I've done everything as instructed. rooted with cydia impactor, recovery with cwm 6.0.1 after 5.8 not working either, and everything runs smoothly until I get to trying to install the rom.
I downloaded the cm11 d2lte nightly and put the zip in the root of my sd card (which is formatted to FAT32 and is designated as my primary) and I cannot get the recovery to mount the sd card.
Also tried formatting the card into exfat to see if that would make a difference, but it didn't either.
Is there anything I'm missing?
luemerian said:
I've done everything as instructed. rooted with cydia impactor, recovery with cwm 6.0.1 after 5.8 not working either, and everything runs smoothly until I get to trying to install the rom.
I downloaded the cm11 d2lte nightly and put the zip in the root of my sd card (which is formatted to FAT32 and is designated as my primary) and I cannot get the recovery to mount the sd card.
Also tried formatting the card into exfat to see if that would make a difference, but it didn't either.
Is there anything I'm missing?
Click to expand...
Click to collapse
I had the same issue when I got a new SD card but with mine formatting it to exfat worked. Just curious why you rooted with cydia impactor on a VZW S3 when nearly everyone else uses towelroot?
Sent from my SCH-I535 using Xparent ICS Tapatalk 2
If only it were verizon.
ShapesBlue said:
I had the same issue when I got a new SD card but with mine formatting it to exfat worked. Just curious why you rooted with cydia impactor on a VZW S3 when nearly everyone else uses towelroot?
Sent from my SCH-I535 using Xparent ICS Tapatalk 2
Click to expand...
Click to collapse
Actually, I'm using a straight talk s3. That's why I used cydia.
luemerian said:
Actually, I'm using a straight talk s3. That's why I used cydia.
Click to expand...
Click to collapse
Ok, you could of used towelroot also. As far as the sdcard issue what brand is it? And is it new?
Sent from my SCH-I535 using Xparent ICS Tapatalk 2
uhhh
ShapesBlue said:
Ok, you could of used towelroot also. As far as the sdcard issue what brand is it? And is it new?
Sent from my SCH-I535 using Xparent ICS Tapatalk 2
Click to expand...
Click to collapse
It's a sandisk, 16gb class 4. It's not new. Been in a couple phones of mine.
luemerian said:
It's a sandisk, 16gb class 4. It's not new. Been in a couple phones of mine.
Click to expand...
Click to collapse
Oh ok. I got a new 64gb one same brand and had to format it in my S3 nearly immediately
Sent from my SCH-I535 using Xparent ICS Tapatalk 2
oyvey
ShapesBlue said:
Oh ok. I got a new 64gb one same brand and had to format it in my S3 nearly immediately
Sent from my SCH-I535 using Xparent ICS Tapatalk 2
Click to expand...
Click to collapse
you think a new card might solve my problem?
luemerian said:
you think a new card might solve my problem?
Click to expand...
Click to collapse
I was just thinking about that myself. I'd suggest a class 10 micro SD card
Sent from my SCH-I535 using Xparent ICS Tapatalk 2
not the card
ShapesBlue said:
I was just thinking about that myself. I'd suggest a class 10 micro SD card
Sent from my SCH-I535 using Xparent ICS Tapatalk 2
Click to expand...
Click to collapse
well, bought a new class 10 micro sd and it made absolutely no difference. I'm thinking it's the recovery I'm using. cwm touch 5.8 and cwm 6.0 are the ones I've tried.
luemerian said:
well, bought a new class 10 micro sd and it made absolutely no difference. I'm thinking it's the recovery I'm using. cwm touch 5.8 and cwm 6.0 are the ones I've tried.
Click to expand...
Click to collapse
Update the recovery also. I forgot to mention that. The SD card will be faster that is the one positive thing
Sent from my SCH-I535 using Xparent ICS Tapatalk 2
AH
luemerian said:
well, bought a new class 10 micro sd and it made absolutely no difference. I'm thinking it's the recovery I'm using. cwm touch 5.8 and cwm 6.0 are the ones I've tried.
Click to expand...
Click to collapse
New Recovery, cwm touch 6.0.4.5 and now it cannot install.
