Hey all,
I have got a Note 10.1 GT-N8013 16gb WiFi that appears to be soft bricked. I rooted it, no custom rom, a couple years ago. The other day i pulled it outta my bag to find it frozen on the black Samsung Galaxy Note 10.1 screen. I tried rebooting it and it never would boot any further. I have tried the suggestions of re flashing stock firmware and have not had any luck. I even tried flashing stock firmware with a pit file. I cannot access Clock Work recovery. It crashes as soon as the writing appears on the bottom left of the screen. I do not know what to do now. Any suggestions?
Thanks
Chip
Are you able to boot into download mode ?
bikrame said:
Are you able to boot into download mode ?
Click to expand...
Click to collapse
Yes I am
Flash stock rom via odin and post where it fails in Odin .
Flashing a PIT file may have been the wrong choice .
JJEgan said:
Flash stock rom via odin and post where it fails in Odin .
Flashing a PIT file may have been the wrong choice .
Click to expand...
Click to collapse
It doesnt fail in odin, thats the thing. Its successful but still wont boot past samsung screen. I only tried the pit file after the 100th try
Related
N8013 - Boots up only to Galaxy Note logo
with VOLUME DOWN + POWER button I can get to the ODIN MODE
can connect with ODIN on my PC ... but do not know
what is the next step to get Note 10.1 to work
PLEASE HELP
thx
Next step is to download the latest and greatest for the n8013, and flash it. Depending on the version of Odin you have, it might be the PDA button you use to load the stock ROM with.
You can find the stock image you need on sites like this http://samsung-updates.com/device/?id=GT-N8013 but search around, because there are much faster places to download from out there.
Downloaded, Flashed ....
1st try: KIES_HOME_N8013UEUCMI3_N8013XARCMI3_813049_REV00_user_low_ship.tar.md5
ODIN says PAS but after reboot, stopped on Galaxy Note logo
2nd try: N8013RootInjectedSystem.tar
ODIN says PAS but after reboot, stopped on Galaxy Note logo
I see what your issue is then. They both worked, just boot into recovery and do a factory wipe, then it should boot up fine.
unforunately there is no Factory Reset option
only ODIN MODE
attilato said:
unforunately there is no Factory Reset option
only ODIN MODE
Click to expand...
Click to collapse
Try finding a .pit file for the n8013 and flash that along with the stock ROM in Odin.
Can NOT find any .PIT file........
electrikjesus said:
Try finding a .pit file for the n8013 and flash that along with the stock ROM in Odin.
Click to expand...
Click to collapse
attilato said:
Can NOT find any .PIT file........
Click to expand...
Click to collapse
Just took a little google searching https://www.dropbox.com/s/hl0furhcm832aru/My-N8013.pit
Help softbricked device
well i was running more rom on the device when i droped it then i got the screen and digi replaced
and when the tech tuned it on for the first time after repair we got a udc start screen that says unknown error at the top
i can get to download mode though. but even after trying to restore the bootloader or flash a new modem i cant get to any recovery.
right now this is what it says in download mode.
odin mode
product name : SM-G900P
current binary: custom
system status : custom
knox warranty void 0x1 (4)
i can go to download mode or try and let it boot up to the samsung boot but it says recovery booting in blue and loops there on reboot.
i forget the name of the modem i was on in more rom. i think it was the one be4 ota6
but i want to update to latest version of modem and rom not sure where to start.
i cant seem to get back to stock or custom recovery at all. or even boot up to a rom now. and i honestly have no idea why? =( can someone help?
jackrabbit72380 said:
Help softbricked device
well i was running more rom on the device when i droped it then i got the screen and digi replaced
and when the tech tuned it on for the first time after repair we got a udc start screen that says unknown error at the top
i can get to download mode though. but even after trying to restore the bootloader or flash a new modem i cant get to any recovery.
right now this is what it says in download mode.
odin mode
product name : SM-G900P
current binary: custom
system status : custom
knox warranty void 0x1 (4)
i can go to download mode or try and let it boot up to the samsung boot but it says recovery booting in blue and loops there on reboot.
i forget the name of the modem i was on in more rom. i think it was the one be4 ota6
but i want to update to latest version of modem and rom not sure where to start.
i cant seem to get back to stock or custom recovery at all. or even boot up to a rom now. and i honestly have no idea why? =( can someone help?
Click to expand...
