Database Info

[HELP]seems bricked :(, or idduno please help :(

i have a Samsung Galaxy sl ..
at no reason while im texting , the messeging force close ..
many times .. then the phone rebooted it self .i dnt know why ..
when suddenly , it its rebooting over and over again ..
then i tried on some thread the wipe all , factory reset at the recovery mode ..
all of that doesnt work..
and this day .. i tried on some sites says ..
flash and asian froyo first then the GB dxkp7..
i followed all of the instructions .. and at the odin
they both okay and pass ..
after that .. the phone start itself
and now it stucks at the samsung logo .. its blinking like hell..
now i dont know what to do .. please help guys ..

jedd07r said:
i have a Samsung Galaxy sl ..
at no reason while im texting , the messeging force close ..
many times .. then the phone rebooted it self .i dnt know why ..
when suddenly , it its rebooting over and over again ..
then i tried on some thread the wipe all , factory reset at the recovery mode ..
all of that doesnt work..
and this day .. i tried on some sites says ..
flash and asian froyo first then the GB dxkp7..
i followed all of the instructions .. and at the odin
they both okay and pass ..
after that .. the phone start itself
and now it stucks at the samsung logo .. its blinking like hell..
now i dont know what to do .. please help guys ..
Click to expand...
Click to collapse
RELAX..!!! take a deep breath...
hv a glass of cold water..
and now ur ready to go...
i want u to dwnload
xxkpe...firmware...
flash it...
after it flash any other gingerbread dxkp7 or xxkpq u want too...
for gingerbrd to work..u need xxkpe as a base..NOT FROYO...
so..
i hope u knw hw to use odin since u hv mentioned about odin in d op...
if not here is what u do..
1.Dwnload XXKPE..from stock roms thread...
and do this..all credits to kkrraazzyy
2. Run Odin3 v1.83
3. Check Re-Partition, Auto Reboot and F. Reset Time.
4. Click PIT button and select this file: latona_20110114.pit
5. Set it to download mode : Press Volume down + OK first, then hold Power button.
6. Connect USB cable and the program will detect the phone's Com number.
7. Click Start button to download the PIT file to phone.
8. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir]
9. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
11. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
12. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
13: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!]
14. Click Start button to flash these files to phone.
15. Do not touch anything till you see PASS on the program window.
u hv an issue..free to ask...

okayyyy
ok ..
i downloaded xxkpe .. and i flashed it already..
do i need to download dxkp7 or xxkpq ?
coz i think nothing happen and change ..
-------------
but on the guide youve given , i open the odin , then put the cable first before opening the latona .. i think that is not an issue

jedd07r said:
ok ..
i downloaded xxkpe .. and i flashed it already..
do i need to download dxkp7 or xxkpq ?
coz i think nothing happen and change ..
-------------
but on the guide youve given , i open the odin , then put the cable first before opening the latona .. i think that is not an issue
Click to expand...
Click to collapse
not an issue...
xxkpq is the latest..with NO BUGS...and most stable..
or u cn try ddkp3 too...
Much better thn xxkpe..
if i helped hit thank you button..

:/
i follow all steps in guide ..
but i think there is p problem on this 2 in system recovery ..
i see them always, like after flashing it will proceed in recovery mode , right ..?
then i see this one
E:error in data/log/recovery/kernel_log.txt .. if im not mistaken thats a red text on my sys rec everytime i reboot my phone ..
and the other one is the
Cant access to '/system/csc/XTC/system/'.
i think this is the main problem of this ..

this what happen..
this the error i got .. even i flash any frimware .. i think the red text is the main problem..
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

jedd07r said:
this the error i got .. even i flash any frimware .. i think the red text is the main problem..
View attachment 1025365
Click to expand...
Click to collapse
can u tell me wat u r tryng to do step by step pls...
if ur confused..
pls Start from the scratch... KPE...twice thn kpu..
if u still feel any problms..thn u can flash Froyo using ODIN..from stock roms threads..
th kpe..and thn..ur desired firmware..
i hope it works..
Pls verigy the froyo part m not sure about it.do some google..or XDA is the best pace...