So, I'm going to wipe, reflash stock, reroot, use the new recovery, and see if I cant get somewhere.
Getting a little frustrated.
luemerian said:
New Recovery, cwm touch 6.0.4.5 and now it cannot install.
So, I'm going to wipe, reflash stock, reroot, use the new recovery, and see if I cant get somewhere.
Getting a little frustrated.
Click to expand...
Click to collapse
I know I would get frustrated myself. Try maybe Philz or twrp
Sent from my SCH-I535 using Xparent ICS Tapatalk 2
Related
This is a stock build from Google with ROOT and a few extras for anyone to use as they wish.
Enjoy.
Features
Android OS, 4.1.1 Jellybean build JRO03D
Insecure boot.img
Rooted with the latest superuser
Busybox
Deodexed and Odexed options
Fully Zipaligned
Credits
Google - for Jelly Bean's
Chainfire - For ROOT access
Instructions
Flash via. Custom Recovery
Downloads
Nexus7-JRO03D-DeoDexed-ROOT_4.1.1.signed.zip
Nexus7-JRO03D-Odexed-ROOT_4.1.1.signed.zip
Old Downloads
Nexus7-JRN84D-DeoDexed-ROOT_signed.zip
Nexus7-JRN84D-Odexed-ROOT_signed.zip
More to come
One for the road
Thanks man keep the roms coming
Sent from my KRAKD Nexus 7 using xda app-developers app
Nice work, this will be a great base for anyone who wants to make a stock-based custom rom.
Nice work, I'm surely gonna try .Keep up.
perfect this is what i was looking for!
Hello. On your next 4.1.1 update, can you add Tablet UI?
Thanks
Sent from my SGH-T959
Any word on a 4.1.1 Update to a DeoXed version..
Gunthermic said:
Any word on a 4.1.1 Update to a DeoXed version..
Click to expand...
Click to collapse
Yea will do pretty soon just waiting to get my hands on the tablet again lol. One of the other crew has it.
Sent from my Galaxy Nexus using Tapatalk 2
Thanks! Waiting for 4.1.1 too!
Does anyone know if you flash this does it clear the entire memory or just the os partition. I have flashed many Roms before on other android devices but all those had an SD card and with the unlocking process I know the entire data was erased.
Sent from my Nexus 7 using xda premium
oraclegustavo said:
Does anyone know if you flash this does it clear the entire memory or just the os partition. I have flashed many Roms before on other android devices but all those had an SD card and with the unlocking process I know the entire data was erased.
Sent from my Nexus 7 using xda premium
Click to expand...
Click to collapse
It won't erase your SD card
Sent from my Galaxy Nexus using Tapatalk 2
CdTDroiD said:
It won't erase your SD card
Sent from my Galaxy Nexus using Tapatalk 2
Click to expand...
Click to collapse
ok, thanks. Now I tried downloading both versions and installing via clockwork mod and it aborts. Saying status 0. Any ideas?
oraclegustavo said:
ok, thanks. Now I tried downloading both versions and installing via clockwork mod and it aborts. Saying status 0. Any ideas?
Click to expand...
Click to collapse
Ah OK I'll have a look into it tonight for you, its probably the updater script if you want you can try use the META folder from another ROM (nexus 7 ROM) and see if it flashes until I fix it later
Sent from my Galaxy Nexus using Tapatalk 2
Yup looks like I'll be waiting because I have absolutely no idea what you just said
Sent from my Nexus 7 using xda premium
Hahaha probably best then
Sent from my Galaxy Nexus using Tapatalk 2
It appears it not just your downloads I can't seem to flash any Roms. I tried to flash other ROM and it keeps giving me same error. It almost seems like it can find the zip files on SD card to flash and then it goes to flash and can no longer find the file. Anyone have any insight into this?
first off seems D/L is not working but I dint think there were so many issues with ROM. We definetly need a solid Stock ROM with ROOT (4.1.1), Hope its works when I flash
is this completely stock? no tablet UI dpi build.prop changes? (that's what i'm after)
ace9988 said:
is this completely stock? no tablet UI dpi build.prop changes? (that's what i'm after)
Click to expand...
