Database Info

[Q] micromax a110 is not working

hey there..i need some serious help!!! my micromax a110 is not working:crying::crying: it so happened that my cell suddenly got switched off..n den when i tried to switch it on it didnt start. just the starting screen appears and then it goes dead..then again the starting screen appears and it goes dead:crying::crying::crying:..please help me!!!! someone??? anyone???

try getting into recovery (vol + or - and pwr) and make a full wipe. if it will not power on, try flashing a new firmware. make sure you got the right one!

if u have cwm added then try to go to recovery n flash any custom rom of C2
if not then
Flash Stock rom using Sp tool it will Solve ur problem

dewdrops said:
hey there..i need some serious help!!! my micromax a110 is not working:crying::crying: it so happened that my cell suddenly got switched off..n den when i tried to switch it on it didnt start. just the starting screen appears and then it goes dead..then again the starting screen appears and it goes dead:crying::crying::crying:..please help me!!!! someone??? anyone???
Click to expand...
Click to collapse
I think it's out of charge, just plug in the charger and see what happens..

yog12 said:
if u have cwm added then try to go to recovery n flash any custom rom of C2
if not then
Flash Stock rom using Sp tool it will Solve ur problem
Click to expand...
Click to collapse
i tried doing that but thats not working...can you please tell me the procedure?

Lets Start
dewdrops said:
i tried doing that but thats not working...can you please tell me the procedure?
Click to expand...
Click to collapse
1)Install Drivers.
2)Open SP tool
3)Select 'Android Scatter file' inside ROM folder.
4)Click Firmware->Upgrade Button.
5)Connect Phone{Switched off} to PC via USB Cable.
6If everythings right,Flashing will proceed..
7)Wait till It finishes..A green ring is displayed on completion..
8))Now Close SP tool..Remove Phone from PC..
9)Switch ON the phone...It is successfully Flashed...:laugh:

I also face same problem some time when I make Factory or DRM reset
Green Android Robo with rotating frame
Start again and again. No switch off .. No effect after remove battery..
Only 1 solution "Do flash with SP Tool"

dewdrops said:
i tried doing that but thats not working...can you please tell me the procedure?
Click to expand...
Click to collapse
Hey no worries.. just follow my dis thread 'unbrick bricked canvas 2' :thumbup:
Link: http://forum.xda-developers.com/showthread.php?t=2376667
hit thx if i helped...

[Q] A110q not running

hello friends. my micromax canvas 2 plus is not running now... i am looking forward to find this solution as early as possible
my micromax canvas 2 plus is not running now, it shows only canvas logo and nothing appears, and this all happens because today i tired to install new ROM - Color-Os_V.1.2_3.zip, for that, i follow all steps from
http://forum.xda-developers.com/mic...tom-rom-color-os-rom-micromax-canvas-t2585464
, but not able to install.. during recovery mode i got error that update is abort ... i thought that may be increasing partition will help so i tried using SP flash on window xp and followed steps as discuss
http://forum.xda-developers.com/mic...q-canvas-2-t2568182/post48447661#post48447661
but after that i got "sp flash tool error 8038" and since not able to run canvas 2 plus, it shows only canvas logo and nothing happens
when i tried to use recovery mode again by pressing together "power, + volume, - volume button" i see that error saying not able to
E mount sd card
please help me friends

i think i might have done something wrong
i guess i did format first by using SP FLASH .... please someone provide me files that i need to install using SP FLASH

prakash001 said:
hello friends. my micromax canvas 2 plus is not running now... i am looking forward to find this solution as early as possible
my micromax canvas 2 plus is not running now, it shows only canvas logo and nothing appears, and this all happens because today i tired to install new ROM - Color-Os_V.1.2_3.zip, for that, i follow all steps from
http://forum.xda-developers.com/mic...tom-rom-color-os-rom-micromax-canvas-t2585464
, but not able to install.. during recovery mode i got error that update is abort ... i thought that may be increasing partition will help so i tried using SP flash on window xp and followed steps as discuss
http://forum.xda-developers.com/mic...q-canvas-2-t2568182/post48447661#post48447661
but after that i got "sp flash tool error 8038" and since not able to run canvas 2 plus, it shows only canvas logo and nothing happens
when i tried to use recovery mode again by pressing together "power, + volume, - volume button" i see that error saying not able to
E mount sd card
please help me friends
Click to expand...
Click to collapse
Proper drivers were not installed while flashing... Install the drivers and try again, else directly flash the stock rom using this guide www.droidarena.in/Thread-Stock-ROM-for-Micromax-Canvas-2-Plus-A110Q
Even I had bricked my phone partitioning once because of no proper driver...
IF nothing helps service centre is always there Good Luck

