it worked for him.
Is it possible that I just need to power the device down completely and let it completely discharge before it will reboot or is this thing bricked ?
I am thinking that either the battery needs to charge, or the phone needs to discharge and power down completely, or the phone could be bricked. I have a feeling it is not bricked because the update tool said everything was successful and no errors or anything.
I will try leaving the battery out for awhile and letting the phone discharge on its own and see what kind of results I get. I would think that 16 - 24 hours would be sufficient. Any ideas ?
---------------------------------------------------------------------------------------------------------------------
Ok so I did a bit more digging and research and found out that the culprit is most likely the poorly designed charging circuit in the pantech phones. I found a tech blog called Mikes Techblog where he shows how to solve this on a pantech jest phone with the same issue. The problem is that the battery is 3.7v and is currently reading 2.8v on the volt meter. The phone will not even attempt to charge until 3.7v is available on the battery because of how the charge circuit is designed. I am going to try the usb cable trick and usb adapter and see if I can monitor its progress with the voltmeter and get it back up to 3.7 volts. After this it should allow me to charge it normally and should boot just fine. It is showing the pantech logo which tells me that the firmware is there and isn't buzzing or doing anything else weird so more than likely this is related to the battery and not having enough of a charge when running the official upgrade tool. This problem probably had already existed prior running the update tool and is why the S/W Upgrading screen only would come up AFTER being plugged into a power source and would disappear immediately. If the battery had any charge whatsoever and if the phone could see it then I would see a screen that tells me to plug my phone in and charge it. I am thinking this is solved but will only know after I charge the battery. From what I've been reading in comments from others the battery issue is prevalent on many different pantech phones including the burst model. Other people with the pantech burst have said in comments on Mike's blog that this made their phone boot right up and said that this was EXACTLY the issue. Perhaps the best way to use these pantech phones is to never ever let them fully discharge the battery.
Hi all..or anyone out there
I have had the seemingly strange bootloop problem on my stock note N8010...which stuck on the dreaded "samsung galaxy note 10.1" and only has odin feature working. (and no factory reset options because I think the poor old tab is crammed to bursting with apps, files and cache and so had a meltdown) poor thing.
so anyway I check these sites of techie wonder and wisdom and followed every logical option..starting with the simple ones
first ran power down and tried to boot up (x3) with no joy, then take apart the tablet to disconnect / reconnect the battery and boot up (x3) still no change.
So went and got the firmware from samwares (both jelly bean and kitkat) to then flash through odin....tried and failed first because of dodgy cable, but the then got a new one...and joy of joys (at first) odin recognised my tab and the firmware flashed across with pass..but then auto rebooted straight back into the dreaded samsung 10.1 again....so tried different versions of odins... and tried other global n8010 firmware...but funnily and frustratingly then all fully download and pass in odin (and the andoid logo and green download status bar on the tablet seems to shown that downloading is and has fully taken place.... but the darn thing still wont boot up past the samsung galaxy note 10.1
Sadly coming to the ends of my tether (of so many nearly there false hopes, high and lows) and very little cash to send it to the Sami tech bods doesnt help matter....I then read and tried the (supposed) last resort pit file/firmware option...first with kitkat (as apparently that worked for someone somewhere) and then tried with jelly bean..again each time itAlways passes in odin.... but auto reboots into the dreaded bootloop logo .... to haunt and torment me.. Aaaaagh!!!!.....I would not mind if it said action failed (for once) like some others seem to experiencet...but it always passes in ODIN????
So.....have come to the semi ignorant conclusion it is either the bootloader section of the tablet or the original software that is messed up or some internal hardware component has a fault.
but was wondering if there is anthing left to try...or would it potentially be possible or worth trying to root a tablet in this condition?
As although I have not ventured into the wild worlds of rooting.....I am now pretty confident of messing with this tablets mind..and have little to lose...so any further ideas and help would be great.
Exact same here. Never flashed, totally stock N8010. My wife hadn't used it for a couple of weeks. So she grabs it again and it was off. booted to nothing but the boot logo. Nothing worked except Download mode.
Flashing stock roms has Odin reporting success, but it still won't boot up. Trying re-Partition does give a fail as soon as I press start.
And we aren't alone. It appears there are quite a few of these cases. I have no idea how to solve this.
I have done a bit of rom flashing on my old galaxy S (the first one) and bootloaders and such usually were included in a ROM. Rooting was done with Recovery or an app and I think it was also possible with adb, IIRC (it's been a while).
It's my wife's Note and she's starting to scope out mini iPads...
Same problem with GT-N8010
I am also having the same problem.
I tried to upload a new ROM via ODIN. All was successful from the ODIN app (PASSED). but stuck on the boot screen. Power and Vol up does not work (it appears to but then crashes out to the boot screen again) so no way to do a hard factory reset.
Volume down/power does work and allows you to get to Odin mode. but as above, uploading a new ROM does not seem to work.
This is an un-rooted GT-N8010 with the stock ROM when I purchased it back in 2013 I believe.
Come on guys, give us some ideas.
Thanks
Gene
Sounds like wrong model firmware flashed as that's the usual bootloop problem .
Try Odin firmware flash wait to passed then remove battery for a short while and replace and try recovery mode .
In my case there is no incompatible firmware issue... The tablet just stopped working one morning and that was that.
Can't comment on the other posters though.
Sent from my GT-I9305 using XDA Free mobile app
Gene_uk said:
In my case there is no incompatible firmware issue... The tablet just stopped working one morning and that was that.
Can't comment on the other posters though.
Sent from my GT-I9305 using XDA Free mobile app
Click to expand...
Click to collapse
My wife's the same. Never done anything to it. No idea how to remove the battery. I let the battery run down once, then recharged it, made no difference.