Click to collapse
Yes that's right
Sent from my Galaxy Nexus using Tapatalk 2
For use with Heimdall:
Normal 6.0.2.9: recovery-clockwork-6.0.2.9-i9305.img
Touch 6.0.2.9: recovery-clockwork-touch-6.0.2.9-i9305.img
For use with Odin:
Touch 6.0.2.9: GT-I9305_ClockworkMod-Recovery-Touch_6.0.2.9.tar - 6.04 MB
Official ClockworkMod download page: http://clockworkmod.com/rommanager
ROM Download section: http://clockworkmod.com/rommanager/developers/i9305?name=Samsung Galaxy S3 LTE (GT-I9305)
ClockworkMod Recovery 6.X
This version is there? backup/restore EFS in both tar + img formats！
Kinda odd that @codeworkx posted a cwm recovery her, but nice. Mabey you can give some CM love on the GT-I9305??
AW: [RECOVERY][GT-I9305] ClockworkMod Recovery 6.X
stian230 said:
Kinda odd that @codeworkx posted a cwm recovery her, but nice. Mabey you can give some CM love on the GT-I9305??
Click to expand...
Click to collapse
Did you sleept the two last days?
Sent from my GT-I9305 using xda app-developers app
Bulkatos said:
Did you sleept the two last days?
Sent from my GT-I9305 using xda app-developers app
Click to expand...
Click to collapse
Please tell me what going on! Is codeworkx porting cm?
Edit : found it and downloading now..
stian230 said:
Please tell me what going on! Is codeworkx porting cm?
Edit : found it and downloading now..
Click to expand...
Click to collapse
Since you didn't explain after finding it: no, codeworkx is not porting, he has ported and now it is up to us to complete it. A lot of props go out to him for getting us started!
Re: [RECOVERY][GT-I9305] ClockworkMod Recovery 6.X
Awesome. But I am getting cannot mount ext sd card.
Sent from my GT-I9305 using Tapatalk 2
Re: [RECOVERY][GT-I9305] ClockworkMod Recovery 6.X
Any feedback on issues?
Sent from my GT-I9305 using Tapatalk 2
yep I am getting the same. Tried everything.
formatted the card using fat32 with a 32kb cluster.
switched back to cwm 5 everything was fine. It has to be CWM 6.
I am using a 64GB Sandisk class 10 micro sd card
bleepsake said:
yep I am getting the same. Tried everything.
formatted the card using fat32 with a 32kb cluster.
switched back to cwm 5 everything was fine. It has to be CWM 6.
I am using a 64GB Sandisk class 10 micro sd card
Click to expand...
Click to collapse
Same card, using FAT32 on an MBR disk label. Working fine here. 1024kb block size, not that that has any effect on it working or not.
Re: [RECOVERY][GT-I9305] ClockworkMod Recovery 6.X
Same card also. Tried a few things with no luck. It works fine with Recovery v5.
Sent from my GT-I9305 using Tapatalk 2
Re: [RECOVERY][GT-I9305] ClockworkMod Recovery 6.X
Is this the wrong place to be asking for help?
Sent from my GT-I9305 using Tapatalk 2
Re: [RECOVERY][GT-I9305] ClockworkMod Recovery 6.X
Zzzzzzzzzzzzzzzzzz
Sent from my GT-I9305 using Tapatalk 2
AW: [RECOVERY][GT-I9305] ClockworkMod Recovery 6.X
oias.heeda said:
Same card also. Tried a few things with no luck. It works fine with Recovery v5.
Sent from my GT-I9305 using Tapatalk 2
Click to expand...
Click to collapse
What exactly have you tried?
How do you format the Card?
Have you taken a cardreader and set the clustersize to default and the Filesystem to FAT32?
----------------------------------------------
Gesendet von meinem GT-I9305
ROM: | Pandoriam v6.5 | Kernel: | Perseus a31.2 |
Don't say thanks, hit Thanks!
----------------------------------------------
anybuddy said:
What exactly have you tried?
How do you format the Card?
Have you taken a cardreader and set the clustersize to default and the Filesystem to FAT32?
----------------------------------------------
Gesendet von meinem GT-I9305
ROM: | Pandoriam v6.5 | Kernel: | Perseus a31.2 |
Don't say thanks, hit Thanks!