okay ill try
okay i will do it ..
but do you think the red text will be remove after flashing those frimware..
?
or there is a option like ultimate super factory reset ? like that ..
coz when i go to boot into recovery i saw those files in my internal sd ..
so i think flashing frimware doesnt remove my old files ..
can i make a video for you to see what is happening to my phone and , my steps of flashing frim , maybe im doing it wrong ..
:|

jedd07r said:
okay i will do it ..
but do you think the red text will be remove after flashing those frimware..
?
or there is a option like ultimate super factory reset ? like that ..
coz when i go to boot into recovery i saw those files in my internal sd ..
so i think flashing frimware doesnt remove my old files ..
can i make a video for you to see what is happening to my phone and , my steps of flashing frim , maybe im doing it wrong ..
:|
Click to expand...
Click to collapse
dude...
format us usb storage aell as memory card...
TAKE PRIOR BACKUP..!
i hope it helps...
else service centr...
but if the phone is working without any issues y worry?

:|
sorry guys , but i did all my best but i ddnt fix my phone ..
i almost downloaded all frimwares at samfrimware but i nothing ..
thanks for time greekynoob ill hit the thanks button for you ..
*le me hopeless :|
maybe tom is the right time to go at samsung store :'( :'( :'(

jedd07r said:
sorry guys , but i did all my best but i ddnt fix my phone ..
i almost downloaded all frimwares at samfrimware but i nothing ..
thanks for time greekynoob ill hit the thanks button for you ..
*le me hopeless :|
maybe tom is the right time to go at samsung store :'( :'( :'(
Click to expand...
Click to collapse
tried my best brother...
flash to stock rom before going to samsung store..
else u knw...
umm..its geekynoob.. not greeky..

[ROM] Alcatel Onetouch Flash (6042D) Stock ROM

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Alcatel Onetouch Flash (6042D) Stock ROM
Installation:
1) Download here 6042D_Stock_Backup.rar (768MB)
2) Extract ROM
3) Download SP Flash Tools
4) Power off your phone
5) Open SPFT and click on "Scatter-loading", now choose the scatter file in the ROM archive
6) Uncheck Preloader.bin
7) Click on Download button
8) Now plug in your device with USB. Download should start. Wait till it finishes flashing (5 to 10 minutes according to your computer speed).
9) Unplug the cable, go to recovery mode (volume down + power till you see alcatel logo); wipe data & factory reset; then wipe cache partition.
10) Now reboot.​
Troubleshooting:
- If your phone is booting and reboot (infinite loop) and so can't be powered off, just click on Download button and plug it in; SPFT will detect it when it turn off. It won't turn on when SPFT initiates the flashing proccess.
- If you're stuck on bootlogo or bootanimation (bootloop). Just click on download button in SPFT, then plug in your phone. Now press the power button for 10s (or less) till SPFT detects it. Now release the button, flashing should start.
Notes:
- NEVER flash with "Preloader.bin" checked ! Unless your device is already HARD BRICKED! (Tip: If you still can boot to recovery, then your device isn't hard bricked. It's just soft bricked)
- You need MTK VCOM USB Drivers installed first! You can find plenty of tutorial on Google to do that

Thank you

in my 6042D.. i go to TWRP--->Wipe---> Formet data.. now in my phone only boot logo displays...
Now can i do....???

thank you very much dude.. god bless you

flashes successfully but phone wont turn on
My phone(6042d) gets flashed successfully each time and also passes memory test but the phone wont turn on. it is detectable by sp flash tools so i guess its not hard bricked but wat might be the issue?plz help me...

Prashanthz said:
My phone(6042d) gets flashed successfully each time and also passes memory test but the phone wont turn on. it is detectable by sp flash tools so i guess its not hard bricked but wat might be the issue?plz help me...
Click to expand...
Click to collapse
Can you see Alcatel Logo ?

