Oh dear.....I hope I haven't destroyed my O3D....
I was attempting to install the V10D update, so used the backup I took right after rooting and installing ROM Manager to restore the phone to its status before installing the performance pack. If I tried installing the update OTA before this I just got an invalid package error.
So the restore went well and it rebooted fine. So I ran the update again, and it downloaded and appeared to install, but when the phone rebooted it just booted straight into the recovery. I tried to get it to reboot again, but again it just booted back into recovery.
Ok, nothing to worry about I thought, I just ran the restore again with the same restore point as before....but after it finished it's still booting back up into the recovery!!! No matter what I do the phone just seems to keep booting into the recovery menu. I've tried booting into emergency mode by powering the phone off, then holding the UP Volume key and holding power, but it doesn't seem to work.
Can anyone help? Please?
Lil update -
When powering off the phone and then connecting it to the USB cable, it automatically boots into recovery mode without me even touching the power button. At this point the LG Mobile Update detects the phone and advises me that there's an update available. I try to apply this, but after entering the SN and IMEI, it just gives me a message "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update". I get the same error if I use the recovery Phone option. This always happens at the download stage, so is it possible that it's just failing to download the update from LG rather than actually do anything with the phone?
Please don't tell me I've ruined my brand new phone!!
Unfortunatly, you've managed to do the same as I have... leave the phone for e a few days and wait for a rom that you can install via clockwork recovery, you'll have your phone up and running again. Dont do as I did and wipe the recovery from the phone, it will result in a total brick (or at least a brick till LG releaase a full rom update (could be months yet...).
Oh man, I'm panicking so much that I might have ruined the phone now.....
read this thread for more info... http://forum.xda-developers.com/showthread.php?p=15762389#post15762389
madshaun1984 said:
read this thread for more info... http://forum.xda-developers.com/showthread.php?p=15762389#post15762389
Click to expand...
Click to collapse
I'm not sure what I'm looking for there, I've looked through that thread but it doesn't seem relevant to the problem I'm having.
I have the same problem, if you put it into emergency mode you can update to 10d but then its even worse then you are stuck in the firmware update screen
tomorrow I leave on holiday and was planning for nice 3d pictures and movies but I am screwed...
Lagamorph said:
Oh dear.....I hope I haven't destroyed my O3D....
I was attempting to install the V10D update, so used the backup I took right after rooting and installing ROM Manager to restore the phone to its status before installing the performance pack. If I tried installing the update OTA before this I just got an invalid package error.
So the restore went well and it rebooted fine. So I ran the update again, and it downloaded and appeared to install, but when the phone rebooted it just booted straight into the recovery. I tried to get it to reboot again, but again it just booted back into recovery.
Ok, nothing to worry about I thought, I just ran the restore again with the same restore point as before....but after it finished it's still booting back up into the recovery!!! No matter what I do the phone just seems to keep booting into the recovery menu. I've tried booting into emergency mode by powering the phone off, then holding the UP Volume key and holding power, but it doesn't seem to work.
Can anyone help? Please?
Lil update -
When powering off the phone and then connecting it to the USB cable, it automatically boots into recovery mode without me even touching the power button. At this point the LG Mobile Update detects the phone and advises me that there's an update available. I try to apply this, but after entering the SN and IMEI, it just gives me a message "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update". I get the same error if I use the recovery Phone option. This always happens at the download stage, so is it possible that it's just failing to download the update from LG rather than actually do anything with the phone?
Please don't tell me I've ruined my brand new phone!!
Click to expand...
Click to collapse
Don't panic, I managed to totally brick my phone today and LG told me to send it back for DOA but I managed to recover it in the end.
My phone wouldn't show anything on the screen, it remained black so I can say your position sounds much better than mine.
What you will need:
USB Drivers - Download from here (Check note)
LG Mobile Support Tool (LGMST) - Download from here
Before you start: Disconnect the phone from the computer and totally remove the battery.
So here we go:
!!!REMOVE ALL THE LG USB DRIVERS FROM THE SYSTEM BEFORE YOU CONTINUE!!! Go to add remove programs, select the LG United entry and then uninstall it.
First install the USB Driver from the link above and wait until it has finished with the setup.