Click to collapse
Follow the instructions from this post. Since you are soft bricked at the moment, you'll need to start at step 4. If you have an extSD in your phone, you might want to pull it until after you're up and running because the "Android" folder from Kitkat needs to be deleted and rebuilt for Lollipop.
That's what I tryed first but it didn't work,
First step.... flash SM-G900P_OA6_FullRestore.
(on boot i have samsung galaxy s5 screen with blue letters at the top saying recovery booting and it loops.)
sense that didn't work i tryed... SM-G900P_NI3-Full_Restore_Unrooted (Compressed Archive)
(on boot i have samsung galaxy s5 screen with blue letters at the top saying recovery booting and it loops.)
then i tryed SM-G900P_OA6_FullRestore. again but still no luck im out of ideas
I cant get to any recovery.
please help.
jackrabbit72380 said:
That's what I tryed first but it didn't work,
First step.... flash SM-G900P_OA6_FullRestore.
(on boot i have samsung galaxy s5 screen with blue letters at the top saying recovery booting and it loops.)
sense that didn't work i tryed... SM-G900P_NI3-Full_Restore_Unrooted (Compressed Archive)
(on boot i have samsung galaxy s5 screen with blue letters at the top saying recovery booting and it loops.)
then i tryed SM-G900P_OA6_FullRestore. again but still no luck im out of ideas
I cant get to any recovery.
please help.
Click to expand...
Click to collapse
Are you using the wrong terminology? You have to use Odin and a PC to install the .tar. Also, the first boot into Lollipop can take about 20 minutes. You have to be patient. I see you posting in different threads and you seem to be digging deeper into a hole.
Are you using Odin and starting by downloading (to PC) the file in step #4? Then follow the remaining steps "exactly". Re-read those instructions and if you not already downloaded the needed files, do that first.
Ramer said:
Are you using the wrong terminology? You have to use Odin and a PC to install the .tar. Also, the first boot into Lollipop can take about 20 minutes. You have to be patient. I see you posting in different threads and you seem to be digging deeper into a hole.
Are you using Odin and starting by downloading (to PC) the file in step #4? Then follow the remaining steps "exactly". Re-read those instructions and if you not already downloaded the needed files, do that first.
Click to expand...
Click to collapse
Yes I downloaded the files to the pc.
Im using odin3.07
in pda I add the file Odin'd the [ODIN][TAR][5.0] SM-G900P OA6 (Official!) - Full Restore (ROM, Modem, Kernel),
put phone in download mode.
flash file!
ODIN SAYS PASS
next phone reboots to samsung galaxy black screen with with blue letters at the top saying
RECOVERY BOOTING......
then boot loops there.
I CANT GET TO STEP 5
I am not able to boot to the rom or recovery
jackrabbit72380 said:
Yes I downloaded the files to the pc.
Im using odin3.07
in pda I add the file Odin'd the [ODIN][TAR][5.0] SM-G900P OA6 (Official!) - Full Restore (ROM, Modem, Kernel),
put phone in download mode.
flash file!
ODIN SAYS PASS
next phone reboots to samsung galaxy black screen with with blue letters at the top saying
RECOVERY BOOTING......
then boot loops there.
I CANT GET TO STEP 5
I am not able to boot to the rom or recovery
Click to expand...
Click to collapse
Try this: Do a battery pull, then put the phone in Download mode, hook up to PC and then open Odin and then Odin custom recovery, either twrp or Philz. Uncheck auto reboot in odin and once it passes, pull the battery, unplug and boot into recovery. Also, you might update Odin, there's a link to Odin 3.10.0 in my post. Let's see if we can get that far and go from there.
ramer said:
try this: Do a battery pull, then put the phone in download mode, hook up to pc and then open odin and odin custom recovery, either twrp or philz. Uncheck auto reboot in odin and once it passes, pull the battery, unplug and boot into recovery. Also, you might update odin, there's a link to odin 3.10.0 in my post. Let's see if we can get that far and go from there.
Click to expand...
Click to collapse
ok used odin 10
tryied everything you said exactly phone reboots on samsung galaxy s5 boot logo everytime. Whether i try booting to recovery or the rom.
jackrabbit72380 said:
ok used odin 10
tryied everything you said exactly phone reboots on samsung galaxy s5 boot logo everytime. Whether i try booting to recovery or the rom.
Click to expand...
