1. Take the NI1 OTA update. (Should the update fail see troubleshooting section below).
2. Place your phone into "Download Mode" (press and hold the "Home", "Volume Down", and "Power" keys until the phone powers on and displays warning screen, then press "Volume Up" key).
3. Flash the I337_NC1_Stock_Kernel using Odin's PDA slot(AP in Odin v3.09+).
4. Root using Towelroot-v3.apk(internet access not required).
5. Power off then boot into "Download Mode" again.
6. Flash the I337_NI1_Stock_Kernel also in Odin's PDA slot(AP in Odin v3.09+).
7. Install SuperSU to manage root access. Done!
Important!: Do not skip any of the above steps or you may experience issues with your device.
Notes:
1. After flashing the NC1 kernel your phone may run a little wonky, e.g. extreme lag, no wifi, etc., and towelroot may not root on the first try. If that happens reboot and try towelroot once again. Once rooted and after flashing the NI1 kernel your phone will again run like a champ!
2. Neither User Data nor knox warranty flag will be affected by following the above process.
3. The most common cause of a failed Odin flash is a bad usb port or cable. Please check before reporting a failure.
Troubleshooting:
Should the NI1 ota update fail consider flashing back to stock NB1 using either file in this thread: I337UCUFNB1 4.4 Stock Odin Tars & System Dump. Then take the NI1 ota update. (or place the I337_NB1toNI1_OTA_Update.zip onto your ext-sdcard and sideload from stock recovery). Once updated to NI1 continue from Step 2 above.
Alternative Method for Safestrap Users:
1. Use Safestrap's Backup Function to back-up User Data.
2. Place the I337UCUFNI1_100%_Stock_Rooted_ROM.zip onto your ext-sdcard.
3. Reboot into Safestrap recovery then perform an "Advanced Wipe" and wipe everything but your ext-sdcard.
4. Flash the I337UCUFNI1_100%_Stock_Rooted_ROM.zip using "Stock Slot."
5. Once complete press "Home" then reboot into "Download Mode."
6. Flash the I337_NI1_Stock_Kernel in Odin's PDA slot (AP in Odin v3.09+).
7. Reboot into Safestrap recovery and use the Restore Function to restore User Data. Done!
Notes:
1. The I337UCUFNI1_100%_Stock_Rooted_ROM.zip process will update your Modem, Non-hlos, System, Kernel, and Stock Recovery to NI1 but does not include the NI1 Bootloader.
2. Follow all of the above steps in the order provided and do not skip any steps or you may experience issues with your device!
I337_NI1 Stock Modem, Recovery, and System Dump
I337_NI1_Stock_Modem.tar.md5
I337_NI1_Stock_Recovery.tar.md5
Flash in PDA Slot in Odin(AP in Odin v3.09+).
I337_NI1_System_Dump.rar (If you don't know what this is you don't need it).
muniz_ri said:
reserved
Click to expand...
Click to collapse
Nice now all i need is the system dump from NI1 And Flashable Modem!
@muniz_ri
You done it again Bud.....Amazing
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
@Venom0642
Sorry double post ...Tapatalk error
Venom0642 said:
Nice now all i need is the system dump from NI1 And Flashable Modem!
Click to expand...
Click to collapse
Uploading system dump now but may take awhile. My upload speed sucks.
muniz_ri said:
Uploading system dump now but may take awhile. My upload speed sucks.
Click to expand...
Click to collapse
Awesome bro thanks curious though is this 4.4.4 or is it still 4.4.2 ?
Sent From My Galaxy S5 SAMSUNG-SM-G900A Running On New Deadly Venom v4.0.0 KitKat 4.4.2
Venom0642 said:
Awesome bro thanks curious though is this 4.4.4 or is it still 4.4.2 ?
Sent From My Galaxy S5 SAMSUNG-SM-G900A Running On New Deadly Venom v4.0.0 KitKat 4.4.2
Click to expand...
Click to collapse
Still 4.4.2 but seems noticeably faster, mabe placebo. IDK
muniz_ri said:
Still 4.4.2 but seems noticeably faster, mabe placebo. IDK
Click to expand...
Click to collapse
Oh ok thanks someone should be soon enough adding modem flashable.
Sent From My Galaxy S5 SAMSUNG-SM-G900A Running On New Deadly Venom v4.0.0 KitKat 4.4.2
muniz_ri said:
Uploading system dump now but may take awhile. My upload speed sucks.
Click to expand...
Click to collapse
Venom0642 said:
Oh ok thanks someone should be soon enough adding modem flashable.
Sent From My Galaxy S5 SAMSUNG-SM-G900A Running On New Deadly Venom v4.0.0 KitKat 4.4.2
Click to expand...
Click to collapse
I will work on the modem and stock recovery when I get some extra time. And I take that back about my uploads speed...time warner just upgraded my plan free of charge, weird! I will post the link to the dump in a few minutes.
muniz_ri said:
I will work on the modem and stock recovery when I get some extra time. And I take that back about my uploads speed...TW just upgraded my plan free of charge, weird! I will post the link to the dump in a few minutes.
Click to expand...
Click to collapse
Nice thanks again[emoji106]
Sent From My Galaxy S5 SAMSUNG-SM-G900A Running On New Deadly Venom v4.0.0 KitKat 4.4.2
Venom0642 said:
Nice now all i need is the system dump from NI1 And Flashable Modem!
Click to expand...
Click to collapse
I337_NI1_System_Dump.rar
muniz_ri said:
I337_NI1_System_Dump.rar
Click to expand...