Then run the LGMST. When it starts and it says "Disconnected." then put the battery back to the phone and connect the phone to the computer.
Press ONLY the Power button and wait until something happens. If you see that the phones boots and the LGMST starts it by itself then wait till it stops with all the information gathering stuff.
Then regardless of what the program says of you having an update or not, DON'T START THAT UPDATE!
Click on alt on the keyboard and the from the menus at the top select Customer and then emergency(the last option).
Type in the phones IMEI (located at the box of the phone or on a sticker under the battery) without dashes, just numbers.
Finally click on Check and follow the instructions on the screen.
You should be ready as new after 10-15 minutes with the standard V10B firmware and you should not even lose data.
Tell me if that helped so if it didn't we can still fix it I'm sure
Note: I'm aware that 3.3.0 is the latest USB driver that it ships with the phone but for some reason I had only success to flash the phone using the older 3.2.1
That does not work for our problem, just a blank screen is better than stuck in firmware update mode :s
m33ts4k0z said:
Don't panic, I managed to totally brick my phone today and LG told me to send it back for DOA but I managed to recover it in the end.
My phone wouldn't show anything on the screen, it remained black so I can say your position sounds much better than mine.
What you will need:
USB Drivers - Download from here (Check note)
LG Mobile Support Tool (LGMST) - Download from here
Before you start: Disconnect the phone from the computer and totally remove the battery.
So here we go:
!!!REMOVE ALL THE LG USB DRIVERS FROM THE SYSTEM BEFORE YOU CONTINUE!!! Go to add remove programs, select the LG United entry and then uninstall it.
First install the USB Driver from the link above and wait until it has finished with the setup.
Then run the LGMST. When it starts and it says "Disconnected." then put the battery back to the phone and connect the phone to the computer.
Press ONLY the Power button and wait until something happens. If you see that the phones boots and the LGMST starts it by itself then wait till it stops with all the information gathering stuff.
Then regardless of what the program says of you having an update or not, DON'T START THAT UPDATE!
Click on alt on the keyboard and the from the menus at the top select Customer and then emergency(the last option).
Type in the phones IMEI (located at the box of the phone or on a sticker under the battery) without dashes, just numbers.
Finally click on Check and follow the instructions on the screen.
You should be ready as new after 10-15 minutes with the standard V10B firmware and you should not even lose data.
Tell me if that helped so if it didn't we can still fix it I'm sure
Note: I'm aware that 3.3.0 is the latest USB driver that it ships with the phone but for some reason I had only success to flash the phone using the older 3.2.1
Click to expand...
Click to collapse
I'm afraid that didn't work (I think I'm gonna cry soon)
When I go to the Customer Support option, the last option isn't called Emergency it's called "Recovery Phone" and seems to launch exactly the same thing as it does if I click the big "Start Updating" button. There is no option named Emergency at all. Does that mean my phone isn't/wont/can't boot into Emergency mode?
I don't even hold down the power button for my phone to switch on, the second I insert the battery it boots into Clockwork Recovery. If I power off the phone and connect the USB, I don't get the battery charging animation or anything, the screen just remains completely blank. Then if I press the power button (alone or with anything else) it just boots to Clockwork recovery.
The LG Mobile Support Tool seems to detect the phone in this state, but as I said, when it tries to do the download, I just get an error saying "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update". The version of the Mobile Support Tool that it's installing is 1.5.1.8 after downloading from your provided link, just incase you need to know that. It seems the tool automatically updates itself on every launch.
Someone also seems to have posted the actual ROM in this thread, http://forum.xda-developers.com/showthread.php?t=1155874 would installing this perhaps assist? Is it even possible to install this when my phone wont boot up past the recovery manager? If it is possible can someone perhaps advise me how?
__________
P_U_A_John said:
Try the following thread http://forum.xda-developers.com/showthread.php?p=15782541#post15782541
Click to expand...
Click to collapse
Unfortunately the phone wont boot into Emergency mode. The clockwork Recovery mod seems to have taken over all of the boot options. If I hold the volume up key and press the power button, nothing happens. If I hold the volume down key and the power button, it boots to clockwork recovery. If I just press power, boots to clockwork recovery.
