Related
Oh dear.....I hope I haven't destroyed my O3D....
I was attempting to install the V10D update, so used the backup I took right after rooting and installing ROM Manager to restore the phone to its status before installing the performance pack. If I tried installing the update OTA before this I just got an invalid package error.
So the restore went well and it rebooted fine. So I ran the update again, and it downloaded and appeared to install, but when the phone rebooted it just booted straight into the recovery. I tried to get it to reboot again, but again it just booted back into recovery.
Ok, nothing to worry about I thought, I just ran the restore again with the same restore point as before....but after it finished it's still booting back up into the recovery!!! No matter what I do the phone just seems to keep booting into the recovery menu. I've tried booting into emergency mode by powering the phone off, then holding the UP Volume key and holding power, but it doesn't seem to work.
Can anyone help? Please?
Lil update -
When powering off the phone and then connecting it to the USB cable, it automatically boots into recovery mode without me even touching the power button. At this point the LG Mobile Update detects the phone and advises me that there's an update available. I try to apply this, but after entering the SN and IMEI, it just gives me a message "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update". I get the same error if I use the recovery Phone option. This always happens at the download stage, so is it possible that it's just failing to download the update from LG rather than actually do anything with the phone?
Please don't tell me I've ruined my brand new phone!!
Unfortunatly, you've managed to do the same as I have... leave the phone for e a few days and wait for a rom that you can install via clockwork recovery, you'll have your phone up and running again. Dont do as I did and wipe the recovery from the phone, it will result in a total brick (or at least a brick till LG releaase a full rom update (could be months yet...).
Oh man, I'm panicking so much that I might have ruined the phone now.....
read this thread for more info... http://forum.xda-developers.com/showthread.php?p=15762389#post15762389
madshaun1984 said:
read this thread for more info... http://forum.xda-developers.com/showthread.php?p=15762389#post15762389
Click to expand...
Click to collapse
I'm not sure what I'm looking for there, I've looked through that thread but it doesn't seem relevant to the problem I'm having.
I have the same problem, if you put it into emergency mode you can update to 10d but then its even worse then you are stuck in the firmware update screen
tomorrow I leave on holiday and was planning for nice 3d pictures and movies but I am screwed...
Lagamorph said:
Oh dear.....I hope I haven't destroyed my O3D....
I was attempting to install the V10D update, so used the backup I took right after rooting and installing ROM Manager to restore the phone to its status before installing the performance pack. If I tried installing the update OTA before this I just got an invalid package error.
So the restore went well and it rebooted fine. So I ran the update again, and it downloaded and appeared to install, but when the phone rebooted it just booted straight into the recovery. I tried to get it to reboot again, but again it just booted back into recovery.
Ok, nothing to worry about I thought, I just ran the restore again with the same restore point as before....but after it finished it's still booting back up into the recovery!!! No matter what I do the phone just seems to keep booting into the recovery menu. I've tried booting into emergency mode by powering the phone off, then holding the UP Volume key and holding power, but it doesn't seem to work.
Can anyone help? Please?
Lil update -
When powering off the phone and then connecting it to the USB cable, it automatically boots into recovery mode without me even touching the power button. At this point the LG Mobile Update detects the phone and advises me that there's an update available. I try to apply this, but after entering the SN and IMEI, it just gives me a message "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update". I get the same error if I use the recovery Phone option. This always happens at the download stage, so is it possible that it's just failing to download the update from LG rather than actually do anything with the phone?
Please don't tell me I've ruined my brand new phone!!
Click to expand...
Click to collapse
Don't panic, I managed to totally brick my phone today and LG told me to send it back for DOA but I managed to recover it in the end.
My phone wouldn't show anything on the screen, it remained black so I can say your position sounds much better than mine.
What you will need:
USB Drivers - Download from here (Check note)
LG Mobile Support Tool (LGMST) - Download from here
Before you start: Disconnect the phone from the computer and totally remove the battery.
So here we go:
!!!REMOVE ALL THE LG USB DRIVERS FROM THE SYSTEM BEFORE YOU CONTINUE!!! Go to add remove programs, select the LG United entry and then uninstall it.
First install the USB Driver from the link above and wait until it has finished with the setup.
Then run the LGMST. When it starts and it says "Disconnected." then put the battery back to the phone and connect the phone to the computer.
