Database Info

[Q] No network service on CM10 flashed Xperia J

Hello guys,
Need help!
Flashed my Xperia J with CM10, FXP212.
Problem: I don't get network service.
Bluetooth and WiFi seem to work fine.
Thanks for any help
Edit: (If this helps in anyway) I dont see the FreeXP logo on startup, instead I get a green colored battery logo with the LED glowing red and then the CyanogenMod logo.
Edit 2:
I tried restoring the stock ROM from my backup.
The CWM recovery screen says restore complete. So I say" reboot now". It vibrates and then there is nothing on the screen except for the LED glowing red.
So I remove & re-insert the battery. Switch it on, but I can only enter recovery on purple LED glow. It always enters recovery.
So all I am able to do now is enter recovery and nowhere from there
What am I doing wrong?? Help guys!

Try to fastboot the kernel from the previous release.

your device the network locked
same problm with me :screwy:
---------------------------------
Sent from my GT-S5570L using Tapatalk 2

gavster26 said:
Try to fastboot the kernel from the previous release.
Click to expand...
Click to collapse
Hi,
Thanks for the reply.
I tried the boot.img kernel from FXP211 but no help.

saitri said:
your device the network locked
same problm with me :screwy:
---------------------------------
Sent from my GT-S5570L using Tapatalk 2
Click to expand...
Click to collapse
Hi saitri,
Thanks for the reply.
There was no network lock on the stock ROM.
Maybe I miss something here. What exactly is network lock?

JL.93 said:
Maybe I have the solution! Try this:
1) Flash stock rom ICS
2) Flash CM10's kernel with Flashtool
3) Various wipe
4) Flash CM10 with CWM
Fixed?
--- I'm sorry for my English, I translate with Google translator ---
Click to expand...
Click to collapse
Thanks for the reply.
I tried doing that earlier but landed into a bigger problem.
I can't boot in. It always enters recovery. Tried restoring the stock ROM from my backup but didnt work, It doesnt boot. So I press the 'Vol Up' key and it enters recovery.
What might have gone wrong here??

Myuvin said:
Hi saitri,
Thanks for the reply.
There was no network lock on the stock ROM.
Maybe I miss something here. What exactly is network lock?
Click to expand...
Click to collapse
I also do not understand, after I install cm10 210 and there was such a

saitri said:
I also do not understand, after I install cm10 210 and there was such a
Click to expand...
Click to collapse
Hi saitri,
U can flash a stock ROM, either ICS or JB using flashtool. Your phone will be unrooted. Bootloader remains unlocked.
You can then root it and install any other custom ROM. Though I havent installed a custom ROM yet after flashing the stock ROM.
Will let you know when I do it. Meanwhile you can flash a stock ROM. Let me knw if u need any assistance.
All those who replied: Thanks for your support and time.

[Q] Sony Xperia J IMEI Blank with sim no signal

I have a problem with my Sony Xperia J ST26i. It's rooted and unlocked.
Now I can start my mobile but he has no signal. Phone says there is no SIM card. If have my SIM card inserted. I have only wifi signal.
When I dial *#06# on my phone I see the display as shown in the attachment.
And with MTK Droid Tool I can't change/restore my IMEI. See also the screenshot of MTK. It says --- Unknown ROM structure, backup NOT possible!
Is there a another way to restore my IMEI? Also I have no .nv_data file. It's not on my phone. Have anyone this file for My phone or another solution?
Hardware : QCT
Model : ST26i
Build number : 11.2.A.0.31
Build date UTC : 20130419-050845
Android v : 4.1.2
Baseband v: -----
Kernel v : 3.4.0 ([email protected]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 Fri Feb 1 13:04:19 CST 2013
Uboot build v : -----
LCD Driver IC : -----

Sometimes, there are few bugs in stock fw. Like me, i cant turn on wifi. So either u restore using PCC or flash custom rom might help.
Sent from my Xperia Miro using xda premium

kreatonn said:
Sometimes, there are few bugs in stock fw. Like me, i cant turn on wifi. So either u restore using PCC or flash custom rom might help.
Sent from my Xperia Miro using xda premium
Click to expand...
Click to collapse
Thanks for the reply.
PCC restore is not an option. I haven't make one. So I go look on the internet for a custom ROM flash.