Click to collapse
Which recovery tar did you Odin? You pulled the battery after Odin said PASS, then unplugged the phone, put battery back in and immediately tried to get into recovery? If so, I'm stumped.
Ramer said:
Which recovery tar did you Odin? You pulled the battery after Odin said PASS, then unplugged the phone, put battery back in and immediately tried to get into recovery? If so, I'm stumped.
Click to expand...
Click to collapse
Yes I tryed
I pulled the battery after Odin said PASS
Yes I tryed
kt_twrp_recovery_boa6_firmware.tar
and
openrecovery-twrp-2.8.4.0-klte
and
philz_touch_6.57.8-klte
NOTHING!
when ever i try and boot the rom the phone vibrates 2 times and resets.
when ever i try to boot to recovery
i get
recovery booting....
recovery is not seandroid enforcing
set warranty bit : recovery
then phone reboots.
then it trys to boot the rom.
and vibrates 2 times and resets.
Im not new to using odin or flashing roms or recoverys i sort of know what im doing. not to sound cocky.
Im Stumped to!
jackrabbit72380 said:
Yes I tryed
kt_twrp_recovery_boa6_firmware.tar
and
openrecovery-twrp-2.8.4.0-klte
and
philz_touch_6.57.8-klte
NOTHING!
Im not new to using odin or flashing roms or recoverys i sort of know what im doing. not to sound cocky.
Im Stumped to!
Click to expand...
Click to collapse
I saw your post count, I knew you knew what you're doing, just wanted to double check everything. Sorry, I'm out of ideas. I did ask @tdunham to take a look at this thread, if he has some other ideas, but he's offline right now. Hopefully he'll check in later.
What about flashing back to an older version of android? Full tar flash.
---------- Post added at 12:38 AM ---------- Previous post was at 12:36 AM ----------
Like ne5, and nothing else, just see if you can get stock to boot, no messing around trying to flash recovery.
This is RWillco12's NE5 stock.. Have the phone in download mode and run the .exe
Thanks TD.
Ramer said:
This is RWillco12's NE5 stock.. Have the phone in download mode and run the .exe
Thanks TD.
Click to expand...
Click to collapse
I tryied ni3 already
but as far as i know you cant downgrade the bootloader.
if i could flash just the bootloader for ota6 maybe that would help.
i will try downloading ne5 now but my last rom was running a nkd modem.
im going to try and flash G900P_NKD_FullRestore.tar in odin if that dont work ill try ne5
and will report back shortly.
well nkd full restore boots up to
unknowen error!
wait..
done!
udc start.
power reset or
unknown
upload mode.
this is the way i got it back from retech after they replaced my bezel and digitlizer and screen
i never had an issue with anything software wize before that.
Have you tried flashing the phone without any sim cards inserted including the sprint card? You are flashing from a powered off state right? You know it wont work unless phone is powered off before going into download mode.
As a last resort attached is the pit file for the 16gb G900P. Unzip and put it into the pit section of odin and flash the stock firmware again. It will repartition the entire phone when it flashes the stock image.
tdunham said:
Have you tried flashing the phone without any sim cards inserted including the sprint card? You are flashing from a powered off state right? You know it wont work unless phone is powered off before going into download mode.
As a last resort attached is the pit file for the 16gb G900P. Unzip and put it into the pit section of odin and flash the stock firmware again. It will repartition the entire phone when it flashes the stock image.
Click to expand...
Click to collapse
Yes I was using the pit file and yes I know to go to download mode from power off state. and no sim card is in the phone.
flashing ne5 stock with fingers crossed.
brb
nope
is there any bootloaders only i can flash?
well tryed everything all it does is vibrate 2 times. same as be4 im dead in the water. i don't know what's wrong or what to do.
I have tryed everything i can think of.
I can boot to download mode and flash anything i want but nothing works.
no recovery. no rom.
Hi guys,
I have flashed SD recovery over Exynos (idiot - I know!)
Have I got any chances to recover the device?
I have got g930f.
Bootloops at Samsung Galaxy S7 logo.
Will boot to download mode, visible in odin but upon flashing anything it will immediately restart and odin will FAIL.
Anything to revive this brick?
Thanks!
bednim said:
Hi guys,
I have flashed SD recovery over Exynos (idiot - I know!)
Have I got any chances to recover the device?
I have got g930f.
Bootloops at Samsung Galaxy S7 logo.