Press ONLY the Power button and wait until something happens. If you see that the phones boots and the LGMST starts it by itself then wait till it stops with all the information gathering stuff.
Then regardless of what the program says of you having an update or not, DON'T START THAT UPDATE!
Click on alt on the keyboard and the from the menus at the top select Customer and then emergency(the last option).
Type in the phones IMEI (located at the box of the phone or on a sticker under the battery) without dashes, just numbers.
Finally click on Check and follow the instructions on the screen.
You should be ready as new after 10-15 minutes with the standard V10B firmware and you should not even lose data.
Tell me if that helped so if it didn't we can still fix it I'm sure
Note: I'm aware that 3.3.0 is the latest USB driver that it ships with the phone but for some reason I had only success to flash the phone using the older 3.2.1
That does not work for our problem, just a blank screen is better than stuck in firmware update mode :s
m33ts4k0z said:
Don't panic, I managed to totally brick my phone today and LG told me to send it back for DOA but I managed to recover it in the end.
My phone wouldn't show anything on the screen, it remained black so I can say your position sounds much better than mine.
What you will need:
USB Drivers - Download from here (Check note)
LG Mobile Support Tool (LGMST) - Download from here
Before you start: Disconnect the phone from the computer and totally remove the battery.
So here we go:
!!!REMOVE ALL THE LG USB DRIVERS FROM THE SYSTEM BEFORE YOU CONTINUE!!! Go to add remove programs, select the LG United entry and then uninstall it.
First install the USB Driver from the link above and wait until it has finished with the setup.
Then run the LGMST. When it starts and it says "Disconnected." then put the battery back to the phone and connect the phone to the computer.
Press ONLY the Power button and wait until something happens. If you see that the phones boots and the LGMST starts it by itself then wait till it stops with all the information gathering stuff.
Then regardless of what the program says of you having an update or not, DON'T START THAT UPDATE!
Click on alt on the keyboard and the from the menus at the top select Customer and then emergency(the last option).
Type in the phones IMEI (located at the box of the phone or on a sticker under the battery) without dashes, just numbers.
Finally click on Check and follow the instructions on the screen.
You should be ready as new after 10-15 minutes with the standard V10B firmware and you should not even lose data.
Tell me if that helped so if it didn't we can still fix it I'm sure
Note: I'm aware that 3.3.0 is the latest USB driver that it ships with the phone but for some reason I had only success to flash the phone using the older 3.2.1
Click to expand...
Click to collapse
I'm afraid that didn't work (I think I'm gonna cry soon)
When I go to the Customer Support option, the last option isn't called Emergency it's called "Recovery Phone" and seems to launch exactly the same thing as it does if I click the big "Start Updating" button. There is no option named Emergency at all. Does that mean my phone isn't/wont/can't boot into Emergency mode?
I don't even hold down the power button for my phone to switch on, the second I insert the battery it boots into Clockwork Recovery. If I power off the phone and connect the USB, I don't get the battery charging animation or anything, the screen just remains completely blank. Then if I press the power button (alone or with anything else) it just boots to Clockwork recovery.
The LG Mobile Support Tool seems to detect the phone in this state, but as I said, when it tries to do the download, I just get an error saying "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update". The version of the Mobile Support Tool that it's installing is 1.5.1.8 after downloading from your provided link, just incase you need to know that. It seems the tool automatically updates itself on every launch.
Someone also seems to have posted the actual ROM in this thread, http://forum.xda-developers.com/showthread.php?t=1155874 would installing this perhaps assist? Is it even possible to install this when my phone wont boot up past the recovery manager? If it is possible can someone perhaps advise me how?
__________
P_U_A_John said:
Try the following thread http://forum.xda-developers.com/showthread.php?p=15782541#post15782541
Click to expand...
Click to collapse
Unfortunately the phone wont boot into Emergency mode. The clockwork Recovery mod seems to have taken over all of the boot options. If I hold the volume up key and press the power button, nothing happens. If I hold the volume down key and the power button, it boots to clockwork recovery. If I just press power, boots to clockwork recovery.
Is there any way to strip off Clockwork recovery and restore the original/stock recovery onto the phone? Or even just remove Clockwork recovery so that it just hangs on the LG boot screen? (See reasoning for this below)
I can still select the USB mount option in Clockwork recovery and the PC still picks it up as a storage device and I can browse around.