Is there any way to strip off Clockwork recovery and restore the original/stock recovery onto the phone? Or even just remove Clockwork recovery so that it just hangs on the LG boot screen? (See reasoning for this below)
I can still select the USB mount option in Clockwork recovery and the PC still picks it up as a storage device and I can browse around.
The phone is only 7 days old, so I'm almost tempted to just delete the internal memory so that clockwork doesn't show up, then take the phone back to the store and say it wont boot up and try to get it replaced.
Or what would happen if I renamed the clockworkmod folder on the phone's hard drive?
(Just another note, I don't have an external SD card in the phone, just the internal memory)
__________
P_U_A_John said:
1)Plug USB cable
2)Hold "POWER+VOL.UP" (Wait logo LG and mobile screen off) 10 seconds !! For Emergency mode!
3)Hold a second time "POWER+VOL.UP" 10 seconds (the mobile is detected by LGMobile update)
The screen is off in this mode.
PS:
I am trying to upload a backup of the rom.
You may be able to restore from the recovery clockwork ... but it must be 4.0.0.9
Click to expand...
Click to collapse
I do have 4.0.0.9 of the ClockworkMod recovery.
I've tried holding the up volume key and then holding the power key, and I do seem to get emergency mode with the LG Mobile update software detects the phone (with no Clockwork Recovery mod showing on screen) however when I try to use the Recovery phone option, I still get the same error "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update"
If you can upload a backup of the ROM and advise on how to install it via Clockwork, you will be my hero.
1)Plug USB cable
2)Hold "POWER+VOL.UP" (Wait logo LG and mobile screen off) 10 seconds !! For Emergency mode!
3)Hold a second time "POWER+VOL.UP" 10 seconds (the mobile is detected by LGMobile update)
The screen is off in this mode.
PS:
I am trying to upload a backup of the rom.
You may be able to restore from the recovery clockwork ... but it must be 4.0.0.9
Click to expand...
Click to collapse
I do have 4.0.0.9 of the ClockworkMod recovery.
I've tried holding the up volume key and then holding the power key, and I do seem to get emergency mode with the LG Mobile update software detects the phone (with no Clockwork Recovery mod showing on screen) however when I try to use the Recovery phone option, I still get the same error "Updating is not possible any longer due to a fatal error while the LG Mobile Phone Software Update"
If you can upload a backup of the ROM and advise on how to install it via Clockwork, you will be my hero.
Click to expand...
Click to collapse
I had the same error "fatal error " your not putting it in recovery mode right I fixed myn
Sent from my LG-P920 using Tapatalk
ik911 said:
I had the same error "fatal error " your not putting it in recovery mode right I fixed myn
Sent from my LG-P920 using Tapatalk
Click to expand...
Click to collapse
How else can I put it into Recovery Mode? How can I tell if I've done it right?
I managed to hold the up volume key and hold down the power button, and the LG Mobile Update detected the phone whilst the screen was blank. I thought that meant I was in recovery mode?
I should point out that the LG Logo wasn't flashing up however. I only ever see the LG Logo before it boots into Clockwork RecoveryMod
I also got that fatal error thing when i bricked my phone. For me the phone would start flashing but it got stuck at 17% and then an error followed saying that there was a communication problem between the phone and the pc. My solution was to switch from my desktop computer to my laptop and the procedure ran smoothly after.
You said that the phone powers up directly after you connect it to the pc and while having the support tool running?
You can try to shut it down so it shows a black screen as you said and then try to boot into emergency mode with the vol.up+power button.
The windows sounds might help you on that. you can listen from the computer when the phone connects/powers up or not.
EDIT: Just read your post, if the phone remains black is a good thing.
if your update fails or goes into clockwork recovery etc you will need LG mobile update on your pc and install the lg p920 drivers
turn your phone off take the battery out leave it for 10 sec, connect battery and usb cable hold power and volume up hold it for 10 sec let go then do it again for 10 sec
now run LG mobile update click customer support > recover type your imei let it update once finished power up phone now you will get a screen on the phone that says updating let it update
Well I'm not sure what I did differently. Not sure if I wasn't pressing the button hard enough or my finger was slipping off, or if I've just somehow tricked the phone, but the LG Phone Update from the Phone Recovery option is now running.