If wont work after you flash rom again... just relock and then unlock phone bootloader again!

2010matej said:
If wont work after you flash rom again... just relock and then unlock phone bootloader again!
Click to expand...
Click to collapse
My phone is working again! I went to a phone store in Scheveningen and they have put a rom on my phone back they do work. It's the original stock rom. It cost me €15 bud it's working again. In the future, I'll backup first and the go play with my phone.
Thanks for the support! :good:

Stoetel said:
My phone is working again! I went to a phone store in Scheveningen and they have put a rom on my phone back they do work. It's the original stock rom. It cost me €15 bud it's working again. In the future, I'll backup first and the go play with my phone.
Thanks for the support! :good:
Click to expand...
Click to collapse
15€ for this? OMG man! YOu can do that alone for free,just use flashtool !

Hi. I have a similar problem.
Phone (xperia J) is working fine with stock rom, rooted and unlocked bootloader. But when i flash custom rom there is no IMEI, no signal and no efs folder (nv_data file). And if I go back to stock rom the IMEI is back and mobile network works.
So my question is is there any way to transfer IMEI, recreate efs folder, so I can use custom roms?

I have to post 10 times before I can post links outside this forum.

Stoetel said:
I have to post 10 times before I can post links outside this forum.
Click to expand...
Click to collapse
And I have to wait five minutes.
Well just posting...

Stoetel said:
And I have to wait five minutes.
Well just posting...
Click to expand...
Click to collapse
Just keep calm. The solution is near.

Stoetel said:
Just keep calm. The solution is near.
Click to expand...
Click to collapse
Another post...

Stoetel said:
Another post...
Click to expand...
Click to collapse
Three to go...

Stoetel said:
Three to go...
Click to expand...
Click to collapse
Almost.
Scroll down ....

Stoetel said:
Almost.
Scroll down ....
Click to expand...
Click to collapse
After this post the solution!

mtommy88 said:
Hi. I have a similar problem.
Phone (xperia J) is working fine with stock rom, rooted and unlocked bootloader. But when i flash custom rom there is no IMEI, no signal and no efs folder (nv_data file). And if I go back to stock rom the IMEI is back and mobile network works.
So my question is is there any way to transfer IMEI, recreate efs folder, so I can use custom roms?
Click to expand...
Click to collapse
Use it at your own risk. Read this text first before you get started.
If you follow these steps your phone is back to the original settings. You have your signal back and you IMEI.
Now you want your phone rooted! Right? Right!
For rooting Sony Xperia J 11.0.A.7.5 version, 11.2.A.0.21, 11.2.A.0.31 (and or later) using ClockworkMod (CWM) recovery necessitating an unlocked bootloader (unlocked bootloader).
Broadly speaking, the rooting procedure using CWM recovery to install su, busybox and Superuser.apk files bundled in the update. The steps are: flash CWM, rooting package update using CWM recovery, then flash the stock kernel back.
Preparation:
1. Fastboot files here
2. Unlock Boatloader.
3. CWM Sony Xperia J (boot.img)
4. Sony Xperia J stock kernel 11.0.A.7.5 (kernel.sin), can be extracted from the image ftf.
5. Update file for rooting (root_xperia_signed.zip
Update March 8, 2013:
All the required files in the download is packaged in the following:
- Version 11.0.A.7.5
- Version 11.2.A.0.21
- Version 11.2.A.0.31 (May 30, 2013)
The steps:
1. Root_xperia_signed.zip copy files to the internal / external sdcard.
2. Prepare boot.img, kernel.sin, fastboot.exe into the working folder. (Make self a folder on you PC Harddisk)
3. Prepare boot.img, kernel.sin, fastboot.exe into the working folder.
Turn off the phone, unplug the USB cable and go into fastboot mode by pressing and holding down the Vol + Up while plugging in the USB cable, fastboot mode can be seen from the blue LED light on the top panel.
4. Check whether the connection is correct fastboot, type in Command Prompt:
fastboot getvar version​
If prompt <waiting for device> is displayed, then the connection is not successful, try to check whether the driver for fastboot already installed.
5. Flash CWM and restart the phone:
fastboot flash boot boot.img
fastboot reboot​
6. When the phone restarts, observe the LED on the bottom of the panel when it turns purple, immediately press and hold the Vol + Up button until the LED turns blue to get into CWM. USB cable can then be removed.
7. At CWM, select install zip from sdcard, then choose zip from sdcard / external sdcard and select the file in step 1 above. Continue reboot system now and turn off the phone (if necessary by removing the battery and repeat to enter fastboot mode).
8. Repeat steps 3 and 4.
9. Flash stock kernel:
fastboot flash boot kernel.sin
fastboot reboot​
10. Turn on the phone, check whether the application is installed SuperSU. Congratulations rooting successful.
Originaly posted 11th July by Hamzie Fickri
This text comes from this page.