The phone is only 7 days old, so I'm almost tempted to just delete the internal memory so that clockwork doesn't show up, then take the phone back to the store and say it wont boot up and try to get it replaced.
Or what would happen if I renamed the clockworkmod folder on the phone's hard drive?
(Just another note, I don't have an external SD card in the phone, just the internal memory)
__________
P_U_A_John said:
1)Plug USB cable
2)Hold "POWER+VOL.UP" (Wait logo LG and mobile screen off) 10 seconds !! For Emergency mode!
3)Hold a second time "POWER+VOL.UP" 10 seconds (the mobile is detected by LGMobile update)
The screen is off in this mode.
PS:
I am trying to upload a backup of the rom.
You may be able to restore from the recovery clockwork ... but it must be 4.0.0.9
Click to expand...
Click to collapse
I do have 4.0.0.9 of the ClockworkMod recovery.
I've tried holding the up volume key and then holding the power key, and I do seem to get emergency mode with the LG Mobile update software detects the phone (with no Clockwork Recovery mod showing on screen) however when I try to use the Recovery phone option, I still get the same error "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update"
If you can upload a backup of the ROM and advise on how to install it via Clockwork, you will be my hero.
1)Plug USB cable
2)Hold "POWER+VOL.UP" (Wait logo LG and mobile screen off) 10 seconds !! For Emergency mode!
3)Hold a second time "POWER+VOL.UP" 10 seconds (the mobile is detected by LGMobile update)
The screen is off in this mode.
PS:
I am trying to upload a backup of the rom.
You may be able to restore from the recovery clockwork ... but it must be 4.0.0.9
Click to expand...
Click to collapse
I do have 4.0.0.9 of the ClockworkMod recovery.
I've tried holding the up volume key and then holding the power key, and I do seem to get emergency mode with the LG Mobile update software detects the phone (with no Clockwork Recovery mod showing on screen) however when I try to use the Recovery phone option, I still get the same error "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update"
If you can upload a backup of the ROM and advise on how to install it via Clockwork, you will be my hero.
Click to expand...
Click to collapse
I had the same error "fatal error " your not putting it in recovery mode right I fixed myn
Sent from my LG-P920 using Tapatalk
ik911 said:
I had the same error "fatal error " your not putting it in recovery mode right I fixed myn
Sent from my LG-P920 using Tapatalk
Click to expand...
Click to collapse
How else can I put it into Recovery Mode? How can I tell if I've done it right?
I managed to hold the up volume key and hold down the power button, and the LG Mobile Update detected the phone whilst the screen was blank. I thought that meant I was in recovery mode?
I should point out that the LG Logo wasn't flashing up however. I only ever see the LG Logo before it boots into Clockwork RecoveryMod
I also got that fatal error thing when i bricked my phone. For me the phone would start flashing but it got stuck at 17% and then an error followed saying that there was a communication problem between the phone and the pc. My solution was to switch from my desktop computer to my laptop and the procedure ran smoothly after.
You said that the phone powers up directly after you connect it to the pc and while having the support tool running?
You can try to shut it down so it shows a black screen as you said and then try to boot into emergency mode with the vol.up+power button.
The windows sounds might help you on that. you can listen from the computer when the phone connects/powers up or not.
EDIT: Just read your post, if the phone remains black is a good thing.
if your update fails or goes into clockwork recovery etc you will need LG mobile update on your pc and install the lg p920 drivers
turn your phone off take the battery out leave it for 10 sec, connect battery and usb cable hold power and volume up hold it for 10 sec let go then do it again for 10 sec
now run LG mobile update click customer support > recover type your imei let it update once finished power up phone now you will get a screen on the phone that says updating let it update
Well I'm not sure what I did differently. Not sure if I wasn't pressing the button hard enough or my finger was slipping off, or if I've just somehow tricked the phone, but the LG Phone Update from the Phone Recovery option is now running.
I've been doing the same thing I was doing before (or at least thought I was doing) and I'm not sure what I did differently....but....fingers crossed..... the download will finish in 40 minutes (on a crappy connection at the moment) so I'll be able to see what happens then....
UPDATE -
Progress, though not quite yet success.
The LG Mobile Support tool downloaded the software and applied the update succesfully, though my phone didn't automatically restart. I pressed the power button however and it loaded up and not into Clockwork Recovery Mod. It's not however sitting on an "Updating Firmware" screen and the progress bar doesn't seem to be filling at all.