Click to collapse
Awesome Thanks! :good:
rooting
I just got this phone today and it just updated as well. I have rooted my old S4s and have some experience. Do i need to do anything to this phone before I follow the instructions in muniz's first post? Do i need to have alreay been rooted or anything? My phone is completely stock at the moment. Thanks.
Venom0642 said:
Nice now all i need is the system dump from NI1 And Flashable Modem!
Click to expand...
Click to collapse
Modems and Recovery added to Post# 2.
douggiephresh said:
I just got this phone today and it just updated as well. I have rooted my old S4s and have some experience. Do i need to do anything to this phone before I follow the instructions in muniz's first post? Do i need to have alreay been rooted or anything? My phone is completely stock at the moment. Thanks.
Click to expand...
Click to collapse
Nope
Is there any kernel modules yet for NI1?
Sent from my SGH-I337 using XDA Free mobile app
chitown835 said:
Is there any kernel modules yet for NI1?
Sent from my SGH-I337 using XDA Free mobile app
Click to expand...
Click to collapse
You can pull the modules from the system dump in post #12.
hey,
I wanted to know one thing ..
my phone is already nc1 root stock, what should I do to upgrade it to nc1 root stock ??
Thanks
Could anyone upload a NI1 update.zip? Thanks in advance.
Related
[Easy upgrade to 4.3][OS 4.3 MK9][03/01/2014]GT-N7100
Code:
*** Disclaimer
-- Flashing roms especially with bootloaders are dangerous, make sure you make a nandroid backup before hand,Please follow the instructions carefully
Introduction
The aim of this project is to make easy to upgrade to 4.3 or downgrade to 4.1.
This rom is the official samsung 4.3 [N7100XXUEMK9] without knox files or bootloader.
Rom is for people that wish to upgrade to 4.3 and keep their device in Official status without knox.
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Installation instructions via Odin pc
You must reset your device to factory defaults before flashing.
Download file and extract it
Put your device into download mode [volume down, power button and home button]. Keep them pressed until the download mode shows up then press volume up]
Launch Odin ,select pda and browse to Final.tar.md5 and press start in Odin.
this will take a while
Done!
Click to expand...
Click to collapse
Installation instructions via Mobile Odin
Copy final.tar.md5 to the storage card of your device
-- Tap the Open file … tab mobile odin ,
browse to the final.tar.md5 location and select it,
tick all boxes under everoot and Wipe [this will **root the rom and wipe the device]
Now press flash Firmware
Now you must Download and flash this package Via pc Odin!
Done!
Click to expand...
Click to collapse
Notes:
Click to expand...
Click to collapse
If Odin fails don't despair put you phone into download mode again and re-flash even if it happens more that once.
Avoid Usb 3 ports.
Click to expand...
Click to collapse
Rooting instructions
option-1Kingo root download the program and install on your pc follow the instructions to root your device.
option 2 option Chainfire CF-AUTO-ROOT you will need triangle away to reset your binary count after.
option 3- **Chanfire Mobile Odin
Click the above Options to redirect you to theirs respective pages.
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Download
Download rom from link below
-- Download
Click to expand...
Click to collapse
Changelog
Code:
Current changelog: -- 03/01/2014
[BASE] -- MK9 BTU
[BUILD NUMBER]-- JSS15J.N7100XXUEML3
KERNEL] -- 3.0.31-2138564
[BOOTLOADER] -- MJ5
[RADIO] -- MJ9
[SELINUX STATUS] ENFORCING
FAQ
How to downgrade to 4.1?
Coming soon.....
Can i flash a custom rom after this?
Yes .
Can i use this package to Set my device to OFFICIAL status?
yes, After flashing it use Triangle away to Fix your Status.
Can i use this Rom to revert Knox to X0?
NO.
Will this package Trigger my binary?
No.
Q. I have already flashed a 4.3 custom rom, can i still flash this?
Yes
Click to expand...
Click to collapse
Thanks To/Credits
Code:
* Chaifire,Kingo root, and all XDA Developers.
* insert text
XDA:DevDB Information
4.3 upgrade, a ROM for the Samsung Galaxy Note II
Contributors
faria
ROM OS Version: 4.3.x Jellybean
ROM Kernel: Linux 3.0.x
ROM Firmware Required: 4.1
Based On: Stock Samsung
Version Information
Status: Stable
Created 2014-01-04
Last Updated 2014-01-04
Click to expand...
Click to collapse
Click to expand...
Click to collapse
reserved*****
Does this wipes data ?
Or can I do an "upgrade" from stock rooted (4.1, flashed via Odin) to this version ?
No It doesn't wipe data, if you got rooted stock It should be fine. Never the less a backup and a wipe is recommended.
Sent from my GT-N7100 using Tapatalk
so if i am on 4.1.2.....and follow d procedure....i will have knox counter as 0?
what about recovery? which recovery you would suggest provided it shouldnt set the counter to 1....as i dont want to void the warranty...??
and thanks for the latest 4.3 for note II...been waiting for the simple instructions !!:highfive:
swapyworld said:
so if i am on 4.1.2.....and follow d procedure....i will have knox counter as 0?
what about recovery? which recovery you would suggest provided it shouldnt set the counter to 1....as i dont want to void the warranty...??
and thanks for the latest 4.3 for note II...been waiting for the simple instructions !!:highfive:
Click to expand...