Nonta72 said:
Can you see Alcatel Logo ?
Click to expand...
Click to collapse
no.. just plain blank.. no vibration nothing..

Prashanthz said:
no.. just plain blank.. no vibration nothing..
Click to expand...
Click to collapse
Flash the rom without preloader

Does this rom is stock or backup of any device.
Sir, i want to know one thing that this rom is stock (direct from manufacturer) or you backup it from any device. Please answer this ASAP.

GreatSingh said:
Sir, i want to know one thing that this rom is stock (direct from manufacturer) or you backup it from any device. Please answer this ASAP.
Click to expand...
Click to collapse
Good question...
It's Backup of my device.
Manufacturer didn't provide a stock rom because Alcatel guys are LAZY :laugh:

works but no imei
after many attempts it started but i dont have the imei yet, what should i do now?

Prashanthz said:
after many attempts it started but i dont have the imei yet, what should i do now?
Click to expand...
Click to collapse
Reflash stock rom again. It's the only way to restore your IMEI. Or use MTK Droid Tools to restore your IMEI if you previously made a backup.

solved.. thank you..
Nonta72 said:
Reflash stock rom again. It's the only way to restore your IMEI. Or use MTK Droid Tools to restore your IMEI if you previously made a backup.
Click to expand...
Click to collapse
Since i know my imei's i tried to apply it using Chamelephon app from playstore and it fixed the imei problem.
Thank you bro for the stock rom with root.i dint had to root.. :good::good:

Prashanthz said:
Since i know my imei's i tried to apply it using Chamelephon app from playstore and it fixed the imei problem.
Thank you bro for the stock rom with root.i dint had to root.. :good::good:
Click to expand...
Click to collapse
You don't need to write "Thanks".
Just click on the "Thanks" button under posts.

I could have a video of how to thank you

if anyone have problem in downloading from mega can use this mirror i created
https://drive.google.com/open?id=0B1mvphK9i_ZkYmVpWEdsa2M4V1k
* proper credits given in rar title *
-TechExhibeo

I can't find general discussion, development or apps and original development for alcatel one touch flash plus.
does anyone know the link?

TechExhibeo said:
if anyone have problem in downloading from mega can use this mirror i created
https://drive.google.com/open?id=0B1mvphK9i_ZkYmVpWEdsa2M4V1k
* proper credits given in rar title *
-TechExhibeo
Click to expand...
Click to collapse
Thank you buddy.
meliacentrum said:
I can't find general discussion, development or apps and original development for alcatel one touch flash plus.
does anyone know the link?
Click to expand...
Click to collapse
There isn't one.

Error
I'm getting an error that says: "initializing scatter file failed. Please check the name of scatter file which you load is legal." Please help.

Hi ,I am stuck off in flashing my alcatel 6042d ,actually i have done all the steps you mentioned above but by doing these steps when i switched On my phone it doesn't have any access to network also my bluetooth is not working and i also checked my IMEI and it is showing that IMEI not found.
Help me PLz

