Oh dear.....I hope I haven't destroyed my O3D....
I was attempting to install the V10D update, so used the backup I took right after rooting and installing ROM Manager to restore the phone to its status before installing the performance pack. If I tried installing the update OTA before this I just got an invalid package error.
So the restore went well and it rebooted fine. So I ran the update again, and it downloaded and appeared to install, but when the phone rebooted it just booted straight into the recovery. I tried to get it to reboot again, but again it just booted back into recovery.
Ok, nothing to worry about I thought, I just ran the restore again with the same restore point as before....but after it finished it's still booting back up into the recovery!!! No matter what I do the phone just seems to keep booting into the recovery menu. I've tried booting into emergency mode by powering the phone off, then holding the UP Volume key and holding power, but it doesn't seem to work.
Can anyone help? Please?
Lil update -
When powering off the phone and then connecting it to the USB cable, it automatically boots into recovery mode without me even touching the power button. At this point the LG Mobile Update detects the phone and advises me that there's an update available. I try to apply this, but after entering the SN and IMEI, it just gives me a message "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update". I get the same error if I use the recovery Phone option. This always happens at the download stage, so is it possible that it's just failing to download the update from LG rather than actually do anything with the phone?
Please don't tell me I've ruined my brand new phone!!
Unfortunatly, you've managed to do the same as I have... leave the phone for e a few days and wait for a rom that you can install via clockwork recovery, you'll have your phone up and running again. Dont do as I did and wipe the recovery from the phone, it will result in a total brick (or at least a brick till LG releaase a full rom update (could be months yet...).
Oh man, I'm panicking so much that I might have ruined the phone now.....
read this thread for more info... http://forum.xda-developers.com/showthread.php?p=15762389#post15762389
madshaun1984 said:
read this thread for more info... http://forum.xda-developers.com/showthread.php?p=15762389#post15762389
Click to expand...
Click to collapse
I'm not sure what I'm looking for there, I've looked through that thread but it doesn't seem relevant to the problem I'm having.
I have the same problem, if you put it into emergency mode you can update to 10d but then its even worse then you are stuck in the firmware update screen
tomorrow I leave on holiday and was planning for nice 3d pictures and movies but I am screwed...
Lagamorph said:
Oh dear.....I hope I haven't destroyed my O3D....
I was attempting to install the V10D update, so used the backup I took right after rooting and installing ROM Manager to restore the phone to its status before installing the performance pack. If I tried installing the update OTA before this I just got an invalid package error.
So the restore went well and it rebooted fine. So I ran the update again, and it downloaded and appeared to install, but when the phone rebooted it just booted straight into the recovery. I tried to get it to reboot again, but again it just booted back into recovery.
Ok, nothing to worry about I thought, I just ran the restore again with the same restore point as before....but after it finished it's still booting back up into the recovery!!! No matter what I do the phone just seems to keep booting into the recovery menu. I've tried booting into emergency mode by powering the phone off, then holding the UP Volume key and holding power, but it doesn't seem to work.
Can anyone help? Please?
Lil update -
When powering off the phone and then connecting it to the USB cable, it automatically boots into recovery mode without me even touching the power button. At this point the LG Mobile Update detects the phone and advises me that there's an update available. I try to apply this, but after entering the SN and IMEI, it just gives me a message "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update". I get the same error if I use the recovery Phone option. This always happens at the download stage, so is it possible that it's just failing to download the update from LG rather than actually do anything with the phone?
Please don't tell me I've ruined my brand new phone!!
Click to expand...
Click to collapse
Don't panic, I managed to totally brick my phone today and LG told me to send it back for DOA but I managed to recover it in the end.
My phone wouldn't show anything on the screen, it remained black so I can say your position sounds much better than mine.
What you will need:
USB Drivers - Download from here (Check note)
LG Mobile Support Tool (LGMST) - Download from here
Before you start: Disconnect the phone from the computer and totally remove the battery.
So here we go:
!!!REMOVE ALL THE LG USB DRIVERS FROM THE SYSTEM BEFORE YOU CONTINUE!!! Go to add remove programs, select the LG United entry and then uninstall it.