Thanks, but that's not what i needed.
I already have stock rom rooted and working. Problem is if I install custom rom (FXP, PA), rom starts but no mobile signal and no IMEI. So I cannot use it.
Is there a way to like "copy/paste" IMEI from stock rom to custom rom?
edit: read somewhere on xda that this is a CM10 bug and CM10 based roms for xperia J.

disregard my last post (and previous post also)
fixed it!
what I did:
1. flash original stock ICS rom - 11.0.A.7.5.CE
2. reboot phone and then shutdown (not sure if this is necessary)
3. flash CWM img from http://forum.xda-developers.com/showthread.php?t=2034639
4. install custom rom (FXP233)
5. reboot
and now mobile signal works and IMEI is back.
hope it helps somebody and sorry for hijacking your thread Stoetel

mtommy88 said:
disregard my last post (and previous post also)
fixed it!
what I did:
1. flash original stock ICS rom - 11.0.A.7.5.CE
2. reboot phone and then shutdown (not sure if this is necessary)
3. flash CWM img from http://forum.xda-developers.com/showthread.php?t=2034639
4. install custom rom (FXP233)
5. reboot
and now mobile signal works and IMEI is back.
hope it helps somebody and sorry for hijacking your thread Stoetel
Click to expand...
Click to collapse
No problem!
The importent thing is, your mobile is working fine again! :good:
Thanks for the response.

Is there any solution about this problem on tipo?
Sent from my ST21i using xda app-developers app

tassosmer said:
Is there any solution about this problem on tipo?
Sent from my ST21i using xda app-developers app
Click to expand...
Click to collapse
Here you can find the latest Android 4.0.4 version for the Sony Xperia Tipo ST21
And here the CWM for Tipo.
Kernel can you extract from the ftf file. You can open th ftf file with Winzip or Winrar.
Flashtool. You can also use this program to check if your phone is bootlocked.
Go check this site if you need your phone to unlock the bootloader.
Follow the instructions above in the previous post. Or search on this forum for the solution.
Good luck.

Sony Xperia J-----OFF

Hello,
i 've tried to install CWM and sudently my phone turns off.
Since this time i had tried everything (i think!) to get it back to life , but without result!!
I press the power button-> SONY logo-> battery -> off!!
can anyone help me?

n1k1tasos said:
Hello,
i 've tried to install CWM and sudently my phone turns off.
Since this time i had tried everything (i think!) to get it back to life , but without result!!
I press the power button-> SONY logo-> battery -> off!!
can anyone help me?
Click to expand...
Click to collapse
Have you tried to install stock kernel and ROM?

answer
endlesik said:
Have you tried to install stock kernel and ROM?
Click to expand...
Click to collapse
yes but in flashmode i haven't success!!
can you give me instractions?

n1k1tasos said:
yes but in flashmode i haven't success!!
can you give me instractions?
Click to expand...
Click to collapse
Sure So you mean that you were not able to flash something in flashmode, right? You're flashing with Flashtool, or PCC?

ok
endlesik said:
Sure So you mean that you were not able to flash something in flashmode, right? You're flashing with Flashtool, or PCC?
Click to expand...
Click to collapse
pc combanion helps me out!!

n1k1tasos said:
pc combanion helps me out!!
Click to expand...
Click to collapse
So you solved the problem, right?

endlesik said:
Sure So you mean that you were not able to flash something in flashmode, right? You're flashing with Flashtool, or PCC?
Click to expand...
Click to collapse
:laugh::good: oh yes..
Sony maked it hard to root it..

The problem here isn't rooting the phone. Doomlord's tool works pretty well to root a stock .21 and .31 JB. The issue is CWM. Don't install it... There isn't yet a fully working version of CWM for our phone.

