Could anyone with a caliper make me a favor and measure the back glass width please (only glass, without the metal edge) ?
Related
Hello, I was wondering if any of you know if using a phantom skinz (or any other protection that doesn't absorb shocks) is enough to prevent free fall damage (at pocket height). Is the screen of a naked SGS resistant enough to not shatter after a few fall (unlike the iphone 4) ?
The SGS screen just like the iphone4 is made from glass think about that for a second
Now the sgs does have one advantage and that is that the glass doesn't extend all the way to the edge of the phone so you are less likely to crack it if it falls on it's edge.
My advice: get a rubber case.
Anyone knows if there is S6 clear cover for the Note 4?
The cases scratch the metal bezels and this gives protection and with the app Edge Notifications it has a tiny bump that lets the light show.
Thanks.
Has anyone found any screen protectors that fit properly? I've bought and tried two different ones (a tempered glass and a non-tempered glass) and neither of them stick to the sides of the screen. The left and right sides of the screen don't seem to allow the screen protectors to stick properly.
Weidas said:
No simple screen protector will fully cover since it has 2.5d glass edges.
You need something like this http://www.aliexpress.com/item/32741252826/32741252826.html
Click to expand...
Click to collapse
i bought that exact one. it's also too narrow on the sides and not full coverage like they advertise.
New user, so can't post a link, but search Amazon (they're prime too so you'll get them ASAP) for:
Le Pro 3 Screen protector, MicroP(TM) Full Screen 9H Hardness Ultra-thin Tempered Glass Front LCD Screen Protector for LeTV LeEco Le Pro 3 (Gold full coverage)
Just received and applied it to two Gold Le Pro 3's and they fit PERFECTLY edge to edge. They don't bulge or float off of the slightly curved edges and they look completely stock over the entire screen and top/bottom. Not entirely sure about the scratch protection or shock absorption quality yet but I'll check back in and update everyone in a while after these protectors get some use.
UPDATE: Sadly, after a few days use, I can confirm that the above protectors had the edge issues mentioned in another post. These problems are exacerbated by the case fitting so tightly that it actually "pushes" the screen protector and causes the (small amount) of sticky stuff on the sides of the screen protector to lose their grip. This allows a slight bubble of air on the sides of the phone which totally messes up touch. Back to Amazon and I'll just deal with a non-full coverage protector.
UPDATE #2: I attempted to install a 3rd party case on my wife's Pro 3 which had the "full size" protector and it ended up cracking the damn glass because the case forced a corner of the protector up at an angle. Anyone else who considers using these, please be aware of the issue (not sure why anyone would want to use them anyway due to the screen edge issues).
Hello
did anyone tried or can recommend a tempered glass protector for our phone that will cover all the screen, all the edges
I have tried many so far either transparent or else, but they always leave a certain margin on the side of the phone
I would like a screen glass that cover 100% of the screen please
any recommendation on eBay ?
I have a Nillkin 3D CP+ MAX. It covers the screen pretty well. But it has two issues:
- The transparent zone it's a bit (<0.5mm) smaller than phone's screen, and you notice that there's some part of the screen covered by the black sides.
- The biggest issue is that from 3 covers I tried on 3 different A8s, in two of them the proximity sensor is blocked. While applying the cover I activated the sensors test and It was impossible in the two cases to properly apply the cover without triggering the proximity sensor. I don't know what's wrong with them but that's my experience.
Does anyone have a link for a tempered glass protector for the 5g Ace that fits edge to edge without the camera hole?
All the items I find have reviews stating larger than necessary gaps around the edges, which I'm trying to avoid.
I believe the reason there is a gap around the edge of the screen is to accommodate a case. The edges of a case pushing up against the glass can cause it to bubble. When I was buying my screen protector, I had the exact opposite requirements than you for that very reason.