Will boot to download mode, visible in odin but upon flashing anything it will immediately restart and odin will FAIL.
Anything to revive this brick?
Thanks!
Click to expand...
Click to collapse
Hi mate
Probably yes....
You could try to reflash the correct recovery first.....
Custom like TWRP
Check here
Or the original one
Check here
Worse case scenario flash a stock rom (odin) Use all 4 files AP, BL, CP and home_csc to try to save your data ( has to be the same as you have in your phone now) or CSC this will give you a clean installation
Check here
MAX 404 said:
Hi mate
Probably yes....
You could try to reflash the correct recovery first.....
Custom like TWRP
Check here
Or the original one
Check here
Worse case scenario flash a stock rom (odin) Use all 4 files AP, BL, CP and home_csc to try to save your data ( has to be the same as you have in your phone now) or CSC this will give you a clean installation
Check here
Click to expand...
Click to collapse
Thank you,
For whatever reason - donwload mode is somehow corrupted. As soon as I'm starting to flash anything it fails and restarts the phone...
Any other options I could possibly have?
Thanks!
bednim said:
Thank you,
For whatever reason - donwload mode is somehow corrupted. As soon as I'm starting to flash anything it fails and restarts the phone...
Any other options I could possibly have?
Thanks!
Click to expand...
Click to collapse
What error do you get in Odin, check the logs.
Did you try flashing from another PC
re install driver
Un install Kies or smart swicth
Different USB cable
What odin version are you using
MAX 404 said:
What error do you get in Odin, check the logs.
Did you try flashing from another PC
re install driver
Un install Kies or smart swicth
Different USB cable
What odin version are you using
Click to expand...
Click to collapse
Nope, I haven't tried different pc/cable as the very same pc was ok to flash wrong recovery 5min earlier...
I don't have kies installed, I just had samsung drivers which were always working for me.
I am 100% positive its not pc fault just me being an idiot...
I am using odin 3.12
Thank you
bednim said:
Nope, I haven't tried different pc/cable as the very same pc was ok to flash wrong recovery 5min earlier...
I don't have kies installed, I just had samsung drivers which were always working for me.
I am 100% positive its not pc fault just me being an idiot...
I am using odin 3.12
Thank you
Click to expand...
Click to collapse
We are all idiots at one point or another
Just want to point out different reason why odin may fail...
See what error do you get when flashing with Odin...and what files are you using when it fails to flash
MAX 404 said:
We are all idiots at one point or another
Just want to point out different reason why odin may fail...
See what error do you get when flashing with Odin...and what files are you using when it fails to flash
Click to expand...
Click to collapse
I can't check it right now ( I'm at work) but it basically gives me fail on red backdrop. Can't remember what it says in the log, but definitely says Success: 0/ fail: 1
Last file I tried to flash was whole system rom. Just before that, I tried to flash TWRP for s7 exynos - the correct one but it failed. And, of course, it all started with flashing incorrect twrp which went through perfectly :/
Thanks
bednim said:
I can't check it right now ( I'm at work) but it basically gives me fail on red backdrop. Can't remember what it says in the log, but definitely says Success: 0/ fail: 1
Last file I tried to flash was whole system rom. Just before that, I tried to flash TWRP for s7 exynos - the correct one but it failed. And, of course, it all started with flashing incorrect twrp which went through perfectly :/
Thanks
Click to expand...
Click to collapse
When you get home, just try installing "Samsung Smart Switch" (it's no longer Kies) (http://www.samsung.com/sg/support/smartswitch/Smart_Switch_pc_setup.zip)
I understand that you already have drivers on your PC, but the Samsung Smart Switch might come with some updated drivers for your Samsung S7, which might change the scenario. Installing that, plus using another version of Odin (run it as Admin). I used this one just today. (http://dl.sammobile.com/Odin3-v3.11.1.zip)
If the flashing the recovery still fails, try flashing Stock rom under AP like suggested earlier. If that still fails.
Use Samsung Smart Switch's "Emergency recovery" but do the Initialization (2nd tab) by inputting your Phone model and let Smart Switch download the official firmware from Samsung's servers.
This must be done while your phone is in Download mode, so make sure you have enough juice to wait out the download process.
Good luck!