Guide : How to fix Software issues or Red light of death of Xperia C2305 / CS39H

So first off all what is red light of death It a hard brick state of Xperia C2305/CS39H and it is mostly caused when you are installing a cwm recovery and that won’t match the S1 boot version of your device. Also it is caused by software update not properly installed some errors or incorrect rom flashing not suitable for your device. So before starting to the repairing process read the notes.
Notes :
1. This is official way to recover the device so the warranty will not be voild.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2.. You can use this process for any Xperia device having software issues ,hard brick , soft brick or bootloops any errors can be fixed by this.
3. In this process your stock android will be reinstall and all your data will be wiped so before starting. Take a backup from dr fone brick data repair download link is attached below you can download it and I will soon make a tutorial how to use it.
4. It is a stock rom so if you have unlocked bootloader it will not work you have to use unofficial flash tool to flash the rom.
5. If you face any issues during installation replay me below. Also read everything before starting.
6. You can proceed to the fix
So here how to fix it !!
Required :
1. Bricked Xperia C2305 or CS39H (softbrick , hardbrick ,any software issue, bootloops)
2. Windows PC or Mac but this procedure is only for Windows PC
3. Good Usb cable or Original cable best
4. Charger 800 mah or more. best way use original charger
5. Xperia Companion installed ( download link below windows only)
6. Xperia C2305/ CS39H USB drivers installed( download link below)
7. Proper high speed internet ( 800 kbps or more best 2 mbhs)
8. Time aprox 4hrs or more up to your internet speed
NOTE : BEFORE STARTING THIS OPEN THE BACK COVER OF THE DEVICE AND TAKE SOMETHING POINTED AND PRESS THE RESET
BUTTON WHEN YOU ARE CONNECTED TO THE PC WITH GREEN LED SHOWING THIS WILL WIPE THE THIRD PARTY CWM OR ANY RECOVERY ON YOUR DEVICE. IF YOU DONT THE UNSUPPORTED RECOVERY WILL BLOCK THE INSTALLION PROCESS. ONCE DONE FOLLOW THE STEPS.
So here the steps :
STEP ONE : See wheater your device is charged 80 % or not it is necessary because when you are in download mode alot of battery is consumed . Battery will not charge directly because device is non stop getting in download mode while charging consuming all the battery what is charged so how to charge battery First see the above notification led is off or on it is beside the front facing camera if its is on then the device is on off it by holding power button for 15sec once led is off insert usb and charge it again the above red led will on again off it by holding power button for 15sec Note disconnect the charging usb from device before pressing power button. Repeat this for 1 or 2 hr. Once done go to next step.
STEP TWO : First install Xperia C2305 / CS39H USB driver and then download Xperia Companion on your PC and open it then hit software repair chose smartphone and the hit click here. Once done it will download the drivers. Once done go to step three.
STEP THREE : hold power button for 15 sec then leave power button and hold vol- and insert the usb abd connect to pc don’t leave it until Xperia Companion detect it and leave the vol- and press next i agree all then it will download the OS of your device. NOTE : KEEP IN MIND OS SIZE IS APROXIMATELY 700 MB SO DATA CHARGES MAY APPLY I AM NOT RESPONBLE IF YOU HAVE TO PAY MORE FOR DATA PROCEED AT YOUR OWN RISK . Once done go to step four.
STEP FOUR: Disconnect the Usb and the start the device. First time will take 15 min or more to boot then select language and all the step up you are done.
CREDITS :
Me ( for explaining how to do this)
Sony Mobile Communication ( for making Xperia Companion)
Wonder share ( for making dr fone )
HIT THANKS IF THAT WORKS AND COMMENT BELOW IF YOU HAVE ANY PROBLEM IN ANY PROCESS. I WILL HELP YOU ASASP.
Download links :
Xperia Companion :
http://www-support-downloads.sonymob...aCompanion.exe
Xperia C2305 / CS39H USB Drivers :
https://developer.sonymobile.com/downloads/drivers/xperia-c-driver/
Dr fone offical download page :
https://www.google.co.in/url?sa=t&so...ZVGc8N9D8wOZ-Q
THANK YOU FOR READING

What is the reason for sudden death ?
I never roooted or installed roms to my phone and it suddenly died ! No boot or recovery ! why ? Is there something wrong with sony's software ?My phone is xperia c2305 ... I took it to service center three times and after a few week from repairing it,it always dies again ? So if install a custom rom ,will the problem be gone ?I also want to know how to install the drivers ... I downloaded it but I don't know what to do with it.