Actually there is but it is a matter of swapping kernels, what he meant was there is no permanent CWM for Xperia J but if you are not planning to flash ROMs download Flash Gordon App, Root Required

[ROM] [E SS/DS] Ultimate CM10 Install Guide!

Ultimate CM10 Install Guide​
Required:
-CM10 Zip (Odexed or Deodexed)
-Unlocked Bootloader
-Flashtool
-11.3.A.2.23 FTF (Single Sim Only)
11.3.A.2.1 FTF (Dual Sim Only)
-USB Cable
-Time
-Patience
-Zues Kernel V3.1
Lets Begin:[/SIZE]
1. Follow this guide to Unlock/Check if Your Bootloader Is Unlockable: http://unlockbootloader.sonymobile.com/
2. Install Flashtool.
3. Install Drivers which are in: C:\Flashtool\drivers\Flashtool-drivers.exe, run the program and install Flashmode and Fastboot Drivers.
4. Move the 11.3.A.2.23 FTF or the 11.3.A.2.1 FTF if your Xperia E is Dual Sim to C:\Flashtool\firmwares folder.
5. Run Flashtool, Click On the Lightning Bolt --> Select Flashmode and Select the 11.3.A.2.23 FTF or 11.3.A.2.1 if your phone is dual sim. and hit OK.
6. It will ask you to put the dervice in Flashmode, (PAY ATTENTION):
Power Down The Device,
Plug One end of the USB Cable into the USB Slot on the PC/Laptop,
Now Press the Volume Down Button and Plug the USB Cable In,
The computer an will recognise your phone and Flashtool (There will be a green led on your phone) will give an error resulting in it saying Install Drivers --> THIS IS OK!
Windows Will Now be installing drivers, let that finish then proceed.
7. Now Unplug the Cable, and do Step 6 and this time it will begin to Flash the FTF.
8. Once its done unplug your phone and this time plug it in while holding the Volume Up Button. (Blue Led)
9. Wait For Windows To Install Drivers then proceed.
10. Click the lightning bolt and this time select FastBoot Mode then select Select Kernel To Flash, in the right hand corner change .sin to .elf and go into the folder where you download Zues V3.1.elf and select it and it will Flash.
11. Once Finished Setup Your Phone Normally.
12. Copy the CM10 Zip to Your SD Card.
13. Power off your phone, power one while tapping the volume up or down button when you see the blue light.
14. Now use the Volume Buttons To Navigate To Wipe Data/Factory Reset and Hit Yes.
15. Now Select Install Zip From SD Card and Flash the CM10 Zip File.
16. Reboot and Enjoy Your CM10.
Download Links:
Flashtool: http://www.flashtool.net
Zues Kernel V3.1: http://forum.xda-developers.com/xperia-j-e/development/e-recovery-stock-11-3-2-23-t2658801
CM10 Zip (Odexed or Deodexed): http://forum.xda-developers.com/xperia-j-e/general/tip-fix-unknown-baseband-issueno-sim-t2674849
11.3.A.2.23 For Single Sim FTF: http://www.mediafire.com/download/3fmmkbmlqtjd6cy/Xperia+E+(C1505)_11.3.A.2.23_Unbranded.ftf
11.3.A.2.1 For Dual Sim FTF: http://www.4shared.com/file/55QLW02n/113A21.html

Cm10 work on Zeus kernel ?? Bugs ??

@UltraGamerHD Zeus on cm10?!?!?!?
XE rom page update coming soon for your guide,turbocs,ares,hades,posiden kernel

Grimlock007 said:
@UltraGamerHD Zeus on cm10?!?!?!?
XE rom page update coming soon for your guide,turbocs,ares kernel
Click to expand...
Click to collapse
This is for people who just got there boot loader unlocked and have no cwm.
Sent from my C1505 using XDA Premium 4 mobile app

Wow, if it works on zeus, then i dont have to flash different kernels when switching between cm10 and termin. But if i am already on 11.3.A.2.23 do i still need to flash it? Gonna try this when i get home
Sent from my C1505 using XDA Premium 4 mobile app

@UltraGamerHD Fixed Bugs ???Or is this Rom ??