How long does this part of the process normally take?
Does the phone need to be connected to USB for this part of the process? The LG Mobile Support Tool says the phone is disconnected so I'm guessing there's no active data connection between the PC and phone, just power.
Does this normally take a while? Or should I perhaps try the recovery again?
Lagamorph said:
Well I'm not sure what I did differently. Not sure if I wasn't pressing the button hard enough or my finger was slipping off, or if I've just somehow tricked the phone, but the LG Phone Update from the Phone Recovery option is now running.
I've been doing the same thing I was doing before (or at least thought I was doing) and I'm not sure what I did differently....but....fingers crossed..... the download will finish in 40 minutes (on a crappy connection at the moment) so I'll be able to see what happens then....
UPDATE -
Progress, though not quite yet success.
The LG Mobile Support tool downloaded the software and applied the update succesfully, though my phone didn't automatically restart. I pressed the power button however and it loaded up and not into Clockwork Recovery Mod. It's not however sitting on an "Updating Firmware" screen and the progress bar doesn't seem to be filling at all.
How long does this part of the process normally take?
Does the phone need to be connected to USB for this part of the process? The LG Mobile Support Tool says the phone is disconnected so I'm guessing there's no active data connection between the PC and phone, just power.
Does this normally take a while? Or should I perhaps try the recovery again?
Click to expand...
Click to collapse
This is only supposed to happen when you apply the OTA update. Try to reapply the stock firmware in emergency mode. After the program applies the firmware, it should boot up the phone by itself in android and give you a success or finish message on the computer.
m33ts4k0z said:
This is only supposed to happen when you apply the OTA update. Try to reapply the stock firmware in emergency mode. After the program applies the firmware, it should boot up the phone by itself in android and give you a success or finish message on the computer.
Click to expand...
Click to collapse
Is applying the Stock Firmware not what I did with the LG Mobile Support Tool when it downloaded that huge 300MB+ file?
I have contacted the customer services for Carphone Warehouse, and the guy advised that if the phone seemed to have developed a fault and wouldn't start, then since it's within 28 days of purcahse I can get a like for like replacement. Might have to go ahead and do that this evening.
Hi, i'm a user of the Optimus 4X and i was attempting to install CWM recovery on my phone using ROM Manager (i was rooted with the stock ROM and a locked bootloader), after the process was finished i booted into recovery mode and got an error in boot image signature and the phone powered off in 5 seconds. I was still able to use my phone normally so i used the APK method to install CWM and fix the issue, but after the process is done now i got the same error, i'm stuck in a boot loop when trying to access the phone, and i can't get into S/W mode. With the LG logo i can tell it's not a hard brick, but anyone could help me about that, please?
Okay problem solved. For anyone who might have this problem, i tried to enter S/W mode while battery is inserted in the mobile, that means battery in, hold volume - button, plug in USB. The phone went to S/W mode and i used LG mobile support tool to recover my phone.
Hey,
I'm trying to root my T-Mobile LG G2 with stock 4.4.2, but the it just refuses to enter download mode. I've tried the standard method of entering download mode (powering down the phone, holding down the volume button, plugging in the USB cable from my computer), but only the LG logo appears on screen, then the battery percentage appears on screen, and then the phone begins to charge. I've tried using different USB cables and different PCs, but nothing seems to work.
Is there anything I'm doing wrong here? Any extra steps that need to be taken?
Any help would be greatly appreciated!
Try holding up and power and let go of power when the logo shows then push the and hold power again.
alil2cul4u said:
Try holding up and power and let go of power when the logo shows then push the and hold power again.
Click to expand...
Click to collapse
Do you mean hold power and volume up, plug phone in, let go of power and keep holding volume up, and then hold power and volume up again? I tried that, and the LG logo splashes on screen, disappears, splashes again, and then the screen goes black and the LED notification light blinks red. It doesn't pulse, like when it's charging, but it blinks a steady beat. It stops blinking and the phone boots up when I let go of the power and volume up buttons...
STAR8UCK said:
Do you mean hold power and volume up, plug phone in, let go of power and keep holding volume up, and then hold power and volume up again? I tried that, and the LG logo splashes on screen, disappears, splashes again, and then the screen goes black and the LED notification light blinks red. It doesn't pulse, like when it's charging, but it blinks a steady beat. It stops blinking and the phone boots up when I let go of the power and volume up buttons...