----------------------------------------------
Click to expand...
Click to collapse
Formatted 64gb sd on PC. Used FAT32 32kb cluster.
Still getting same issue.
oias.heeda said:
Formatted 64gb sd on PC. Used FAT32 32kb cluster.
Still getting same issue.
Click to expand...
Click to collapse
Have you tried with another card, to eliminate the fact that it could just be that specific card and not the recovery?
Re: [RECOVERY][GT-I9305] ClockworkMod Recovery 6.X
I will try that, it's a brand new card though.
Sent from my GT-I9305 using Tapatalk 2
AW: [RECOVERY][GT-I9305] ClockworkMod Recovery 6.X
oias.heeda said:
Formatted 64gb sd on PC. Used FAT32 32kb cluster.
Still getting same issue.
Click to expand...
Click to collapse
Don't know if you use a cardreader or just put the phone on PC, but please try a cardreader and a clustersize under 4 KB f.e. 2048 Byte.
----------------------------------------------
Gesendet von meinem GT-I9305
ROM: | Pandoriam v6.5 | Kernel: | Perseus a31.2 |
Don't say thanks, hit Thanks!
----------------------------------------------
Re: [RECOVERY][GT-I9305] ClockworkMod Recovery 6.X
oias.heeda said:
Formatted 64gb sd on PC. Used FAT32 32kb cluster.
Still getting same issue.
Click to expand...
Click to collapse
Put in s2 which running ics, format sd card, once completed, your card will be formatted to fat32. But when s2 running samsung jb, it will format your card to exFAT. After formatted to fat32, all the problems solved. Used pc to format this 64gb card to fat32, you need a special formatter, else it will ended became a 32gb card.
Cwm recovery and mobile odin not supporting exFAT. FAT32 more compatible to program in our phone but you lose out the speed offer by exFAT. exFAT when using in my s2 in usb mode, it read/write was fast. Eg when usb to pc, I can get 10mb/s under exFAT but only 4mb/s on fat32.
Sent from my GT-P5100 using xda premium
Re: [RECOVERY][GT-I9305] ClockworkMod Recovery 6.X
Hey guys. Did what you suggested still with no luck. Thanks all for your help. I am swapping to twrp recovery. Already installed with exfat and no issues. Thanks again.
Sent from my GT-I9305 using Tapatalk 2
Well I'm New To This I'm Trying To Port Over CWM6 to the Galaxy Tab 3 7"
I'm Just Getting Started I'm Downloading Androids Source And Trying To Download CyanogenMod 10 Source
Once Done I'm Working On Building CWM for The Galaxy Tab 3 7"
I'm kinda dreaming on doing the same but I'm a noob.... I just have basic java concepts and I'm just slowly getting into this development thing but anything I can help just tell me I dunno, uploading, graphic design, buying you popcorn etc
Sent from my SM-T210 using xda premium
Still working on it
I haven't forgot about it but its kinda hard I'm new to this
Lots of reading.........traveling the same path friend
Sent from my SM-T210R using XDA Premium 4 mobile app
Zidkijah said:
Lots of reading.........traveling the same path friend
Sent from my SM-T210R using XDA Premium 4 mobile app
Click to expand...
Click to collapse
i just need the boot.img im trying to extract it its hard work been at it for hours
Just pull the stock firmware and pull it from there........ sammobile.com/firmwares
Sent from my SCH-I535 using XDA Premium 4 mobile app
Deleted.
Found the solution
awesome
thanks
There's already a non cwm or twrp recovery working, maybe that will help
I made a CWM recovery and root.zip for the 10.1 version
In dev section
DutchDanny said:
I made a CWM recovery and root.zip for the 10.1 version
In dev section
Click to expand...
Click to collapse
Root and CWM are ready for the SM-T210
DutchDanny said:
I made a CWM recovery and root.zip for the 10.1 version
In dev section
Click to expand...