I've been doing the same thing I was doing before (or at least thought I was doing) and I'm not sure what I did differently....but....fingers crossed..... the download will finish in 40 minutes (on a crappy connection at the moment) so I'll be able to see what happens then....
UPDATE -
Progress, though not quite yet success.
The LG Mobile Support tool downloaded the software and applied the update succesfully, though my phone didn't automatically restart. I pressed the power button however and it loaded up and not into Clockwork Recovery Mod. It's not however sitting on an "Updating Firmware" screen and the progress bar doesn't seem to be filling at all.
How long does this part of the process normally take?
Does the phone need to be connected to USB for this part of the process? The LG Mobile Support Tool says the phone is disconnected so I'm guessing there's no active data connection between the PC and phone, just power.
Does this normally take a while? Or should I perhaps try the recovery again?
Lagamorph said:
Well I'm not sure what I did differently. Not sure if I wasn't pressing the button hard enough or my finger was slipping off, or if I've just somehow tricked the phone, but the LG Phone Update from the Phone Recovery option is now running.
I've been doing the same thing I was doing before (or at least thought I was doing) and I'm not sure what I did differently....but....fingers crossed..... the download will finish in 40 minutes (on a crappy connection at the moment) so I'll be able to see what happens then....
UPDATE -
Progress, though not quite yet success.
The LG Mobile Support tool downloaded the software and applied the update succesfully, though my phone didn't automatically restart. I pressed the power button however and it loaded up and not into Clockwork Recovery Mod. It's not however sitting on an "Updating Firmware" screen and the progress bar doesn't seem to be filling at all.
How long does this part of the process normally take?
Does the phone need to be connected to USB for this part of the process? The LG Mobile Support Tool says the phone is disconnected so I'm guessing there's no active data connection between the PC and phone, just power.
Does this normally take a while? Or should I perhaps try the recovery again?
Click to expand...
Click to collapse
This is only supposed to happen when you apply the OTA update. Try to reapply the stock firmware in emergency mode. After the program applies the firmware, it should boot up the phone by itself in android and give you a success or finish message on the computer.
m33ts4k0z said:
This is only supposed to happen when you apply the OTA update. Try to reapply the stock firmware in emergency mode. After the program applies the firmware, it should boot up the phone by itself in android and give you a success or finish message on the computer.
Click to expand...
Click to collapse
Is applying the Stock Firmware not what I did with the LG Mobile Support Tool when it downloaded that huge 300MB+ file?
I have contacted the customer services for Carphone Warehouse, and the guy advised that if the phone seemed to have developed a fault and wouldn't start, then since it's within 28 days of purcahse I can get a like for like replacement. Might have to go ahead and do that this evening.
Hi
Can anyone help please? Also, are there anyone having similar issue.
Issue: Pressing the power button is not starting my device. In order to power on I have to connect charger (not usb with PC) and then press power button. What I have noticed is that once I switch off my phone it gets in to "emergency/recover mode". I came to this conclusion because after I switch the phone off, take battery out and put back in and then connect usb cable with my PC. I can see OMAP driver loads and also in the PC's Device Manager I am able to see LG CDMA.... under "ports".
It was not like this until i started several attempts to flash baseband.
Sequence of actions
Here is the sequence of actions I went through and end up having my phone at this stage
1. Followed the procedure (http://forum.xda-developers.com/showpost.php?p=17177547&postcount=2) step by step using LG flash tool. The application was constantly crashing (PC is running on XP pro). Before flashing baseband I flashed GB hence I lost radio.
2. To bring back my radio I had to reflash 2.2 following the same procedure (emergency recovery method) in the link given in baseband flashing.
3. After finishing the recovery flash I could not start my phone using power button. I started thinking that I bricked my phone. I left it for a day. Then I thought that the battery is fully drained and is the reason for not powering on. When I connected charger I started seeing LG logo and also the phone was started. I was more excited and happy that my phone was not bricked. After this point I need charger connected everytime when i want switch on my phone. so, I am scared to swtich off my phone unless I have charger handy to me.
4. I removed all the application (LG flashing related) including LG drivers I installed before. Now I reinstalled all the necessary app and drivers for baseband flashing. This time baseband flashing was done successfully (though at 22%). Then I flashed GB rom and everything works fine.