First install the USB Driver from the link above and wait until it has finished with the setup.
Then run the LGMST. When it starts and it says "Disconnected." then put the battery back to the phone and connect the phone to the computer.
Press ONLY the Power button and wait until something happens. If you see that the phones boots and the LGMST starts it by itself then wait till it stops with all the information gathering stuff.
Then regardless of what the program says of you having an update or not, DON'T START THAT UPDATE!
Click on alt on the keyboard and the from the menus at the top select Customer and then emergency(the last option).
Type in the phones IMEI (located at the box of the phone or on a sticker under the battery) without dashes, just numbers.
Finally click on Check and follow the instructions on the screen.
You should be ready as new after 10-15 minutes with the standard V10B firmware and you should not even lose data.
Tell me if that helped so if it didn't we can still fix it I'm sure
Note: I'm aware that 3.3.0 is the latest USB driver that it ships with the phone but for some reason I had only success to flash the phone using the older 3.2.1
That does not work for our problem, just a blank screen is better than stuck in firmware update mode :s
m33ts4k0z said:
Don't panic, I managed to totally brick my phone today and LG told me to send it back for DOA but I managed to recover it in the end.
My phone wouldn't show anything on the screen, it remained black so I can say your position sounds much better than mine.
What you will need:
USB Drivers - Download from here (Check note)
LG Mobile Support Tool (LGMST) - Download from here
Before you start: Disconnect the phone from the computer and totally remove the battery.
So here we go:
!!!REMOVE ALL THE LG USB DRIVERS FROM THE SYSTEM BEFORE YOU CONTINUE!!! Go to add remove programs, select the LG United entry and then uninstall it.
First install the USB Driver from the link above and wait until it has finished with the setup.
Then run the LGMST. When it starts and it says "Disconnected." then put the battery back to the phone and connect the phone to the computer.
Press ONLY the Power button and wait until something happens. If you see that the phones boots and the LGMST starts it by itself then wait till it stops with all the information gathering stuff.
Then regardless of what the program says of you having an update or not, DON'T START THAT UPDATE!
Click on alt on the keyboard and the from the menus at the top select Customer and then emergency(the last option).
Type in the phones IMEI (located at the box of the phone or on a sticker under the battery) without dashes, just numbers.
Finally click on Check and follow the instructions on the screen.
You should be ready as new after 10-15 minutes with the standard V10B firmware and you should not even lose data.
Tell me if that helped so if it didn't we can still fix it I'm sure
Note: I'm aware that 3.3.0 is the latest USB driver that it ships with the phone but for some reason I had only success to flash the phone using the older 3.2.1
Click to expand...
Click to collapse
I'm afraid that didn't work (I think I'm gonna cry soon)
When I go to the Customer Support option, the last option isn't called Emergency it's called "Recovery Phone" and seems to launch exactly the same thing as it does if I click the big "Start Updating" button. There is no option named Emergency at all. Does that mean my phone isn't/wont/can't boot into Emergency mode?
I don't even hold down the power button for my phone to switch on, the second I insert the battery it boots into Clockwork Recovery. If I power off the phone and connect the USB, I don't get the battery charging animation or anything, the screen just remains completely blank. Then if I press the power button (alone or with anything else) it just boots to Clockwork recovery.
The LG Mobile Support Tool seems to detect the phone in this state, but as I said, when it tries to do the download, I just get an error saying "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update". The version of the Mobile Support Tool that it's installing is 1.5.1.8 after downloading from your provided link, just incase you need to know that. It seems the tool automatically updates itself on every launch.
Someone also seems to have posted the actual ROM in this thread, http://forum.xda-developers.com/showthread.php?t=1155874 would installing this perhaps assist? Is it even possible to install this when my phone wont boot up past the recovery manager? If it is possible can someone perhaps advise me how?
__________
P_U_A_John said:
Try the following thread http://forum.xda-developers.com/showthread.php?p=15782541#post15782541
Click to expand...
Click to collapse
Unfortunately the phone wont boot into Emergency mode. The clockwork Recovery mod seems to have taken over all of the boot options. If I hold the volume up key and press the power button, nothing happens. If I hold the volume down key and the power button, it boots to clockwork recovery. If I just press power, boots to clockwork recovery.