DanielFlorin said:
@UltraGamerHD Fixed Bugs ???Or is this Rom ??
Click to expand...
Click to collapse
just an update to the old cm10.....
before: if you have gsm bug ,to fix you had to flash stock ftf again
now: flash rom again and voila! gsm is back
@UltraGamerHD mention stuff about that gsm bug and how to fix ,(in case it happens)
---------- Post added at 11:02 AM ---------- Previous post was at 10:56 AM ----------
UltraGamerHD said:
This is for people who just got there boot loader unlocked and have no cwm.
Sent from my C1505 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
aaaaah!
OK, mats had put hsr0 dual recovery boot.img in it.....
you should mention that...
people may try to flash Zues on cm10 afterwards....
@SmashMii no!....but once you flash cm10 rom, zeus gets overwritten....

DanielFlorin said:
@UltraGamerHD Fixed Bugs ???Or is this Rom ??
Click to expand...
Click to collapse
My dear fella. If you had read the thread I made you would know this!
This is the last time I will be saying this:
This is an update of jjm34 for the E dual. Version 1.1.0. Somehow on this version GSM isn't buggy. It is the E dual version, so you will have to select SIM1 as your SIM. The bugs are still the same:
-Video recording not working
-Video streaming not working
-Bluetooth not working(well, it turns on and connects but fails to exchange any media)
-Magnetometer not working(no automatic moving to landscape/portrait.
All right? Clear enough?
This ROM fixes just the GSM and nothing more. It was not made by me or UltraGamerHD. It is an update by jjm34.
Mats

What gets overwritten? I dont exactly understand, please explain to me. What i understand is i can flash cm10 on zeus, but when changing to termin, i have to reflash zeus?
Sent from my C1505 using XDA Premium 4 mobile app

MatsPunt said:
My dear fella. If you had read the thread I made you would know this!
This is the last time I will be saying this:
This is an update of jjm34 for the E dual. Version 1.1.0. Somehow on this version GSM isn't buggy. It is the E dual version, so you will have to select SIM1 as your SIM. The bugs are still the same:
-Video recording not working
-Video streaming not working
-Bluetooth not working(well, it turns on and connects but fails to exchange any media)
-Magnetometer not working(no automatic moving to landscape/portrait.
All right? Clear enough?
This ROM fixes just the GSM and nothing more. It was not made by me or UltraGamerHD. It is an update by jjm34.
Mats
Click to expand...
Click to collapse
and it has hsr0 dual recovery right?

Grimlock007 said:
and it has hsr0 dual recovery right?
Click to expand...
Click to collapse
Yep

SmashMii said:
What gets overwritten? I dont exactly understand, please explain to me. What i understand is i can flash cm10 on zeus, but when changing to termin, i have to reflash zeus?
Sent from my C1505 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
once you flash cm10 zeus kernel gets overwritten with hsr0 dual recovery 1.3ghz oc kernel(made specially for cm10) .....which may cause gsm crash on termin/stock rom

UltraGamerHD said:
Required:
-Zues Kernel V3.1
Lets Begin:[/SIZE]
Click to expand...
Click to collapse
1. Zeus is spelled wrong.
2. [SIZE] tag is missing
And thanks for the guide!

Before this, i have problem on CM10, Xperia E Dual.
Cannot charge phone, no LED charging.
After flash stock ROM, there is no problem.
So i try this ROM, luckly, there is no problem.
Thanks for a guide!
Keep it up! Hope have 4.2.2 on Xperia E Dual same like this ROM :good:
P/s : sorry my spelling bad :crying:

meiax93 said:
Before this, i have problem on CM10, Xperia E Dual.
Cannot charge phone, no LED charging.
After flash stock ROM, there is no problem.
So i try this ROM, luckly, there is no problem.
Thanks for a guide!
Keep it up! Hope have 4.2.2 on Xperia E Dual same like this ROM :good:
P/s : sorry my spelling bad :crying:
Click to expand...
Click to collapse
no more updates for E.... cm11 under development