Hard bricked when flashing

I was trying to root my unite 2 using sp flash tools but it failed and my mobile is not switching on even it is not getting charged but it is detected by pc.Can someone tell any solution

jeevan123 said:
I was trying to root my unite 2 using sp flash tools but it failed and my mobile is not switching on even it is not getting charged but it is detected by pc.Can someone tell any solution
Click to expand...
Click to collapse
If its detected by PC, then using SP flash tools, try flashing a new ROM again... and it should be back to normal again....

when iam flashing to my mobile error occurred that ERROR 4032 : Enable DRAM failed! what i do >? plz help me i am downgrading to lollipop to kitkat help me please

Did anyone found the solution?

i need the same information
i am also unable to format my previous rom...................

plz help
i have micromax unite 2.my phone was hard bricked.and i tooked it to the repair shop where he opened my phone,did something wit it then next day he returned me my phone saying it will not work.....after few days i again tried sp flash tool to just gave it a check and i was able to flash new rom to it .now my phone is booting up i heard the bootup sound,even the volume rockers are working but it is showing nothing on the screen .what would be the problem....plz help

[email protected] said:
i have micromax unite 2.my phone was hard bricked.and i tooked it to the repair shop where he opened my phone,did something wit it then next day he returned me my phone saying it will not work.....after few days i again tried sp flash tool to just gave it a check and i was able to flash new rom to it .now my phone is booting up i heard the bootup sound,even the volume rockers are working but it is showing nothing on the screen .what would be the problem....plz help
Click to expand...
Click to collapse
take it to micromax care they will flash stock software to it . i had same problem a year ago

My Micromax A106 Unite 2 is dead After Flashing ROM

Yesterday i attempted to flash my micromax a106 unite 2 using sp flash tool. I am new to flashing and it was my third attempt(first lenovo,then samsung and now micromax) to flash a rom. But this time the flash went wrong somewhere, and now phone is not turning on or even charging. I can feel the heat from the camera part inside the phone, so i assume its working. Any chance of saving it??? I cant also flash the phone now. It says
BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (2005)
[BROM] Can not pass bootrom start command! Possibly target power up too early.
After some minutes of clicking the download button in sp flash tool.
I installed the mtk usb drivers too. I can heard the pc making connect sound once usb is inserted and also hear disconnecting too...Please do help me.

Is the problem solved?

Micromax A106 Unite 2 dead After Flashing
My Micromax A106 Unite 2 is dead After Flashing not power on plzzz help me :crying:

santoshk155 said:
My Micromax A106 Unite 2 is dead After Flashing not power on plzzz help me :crying:
Click to expand...
Click to collapse
Explain in brief what have u done that leads to the problem (dead of phone)?
Flashed what?
Flashed using sp tool or some app?
Explain your problem in deep so that i or anyone else can help
Don't worry no mobile can be permanently dead, we just have to flash the stock ROM of the respective mobile:fingers-crossed::good:

help,i got hard bricked my Micromax canvas Knight2(E471)

I think i flashed the wrong ROM by mistake in canvas knight2 by twrp and after completing the installation there was option to reboot the phone and after tapping on it the phone becomes dead completely, nothings happening while pressing the power button , not going in recovery mode and don't showing the charging logo when I put it on charge , plz somebody help me :crying:

nishkarsh3696 said:
I think i flashed the wrong ROM by mistake in canvas knight2 by twrp and after completing the installation there was option to reboot the phone and after tapping on it the phone becomes dead completely, nothings happening while pressing the power button , not going in recovery mode and don't showing the charging logo when I put it on charge , plz somebody help me :crying:
Click to expand...
Click to collapse
I think you hard bricked your android. First connect your android to PC via USB and check it detects Qualcomm 9008 port in device manager. If yes then use qfil tool to flash your stock os to your android.

my phone micromax canvas night 2 hardbrick. dont show the boot logo.only show the penkin photo phone switch on mode...flashing proceess is compleate but dont boot the device only vibrate and show the penkin photo...what is this problem my phone please help...only fast boot flashing available in net any other flashing process in this phone ...so please help..