Is there any way to strip off Clockwork recovery and restore the original/stock recovery onto the phone? Or even just remove Clockwork recovery so that it just hangs on the LG boot screen? (See reasoning for this below)
I can still select the USB mount option in Clockwork recovery and the PC still picks it up as a storage device and I can browse around.
The phone is only 7 days old, so I'm almost tempted to just delete the internal memory so that clockwork doesn't show up, then take the phone back to the store and say it wont boot up and try to get it replaced.
Or what would happen if I renamed the clockworkmod folder on the phone's hard drive?
(Just another note, I don't have an external SD card in the phone, just the internal memory)
__________
P_U_A_John said:
1)Plug USB cable
2)Hold "POWER+VOL.UP" (Wait logo LG and mobile screen off) 10 seconds !! For Emergency mode!
3)Hold a second time "POWER+VOL.UP" 10 seconds (the mobile is detected by LGMobile update)
The screen is off in this mode.
PS:
I am trying to upload a backup of the rom.
You may be able to restore from the recovery clockwork ... but it must be 4.0.0.9
Click to expand...
Click to collapse
I do have 4.0.0.9 of the ClockworkMod recovery.
I've tried holding the up volume key and then holding the power key, and I do seem to get emergency mode with the LG Mobile update software detects the phone (with no Clockwork Recovery mod showing on screen) however when I try to use the Recovery phone option, I still get the same error "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update"
If you can upload a backup of the ROM and advise on how to install it via Clockwork, you will be my hero.
1)Plug USB cable
2)Hold "POWER+VOL.UP" (Wait logo LG and mobile screen off) 10 seconds !! For Emergency mode!
3)Hold a second time "POWER+VOL.UP" 10 seconds (the mobile is detected by LGMobile update)
The screen is off in this mode.
PS:
I am trying to upload a backup of the rom.
You may be able to restore from the recovery clockwork ... but it must be 4.0.0.9
Click to expand...
Click to collapse
I do have 4.0.0.9 of the ClockworkMod recovery.
I've tried holding the up volume key and then holding the power key, and I do seem to get emergency mode with the LG Mobile update software detects the phone (with no Clockwork Recovery mod showing on screen) however when I try to use the Recovery phone option, I still get the same error "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update"
If you can upload a backup of the ROM and advise on how to install it via Clockwork, you will be my hero.
Click to expand...
Click to collapse
I had the same error "fatal error " your not putting it in recovery mode right I fixed myn
Sent from my LG-P920 using Tapatalk
ik911 said:
I had the same error "fatal error " your not putting it in recovery mode right I fixed myn
Sent from my LG-P920 using Tapatalk
Click to expand...
Click to collapse
How else can I put it into Recovery Mode? How can I tell if I've done it right?
I managed to hold the up volume key and hold down the power button, and the LG Mobile Update detected the phone whilst the screen was blank. I thought that meant I was in recovery mode?
I should point out that the LG Logo wasn't flashing up however. I only ever see the LG Logo before it boots into Clockwork RecoveryMod
I also got that fatal error thing when i bricked my phone. For me the phone would start flashing but it got stuck at 17% and then an error followed saying that there was a communication problem between the phone and the pc. My solution was to switch from my desktop computer to my laptop and the procedure ran smoothly after.
You said that the phone powers up directly after you connect it to the pc and while having the support tool running?
You can try to shut it down so it shows a black screen as you said and then try to boot into emergency mode with the vol.up+power button.
The windows sounds might help you on that. you can listen from the computer when the phone connects/powers up or not.
EDIT: Just read your post, if the phone remains black is a good thing.
if your update fails or goes into clockwork recovery etc you will need LG mobile update on your pc and install the lg p920 drivers
turn your phone off take the battery out leave it for 10 sec, connect battery and usb cable hold power and volume up hold it for 10 sec let go then do it again for 10 sec
now run LG mobile update click customer support > recover type your imei let it update once finished power up phone now you will get a screen on the phone that says updating let it update
Well I'm not sure what I did differently. Not sure if I wasn't pressing the button hard enough or my finger was slipping off, or if I've just somehow tricked the phone, but the LG Phone Update from the Phone Recovery option is now running.