Click to collapse
1- Yes
2- you can flash any recovery you wish, but of course it will trigger the binary count if you wish to remove the binary count you must flash this package from here http://forum.xda-developers.com/showthread.php?t=2588557 and then run triangle away.
reserved.. thanx
Sent from my GT-N7100 using Tapatalk
I'm a bit lost in all those firmware versions
I'm trying to update my girlfriend's note2 to 4.3
Here is her phone's info :
Baseband : N7100XXDME4
Version number : JZ054.N7100XXDME6
CSC : N7100XADME2
No recovery installed, and counter still at 0
Can I flash your version safely from her version ?
@ bud77.Yes.
Sent from my GT-N7100 using Tapatalk
wrongpost
Worked perfectly, plus root via kingoapp
I noticed it is odexed, do you plan on a deodexed one ?
Sent from my Nexus 5
I will give a try, but my priority is to make it prerooted like a did before but on 4.3 the root gets disabled at first boot, so far.
Now that you are on 4.3 you can install a 4.3 deodexed rom via custom recovery or mobile odin, there is 2 such rooms in the development treads.
Sent from my GT-N7100 using Tapatalk
Everything went ok with the upgrading, except that Triangle Away not seem to work anymore?
I have run version 3.10 + unfreezed the sysscope file in Titanium B, but I'm still "custom".
Maybe it doesn't work when I have used the Kingo root? Do you have any advice..?
Regards
Unfreeze sysscope, unistall triangle away, reboot, clear cache and wipe data of sysscope and Interprise sysscope, now reinstall triangle away an run it.
Sent from my GT-N7100 using Tapatalk
I heard many comments about Mobile Odin not working with 4.3
Has anyone successfuly flashed this?
I have Mobile Odin Pro and 4.1.2
My phone is rooted but with a stock Samsung ROM.
Wondering if 4.1.2>4.3 will go smoothly with Mobile Odin and this ROM, keeping root. Anyone?
If you follow my instructions for mobile odin it should work. ?
Sent from my GT-N7100 using Tapatalk
faria said:
Unfreeze sysscope, unistall triangle away, reboot, clear cache and wipe data of sysscope and Interprise sysscope, now reinstall triangle away an run it.
Click to expand...
Click to collapse
Did it all, in the exact order. Still custom. What gives?
With 4.1.2 it worked fine, but I used CF autoroot then.
Thanx for trying to help.
Televinken said:
Did it all, in the exact order. Still custom. What gives?
With 4.1.2 it worked fine, but I used CF autoroot then.
Thanx for trying to help.
Click to expand...
Click to collapse
Still "custom"where? In the Os or download mode? Your binary is 0 rigth?
Sent from my GT-N7100 using Tapatalk
faria said:
Still "custom"where? In the Os or download mode?
Click to expand...
Click to collapse
In the OS. So now OTA is gone, & so is updating via Kies.
When I check the binary, it shows "1". *sigh*
Televinken said:
In the OS. So now OTA is gone, & so is updating via Kies.
When I check the binary, it shows "1". *sigh*
Click to expand...
Click to collapse
Flash this package then run triangle away . http://forum.xda-developers.com/showthread.php?t=2588557
Sent from my GT-N7100 using Tapatalk
1. Take the NJ4 OTA update.
2. Download and install Towelroot-v3.apk(this version does not require internet access).
3. Place your phone into "Download Mode" (press and hold the "Home", "Volume Down", and "Power" keys until the phone powers on and displays warning screen, then press "Volume Up" key) and flash the I337_NC1_Stock_Kernel using Odin's PDA slot(AP in Odin v3.09+).
4. Open the Towelroot app from your app drawer and press "Make it Rain" to root your device.
5. Power off then boot into "Download Mode" again and flash the I337_NJ4_Stock_Kernel also in Odin's PDA slot(AP in Odin v3.09+).
6. Install SuperSU to manage root access. Done!
Troubleshooting:
1. Should the NJ4 ota update fail consider flashing back to stock NB1 using either file in this thread: I337UCUFNB1 4.4 Stock Odin Tars, then take the NJ4 ota update. Or, place the I337_NB1_to_NJ4_OTA_Update.zip onto your ext-sdcard and sideload from stock recovery. Once updated to NJ4 continue from Step 2 above.
2. When flashing the kernels the most common cause of an Odin flash failure is a faulty usb port or cable. Please check before reporting a failure!
Notes:
1. After flashing the NC1 kernel your phone may run a little wonky, e.g. extreme lag, no wifi, etc., and towelroot may not root on the first try. If that happens reboot and try towelroot once again. Once rooted and after flashing the NJ4 kernel your phone will again run like a champ!
2. Neither User Data nor knox warranty flag will be affected by following the above process.
3. For a great Noob FAQ see this Post thanks to @gonenorsk!
Alternative Safestrap Method (Updated 3/29/2015 - Odin no longer required):
1. Place the I337UCUFNJ4_100%_Stock_Rooted_ROM onto your ext-sdcard.
2. From Safestrap recovery press "Backup" and backup your User Data.
3. Once complete, from the main menu press "Wipe" then "Advanced Wipe" and wipe everything but your ext-sdcard.
4. From the main menu press "Install," then select and install the I337UCUFNJ4_100%_Stock_Rooted_ROM.
5. Once complete, press "Restore" and restore your User Data.
6. From the main menu press "Reboot," then "System." Done!
Notes:
1. The above process will not affect your User Data or knox warranty flag.
2. This process will update your Modem, Non-hlos, System, Kernel, Stock Recovery, and Bootloader to NJ4 (BusyBox is also pre-installed).
3. The User Data "Backup" and "Restore" steps in the above instructions are not mandatory but will greatly reduce your device's set-up time. All currently installed non-system apps and settings will be automatically restored.