Khalid Zaki said:
I never roooted or installed roms to my phone and it suddenly died ! No boot or recovery ! why ? Is there something wrong with sony's software ?My phone is xperia c2305 ... I took it to service center three times and after a few week from repairing it,it always dies again ? So if install a custom rom ,will the problem be gone ?I also want to know how to install the drivers ... I downloaded it but I don't know what to do with it.
Click to expand...
Click to collapse
This is because your mother board has some issues if you have ever hard ware damage this is not new thing. Installing custom rom is not different then using stock the custom rom for xperia c are just stock themed so better dont install but sometimes it might able to slove the issue try installing custom rom. And the thing how to install drivers on yout windows pc charge the battery as shown in my guide then connect the usb to pc the go to control panel you will see the device as unidentified device click on it then search for driver on internet it will surely fail to find the hit browse then select the un zip driver file and select the driver it will install it you are done hit thanks if it works best wishes.

Khalid Zaki said:
I never roooted or installed roms to my phone and it suddenly died ! No boot or recovery ! why ? Is there something wrong with sony's software ?My phone is xperia c2305 ... I took it to service center three times and after a few week from repairing it,it always dies again ? So if install a custom rom ,will the problem be gone ?I also want to know how to install the drivers ... I downloaded it but I don't know what to do with it.
Click to expand...
Click to collapse
There might be some problem with your Phone's hardware. If it's still under warranty, maybe the company can replace your device but at least they can try to repair it for free.

I did what the topic said but xperia companion gives me an error .. please heeeelp !!

Maxx_Yamano said:
For using Xperia companion without error you need a fast internet connection or else it will show UE installation failed it needs faster internet so its not fault of guide as I my self repair my Xperia C from Hard Brick.
Click to expand...
Click to collapse
I have a download rate reaches to 250 KB/s

Maxx_Yamano said:
Lol its too slow mine is 6 mb per sec speed
---------- Post added at 09:15 AM ---------- Previous post was at 09:13 AM ----------
Lol its too slow mine is 6 mb per sec speed which windows you are using also how much bits ? Tell me I will help you in troubleshooting also can u add the screen shot showing error
Click to expand...
Click to collapse
I am using windows 10 (32 bit)
Screenshot for the error ..

Maxx_Yamano said:
Lol its too slow mine is 6 mb per sec speed
---------- Post added at 09:15 AM ---------- Previous post was at 09:13 AM ----------
Lol its too slow mine is 6 mb per sec speed which windows you are using also how much bits ? Tell me I will help you in troubleshooting also can u add the screen shot showing error
Click to expand...
Click to collapse
Maxx_Yamano said:
Xperia Companion can't connect to server please uninstall it and download from my thread https://forum.xda-developers.com/so...fix-software-issues-red-t3578944/post72438460
Click to expand...
Click to collapse
okey , i will try

Maxx_Yamano said:
Xperia Companion can't connect to server please uninstall it and download from my thread https://forum.xda-developers.com/so...fix-software-issues-red-t3578944/post72438460
Click to expand...
Click to collapse
I tried twice but the download reaches to 1/3 of the bar then gives me the same error .

Maxx_Yamano said:
Xperia Companion can't connect to server please uninstall it and download from my thread https://forum.xda-developers.com/so...fix-software-issues-red-t3578944/post72438460
Click to expand...
Click to collapse
I tried twice but it reaches to the 1/3 of the bar then gives me the same error ..

Maxx_Yamano said:
Hey mody3bdo sorry for not answering you I was busy in making my ROM for XPERIA C now I am free I can help you out but for that I need to ask you some questions answer me ASAP so I could assist you
Q.
- Which PC you have ?
- Is your device C2305 ?
- Have you installed ADB drivers of your device ?
- Where it goes 1/3 does it started to download the OS means does it showed you to connect your device or you haven't yet installed just installzing ?? (This is very imp )
- Does your device Hard brick or Soft brick
---- ALSO YOU CAN CHECK UPDATED VERSION OF THIS GUIDE
OVER HERE https://forum.xda-developers.com/sony-xperia-c/help/how-to-fix-dead-xperia-device-reinstall-t3612413 ----
HIT THANKS TO SUPPORT ME & MY WORK ALSO DONT FORGOT TO COMMENT BELOW
Click to expand...
Click to collapse
-My pc ia an hp laptop and i tried to use xperia companion on my desktop pc but the same problem
-yup my device is c2305
-I couldn't install adb drivers as nothing appear in the device manager
- yup it starts to download the os after (initializing) and connecting my device
- i think its a soft break as it just gave me an error while booting (Encryption unsuccessful) So I booted into recovery and selected (WIPE DATA/FACTORY RESET) , So I got into a bootloop , it just stuck on SONY logo .. So I am trying to repaire it to face that error (UEupdatefailed UE2005)
Thanks for helping
Sent from my SM-G530H using XDA Labs