I've been doing the same thing I was doing before (or at least thought I was doing) and I'm not sure what I did differently....but....fingers crossed..... the download will finish in 40 minutes (on a crappy connection at the moment) so I'll be able to see what happens then....
UPDATE -
Progress, though not quite yet success.
The LG Mobile Support tool downloaded the software and applied the update succesfully, though my phone didn't automatically restart. I pressed the power button however and it loaded up and not into Clockwork Recovery Mod. It's not however sitting on an "Updating Firmware" screen and the progress bar doesn't seem to be filling at all.
How long does this part of the process normally take?
Does the phone need to be connected to USB for this part of the process? The LG Mobile Support Tool says the phone is disconnected so I'm guessing there's no active data connection between the PC and phone, just power.
Does this normally take a while? Or should I perhaps try the recovery again?
Lagamorph said:
Well I'm not sure what I did differently. Not sure if I wasn't pressing the button hard enough or my finger was slipping off, or if I've just somehow tricked the phone, but the LG Phone Update from the Phone Recovery option is now running.
I've been doing the same thing I was doing before (or at least thought I was doing) and I'm not sure what I did differently....but....fingers crossed..... the download will finish in 40 minutes (on a crappy connection at the moment) so I'll be able to see what happens then....
UPDATE -
Progress, though not quite yet success.
The LG Mobile Support tool downloaded the software and applied the update succesfully, though my phone didn't automatically restart. I pressed the power button however and it loaded up and not into Clockwork Recovery Mod. It's not however sitting on an "Updating Firmware" screen and the progress bar doesn't seem to be filling at all.
How long does this part of the process normally take?
Does the phone need to be connected to USB for this part of the process? The LG Mobile Support Tool says the phone is disconnected so I'm guessing there's no active data connection between the PC and phone, just power.
Does this normally take a while? Or should I perhaps try the recovery again?
Click to expand...
Click to collapse
This is only supposed to happen when you apply the OTA update. Try to reapply the stock firmware in emergency mode. After the program applies the firmware, it should boot up the phone by itself in android and give you a success or finish message on the computer.
m33ts4k0z said:
This is only supposed to happen when you apply the OTA update. Try to reapply the stock firmware in emergency mode. After the program applies the firmware, it should boot up the phone by itself in android and give you a success or finish message on the computer.
Click to expand...
Click to collapse
Is applying the Stock Firmware not what I did with the LG Mobile Support Tool when it downloaded that huge 300MB+ file?
I have contacted the customer services for Carphone Warehouse, and the guy advised that if the phone seemed to have developed a fault and wouldn't start, then since it's within 28 days of purcahse I can get a like for like replacement. Might have to go ahead and do that this evening.
Related
My phone is currently sitting with a "S/W upgrade" screen after a series of stupid events. I flashed recovery using ROM Manager before I had read that it fake flashed. I rebooted into recovery and installed CM7 nightly. Rebooted and it's stuck in a boot loop. So I finally see all the warnings against that so I figure I need to get a real recovery so I use the awesome guide from TGA_Gunnman. I follow all the instructions and it appears from the log on my PC that the CM recovery flashed successfully. I pull the cord, reinsert my battery and my phone just sits in the S/W upgrade screen. It's been like that for 30 minutes now.
What do I do?
I thought I'd done something wrong with my G2x because that happened to me too. Remove your battery and USB. Then insert your battery again. When you turn it on, make sure to hold both the power button and the volume down button until you see text that says android. If you, like me, thought you just had to hold the volume down and tap the power button (like my Nexus One), that might be your issue.
Sent from my Nexus One using Tapatalk
just disconnect usb, and go to recovery Power+vol down...
.....and congrats !
yep, I thought I bricked it too.. When you were done at the green screen where it said press any button, thats where you press whatever you want and then unplug the cord. Then, put the battery back in and hold down vol then power, don't let go until "android" pops up.. You did it man, just missing your last step..