cm10 help needed
UltraGamerHD said:
Ultimate CM10 Install Guide​
Required:
-CM10 Zip (Odexed or Deodexed)
-Unlocked Bootloader
-Flashtool
-11.3.A.2.23 FTF (Single Sim Only)
11.3.A.2.1 FTF (Dual Sim Only)
-USB Cable
-Time
-Patience
-Zues Kernel V3.1
Lets Begin:[/SIZE]
1. Follow this guide to Unlock/Check if Your Bootloader Is Unlockable: http://unlockbootloader.sonymobile.com/
2. Install Flashtool.
3. Install Drivers which are in: C:\Flashtool\drivers\Flashtool-drivers.exe, run the program and install Flashmode and Fastboot Drivers.
4. Move the 11.3.A.2.23 FTF or the 11.3.A.2.1 FTF is your Xperia E is Dual Sim to C:\Flashtool\firmwares folder.
5. Run Flashtool, Click On the Lightning Bolt --> Select Flashmode and Select the 11.3.A.2.23 FTF or 11.3.A.2.1 if your phone is dual sim. and hit OK.
6. It will ask you to put the dervice in Flashmode, (PAY ATTENTION):
Power Down The Device,
Plug One end of the USB Cable into the USB Slot on the PC/Laptop,
Now Press the Volume Down Button and Plug the USB Cable In,
The computer an will recognise your phone and Flashtool (There will be a green led on your phone) will give an error resulting in it saying Install Drivers --> THIS IS OK!
Windows Will Now be installing drivers, let that finish then proceed.
7. Now Unplug the Cable, and do Step 6 and this time it will begin to Flash the FTF.
8. Once its done unplug your phone and this time plug it in while holding the Volume Up Button. (Blue Led)
9. Wait For Windows To Install Drivers then proceed.
10. Click the lightning bolt and this time select FastBoot Mode then select Select Kernel To Flash, in the right hand corner change .sin to .elf and go into the folder where you download Zues V3.1.elf and select it and it will Flash.
11. Once Finished Setup Your Phone Normally.
12. Copy the CM10 Zip to Your SD Card.
13. Power off your phone, power one while tapping the volume up or down button when you see the blue light.
14. Now use the Volume Buttons To Navigate To Wipe Data/Factory Reset and Hit Yes.
15. Now Select Install Zip From SD Card and Flash the CM10 Zip File.
16. Reboot and Enjoy Your CM10.
Download Links:
Flashtool: http://www.flashtool.net
Zues Kernel V3.1: http://forum.xda-developers.com/xperia-j-e/development/e-recovery-stock-11-3-2-23-t2658801
CM10 Zip (Odexed or Deodexed): http://forum.xda-developers.com/xperia-j-e/general/tip-fix-unknown-baseband-issueno-sim-t2674849
11.3.A.2.23 For Single Sim FTF: http://www.mediafire.com/download/3fmmkbmlqtjd6cy/Xperia+E+(C1505)_11.3.A.2.23_Unbranded.ftf
11.3.A.2.1 For Dual Sim FTF: http://www.4shared.com/file/55QLW02n/113A21.html
Click to expand...
Click to collapse
i want to go back to stock rom...how to do .. i have c1505 stock rom should i flash by flash tool
---------- Post added at 02:56 AM ---------- Previous post was at 02:54 AM ----------
meiax93 said:
Before this, i have problem on CM10, Xperia E Dual.
Cannot charge phone, no LED charging.
After flash stock ROM, there is no problem.
So i try this ROM, luckly, there is no problem.
Thanks for a guide!
Keep it up! Hope have 4.2.2 on Xperia E Dual same like this ROM :good:
P/s : sorry my spelling bad :crying:
Click to expand...
Click to collapse
i have same prob now bro how did u flash .. i mean u directly flash ur rom with flashtool ???? i have stock rom if i do will my phone will back to normal ???

Rajat22 said:
i want to go back to stock rom...how to do .. i have c1505 stock rom should i flash by flash tool
---------- Post added at 02:56 AM ---------- Previous post was at 02:54 AM ----------
i have same prob now bro how did u flash .. i mean u directly flash ur rom with flashtool ???? i have stock rom if i do will my phone will back to normal ???
Click to expand...
Click to collapse
Flash the FTF file from flashtool.
In flashtool, click the thunder icon, select flashmode, choose the FTF file, and select flash.
Now Wait.
Flashtool will prompt u to connect device in flashmode. Shut down your device, hold the down volume key and connect to pc.
You're done.
Next time, please don't quote op
Sent from my C1605 using XDA Premium 4 mobile app

cm10 help needed
sohailferdous said:
Flash the FTF file from flashtool.
In flashtool, click the thunder icon, select flashmode, choose the FTF file, and select flash.
Now Wait.
Flashtool will prompt u to connect device in flashmode. Shut down your device, hold the down volume key and connect to pc.
You're done.
Next time, please don't quote op
Sent from my C1605 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
last question ... will it back my phone to normal ??? and what about my recovry will it delet ??? if it delet will i have to flash my kernel to cwm ?? now i have twrp