Credits:
@benwaffle for his flashboot script(built into the ROM) allowing the flashing of kernels via Safestrap.
@muniz_ri
U done it again bud..... Amazing
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
@muniz_ri
Well that was fast! Good job buddy, keep up the good work!
muniz_ri said:
...
I337UCUFNJ4_100%_Stock_Rooted_ROM.zip(Uploading.....
...
Click to expand...
Click to collapse
Still uploading?
I337UCUFNJ4 Please Upload Pure OTA File .. I Need To Update .. Please Anyone Help Me Without Rooting OTA .. I Need Help Me
Used Safestrap method and it worked flawlessly. Up and running like a champ. Thank you so much!
Please Help Me
Respected Sir,
Please Upload I337UCUFNJ4 OTA File . I Want To Update . Please Upload File For Upload. Please Anyone Upload OTA Update The File Sir.. From NI1 To NJ4.. OTA File
@muniz_ri could you pull the Modem, I can package it up and put it in my modem thread? With full credit to you. Let me know here or via PM. Thanks
WiFi Tethering
Thanks guys for the root instructions but WiFi tethering will work or we should wait for NJ4 Modules ?
RockRatt said:
@muniz_ri could you pull the Modem, I can package it up and put it in my modem thread? With full credit to you. Let me know here or via PM. Thanks
Click to expand...
Click to collapse
The modem img is in the rom zip.
muniz_ri said:
The modem img is in the rom zip.
Click to expand...
Click to collapse
Cool... Thanks. Trying to download now. Thanks again for ALL you do
Reverting back ?!
Hello,
Thanks for the good job.
I was wondering, is there possibility of going back to NI1(or NB1) from NJ4? (with odining full rom)
Thanks,
joseph230 said:
Hello,
Thanks for the good job.
I was wondering, is there possibility of going back to NI1(or NB1) from NJ4? (with odining full rom)
Thanks,
Click to expand...
Click to collapse
Yes, you should be able to downgrade back to nb1.
Wanted to say a quick thx to those that recently donated. Unfortunately paypal does not provide your user name in the notification so i cant pm my thx but you know who you are. Donations are obviously not required but just wanted to say thank you.
Modules
First of all thank you very much for your hard work. The alternative method worked perfectly. Does anyone have the NJ4 modules yet? WiFi not working on mine.
malanets1990 said:
First of all thank you very much for your hard work. The alternative method worked perfectly. Does anyone have the NJ4 modules yet? WiFi not working on mine.
Click to expand...
Click to collapse
The nj4 modules are already in the rom. Make sure you remembered to flash the nj4 kernel.
muniz_ri said:
The nj4 modules are already in the rom. Make sure you remembered to flash the nj4 kernel.
Click to expand...
Click to collapse
I did flash the kernel but WiFi not working
malanets1990 said:
I did flash the kernel but WiFi not working
Click to expand...
Click to collapse
I would be interested in hearing from others if they are having any wifi issues. Its possible the rom had trouble updating non-hlos. IDK
muniz_ri said:
I would be interested in hearing from others if they are having any wifi issues. Its possible the rom had trouble updating non-hlos. IDK
Click to expand...
Click to collapse
Hey guys just wanted to clarify my situation. When flashing the stock rom, wifi works with no issues. However when I installed a custom rom the wifi is not working. Thats why I was hoping someone had the modules so I could flash after installing the custom rom. Thanks again!
Modules have been uploaded here... https://www.androidfilehost.com/?w=files&flid=17227
Thanks for your hard work @muniz_ri.
FYI - Your regular root instructions worked fine for rooting and installing safestrap. After Odin'ing back the NJ4 kernel, I saw the "force close" you were talking about when you try and launch the safestrap app, but the safestrap menu is still there on reboot.
This is the first of many guides I will be posting and keeping up with.
It will be utilized for Q&A FAQ and HOW TO so we can keep the development thread for development purposes.
Post your questions and Myself or other knowledgeable users of Sac23 ROMS will answer as quickly as possible.
So ......
For starters HOW TO INSTALL a ROM by SAC23
PRE REQUISITE ... YOU MUST BE ON THE 5.0 BOOTLOADER TO RUN THIS ROM
If you need to flash back to a previous stock bootloader
Mini-bootloaders - TWRP or Philz recovery already embedded:
Firmware_Only_Odin_Flashable_ Images_For_4.4.. And_5.0_Roms
Full bootloaders:
4.4.4 - G900PVPU1ANK4_G900PSPT1ANK4_SPR.zip
4.4.2 - [LINK][ROM][ODIN][TAR]SM-G900P NE5 (NE5 Modem/Kernel/ROM - Stock)
Installing with TWRP (View All Supported Devices>>> Find TWRP for your device):
Philz can be used and I will post instructions for it later
This assumes that you ALREADY have TWRP Recovery installed on your phone and you know how to use it.
TWRP Recovery by Ktoonsez: 01.13.2015: http://goo.gl/LgBsuk
Download the ROM of choice...move it onto the EXT SD CARD.
VERY IMPORTANT>>> Move all music, pics, important data from internal storage to the ext SD card and/or to your pc, etc. because during this process, the internal will be completely erased.
Recommended Method to Flash SACS Custom ROMS using TWRP
Boot into TWRP
Select Wipe > Advanced Wipe
Select Dalvik, System, Data, Internal Storage, and Cache. Swipe to Wipe (do this THREE TIMES)
Go back to previous Advanced Wipe screen.