Moved to proper forum
I can get to the Recovery screen, but I cant select any of the options....volume lets me scroll, but cant find anything to select any of the options....kinda new at this
power button to 'action' your selection... at least it works for me.
usajlh said:
My phone is currently sitting with a "S/W upgrade" screen after a series of stupid events. I flashed recovery using ROM Manager before I had read that it fake flashed. I rebooted into recovery and installed CM7 nightly. Rebooted and it's stuck in a boot loop. So I finally see all the warnings against that so I figure I need to get a real recovery so I use the awesome guide from TGA_Gunnman. I follow all the instructions and it appears from the log on my PC that the CM recovery flashed successfully. I pull the cord, reinsert my battery and my phone just sits in the S/W upgrade screen. It's been like that for 30 minutes now.
What do I do?
Click to expand...
Click to collapse
The "S/W upgrade" stays on, that's normal. See if your terminal window has completed whatever stuff it is doing. If you get a completed message, you are good to go and can safely pull out the USB chord even if your phone still says "S/W upgrade". Put back your battery and hold Power+Vol DOWN button and see if you get into cmw recovery.
so im trying to fix my friends phone and this is weird..
im able to go to cwm, wipe it all and flash a new rom.. it flashess successfully but when i reboot it goes back to the s/w update screen..it happens with any rom i flash.. its been sitting there for a while.. how long should i wait?
Once you flash the ROM you shouldn't be getting that screen...Does your friend has the G2x or 2x and which ROM did you flash?
Sounds like you screwed up the boot image. Go into APX mode again and reflash the recovery package making sure it completes, you hit a key to close the terminal window, and you hold the volume buttons the entire time. Then go into recovery and factory reset and clear the Dalvik cache. Then if you still get the S/W update screen you are going to need to go to the thread about fixing bricked phones and use the KDZ method to reflash the entire GB OTA package. There is also a new method to reinstall the entire OTA package using NVFlash but you have to hold the volume buttons down for about ten to fifteen minutes while everything flashes.
Hi
Can anyone help please? Also, are there anyone having similar issue.
Issue: Pressing the power button is not starting my device. In order to power on I have to connect charger (not usb with PC) and then press power button. What I have noticed is that once I switch off my phone it gets in to "emergency/recover mode". I came to this conclusion because after I switch the phone off, take battery out and put back in and then connect usb cable with my PC. I can see OMAP driver loads and also in the PC's Device Manager I am able to see LG CDMA.... under "ports".
It was not like this until i started several attempts to flash baseband.
Sequence of actions
Here is the sequence of actions I went through and end up having my phone at this stage
1. Followed the procedure (http://forum.xda-developers.com/showpost.php?p=17177547&postcount=2) step by step using LG flash tool. The application was constantly crashing (PC is running on XP pro). Before flashing baseband I flashed GB hence I lost radio.
2. To bring back my radio I had to reflash 2.2 following the same procedure (emergency recovery method) in the link given in baseband flashing.
3. After finishing the recovery flash I could not start my phone using power button. I started thinking that I bricked my phone. I left it for a day. Then I thought that the battery is fully drained and is the reason for not powering on. When I connected charger I started seeing LG logo and also the phone was started. I was more excited and happy that my phone was not bricked. After this point I need charger connected everytime when i want switch on my phone. so, I am scared to swtich off my phone unless I have charger handy to me.
4. I removed all the application (LG flashing related) including LG drivers I installed before. Now I reinstalled all the necessary app and drivers for baseband flashing. This time baseband flashing was done successfully (though at 22%). Then I flashed GB rom and everything works fine.
The only issue i have is, I can not switch on my phone without charger connected.
If anyone knows solution please help me.
Thanks in advance.
http://forum.xda-developers.com/showthread.php?t=1331390
I used to have the same problem,
I think its a problem about boot,
when I use lg tools it always gives error, because phone wont boot without charger, so it cant continue upgrading
I try flasing original kdz file from lg flash tool, and use emergency rescue mode,
I dont know but it somehow repair the boot
you can fix permissions before you use lg tools.
what error do you have while using lg tool?
can you post the screen capture
nurikarakaya said:
http://forum.xda-developers.com/showthread.php?t=1331390
I used to have the same problem,
I think its a problem about boot,
when I use lg tools it always gives error, because phone wont boot without charger, so it cant continue upgrading
I try flasing original kdz file from lg flash tool, and use emergency rescue mode,
I dont know but it somehow repair the boot
you can fix permissions before you use lg tools.
what error do you have while using lg tool?
can you post the screen capture
Click to expand...