Click to collapse
Yes, but I tried to do it and I'm having issues. I've got your recovery working, but it says that it can't mount my sd card. I can't flash the root zip. I'm sorry that I have to post this here, but I'm new to this forum and it seems as though my hands are tied. I can't post in the developer's section, and I can't send PMs to a lot of people because I don't have 10 posts yet. I do appreciate the hard work, and I do donate to developers. Maybe I'm doing something wrong, but I don't think so. I just wanted to bring it to your attention.
Put root.zip on sd when tab is running Android, then when in cwm you can flash it
Send via my BinDroided HTC ONE
Would it work for SM-T310 8.0? If not, is it possible to make it compatible?
You would have ro build it from source, having a stock boot.img and stock recovery.img with some knowledge about linux is all you need
8" has a cwm afaik
Send via my BinDroided HTC ONE
DutchDanny said:
Put root.zip on sd when tab is running Android, then when in cwm you can flash it
Send via my BinDroided HTC ONE
Click to expand...
Click to collapse
I don't know what you mean. The tablet is only running Android... No matter, I figured it out. Your custom CWM doesn't recognize 64G sd cards. I managed to find a 64mb sd card I had laying about & I put the zip on that. It did the trick. Thanks for making a root for this tablet. I'll send you a donation soon.
Mortician607 said:
I don't know what you mean. The tablet is only running Android... No matter, I figured it out. Your custom CWM doesn't recognize 64G sd cards. I managed to find a 64mb sd card I had laying about & I put the zip on that. It did the trick. Thanks for making a root for this tablet. I'll send you a donation soon.
Click to expand...
Click to collapse
I don't think it's "my" cwm doesn't recognize your 64 gig card, but cwm in general doesn't do that
Send via my BinDroided HTC ONE
is this applicable for SM-T210? i want to root my tab 3 via cwm coz i dont want to flash another firmware on my tab and i want to stick on my stock firmware. is this even possible?
I've never used a phone without a microsd card. It's pretty useful to be able to flash a rom from a microsd so that you don't need to keep your working copies on the device all the time... they take up alot of space.
Do any of the custom recoveries support reading off of a microsd card reader?
TWRP supports USB-OTG. I'm not sure about CWM though as I haven't used it for a few months now.
iPWNtehNOOB said:
TWRP supports USB-OTG. I'm not sure about CWM though as I haven't used it for a few months now.
Click to expand...
Click to collapse
thank you
Philz recovery Supports OTG
Sent from my Nexus 5 using Tapatalk
rootSU said:
Philz recovery Supports OTG
Sent from my Nexus 5 using Tapatalk
Click to expand...
Click to collapse
This is great to know, cause i just flash that Kernel...
Enviado desde mi I9100 Miui Rom V5 4.3.14 vía TapaTalk.
Its a recovery. Not related to kernel
Sent from my Nexus 5 using Tapatalk
Hi everyone. I was on 4.1.2 with SynergyRom, then flashed I545VRUDMI1_modem in preparation for trying to flash AllianceRom per Dev's instructions. Now apparently I have a hard brick, no response trying to boot or anything. Any suggestions for proceeding? I am a bit rusty at flashing and may not have quite understood the transition from 4.1.2. Thanks,
If you flash that on a galaxy s3 the result will always be a hard brick. That modem is for a galaxy s4
Sent from my SCH-I535 using xda app-developers app
^^^Yup. The i545 is the S4. I'm not sure if just overwriting the modem partition itself would result in a hard brick, but I'm assuming the two phones have different partition tables so you most likely have a paper weight. You could try the SD unbrick method.
This may help..
I just wrote a boot img to a 16gb(my phones storage size)and inserted it to my phone and it booted. I was hard bricked s3 vzw 4.3.
Doh
Thanks, I did not read close enough. Ordered a 32 GB card for this weekend and hoping I can at least get up and running,
Ok hope it works.
Sent from my SCH-I535 using Tapatalk
1adam12ks said:
Thanks, I did not read close enough. Ordered a 32 GB card for this weekend and hoping I can at least get up and running,
Click to expand...
Click to collapse
Did it work?
Sent from my SCH-I535 using Tapatalk
Nope had to get help JTAG to 4.3 just glad phone is repaired.
Sent from my SCH-I535 using Tapatalk
Ok glad your e back up.
Sent from my SCH-I535 using Tapatalk