I have a 2012 edition galaxy note 10.1 wifi. GT-N8010
I can only start it up and the black with white stripes screen shows up.
When I put it in chargeing the screen cames up again and can't turn it of. No charging lights or symbol.
I have early rooted this device so it coul run as 64gb memory from sd card, but after it have not been used abot 4 monts, it have been this now.
I can go into Odin mode when I push power and volume up. Then it says downloading mode. No notofication screen. No recovery screen when i push volume down. only the screen with white stripes. (see attachments)
The status i download mode is:
ODIN MODE
Product name:
Custom binary download: no
Current binary: samsung official
System status: Custom
I have tried to get it communicate with two pc's, but no ones finds it. No green com port in odin software on both pc's. I believe it's because I don't have usb debugging on. I can't activate that, because my pad not starts. No boot logo. How can I solve this. Please help.
I have installed all necessary drivers on both pcs.
Hey, did you find any solution to this problem? I had this same issue in my 10.1 but don´t seem to find what the problem is.
ASA OP has not been on the forum since 2015 you are asking a ghost.
The answer for the OP would be flash stock rom through Odin .
Upgrade Fail - Samsung GT-N8010
:crying:
I have a similar problem needing to updrade Android to Kit Kat on my Samsung Note 10.1 (GT-N8010). I bought the unit in the UAE and am now in Australia. I turns out that I need the UAE version (XSG). Downloaded and then
Entered C:\Users\chris\Downloads\N8010XXUDNF3_N8010OJVDNF3_XSG\N8010XXUDNF3_N8010OJVDNF3_HOME.tar.md5 in AP Window
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 1794 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Tablet is showing "Downloading....Do Not Turn off Target"
Any Ideas would be greatly appreciated
White stripped screen ??
sboot.bin fail
Reasons .
Sboot.bin is failing because the ROM is not for your phone, the bootloader in the phone is newer than the bootloader in the ROM,
you need to use the original Samsung USB cable, or a different USB 2.0 port.
Cannot Upgrade Android on Samsung Galaxy Note 10.1 (GT-N8010)
Thanks for the response would you suggest another thread for this problem? I get the white screen intermittently.
I am using the original cable and have tried all three USB ports on the laptop. I am using the right file in the AP section? C:\Users\chris\Downloads\N8010XXUDNF3_N8010OJVDNF3_XSG\N8010XXUDNF3_N8010OJVDNF3_HOME.tar.md5
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 1794 M
<ID:0/006> SetupConnection..
<ID:0/006> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 1794 M
<ID:0/006> SetupConnection..
<ID:0/006> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 1794 M
<ID:0/005> SetupConnection..
<ID:0/005> Removed!!
<ID:0/005> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 1794 M
<ID:0/003> SetupConnection..
<ID:0/003> Removed!!
<ID:0/003> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
Can't open the serial(COM) port.
Try removing Kies and installing Samsung USB drivers .
Check
1. You are using an original quality USB cable and not a thinner USB charging cable.
2. You are connecting directly to the PC USB port and not through a USB hub.
3. Try another PC USB port.
4. Try another Odin version.
Related
Sorry to say, i tried to root Samsung GT-I9300 with help of Odin and CF-Autoroot, but got similar Messages as glenf (http://forum.xda-developers.com/showthread.php?t=2202563) and got stuck - no way to reaktivate handy (stockrom) but could manage to activate downloadmode .
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
.....
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write start!!
<ID:0/004> cache.img
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I used Odin 3.04 and CF-Auto-Root-m0-m0xx-gti9300.tar.md5 .
I rmoved battery to get into download mode again and tried to use Odin with a stockrom - the same effect.
I had a stockversion 4.3 MAX-I9300XXELLA-20130104192229 and thougt it would work to root - as in thread http://forum.xda-developers.com/showthread.php?t=1957273&page=63.
Anyone who can help me,Samsung is new to me, i did rooting and custom roms on HTC before, never had problems. I did not find a way out.
Regards Manfred
lavgold said:
Sorry to say, i tried to root Samsung GT-I9300 with help of Odin and CF-Autoroot, but got similar Messages as glenf (http://forum.xda-developers.com/showthread.php?t=2202563) and got stuck - no way to reaktivate handy (stockrom) but could manage to activate downloadmode .
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
.....
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write start!!
<ID:0/004> cache.img
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I used Odin 3.04 and CF-Auto-Root-m0-m0xx-gti9300.tar.md5 .
I rmoved battery to get into download mode again and tried to use Odin with a stockrom - the same effect.
I had a stockversion 4.3 MAX-I9300XXELLA-20130104192229 and thougt it would work to root - as in thread http://forum.xda-developers.com/showthread.php?t=1957273&page=63.
Anyone who can help me,Samsung is new to me, i did rooting and custom roms on HTC before, never had problems. I did not find a way out.
Regards Manfred
Click to expand...
Click to collapse
hi im having a similar problem with my s3 gt-19300.
its not rooted . suddenly it just went dead
and using samsung kies it failes after downloading the os.
using odin i get the following.:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGMJ9_I9300VFGGMJ5_I9300BUUGMJ3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> cache.img
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
any help??
Hey guys,
exactly the same Problem here... Tried diffrent USB ports, Odin versions and cables...