Click to collapse
After i uninstalled all the drivers (incl. LG tools) and reinstalled and I am not seeing any more error while using LG tools. I even flashed GB baseband twice but no use. The link you have given explains the same issue I have.
I think you have to install froyo version of baseband and firmware first,
then try
http://forum.xda-developers.com/showthread.php?t=1186406
STUCK AT LG LOGO:
with factory reset!
1) Start LG Mobile update
2) Power off your phone without USB cable
3) Connect the USB cable and wait for the LG logo and the annimation battery
4) Pressing Vol.up + power 6-7 seconde wait for the LG logo and The screen turns off
5) Again pressing Vol.up + power 6-7 seconde and wait until the drivers are installed (LG Mobile update detects your phone and the screen is always off)
-If this is the first time the driver install redone the item 5).
6) Click on User/Support then emergency mode, insert your IMEI and click on check
7) Wait for download and upgrading (15/20 min)
Questions or Problems Should Not Be Posted in the Development Forum
Please Post in the Correct Forums and Read THIS
Moving to General
lufc said:
Questions or Problems Should Not Be Posted in the Development Forum
Please Post in the Correct Forums and Read THIS
Moving to General
Click to expand...
Click to collapse
Thanks. will stick to the rule in future..
nurikarakaya said:
I think you have to install froyo version of baseband and firmware first,
then try
http://forum.xda-developers.com/showthread.php?t=1186406
STUCK AT LG LOGO:
with factory reset!
1) Start LG Mobile update
2) Power off your phone without USB cable
3) Connect the USB cable and wait for the LG logo and the annimation battery
4) Pressing Vol.up + power 6-7 seconde wait for the LG logo and The screen turns off
5) Again pressing Vol.up + power 6-7 seconde and wait until the drivers are installed (LG Mobile update detects your phone and the screen is always off)
-If this is the first time the driver install redone the item 5).
6) Click on User/Support then emergency mode, insert your IMEI and click on check
7) Wait for download and upgrading (15/20 min)
Click to expand...
Click to collapse
Thanks. I will try it tonight or will wait for official GB release then i can do the this emergency update.
My phone seems to be stuck in download mode. I'm trying to get it to recovery, all attempts result in it going back to download.
I just don't know how to get something else showing on here.
Background: Phone was rooted on Kitkat but I lost the root when I upgraded to Lollipop.
Was trying to root the phone with via the one click (http://forum.xda-developers.com/lg-g3/general/guide-root-lg-firmwares-kitkat-lollipop-t3056951) which seems simple enough. However, my phone would not enter into download mode so I couldn't continue the steps. I found someone with my exact problem right here on XDA (http://forum.xda-developers.com/showpost.php?p=57125760&postcount=9) and in doing what he did, my phone DID enter into download mode, just got stuck in it.
Edit: In pressing Volume Down and Power off and on (press them, release them, press them, release them, etc) an unknown white screen that reads "Factory Data Reset" and a "yes" and "no" has came up. I don't know if I replaced my CWM recovery with this weird thing, in doing what the XDA poster said?? Even if I press "yes", the download mode screen comes back upon restart.
2nd edit: I did get it working. Left the phone connected to the LGMobile Support Tool while I tried the "Upgrade Recovery" again and after a few tries of that it turned on all by itself. Will try rooting again, hopefully succesfully this time
Hey guys - I hope you're doing well.