That was before trying to flash the new firmware. My Note says N8010 on the back, it says so in the download mode. I got a firmware from SamMobile for the N8010. Don't know what else I can do.
Widdly said:
My wife's the same. Never done anything to it. No idea how to remove the battery. I let the battery run down once, then recharged it, made no difference.
That was before trying to flash the new firmware. My Note says N8010 on the back, it says so in the download mode. I got a firmware from SamMobile for the N8010. Don't know what else I can do.
Click to expand...
Click to collapse
Having same problem here ... tried flashing different firmwares along with PIT file - still no luck ..
stuck on samsung galaxy note screen .. cannot get recovery mode
Any help guys?
Hi everyone,
I'm hoping that someone can help me out with my device. I have a rooted sm-p900 that was working fine until a month ago when I tried to flash [ROM][7.1.x|SM-P900| Unofficial LineageOS 14.1 (v1awifi). I was busy multi-tasking and made the stupid mistake of flashing the rom before updating the BL. Since trying to do so, I have not been able to get past the first screen that says "Samsung sm-p900" . After the logo disappears, my screen remains lit but is just black.I could not restore my backup after either.
Where I am now:
- I can still access and use T.W.R.P. (latest 3.1.1) (If TWRP is left alone for too long, the device will reset to the same black screen and hang forever. If flashing a rom is taking long, the device will restart mid-flash as well.)
- I can still access download mode and use odin as well.
- I have since flashed the appropriate BL but that has not changed anything.
-I have tried clean flashing a magnitude of different roms and still come across the same problem.
I honestly have no idea how I can fix the device and have tried everything I know how. I would love to get it back as soon as possible. Any help is greatly appreciated, so thank you in advance!
jp2572 said:
Hi everyone,
I'm hoping that someone can help me out with my device. I have a rooted sm-p900 that was working fine until a month ago when I tried to flash [ROM][7.1.x|SM-P900| Unofficial LineageOS 14.1 (v1awifi). I was busy multi-tasking and made the stupid mistake of flashing the rom before updating the BL. Since trying to do so, I have not been able to get past the first screen that says "Samsung sm-p900" . After the logo disappears, my screen remains lit but is just black.I could not restore my backup after either.
Where I am now:
- I can still access and use T.W.R.P. (latest 3.1.1) (If TWRP is left alone for too long, the device will reset to the same black screen and hang forever. If flashing a rom is taking long, the device will restart mid-flash as well.)
- I can still access download mode and use odin as well.
- I have since flashed the appropriate BL but that has not changed anything.
-I have tried clean flashing a magnitude of different roms and still come across the same problem.
I honestly have no idea how I can fix the device and have tried everything I know how. I would love to get it back as soon as possible. Any help is greatly appreciated, so thank you in advance!
Click to expand...
Click to collapse
Have you tried taking it completely back to stock via Samsung Kies on your PC?
Sorry I don't have complete details, but it goes something like this (and if you search this site or Google, you'll find a good write-up on how to do a complete recovery using Kies):
1. If you can, make a backup using TWRP - if not, you are going to lose everything because of the next steps
2. Download and install the Kies software from the Samsung site and install it on your PC (I grabbed both versions, can install both on the same PC at the same time)
Make sure that it installs the Samsung USB driver
3. Connect to the tablet using the OEM cable - if you get a reaction from Kies, great
4. Somewhere in the Kies menu, you can tell it to do a complete recovery, including bootloader- if I remember correctly, you'll need your serial number (Sorry, been 18 months since I did just about the same thing and was able to recover it from my FUBAR, and I no longer run Windows so I can't step thru it)
It will go through downloading and flashing your tablet back to the state it was when you pulled it out of the box.
If you get to that point, you will have to go the whole route (including loading TWRP) to get it back to Lineage. It took me about two weeks to get it back to the way I had it before I was flashing and reading a book and talking to my wife all at the same time and didn't pay attention to what I touched on screen.
I apologize for the rambling and not having definitive statements, but I'm drugged up and been awake for the last 36 hours, and at my age that isn't a good combination.
Thank you so much for your help! I couldn't end up using that method because kies would not recognize my device for anything. It did get me inspired to try fixing it again however and it worked!
If anyone ever encounters the same or a similar problem, I just tried re-rooting it using odin and cf's autoroot file. It allowed me to be able to install roms again.
rhricik447 said:
Have you tried taking it completely back to stock via Samsung Kies on your PC?
Sorry I don't have complete details, but it goes something like this (and if you search this site or Google, you'll find a good write-up on how to do a complete recovery using Kies):
1. If you can, make a backup using TWRP - if not, you are going to lose everything because of the next steps
2. Download and install the Kies software from the Samsung site and install it on your PC (I grabbed both versions, can install both on the same PC at the same time)
Make sure that it installs the Samsung USB driver
3. Connect to the tablet using the OEM cable - if you get a reaction from Kies, great
4. Somewhere in the Kies menu, you can tell it to do a complete recovery, including bootloader- if I remember correctly, you'll need your serial number (Sorry, been 18 months since I did just about the same thing and was able to recover it from my FUBAR, and I no longer run Windows so I can't step thru it)
It will go through downloading and flashing your tablet back to the state it was when you pulled it out of the box.
If you get to that point, you will have to go the whole route (including loading TWRP) to get it back to Lineage. It took me about two weeks to get it back to the way I had it before I was flashing and reading a book and talking to my wife all at the same time and didn't pay attention to what I touched on screen.
I apologize for the rambling and not having definitive statements, but I'm drugged up and been awake for the last 36 hours, and at my age that isn't a good combination.
Click to expand...
Click to collapse
Try updating the bootloader again using odin
When this has happend factory reset
Flash the rom, addonsu and gapps in the same TWRP session
The rom should work then, I've been happily using it for about 6months now