Select Format Data, Type YES, Press GO. (do this THREE TIMES)
Go back to previous Advanced Wipe screen.
Swipe to Factory Reset. (do this THREE TIMES)
Go back to MAIN menu and STOP HERE !!!!! READ NEXT STEP CAREFULLY....
[*]Select REBOOT INTO RECOVERY mode and Swipe to Install Super User. DO NOT REBOOT INTO SYSTEM!
[*]AFTER THE PHONE REBOOTS INTO RECOVERY:
NOW proceed with installing The ROM
Select Install Zip, Drill down to Sac23's Rom you want to flash, and Swipe to install.
Follow on screen instructions (if there are any).
When prompted, REBOOT SYSTEM.
THE FIRST BOOT WILL TAKE A MINIMUM OF 20 MINUTES..... SOME DEVICES EVEN LONGER...
.
.
HAVE PATIENTS
When the Home Screen appears and it is obvious that the install has completed, allow the phone to settle for another 10 minutes BEFORE you begin setting up your personal preferences and accounts.
If everything seems normal, set your phone up and profit.
After setting up your personal info and you are now ready, the first thing you should always do after flashing any ROM is to go to settings, system updates, and refresh/update your PRL & PROFILE then reboot the phone. Second thing is go to settings, more networks, mobile networks, network mode, and select LTE/CDMA.
saved 1
OP HOST LINK HERE
MY MIRROR HOST LINK HERE
MY ANDROIDFILEHOST LINK HERE
MD5 5a5aa948f33d1bc8eb280cd28335ad99
STOCK S5 FLASHABLE MESSAGING APP
STOCK S5 FLASHABLE MESSAGING APP
STOCK S5 MESSAGING APP & STOCK KEYBOARD
ORIGINAL S5 FLASHABLE WHITE KEYBOARD supplied with ver 1 ROM
TWRP Recovery by Ktoonsez: 01.13.2015: http://goo.gl/LgBsuk
Ktoonsez Touchwiz KERNEL Lollipop 5.0 VERSION: 01.03.2015: http://goo.gl/5Dyssj
Always do the following AFTER installing the kernel:
1. Clear cache
2. Clear dalvik
saved 2
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
saved 3
reserved for future use
saved 4
reserved for future use
saved 5
reserved for future use
Can you follow the install instructions if currently on a 4.4.2 or 4.4.4 firmware? Or do you have to odin NKD firmware first?
Ramer said:
Can you follow the install instructions if currently on a 4.4.2 or 4.4.4 firmware? Or do you have to odin NKD firmware first?
Click to expand...
Click to collapse
IF YOU ARE ON 4.42 FIRMWARE THE ROM WON'T BOOT UP YOU NEED 4.4.4 FIRMARE...
YOU CAN YOU FLASH THE NKD FIRMARE WITH ODIN AND RECOVERY AFTER YOU FLASH ..GO BACK TO RECOVERY AND INSTALL THE ROM
http://forum.xda-developers.com/spr...irmwareonlyodinflashabl-imagesfor4-4-t2958614
paco_1 said:
IF YOU ARE ON 4.42 FIRMWARE THE ROM WON'T BOOT UP YOU NEED 4.4.4 FIRMARE...
YOU CAN YOU FLASH THE NKD FIRMARE WITH ODIN AND RECOVERY AFTER YOU FLASH ..GO BACK TO RECOVERY AND INSTALL THE ROM
http://forum.xda-developers.com/spr...irmwareonlyodinflashabl-imagesfor4-4-t2958614
Click to expand...
Click to collapse
Im a little confused. So I have to flash 4.4.4 stock firmware if I'm on 4.4.2, then NKD stock firmware, and then I can flash this? I just want to make sure I'm reading this right.[emoji12]
Super stoked to try this out! Sacs, you do AMAZING WORK!!!!!!
Sent from my SM-G900P using Tapatalk
Ramer said:
Can you follow the install instructions if currently on a 4.4.2 or 4.4.4 firmware? Or do you have to odin NKD firmware first?
Click to expand...
Click to collapse
Thanks @Ramer ... Added to OP
chefbaker11 said:
Im a little confused. So I have to flash 4.4.4 stock firmware if I'm on 4.4.2, then NKD stock firmware, and then I can flash this? I just want to make sure I'm reading this right.[emoji12]
Super stoked to try this out! Sacs, you do AMAZING WORK!!!!!!
Sent from my SM-G900P using Tapatalk
Click to expand...
Click to collapse
you NEED to flash the 5.0 bootloader then the rom
rlmiller said:
you NEED to flash the 5.0 bootloader then the rom
Click to expand...
Click to collapse
Thanks!!! This ROM is amazing! But you know that already, y'all been doing big things for years
Again, Great work and Thanks to all the people involved.
chefbaker11 said:
Thanks!!! This ROM is amazing! But you know that already, y'all been doing big things for years
Again, Great work and Thanks to all the people involved.
Click to expand...
Click to collapse
ORIGINAL S5 FLASHABLE KEYBOARD supplied with ver 1 ROM
rlmiller said:
ORIGINAL S5 FLASHABLE KEYBOARD supplied with ver 1 ROM
Click to expand...
Click to collapse
You guys are almost as fast at responding as your ROMs...lol. Thanks!
I have this swype modded blue with numbers row keyboard I use currently with latest m.o.a.r. im prepping to flash sacs now and wondering if you think this will work with it. I don't remember who released this or where I got it. but thank you to whom ever it was!