Rajat22 said:
last question ... will it back my phone to normal ??? and what about my recovry will it delet ??? if it delet will i have to flash my kernel to cwm ?? now i have twrp
Click to expand...
Click to collapse
If you flash the FTF (firmware) file, you're phone will become absolutely normal. Like a factory release. It shall become ordinary, like the very first time when you bought it.
No, the recoveries wont last, you will have to flash the kernels again.
Sent from my C1605 using XDA Premium 4 mobile app

cyanogen
sohailferdous said:
If you flash the FTF (firmware) file, you're phone will become absolutely normal. Like a factory release. It shall become ordinary, like the very first time when you bought it.
No, the recoveries wont last, you will have to flash the kernels again.
Sent from my C1605 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
thank you so much.. i will leave this cm10 its worest.. no sim detec.. no battery charge... i will flash it with stock rom

Xperia L doesn't work

My xperial L c2105 phone doesn't power on. When I press the power button the phone vibrate, but there are not any word in the screen.
When I connect the charger it doesn't charge.
But fastboot mode and flashmode work correctly.
Sometimes the red indicate light shows continuesly

Priyamal said:
My xperial L c2105 phone doesn't power on. When I press the power button the phone vibrate, but there are not any word in the screen.
When I connect the charger it doesn't charge.
But fastboot mode and flashmode work correctly.
Sometimes the red indicate light shows continuesly
Click to expand...
Click to collapse
Before I start to offer ideas on the issue do you have any idea what caused this to start?
Did you flash a custom ROM/Recovery/Firmware to the phone or did it just stop working ?

TechMinerUK said:
Before I start to offer ideas on the issue do you have any idea what caused this to start?
Did you flash a custom ROM/Recovery/Firmware to the phone or did it just stop working ?
Click to expand...
Click to collapse
Yes. I try to unlock bootloader by official way. But i couldnt unlock it on that way. So I unlocked it using flash tool.
Then i install cwm recovery. But after that i couldnt turn on my phone. I think i did some mistake.

Priyamal said:
Yes. I try to unlock bootloader by official way. But i couldnt unlock it on that way. So I unlocked it using flash tool.
Then i install cwm recovery. But after that i couldnt turn on my phone. I think i did some mistake.
Click to expand...
Click to collapse
Then the best option is to download the flashing tool for your device and flash the stock firmware to it using fastboot. That should get it into a working state which you can then work from to install a custom recovery.

TechMinerUK said:
Then the best option is to download the flashing tool for your device and flash the stock firmware to it using fastboot. That should get it into a working state which you can then work from to install a custom recovery.
Click to expand...
Click to collapse
I flash a stock fermware. Now start the phone and get bootloop. Please help me to solove this.
My phone is sony xperia L c2105
Build number : 15.3.a.1.17

Priyamal said:
I flash a stock fermware. Now start the phone and get bootloop. Please help me to solove this.
My phone is sony xperia L c2105
Build number : 15.3.a.1.17
Click to expand...
Click to collapse
Before booting/after flashing the firmware make sure you reset the device in recovery so it has a "clean slate" to boot to as this should remove any old apps/settings from the previous firmware/ROM that could cause it to bootloop

TechMinerUK said:
Then the best option is to download the flashing tool for your device and flash the stock firmware to it using fastboot. That should get it into a working state which you can then work from to install a custom recovery.
Click to expand...
Click to collapse
TechMinerUK said:
Before booting/after flashing the firmware make sure you reset the device in recovery so it has a "clean slate" to boot to as this should remove any old apps/settings from the previous firmware/ROM that could cause it to bootloop
Click to expand...
Click to collapse
Thank you for help. Now my phone work well. Thank you again.

Priyamal said:
Thank you for help. Now my phone work well. Thank you again.
Click to expand...
Click to collapse
I don't suppose you could use the thanks button ?