Click to expand...
Click to collapse
When I went into download mode, I only held the Volume Up button and plugged in the USB to the pc. I didn't hold power.
Same problem here ! Recieved d802 v20f OTA and after the update my phones refuses to entering download mode.
STAR8UCK said:
Hey,
I'm trying to root my T-Mobile LG G2 with stock 4.4.2, but the it just refuses to enter download mode. I've tried the standard method of entering download mode (powering down the phone, holding down the volume button, plugging in the USB cable from my computer), but only the LG logo appears on screen, then the battery percentage appears on screen, and then the phone begins to charge. I've tried using different USB cables and different PCs, but nothing seems to work.
Is there anything I'm doing wrong here? Any extra steps that need to be taken?
Any help would be greatly appreciated!
Click to expand...
Click to collapse
head1shot said:
Same problem here ! Recieved d802 v20f OTA and after the update my phones refuses to entering download mode.
Click to expand...
Click to collapse
I'm on rooted 20e with custom recovery and I entered download mode no problem. Make sure you're pressing only the Volume Up button when plugging in the USB connected to the computer and hold it until you enter download mode.
did anyone ever get it to go into download mode , I'm trying to get into download mode on my wifes phone to flask 4.2.2 so I can root
Damented said:
did anyone ever get it to go into download mode , I'm trying to get into download mode on my wifes phone to flask 4.2.2 so I can root
Click to expand...
Click to collapse
I'm having the same problem with my LG G2, I can't get into download mode. I've tried holding the power up button and plugging in a USB cable but my phone shows the LG logo and then starts charging the battery, I'm on stock rom, 4.4.2, no custom recovery. Is there a fix for this?
I had a similar problem with my T-Mobile LG G2 where I was rooted and accepted an OTA. It broke root and I couldn't get IOroot or Stumproot to work. Went to flash a downgrade and found the phone wouldn't go into download mode. It was NOT bricked. I finally tried playing around with the LG Mobile Support Tool (B2CAppSetup.exe). Of course it detected that my phone already had the latest firmware from T-Mobile, but then I clicked Options>Upgrade Recovery.
It downloaded for a while then I noticed it had put my phone into download mode (it said "Rooted" in red letters at the bottom). Then it flashed the same firmware over and I immediately tested, it entered download mode right away. But I didn't end up needing that as Stumproot was able to brute force it now after the recovery flash.
Anyway, I couldn't find an answer anywhere else. Most results also have a bricked phone, but that wasn't my issue. This solved my problem and maybe it could work for others.
ratchet26 said:
I had a similar problem with my T-Mobile LG G2 where I was rooted and accepted an OTA. It broke root and I couldn't get IOroot or Stumproot to work. Went to flash a downgrade and found the phone wouldn't go into download mode. It was NOT bricked. I finally tried playing around with the LG Mobile Support Tool (B2CAppSetup.exe). Of course it detected that my phone already had the latest firmware from T-Mobile, but then I clicked Options>Upgrade Recovery.
It downloaded for a while then I noticed it had put my phone into download mode (it said "Rooted" in red letters at the bottom). Then it flashed the same firmware over and I immediately tested, it entered download mode right away. But I didn't end up needing that as Stumproot was able to brute force it now after the recovery flash.
Anyway, I couldn't find an answer anywhere else. Most results also have a bricked phone, but that wasn't my issue. This solved my problem and maybe it could work for others.
Click to expand...
Click to collapse
This was my exact problem! Your solution worked perfectly, I was beating my head against the wall trying to find a way around.
Thanks so much !
ratchet26 said:
I had a similar problem with my T-Mobile LG G2 where I was rooted and accepted an OTA. It broke root and I couldn't get IOroot or Stumproot to work. Went to flash a downgrade and found the phone wouldn't go into download mode. It was NOT bricked. I finally tried playing around with the LG Mobile Support Tool (B2CAppSetup.exe). Of course it detected that my phone already had the latest firmware from T-Mobile, but then I clicked Options>Upgrade Recovery.
It downloaded for a while then I noticed it had put my phone into download mode (it said "Rooted" in red letters at the bottom). Then it flashed the same firmware over and I immediately tested, it entered download mode right away. But I didn't end up needing that as Stumproot was able to brute force it now after the recovery flash.