SHYZZA said:
I have this swype modded blue with numbers row keyboard I use currently with latest m.o.a.r. im prepping to flash sacs now and wondering if you think this will work with it. I don't remember who released this or where I got it. but thank you to whom ever it was!
Click to expand...
Click to collapse
There's a chance that it will work
Just remember you can flash the keyboard mod again if it breaks
If it works post the file here or move it to my mod section
Sent from my SM-G900P
rlmiller said:
There's a chance that it will work
Just remember you can flash the keyboard mod again if it breaks
If it works post the file here or move it to my mod section
Sent from my SM-G900P
Click to expand...
Click to collapse
Tried it and it just hung on boot after flashing....booo I let it sit for awhile too. Oh well. Another question. Can the clock be moved from center to righ side?
SHYZZA said:
Tried it and it just hung on boot after flashing....booo I let it sit for awhile too. Oh well. Another question. Can the clock be moved from center to righ side?
Click to expand...
Click to collapse
It cannot be moved yet sac is working on some additional mods for the next release
Sent from my SM-G900P
Thanks bud. Its cool it takes time for all the lil tweaks i know. But good to have you guys back man i missed sacs work for sure. You as well my friend! Always top notch!
Ss
EDIT: UPDATED WITH NEW KERNEL INFO FROM @freeza FOUND HERE
The Older Manh_it Kernel has random reboot issues and is NO LONGER RECOMMENDED .....
SO USE FREEZAS KERNEL DOWNLOAD HERE THERE ARE NO KNOWN ISSUES WITH IT AND HE UPDATES REGULARLY
ROOTING will trip knox and tripping knox WILL kill Samsung pay FOREVER...even if you flash back the stock tar
I AM NOT RESPONSIBLE FOR ANYTHING THAT HAPPENS TO YOU PHONE. ... IT IS YOUR DECISION TO TAKE THE PLUNGE.
Anyone that tries this and gets bootloops and cannot recover here is a link to the OGD stock tar file... flash in Odin AP slot from download mode you should recover very easily DOWNLOAD THE SPRINT N920P OGD STOCK TARBALL HERE TO RECOVER AND/OR TO RETURN TO OGD STOCK
WORD OF WARNING>>> Once you take the update to OI6 or use the OI6 TAR (get OI6 HERE ) .. YOU CAN NOT GO BACK TO OGD.....
Download ODIN 3.10.7
Download FREEZA's BEASTMODE KERNEL.TAR HERE
DO NOT Download Noble_Kernel_Auto-Root_N920P_v0.1_Alpha.TAR
Download TWRP-2.8.7.0-N920P.TAR
Download BETA-SuperSU-v2.52.ZIP
PREP THE PHONE FIRST ...
go to settings>>>about device>>> scroll to bottom and build number 8 times
now press back button once and tap developer options...
make sure USB debugging is on AND OEM UNLOCK NEEDS TO BE ON ALSO .....
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Place phone in ODIN / Download mode ( press and hold vol down+home+power for a few seconds...then release and press vol up) and plug the phone to the pc....Watch for ID:COM in top left corner to give an ID.......if none is given then check the data cable or try a different one.... NOTE: once you try a flash and "IF" it fails... you will need to disconnect and power off the phone and go back into download mode again or you will get "Setup Connection" hangup error when re-trying to flash
Now Click the "AP" button and in the pop up window, migrate to the KERNEL.TAR and double click it. Wait for it to verify md5 checksum. If bad, re-download the file.(you can download and flash the KERNEL. ZIP in TWRP later)
Now check in the OPTIONS TAB.... make sure ONLY Auto Reboot & F. Reset Time are checked...
uncheck Re-Partition ! ! !
Once these steps are followed, click start and wait till you see PASS in the ID:COM Field
After re-boot, GO BACK INTO DOWNLOAD/ODIN MODE and follow same steps and flash the TWRP.TAR file
(Do not try to boot the phone yet, you will get boot loops.....)
Now install LATEST KERNEL.ZIP & SUPERSU.ZIP in TWRP by going into recovery by powering off the phone then press and hold vol up+home+power until you see the TWRP splash .... (or just install from the market... the market install "may" give update binaries issues... I recommend flashing in TWRP )
I have a SPECIAL HANGOUTS thread for SPRINT NOTE 5 OWNERS.
I would like to add ALL of you to it.
PLEASE PM ME YOUR GMAIL EMAIL ADDRESS SO I CAN ADD YOU
So you have rooted, NOW WHAT? . . . You need to flash the best custom rom > > > >
Galaxy Note 5 OGD Stock Deodexed Rom
@tdunham has built the best deodexed rom.... CLICK HERE FOR HIS THREAD or CLICK this button
This build is based on the stock OGD 5.1.1 Lollipop build.
This is a first release. Even though it has been tested, please report any issues.
Features:
- Rooted
- Busybox
- SQLite
- Hotspot enabled
- Knox Removed
- ItsOn Removed
Download Link ---> N920P_OGD.5.1.1.De-Odexed.Ver1.0.zip
Rom Installation
Preparing the stock rom
• In the stock rom, turn on developer mode, enable USB debugging and OEM Unlock
- Settings>>>about device>>> scroll to bottom and tap build number 8 times
now press back button once and tap developer options...
- Toggle on both USB debugging and OEM Unlock.