<OSM> CF-Auto-Root-m0-m0xx-gti9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> recovery.img
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
The reason I was rooting mainly was being unable to copy files to my phone... wtf. If you have any other solution for that on hand, I couldn't care less about rooting, so shoot
Thanks in Advance
Sorry to hear you're having problems try using Odin 3.07 instead of 3.04 worked for me.
Sent from my D5803 using XDA Free mobile app
Hi, i have a Norwegian Samsung Galaxy S6 and tried to root it using the SM-G920F files from CF-Auto-Root but it didnt work and now my phone wont start with the message: "Recover is not seandroid enforcing" where it says "Samsunng Galaxy S6
Powered by Android". I have tried all the SM-G920F Stock firmwares here but unable to install them, maybe my device should have been rooted before this? Is there i way i can fix my phone now? I cant even shut it down anymore :/
I have tried to follow this guide: autoroot.chainfire but it didnt work and now i have tried to use the UK/spain/Every-Stock-Firmware-for-the-G920F-i-Can-Find.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920FXXU1AOCZ_G920FVFG1AOC4_G920FXXU1AOCW_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
On the phone itself it says "SW REV. CHECK FAIL. DEVICE:2 BINARY:1
With red text.
Is what ODIN3 v3.10 is saying.
To shut down S6 from download mode press volume down + power button at the same time and hold until screen turns off.
After this you have an option to:
1. Bring your S6 bacck to Samsung for warranty repair.
2. Use a different USB cable or try a different USB port then reflash again.
I hope this helps.
roydok said:
To shut down S6 from download mode press volume down + power button at the same time and hold until screen turns off.
After this you have an option to:
1. Bring your S6 bacck to Samsung for warranty repair.
2. Use a different USB cable or try a different USB port then reflash again.
I hope this helps.
Click to expand...
Click to collapse
It Says KNOX warranty void 1, this means that warranty is broken? I am going to get my original samsung s6 USB cable tomorrow to try.
Install twrp and port any costum room and you will fix your s6...
Or download newest version in sammobile of g920f stock firmware. You are failing at sboot. That mean bootloader in the phone os newer than the one you trying to install
Now it does not fail right away, but it still fails after a short while. Will the process fail if i don't do anything on the device itself? Because now it starts doing something in Odin, but returns fail after a while, but i am not with the phone as it is home right now.
This is what ODIN says now:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920FXXU2BOFL_G920FOJV2BOEE_G920FXXU2BOFJ_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> modem.bin
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Try redownloading your ROM. There might be errors in the file resulting from the download.
Hello,after doing a mistake I soft-bricked my S6 G920F.The phone's screen displays the following error: "An error has occureed while updating the device software".If I want to restore it back to the original software via Smart Switch,there's another thing: After the first stage of downloading the files at 85%,it goes to stage 2,but here's the main problem: It's stuck at 0%,and later comes with the error that It couldn't recognize the software update mode.But that's not the only thing:Sometimes during the Initialization Process (I think it's the 10th attempt) the screen just turns black,and turns normal to the error screen,and so on.First time when I had this problem,it worked fixing it cuz I was following this video https://www.youtube.com/watch?v=ADVXj1vsRk8 but now I don't think is working anymore.I tried everything but still no results this time.Is my phone dead?I tried many times via Smart Switch,but same and same thing happens,like I said before.What should I do?
UP
When Trying to flash original firmware via ODIN
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1101)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
Fixed.I had to put Lord Gabriel's song in order to make it work
Hello to everyone!! it is my first post and i hope this has not been answered elsewhere.
my phone is a samsung galaxy s6 with android 7 and G920FXXU6ERF6 baseband version
i am trying to root my phone with odin v3.13 because i want to Unlock Forgotten Private Mode PiN/Password/Pattern by this guide https://forum.xda-developers.com/general/security/guide-unlock-forgotten-private-mode-pin-t3758011
i have enable the developer mode on my device and open the usb debugging mode but i cant find the oem unlocking.
i am using this guide https://forum.xda-developers.com/chef-central/android/how-to-root-galaxy-s6-sm-g920f-t3079145.
i am loading the AP file that i found on your guide.
And now it is the time to press start. after that the program returns
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 66 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
https://ibb.co/XsDPmbx
Hello,
My phone is rooted. I have disabled Developer mode (USB debugging or whatever there). After restart I got message "custom binary blocked by frp lock" and can't turn it on.
I have access to recovery mode (Home+Power+Volume UP) and access to firmware download more (Home+Power+Volume Dn). That's all.
In recovery mode I see my phone details:
7.0/NRD90M/G935SKSU1DQG1
and CSC: TGY
After reading multiple forums and advises I have installed in my laptop Odin (3.14.4), Samsung drivers, downloaded firmwares from samfw.com. I didn't find this specific firmware for my CSC (TGY) but tried many similar. Anyway, nothing worked. Either I get error like this:
<ID:0/004> Odin engine v(ID:3.1401)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 4329 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004>
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Click to expand...
Click to collapse
Or like that:
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 4941 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Please advise what can be done? I can't allow to lose my data. What other options I have? Thanks.
Who are those people saying data will be saved after firmware upgrade???
****.. lost everything!