Anyway, I couldn't find an answer anywhere else. Most results also have a bricked phone, but that wasn't my issue. This solved my problem and maybe it could work for others.
Click to expand...
Click to collapse
Aaaaaaaahhh!!! u are my hero man!, ive been searching everywere and tried everything, im quite new to lg mobile phones, ive used apple and samsung before, but this easy and simple method worked for me, finally ive entered download mode again! :good:
I tried but mine says no problems to fix or somethibg like that
Sent from my LG-D801 using XDA Free mobile app
Thank you! I was pulling my hair out too! Out of desperation I took the g20 update after my phone had gotten real unsteady and rebooting constantly. Like the op I lost root and couldn't get into dl mode to save my life.
Sent from my LG-D801 using XDA Free mobile app
i still cant go to download mode...i tried all above... :crying:
ratchet26 said:
I had a similar problem with my T-Mobile LG G2 where I was rooted and accepted an OTA. It broke root and I couldn't get IOroot or Stumproot to work. Went to flash a downgrade and found the phone wouldn't go into download mode. It was NOT bricked. I finally tried playing around with the LG Mobile Support Tool (B2CAppSetup.exe). Of course it detected that my phone already had the latest firmware from T-Mobile, but then I clicked Options>Upgrade Recovery.
It downloaded for a while then I noticed it had put my phone into download mode (it said "Rooted" in red letters at the bottom). Then it flashed the same firmware over and I immediately tested, it entered download mode right away. But I didn't end up needing that as Stumproot was able to brute force it now after the recovery flash.
Anyway, I couldn't find an answer anywhere else. Most results also have a bricked phone, but that wasn't my issue. This solved my problem and maybe it could work for others.
Click to expand...
Click to collapse
After clicking Options>Upgrade Recovery it said "No upgrade items to fix." Thank you all for what you do at XDA.
verizonwiz said:
After clicking Options>Upgrade Recovery it said "No upgrade items to fix." Thank you all for what you do at XDA.
Click to expand...
Click to collapse
So this program no longer works and I'm having the same problem. I tried to do this with the LG suit which replaced lg mobile support. It just keeps saying I'm already on the latest firmware. Can anyone help?
Please guys I need your help!
Phone model: Lg G Stylo h631 T-Mobile version.
Today I was using my phone and after finishing a call, my phone started to update itself. Then I received a error message. After that, I get stuck with a dead android guy on the screen, and I get the message "no command". I try Different combinations of buttons to solve this problem: Volume Down + Power release and then press the buttons again went the LG logo appear and have no luck. Then I try Volume Up + Power, also have no luck. I think I try almost every possible combination an nothing is working.
If anyone has any idea how to solve this issue please help me. Any help would be appreciated.
(Sorry for my bad English)
Make sure you download or have downloaded and installed the LG drivers from the LG website or any other reliable source or your phone will not be able to recover.
Unplug the phone, take out the battery and once the phone is completely off, replace the battery. Keep the phone powered off and unplugged. Plug a data capable (the usb that came with the phone is best) usb into a PC. Press the VOLUME UP button and HOLD it WHILE plugging the usb into your phone, (The PC should already be connected before plugging in the phone) continue to hold the VOLUME UP button until you pass the LG splash screen and you should then be in DOWNLOAD MODE. From there you can reflash the stock ROM that came with the phone. The stock ROMs are pretty easy to find here on XDA.
If you don't know what flashing a ROM is or means then XDA has plenty of guides for that as well. To return to stock you will need the LG Flash Tool or LG UP depending on which version you want to flash. Marshmalllow uses the LG UP program and Lollipop uses the LG Flash Tool. You can find guides and all the tools\software you will need to fix your phone right here on XDA or a little Google searching.
My phone is stuck on this screen and keeps restarting by their own.
I even tried to press power button but the bootloader warning is still can't removed.
I till tried to press the V-/PB and V+/PB and V+-/PB but it didn't work.
When I tried to connect my phone to my PC but my PC can't detect my phone...
I was trying to install the TWRP recovery image to install the TWRP recovery in Odin.
Can you help me by not, to waste my time and don't tell me to head my phone to the nearest service center.
So I can use my phone for generally.
Have you tried holding V-/PB then when the screen goes black connect it to a charger and hold V-+/PB