• Copy the downloaded rom.zip file to internal storage
Install Custom Recovery with Odin
• Download Odin & custom recovery tar
Odin3_v3.10.6.zip
TWRP-2.8.7.1-Alpha_N920P.tar.md5
or
philz_touch_6.59.0-820876114.tar.md5
• Extract Odin zip-file
• Power down the phone
• Open Odin on pc
• Boot phone in Download Mode (press and hold Home + Power + Volume Down buttons)
• Connect phone and wait until you get a blue sign in Odin
• Add the recovery file to AP / PDA (depending on version of Odin)
• Make sure re-partition & Auto Reboot are NOT ticked
• Click the start button and let the Odin flash complete
• Unplug & Reboot phone directly into Recovery Mode (press and hold Home + Power + Volume Up buttons)
• BACKUP YOUR CURRENT SETUP WITH TWRP
•Do a FULL wipe but do not reboot yet
A full wipe includes:
Dalvik Cache
System
Data
Cache
• Flash rom and reboot.Going back to the Stock Rom
• Use the same Odin instructions to flash TWRP above but using the stock tar
N920PVPU1AOGD_N920PSPT1AOGD_SPR-STOCK_TARBALL
Stock rom mirror download
Credits to my beta testers: @Chaz187 @fsunoles101 @JoeyDuran @GAPO @rlmiller @sml2004
Special Credits to: @tx_dbs_tx
For help with development, the csc & personal mode fixes.
to read about it.
.
.
.
.
.
.
.
thanks for the heads up, but if you haven't yet, you may wanna check the the original dev before mirroring his work. some of them like to track downloads to see how much interest in their work.
Do you guys have an issue updating su binaries?
Sent from my SM-N920P using Tapatalk
ebs512 said:
Do you guys have an issue updating su binaries?
Sent from my SM-N920P using Tapatalk
Click to expand...
Click to collapse
No issues on my end
Sent from my SM-N920P using Tapatalk
Trying now
madsquabbles said:
thanks for the heads up, but if you haven't yet, you may wanna check the the original dev before mirroring his work. some of them like to track downloads to see how much interest in their work.
Click to expand...
Click to collapse
Please do not assume that I haven't reached out to him.
ebs512 said:
Do you guys have an issue updating su binaries?
Sent from my SM-N920P using Tapatalk
Click to expand...
Click to collapse
Try flashing the TWRP.ZIP in recovery if you haven't yet
So I'm assuming this trips knox and disables Samsung pay?
If it does might want to out that in the OP.
DarkManX4lf said:
So I'm assuming this trips knox and disables Samsung pay?
If it does might want to out that in the OP.
Click to expand...
Click to collapse
This is true. It will trip KNOX and disable Samsung Pay.
Will root break the fingerprint sensor or any features other than Samsung Pay??
Sent from my SM-N920P using Tapatalk
Yes fingerprint sensor works. I just used it and it worked no problem.
Is there a way to unroot at the moment ?
DarkManX4lf said:
Is there a way to unroot at the moment ?
Click to expand...
Click to collapse
I would think you can flash the tar file to get back to stock out the box.
travisw0204 said:
I would think you can flash the tar file to get back to stock out the box.
Click to expand...
Click to collapse
Yeah thats the usual way to do it but I can find the stock tar. Its not on Sammobile.
DarkManX4lf said:
Yeah thats the usual way to do it but I can find the stock tar. Its not on Sammobile.
Click to expand...
Click to collapse
I thought Robby had a link for the stock Tar in the Op?
Sent from my SM-N920P using Tapatalk
travisw0204 said:
I thought Robby had a link for the stock Tar in the Op?
Sent from my SM-N920P using Tapatalk
Click to expand...
Click to collapse
Ahh yeah you are right. I just saw that now. The second link worked from OneDrive.
Thanks !
Wifi tether?
Sent from my SM-N910T
ubigred said:
Wifi tether?
Sent from my SM-N910T
Click to expand...
Click to collapse
That works without root by changing the APN
Sent from my SM-N920P using Tapatalk
worked perfect, no issues as of yet.
EDIT:
anyone else getting random reboots? I've had 3 since rooting.
WiFi tether works
Sent from my SM-N920P using XDA Premium HD app
Here Is My Modified Safestrap App To work with Lollipop It is still the safestrap by hashcode for kitkat I just modified it so no kernel flashing is necessary
Change Log:
V17 -updated Safestrap Recovery To V5.01
Should load a little quicker
Added A Reboot To Recovery Button In The Safestrap App For Standalone Use
Features:
No More Flashing Kernels To Enter/Exit Safestrap This Process Is Now Automatic
New Themed And Layout Menu
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Removed Non Working Functions And Rom Slots
SafeStrap Install Zips Will Now Fully Install Safestrap Without Having to Manually Do It With Safestrap Installer
Added New LP Recovery Control Center With Options To Reboot To Safestrap Recovery,Stock Recovery,Bootloader, Or Safe Mode
If You Are Using FlashFire You Now Have The Option To Use FlashFire From The LP Recovery Control Center
Instructions
If you already have safestrap or flashfire installed simply put the Lollipop Safestrap zip on sdcard and flash with either one
If you do not have safestrap or flashfire installed
1. Download this zip and place all 4 apks on your sdcard
2. Install each one
3. Now Open LP Recovery Control App
View attachment 3644238
4.You can now use flashfire to install the Lollipop Safestrap Zip Or You Can Manually Install Safestrap
5. To manually install Safestrap open the LP Recovery Control App
6. Click On Install SafeStrap (ITs The Very Top Option)
View attachment 3644239
7. It may take a bit for the SuperSu Prompt but please wait for it and grant access Then Accept Terms
8. Now click on Install/Update Recovery
View attachment 3644241
9. You will be taking back to the LP Recovery Control App main screen
10. Click On Install SafeStrap and make sure It Says State: Installed If it shows State: Uninstalled Reboot Phone and start from step 5