The only issue i have is, I can not switch on my phone without charger connected.
If anyone knows solution please help me.
Thanks in advance.
http://forum.xda-developers.com/showthread.php?t=1331390
I used to have the same problem,
I think its a problem about boot,
when I use lg tools it always gives error, because phone wont boot without charger, so it cant continue upgrading
I try flasing original kdz file from lg flash tool, and use emergency rescue mode,
I dont know but it somehow repair the boot
you can fix permissions before you use lg tools.
what error do you have while using lg tool?
can you post the screen capture
nurikarakaya said:
http://forum.xda-developers.com/showthread.php?t=1331390
I used to have the same problem,
I think its a problem about boot,
when I use lg tools it always gives error, because phone wont boot without charger, so it cant continue upgrading
I try flasing original kdz file from lg flash tool, and use emergency rescue mode,
I dont know but it somehow repair the boot
you can fix permissions before you use lg tools.
what error do you have while using lg tool?
can you post the screen capture
Click to expand...
Click to collapse
After i uninstalled all the drivers (incl. LG tools) and reinstalled and I am not seeing any more error while using LG tools. I even flashed GB baseband twice but no use. The link you have given explains the same issue I have.
I think you have to install froyo version of baseband and firmware first,
then try
http://forum.xda-developers.com/showthread.php?t=1186406
STUCK AT LG LOGO:
with factory reset!
1) Start LG Mobile update
2) Power off your phone without USB cable
3) Connect the USB cable and wait for the LG logo and the annimation battery
4) Pressing Vol.up + power 6-7 seconde wait for the LG logo and The screen turns off
5) Again pressing Vol.up + power 6-7 seconde and wait until the drivers are installed (LG Mobile update detects your phone and the screen is always off)
-If this is the first time the driver install redone the item 5).
6) Click on User/Support then emergency mode, insert your IMEI and click on check
7) Wait for download and upgrading (15/20 min)
Questions or Problems Should Not Be Posted in the Development Forum
Please Post in the Correct Forums and Read THIS
Moving to General
lufc said:
Questions or Problems Should Not Be Posted in the Development Forum
Please Post in the Correct Forums and Read THIS
Moving to General
Click to expand...
Click to collapse
Thanks. will stick to the rule in future..
nurikarakaya said:
I think you have to install froyo version of baseband and firmware first,
then try
http://forum.xda-developers.com/showthread.php?t=1186406
STUCK AT LG LOGO:
with factory reset!
1) Start LG Mobile update
2) Power off your phone without USB cable
3) Connect the USB cable and wait for the LG logo and the annimation battery
4) Pressing Vol.up + power 6-7 seconde wait for the LG logo and The screen turns off
5) Again pressing Vol.up + power 6-7 seconde and wait until the drivers are installed (LG Mobile update detects your phone and the screen is always off)
-If this is the first time the driver install redone the item 5).
6) Click on User/Support then emergency mode, insert your IMEI and click on check
7) Wait for download and upgrading (15/20 min)
Click to expand...
Click to collapse
Thanks. I will try it tonight or will wait for official GB release then i can do the this emergency update.
Hello guys,
I came here because I need help with my LG Optimus 3D which is not booting anymore. It's not even turning on anymore, so I can't even get into Recovery Mode or ClockWorkMod. ADB also doesn't detect my phone.
Phone is rooted
ClockWorkMod installed
PACMan Rom (4.2.2)
The phone was working fine until it suddenly rebooted and got stuck at booting at the PAC loading screen. After it didn't boot after 10 minutes, I pulled the battery and since then it won't turn on anymore.
Anyone got any idea how I might be able to fix it?
first , connect charger to the phone in same condition and leave it for 5-6 hours. even though the screen is black or if phone starts rebooting in loop. just leave it like that . the battery should get charged a bit just to make 2-3 tries. try boot into recovery
second, disconnect battery and hold down volume up and connect usb, check if its getting detected in computer. if yes then install fastboot by omap4boot for optimus tool and flash a recovery again.