I recently got an HTC U12+, but wanted to try using a custom ROM due to all of the bloatware . Unfortunately I think I've ended up bricking my device. Here are some things I've since tried:
- Restoring to the backup I made beforehand in TWRP - restore works without any errors, but then just hangs at the boot screen
- Method 1 from this thread (https://forum.xda-developers.com/u12-plus/how-to/collection-htcu-u12-ruu-firmware-t3794664) - TWRP always says the zip files are corrupted for some reason
- Method 3 from that same thread - this actually worked before, but I tried installing a custom ROM again, somehow messed up again, and now this method no longer works as it just hangs at the "HTC" boot screen for eternity
- Both methods in this thread (https://www.theandroidsoul.com/how-to-install-htc-firmware-ruu-and-zip/) - the first one leads to a "failed remote 99 ru unknown fail terrible mishap" error, and for some reason my PC doesn't see my phone when I try the second despite being able to see it in file manager
- Probably many other methods that I've now forgotten
I know this is a whole lot of information, but I'm in desperate need of some help. I typically like to troubleshoot things myself, but I've been trying to fix this for quite some time now and could definitely use another set of (much more experienced) eyes. I greatly appreciate any help you guys can provide.
Thanks.
Flash RUU with SD card method
Download RUU from here(important:check your CID): https://docs.google.com/spreadsheets/d/1wIRrVQawd5rD-t9VKPQ-SdRK20RcJVZhwD7lhmPIK8w/edit#gid=0
1. rename RUU to 2Q55IMG.zip
2. copy zip in the root of your sd card. - external card / not internal - it will not work
3. reboot to download mode,
4. your device will pick up the zip file and flash it.
5.follow on screen instructions and enjoy your RUU(this method erase all your data)
I'm having an issue with my u12+ where it just continually reboots to a message saying "The boot loader is unlocked and the software integrity cannot be guaranteed. Any data stored on the device maybe available to attackers, do not store sensitive data on this device" and then it shows the white HTC logo that says Powered by Android down the bottom of the screen, it stays like that for about 5 minutes and then reboots and does the same thing over again.
Holding the power down button does nothing, it will not turn off the phone. Holding power and volume down does nothing either. The phone just does this every 6 minutes and reboots and cycle and that's it.
I've tried putting the file 2Q55IMG_IMAGINE_DUGL_O80_SENSE10GP_hTC_Asia_TW_1.53.709.1_Radio_sdm845-000201b-1807311356_release_531499_signed_2_4.zip (renamed to 2Q55IMG.zip) on the root of a 8gb Fat32 formatted SD card, but I just can't get into recovery or download mode.
I've tried holding down all 3 side buttons for minutes, or just the power button, or combination of buttons, they all do nothing to the phone. (it's as tho they are disabled, but sometimes holding a combination of the 3 will make the phone vibrate a little bit, but in no particular time or order)
When the phone is in either state (locked bootloader message or white HTC logo) my Windows 10 PC sees the phone plugged in as a "USB Input Device", not an Android Phone or Android Device. So using ADB or Fastboot commands do not work to it. I've tried to force the driver to the HTC driver but that does not work.
I also tried using the RUU_IMAGINE_UHL_O80_SENSE10GP_NA_Gen_Unlock_1.30.617.2.exe file, but once again it doesn't detect my phone.
Any help would be kindly appreciated.
Cheers!
EDIT: So I was finally able to get into download mode by waiting until the phone done its 6 minute reboot and then holding power down until it vibrated once, then held volume up until it vibrated again, then let go of the power button, I was then able to choose recovery, download etc.
So I managed to get the file 2Q55IMG.zip to install, it said it installed 100% okay. The phone rebooted and now I'm stuck again just at the white HTC logo and Power by Android down the bottom of the screen.
This time the phone is not automatically rebooting itself and no key combinations will make it reboot. I've tried holding them all in certain combinations for periods of time, the phone will not reboot or turn off.
EDIT 2: So maybe I didn't wait long enough after installing the 2Q55IMG.zip file, I finally got the phone to reboot and now I've got a working phone again. happy days :laugh:
whowhatwhen said:
I'm having an issue with my u12+ where it just continually reboots to a message saying "The boot loader is unlocked and the software integrity cannot be guaranteed. Any data stored on the device maybe available to attackers, do not store sensitive data on this device" and then it shows the white HTC logo that says Powered by Android down the bottom of the screen, it stays like that for about 5 minutes and then reboots and does the same thing over again.
Holding the power down button does nothing, it will not turn off the phone. Holding power and volume down does nothing either. The phone just does this every 6 minutes and reboots and cycle and that's it.