View attachment 3644243
11. Now you can click the back button to return to LP Recovery Control App
12. To reboot to Safestrap click on Recovery Reboot
13. If for some reason you get stuck on Samsung Screen or go into recovery bootloop.
14 Pull battery reboot to bootloader (Pwr+VolDwn+Home)
15. Plug phone into computer use odin to Flash BOK3 Kernel
16. When Phone reboots start from step 5
17. If you have a failed install or install a zip and it causes bootloop
18. Pull battery reboot to bootloader (Pwr+VolDwn+Home)
19. Plug phone into computer use odin to FlashNI2 Kernel
20. Watch for Safestrap Splash Screen and click to enter safestrap
21. In most cases this will work but if it does not then you may have to start all over and reroot your phone
Downloads
Lollipop_Safestrap_Reboot_Extended_PM_PB1.zip
Lollipop_Safestrap_Only_PB1.zip (For Manual Install)
NI2_stock_kernel.tar.md5 (To enter Safestrap From Bootloop)
Header_Partion_Fix_BOK3.tar.md5 (Use this If Stuck On Samsung Screen)
If you only want the Safestrap app as a stand alone without the Lollipop Control Center
It Has A Rebbot To Recovery Button In The App That Will Take You Straight To Safestrap Recovery
Just Install Like Normal APK
View attachment 3646865
Safestrap-KLTEVZW-5.01.apk
Make Sure These Apks Are Deleted
SafeStrapReboot
Safestrap
LollipopSafeStrap
FlashFire (You Can redownload from play store if you want it)
Thanks
@Hashcode For Safestrap
@klabit87 For Verizon NI2 Flasher
@carl1961 for creating Stock_KERNEL_SafeStrap-Flashable.zip
@benwaffle For Original NI2 Flasher
@Chainfire For Flashfire and SuperSU
saved
It works flawlessly, as always!
Thanks for these!!
@jrkruse think you might be interested in this for the s4. the dev has source on his github.
http://forum.xda-developers.com/showthread.php?t=3311285
Updated twrp3 base
klabit87 said:
@jrkruse think you might be interested in this for the s4. the dev has source on his github.
http://forum.xda-developers.com/showthread.php?t=3311285
Updated twrp3 base
Click to expand...
Click to collapse
I cant get the screen frame rate buffer patches to work
jrkruse said:
I cant get the screen frame rate buffer patches to work
Click to expand...
Click to collapse
Oh ok. Didn't know if you knew about it or not so thought I would bring it up.
Great work though. One guy is gonna do the same thing you have done on our s4
klabit87 said:
Oh ok. Didn't know if you knew about it or not so thought I would bring it up.
Great work though. One guy is gonna do the same thing you have done on our s4
Click to expand...
Click to collapse
Have them PM and I will tell them the process
jrkruse said:
Have them PM and I will tell them the process
Click to expand...
Click to collapse
Ok thanks!
Could we potentially get an update log going in this thread? I find it would be very interesting and useful to know about updates
klabit87 said:
@jrkruse think you might be interested in this for the s4. the dev has source on his github.
http://forum.xda-developers.com/showthread.php?t=3311285
Updated twrp3 base
Click to expand...
Click to collapse
I've been working with mohammad.afaneh over the past few days to get a working updated SS with TWRP 3.0.0-0.
Dudash said:
I've been working with mohammad.afaneh over the past few days to get a working updated SS with TWRP 3.0.0-0.
Click to expand...
Click to collapse
I have been in touch with him also
you are amazing.
wow, that was easy!
jrkuse what would we do without you !?
didn't realize changing the rom didn't affect the apps already installed?
what's the best rom to run? so many to choose from!
I updated with the zip and had to flash the bok3 kernel to get it to reboot.
I was lucky after waiting for the "reboot", the screen went blank for several minutes at this time I pressed the power button and was brought back to ss splash screen which is how I got back to recovery to flash kernel. Not sure what happen. I think it flashed OE1 ss kernel, before I tried the bok3.
Rob684 said:
I updated with the zip and had to flash the bok3 kernel to get it to reboot.
I was lucky after waiting for the "reboot", the screen went blank for several minutes at this time I pressed the power button and was brought back to ss splash screen which is how I got back to recovery to flash kernel. Not sure what happen. I think it flashed OE1 ss kernel, before I tried the bok3.
Click to expand...
Click to collapse
When you flash it for the first time in recovery you still have to flash the kernel to boot back to rom then once you do that it will work. If it doesnt work you need to open install safestrap and manually install it
Thinking about flashing this but had a question. Is there a way to flash a different kernel than the bok3 kernel since it automatically flashes this kernel upon exiting safestrap? That's the only thing holding me back right now. Thanks for this.
capone202 said:
Thinking about flashing this but had a question. Is there a way to flash a different kernel than the bok3 kernel since it automatically flashes this kernel upon exiting safestrap? That's the only thing holding me back right now. Thanks for this.
Click to expand...
Click to collapse
Why you should be running bok3 firmware for everything
Easy peasy.
Thank you for this. Nearly 24 months since this phone's release, and we still have development. Not bad for a "locked down" device.
jrkruse said:
Why you should be running bok3 firmware for everything
Click to expand...
Click to collapse
Its not a big deal, MOAR doesn't seem to be the best with BOK and I was considering going back to BOG5, but I'll probably stick with it and flash this. Thanks for the reply.