Last night my G6 rebooted itself and now it is stuck in a fastboot loop. It keeps restarting itself when connected to charger or PC. Nothing happens when phone is disconnected from charger/pc. Only message on screen is "Keep pressing power key for 10 seconds to exit fastboot mode" but it doesnt help. Phone was stock and not rooted...
MLu75 said:
Last night my G6 rebooted itself and now it is stuck in a fastboot loop. It keeps restarting itself when connected to charger or PC. Nothing happens when phone is disconnected from charger/pc. Only message on screen is "Keep pressing power key for 10 seconds to exit fastboot mode" but it doesnt help. Phone was stock and not rooted...
Click to expand...
Click to collapse
did you try to flash the newest rom ?
By the way .... which G6 do you have ? (L11, u10 etc..)
In the title it says U10, thought that would be enough info
I never flashed/rooted a phone before so I didnt try anything so far...
edit: I tried the suggestion from this post: http://forum.xda-developers.com/showpost.php?p=59545669&postcount=4
1. redownload the rom file from official location. ( http://consumer.huawei.com/kh/suppor...h.htm?id=38361 )
It is the official for g6-l11 (-> dl a version for G^-u10 instead)
2. put the update.app into dload folder on your sd card (unpack from the zip)
3. shut down your phone
4. hold volume+ volume- and power button. When it start to boot release the power button, and hold both the volumes until the instalation starts
5. you will see that firmware flashing begin, wait for the end
Click to expand...
Click to collapse
It seems to work, I see the green android dude and text "updating from external storage" but the problem is the phone keeps restarting itself so it doesnt continue with the update... I suspect sometings wrong with the battery, short circuit maybe?
edit 2:
After giving up last night i tried the above procedure one more time this morning...and for some reason the installation continued. Phone has been up and running again since 8:30 this morning...
where can i get stock rom that can be flashed via sp flash tool? my huawei ascend g6-u10 is bricked after flashing b330. any solution for this?
my phone is dead but my pc can still recognize it
I've broken my phone! I was rooted, and was installing a custom rom. It worked fine for a few hours, and now the phone won't boot up in normal, recovery or fastboot modes. All I get is the android logo and then a white screen for a few seconds, and this repeats until i get fed up and turn it off again.
My device is a Vodafone 785 and my pc is running Windows 7 with the latest drivers installed and updated.
When I plug the phone into the computer, it tries to register but the flashtool says the device is not recognized, so I can't re-install my recovery image.
I've been at this for about three weeks now, and I cannot for the life of me figure out how to get this working again. Can someone please help?
coling24 said:
I've broken my phone! I was rooted, and was installing a custom rom. It worked fine for a few hours, and now the phone won't boot up in normal, recovery or fastboot modes. All I get is the android logo and then a white screen for a few seconds, and this repeats until i get fed up and turn it off again.
My device is a Vodafone 785 and my pc is running Windows 7 with the latest drivers installed and updated.
When I plug the phone into the computer, it tries to register but the flashtool says the device is not recognized, so I can't re-install my recovery image.
I've been at this for about three weeks now, and I cannot for the life of me figure out how to get this working again. Can someone please help?
Click to expand...
Click to collapse
Hi, try this:
http://forum.xda-developers.com/android/help/vodafone-smart-4-mini-killed-vodafone-t2869185
Yes I tried that one and most of the other threads about this damn phone. It won't boot in recovery. I've tried Power button and volume up AND Power button and volume down. All I get is android logo for a few seconds and white screen for another few seconds and this will loop until the end of time. Using SP Flashtool, the computer won't recognize the device when I plug in the USB with either the battery removed or inserted into the phone.
coling24 said:
Yes I tried that one and most of the other threads about this damn phone. It won't boot in recovery. I've tried Power button and volume up AND Power button and volume down. All I get is android logo for a few seconds and white screen for another few seconds and this will loop until the end of time. Using SP Flashtool, the computer won't recognize the device when I plug in the USB with either the battery removed or inserted into the phone.
Click to expand...
Click to collapse
Unfortunately, it sounds like the device may be unrecoverable.
I'm not for giving up. Somehow I'll find a way to fix this thing. :fingers-crossed:
coling24 said:
I'm not for giving up. Somehow I'll find a way to fix this thing. :fingers-crossed:
Click to expand...
Click to collapse
Good luck!