Maxx_Yamano said:
Hey bro don't worry there is a will there is a way remove the back cover of your xperia take some pin or pointed object then hit the rest button wait for some time if your device gets on you are ready if you have got your device stuck due to wipe data factory reset then its not a brick you are stuck on boot logo so might Wmshua works if you have ever flash it using it or else it useless try pressing reset switch back might help you
DON'T FORGOT TO HIT THANKS IF YOU LIKE ME POST THAT WILL HELP ME
Click to expand...
Click to collapse
I tried with a pen but i face a problem with wmshua (flash failed undefinied )
Sent from my SM-G530H using XDA Labs

Maxx_Yamano said:
Might be a hardware damage I would recommend to go to service shop they will flash it will take 250-500 ₹
Click to expand...
Click to collapse
Okey thanks man but is there any other method to try ? As the shops in here dont work on xperia c ?
Sent from my SM-G530H using XDA Labs

Sony c encryption unsuccessful
I use this guide and problem not solved
Any solve please?

Maxx_Yamano said:
Hello guys this guide is out dated ... If you wish to try it then just go to my guide over here : https://forum.xda-developers.com/so...fix-software-issues-red-t3578944/post72438460
HIT THANKS TO SUPPORT ME & MY WORK ALSO DONT FORGOT TO COMMENT BELOW
---------- Post added at 01:30 PM ---------- Previous post was at 01:23 PM ----------
Hey mody3bdo sorry for not answering you I was busy in making my ROM for XPERIA C now I am free I can help you out but for that I need to ask you some questions answer me ASAP so I could assist you
Q.
- Which PC you have ?
- Is your device C2305 ?
- Have you installed ADB drivers of your device ?
- Where it goes 1/3 does it started to download the OS means does it showed you to connect your device or you haven't yet installed just installzing ?? (This is very imp )
- Does your device Hard brick or Soft brick
---- ALSO YOU CAN CHECK UPDATED VERSION OF THIS GUIDE
OVER HERE https://forum.xda-developers.com/sony-xperia-c/help/how-to-fix-dead-xperia-device-reinstall-t3612413 ----
HIT THANKS TO SUPPORT ME & MY WORK ALSO DONT FORGOT TO COMMENT BELOW
Click to expand...
Click to collapse
hi, im in this same situation but after reading the replies i discovered I'm installing drivers not the proper way, thanks in somewhere in page 2. will try my luck again later today, I'm using win 7 32bit if that matters. also is there any other way to charge my device internal battery? I'm suspecting it's battery is almost depleted. coz everytime i connect my phone to usb, it shows unknown device with a steady red light indicates it recognize the device in my pc. but disappears around 10secs maybe as soon the led light starts blinking. if i charge the device in doesnt show any charging animation or led it just turn on by itself on sony logo then reboot on endless loop when charging on a wall charger

xperia companion give error
UEGetPhoneInfoMissungInfo this error msg is given by xperia companion

is there a guide for Xperia C3 Dual D2502?

I bricked my XPeria 5 ! I need ur knowledge plZ!!!