I've tried putting the file 2Q55IMG_IMAGINE_DUGL_O80_SENSE10GP_hTC_Asia_TW_1.53.709.1_Radio_sdm845-000201b-1807311356_release_531499_signed_2_4.zip (renamed to 2Q55IMG.zip) on the root of a 8gb Fat32 formatted SD card, but I just can't get into recovery or download mode.
I've tried holding down all 3 side buttons for minutes, or just the power button, or combination of buttons, they all do nothing to the phone. (it's as tho they are disabled, but sometimes holding a combination of the 3 will make the phone vibrate a little bit, but in no particular time or order)
When the phone is in either state (locked bootloader message or white HTC logo) my Windows 10 PC sees the phone plugged in as a "USB Input Device", not an Android Phone or Android Device. So using ADB or Fastboot commands do not work to it. I've tried to force the driver to the HTC driver but that does not work.
I also tried using the RUU_IMAGINE_UHL_O80_SENSE10GP_NA_Gen_Unlock_1.30.617.2.exe file, but once again it doesn't detect my phone.
Any help would be kindly appreciated.
Cheers!
Click to expand...
Click to collapse
with the phone off, turn it on,when you feel first vibration
quick release power key and keep push volume down.
Smartphone should boot in bootloader mode.
can you get into this mode with this guide?
fabrizio b92 said:
with the phone off, turn it on,when you feel first vibration
quick release power key and keep push volume down.
Smartphone should boot in bootloader mode.
can you get into this mode with this guide?
Click to expand...
Click to collapse
Cheer mates, issue sorted. I just updated my comment in my post.
Not sure if I'm game enough again now to try and put LeeDrOiD and Magisk on it.
Ok Guys So I Shouldn't Have Done This But I Used Fastboot To Flash Recovery And I think I Did It Wrong. It Said "ok" And Finished And I Rebooted Phone It Resetted And Then Stuck On The Orange State Bootloader Message. I Do The Recovery Mode And Goes Black And Nothing Is Responsive For a While, Sometimes Longer Than Others. This Happens If I Start Phone Normal Or Try Fastboot Or Download.
Because Of My Mistake I Cannot Connect To Pc Software And Im Not Sure Of What I Can Do. I Feel Like Im Not Going To Like The Answer For This But I Got To Take The Blame For This.
Btw i Have A Samsung galaxy Note 20 Ultra Sm-N986u
I think your phone is hard bricked
so you can't get fastboot using volume up+power or via adb?
rescue from manufacturer site pos or just device not being recognised?
It isn't hard bricked it's just way of Samsung trying to make life of simple people more difficult, people who paid for Samsung phones lots of money.
To sort that screen issues what you can surely do is,
Simply press volup + voldown buttons at the same time, no matter if you're on that orange screen or whatever just press those those two buttons at the same time and keep pressing them while you connect your phone to pc. you will boot into download mode. Then flash stock firmware for your phone. After stock of flashed Reboot and start your phone, go to developer options see if oem unlock option is there if it is then oem unlock it if it is not then go back to settings manually change date to year ago, then go to updates disable auto update, connect to WiFi, and press on update several times untill window shows up saying no updates, then go to developer options you should see oem unlock, unlock it.
Then boot into download mode and make sure you have working copy of recovery.
And make sure you follow instructions of whoever recovery you installed on how to boot into recovery. I have S20 plus and too had troubles with it, and the only working recovery for my phone is twrp customised. To boot into it after flashing recovery from odin auto reboot disabled I pressed voldown and power, USB cable connected, then after screen goes off I changed from voldown to volup while kept pressing power button and cable connected. Orange screen with warning showed up for 5 sec I kept pressing and it bottled to twrp and then I was able to install custom rom beyond rom and while installing in aroma I was able ti choose option to remove orange screen.
That's it.
I ran into the same error. I mistakenly loaded twrp's recovery into userdata instead of ap section. The phone was stuck at the orange screen and nothing was happening whatever i pressed. I waited till the battery to dry out and with 0% battery, i directly connected to pc and was able to get into download mode. Then i flashed stock and everything is now back to normal.
Carl Johnson (Cj) said:
I think your phone is hard bricked
Click to expand...
Click to collapse
Absolutely not