My phone is not working at all, it just sits in a bootloop. Samsung switch doesn't have my model, nor does their website. I've tried to flash the stock rom on my phone and it doesn't work. The only way it flashes is if I delete cm.bin and sboot.bin other wise it will just fail in odin. My phone is not supported that much I guess but even when I try to flash custom roms on my phone it is successful in twrp recovery but stays in a boot loop after restart. I don't know if I need to buy a new phone because for the last week I've been trying to fix a 200$ brick. Please help is there any other way to flash stock firmware other than odin. I've tried diffrent cables, ports, the whole works. What do I do?
Ethan Mobile Tech Nerd said:
My phone is not working at all, it just sits in a bootloop. Samsung switch doesn't have my model, nor does their website. I've tried to flash the stock rom on my phone and it doesn't work. The only way it flashes is if I delete cm.bin and sboot.bin other wise it will just fail in odin. My phone is not supported that much I guess but even when I try to flash custom roms on my phone it is successful in twrp recovery but stays in a boot loop after restart. I don't know if I need to buy a new phone because for the last week I've been trying to fix a 200$ brick. Please help is there any other way to flash stock firmware other than odin. I've tried diffrent cables, ports, the whole works. What do I do?
Click to expand...
Click to collapse
you can try bro using samfirm to find your latest firmware
you can find latest one from here
https://forum.xda-developers.com/attachment.php?attachmentid=3803841&d=1467715462
1-after flash latest firmware
2-flash your model TWRP by odin but without tick auto-restart after that
3-restart your device manual by press VOL-DOWN + HOME + POWER Button then after screen turn to black CHANGE JUST TO VOL-UP to enter TWRP RECVERY
4-flash Latest SUPER-SU BY TWRP
rifek4 said:
https://forum.xda-developers.com/ga...ow-to-root-install-twrp-t3673742/post73811927
Click to expand...
Click to collapse
ty very much but my model is not supported
Hello guys,
after days of reading and trying i decided to open a thread.
I got my Samsung stuck on Erasing Screen after an update.
I tried to Flash Stock Rom via ODIN. The Flash passed but after Booting the device stuck on the Bluescreen with "Erasing" on the bottom.
I tried Flashing with Pit, and without. With Nand erase and without. With Re-partition and without.
I can not access recovery with VOL UP + Home + Power.
Device is not rooted.
I am very thankful for any advice.
Thanks in advance.
What model does your phone say in download mode, and what firmware did you flash?
Beanvee7 said:
What model does your phone say in download mode, and what firmware did you flash?
Click to expand...
Click to collapse
Sorry,
it is a G930F
I downloaded the File from SamFirm (G930FXXU2ERE8_CL13438344_QB18102270_REV00) and used Odin3 v3.13.1.
any solutions?
I have exactly the same Problem.
Did you find a possibility to fix that ?
I´m going crazy with that my device is unrootet and on stock Rom when it came into bootloop , i tried to fix it with Odin a couple of times used the latest Firmware from Samfirm but it doesnt work and gets stuck on erasing Screen and keeps on restarting . I can always get into download mode but i cant open the recovery . Another thingis that my System Status in the download mode says custom ?? i never flashed a custom Rom on it Does anyone know if i can bring it back to Samsung like that because i still have a guarantee
i would be so thankful for your help guys
cheers
Had a similar issue before with an S6, and one of the workarounds that works for a lot of samsung issues is to flash the phone through ODIN with a repair firmware and a pit file. If im remembering right the firmware files are AP, CP, BL and CSC, also the pit file. you gotta check repartition in odin too.
any idea how to fix this ? In the same boat, can't figure out how to solve this.
same thing happened to me, i can't get it to work
spittfire said:
Hello guys,
after days of reading and trying i decided to open a thread.
I got my Samsung stuck on Erasing Screen after an update.
I tried to Flash Stock Rom via ODIN. The Flash passed but after Booting the device stuck on the Bluescreen with "Erasing" on the bottom.
I tried Flashing with Pit, and without. With Nand erase and without. With Re-partition and without.
I can not access recovery with VOL UP + Home + Power.
Device is not rooted.
I am very thankful for any advice.
Thanks in advance.
Click to expand...
Click to collapse
hi have you solved then? I've got the same problem
can´t believe there is no solutions for this
i have the same problem with a galaxy A20 SM-A205G
i flahshed diferrent ROMs from diferent countries, with PIT FILE and without it and nothing works
maybe the difference with other posters here is that i can access to recovery mode but i dont find anything about fix this phone from recovery mode or something like that.