Hey guys
I was busy with rooting my xperia 5, everything worked but then i de-installed systemapps like carrier services and facebook,google apps. and the next thing it hang in boot up with only sony on screen??
Plz how can i recover the software, i tried sony companion with fastboot mode but because the bootloader is unlocked its redirected me to developer site on sony. also the 'emma tool' wouldn start for this phone ?
Can someone give me advice. i have no phone now and i had it new !!
may god be with u guys

casaaaoui said:
Hey guys
I was busy with rooting my xperia 5, everything worked but then i de-installed systemapps like carrier services and facebook,google apps. and the next thing it hang in boot up with only sony on screen??
Plz how can i recover the software, i tried sony companion with fastboot mode but because the bootloader is unlocked its redirected me to developer site on sony. also the 'emma tool' wouldn start for this phone ?
Can someone give me advice. i have no phone now and i had it new !!
may god be with u guys
Click to expand...
Click to collapse
did you try xperia flashtool yet you can flash the firmware from the program, but first you need xperifirm to download the necessary firmware for your device model, then create a bundle from xperia flashtool, finally flash the created firmware via flashmode.

casaaaoui said:
Hey guys
I was busy with rooting my xperia 5, everything worked but then i de-installed systemapps like carrier services and facebook,google apps. and the next thing it hang in boot up with only sony on screen??
Plz how can i recover the software, i tried sony companion with fastboot mode but because the bootloader is unlocked its redirected me to developer site on sony. also the 'emma tool' wouldn start for this phone ?
Can someone give me advice. i have no phone now and i had it new !!
may god be with u guys
Click to expand...
Click to collapse
Emma should work, it's for UB devices
Edit: if it doesn't, use Flashtool as aforementioned

When I do the volume down for flashing mode emma dont read the phone, something with a another version ?

casaaaoui said:
When I do the volume down for flashing mode emma dont read the phone, something with a another version ?
Click to expand...
Click to collapse
please try my advice

nolihowell said:
please try my advice
Click to expand...
Click to collapse
What is ur advice ?
Edit, I see ur advice im gonna try and let u know. Thank u!

casaaaoui said:
What is ur advice ?
Edit, I see ur advice im gonna try and let u know. Thank u!
Click to expand...
Click to collapse
yes please do let me know if it works.

@casaaaoui
Official tools (emma, xperia companion) are useless once bootloader is unlocked
I've been able to fix similar issue using newflasher (even though Xperia 5 is not officially supported):
- download firmware for your device model using xperifirm
- remove all .ta files (incl. those in subfolders)
- extract newflasher files to the same directory where firmware files are stored (appslog_X-FLASH-ALL-A2CD.sin, bluetooth_X-FLASH-ALL-A2CD.sin, .... newflasher.exe ... )
- connect device in flash mode - turn it off (in case of boot loops press and hold combo "volume up" + "power button" and wait till phone vibrates 3 times), after that press and hold "volume down" and connect phone to the PC (once led became green you can release "volume down" button)
- verify there's no driver issue in Device Manager
- run newflasher.exe, answer n (no) to all questions
- wait for "End. You can disconnect your device when you close newflasher", press enter and unplug your phone
xperifirm: https://forum.xda-developers.com/crossdevice-dev/sony/pc-xperifirm-xperia-firmware-downloader-t2834142
newflasher: https://forum.xda-developers.com/crossdevice-dev/sony/progress-newflasher-xperia-command-line-t3619426
Good luck

Is this working in xperia 5 901SO ??? I have tried this as u said!! But its bricked my phone hardly!!

Hello , i need your help .

I'm bought xperia L3 for like 20 bucks . The power button is missing but working and i can turn it on easy.
My question is , can i unlock bootloader to root my phone ?
Im asking this becouse:
1. No topics for xperia l3
2. On https://developer.sony.com/develop/open-devices/get-started/unlock-bootloader There is no xperia L3
3. I need to root becouse i want to remap butons so i can unlock phone on power button (I dont want to use app becouse of battery drain)
So if anyone can help i would be thankful
And yes , i checked *#*#7378423#*#* and bootloader unlockable : YES

try using flashtool: link to download