I am currently using a XT926 with stock KitKat (unlocked/unrooted) and have a kernel version of 3.4.42. I read that 3.4 kernel wouldn't work with PA, but a 3.0 would. What steps would I need to take to have the correct kernel running as to not mess up my phone?
oFumbleSo said:
I am currently using a XT926 with stock KitKat (unlocked/unrooted) and have a kernel version of 3.4.42. I read that 3.4 kernel wouldn't work with PA, but a 3.0 would. What steps would I need to take to have the correct kernel running as to not mess up my phone?
Click to expand...
Click to collapse
you have to downgrade to JB for that.. because the 3.0 kernel just work with Jelly Bean Bootloader..
Related
Hi,
I have installed Matr1x kernel. I am using Stock ICS Rom only. Will the New Jelly Bean Update.zip work.
Can i install using cwm.
Please advise me.
Regards,
asdf2020
It should flash through CWM, but keep in mind it'll overwrite your recovery and replace your kernel.
chronophase1 said:
It should flash through CWM, but keep in mind it'll overwrite your recovery and replace your kernel.
Click to expand...
Click to collapse
Thanks for reply.
Does it will wipe my data/apps as well?
No. Everything will be the same. I flashed over ICS and everything was kept the same for me
chronophase1 said:
No. Everything will be the same. I flashed over ICS and everything was kept the same for me
Click to expand...
Click to collapse
has your kernel been replaced??? or is it the same ??
For ****s-and-giggles, I threw the matr1x kernel on top of my 4.1.1 ota last night ... It didn't work.
asdf2020 said:
has your kernel been replaced??? or is it the same ??
Click to expand...
Click to collapse
Yea. My app settings stayed the same, but like I said, my kernel got replaced, which is expected. I don't use matrix though and seeing as the kernel sources vary, chances of it working are pretty slim, as seen above.
asdf2020 said:
Hi,
I have installed Matr1x kernel. I am using Stock ICS Rom only. Will the New Jelly Bean Update.zip work.
Can i install using cwm.
Please advise me.
Regards,
asdf2020
Click to expand...
Click to collapse
Your kernel will get replaced. I wouldn't recommend it because I've tried other kernels with the official OTA JB ROM and the experience wasn't as smooth. I have yet to try Matr1x kernel yet though.
No different versión of Ndroid not supported at least yet ;D
Lets just say hes workin on it i would expect
So......official JB 4.1 won't work on my Matr1x kernel
What roms have you guys gotten running on the lg phoenix/ P505 with the joban kernel
thugnastie said:
What roms have you guys gotten running on the lg phoenix/ P505 with the joban kernel
Click to expand...
Click to collapse
About your question, i got running on my lg thrive, which is identical in hardware to the lg phoenix; gingersnap, gingerdx, gtr, cyanogen mod 7.2,, only that ones...
Currently joban's kernel is only supported in gingerbread, even in those roms is kind of unstable...
Now, we have a new kernel from the great developer DJnoXd, it supports Ice Cream Sandwich, and Jellybean... But if you are only interested in Gingerbread, tell me and i will pm you a better method to get roms
DJnoXd kernel will work on GB also. Arjen has a kernel that will work on GB too.
joban kernel is old base band... so any p500 rom that is obb will work.
savagephoenix said:
DJnoXd kernel will work on GB also. Arjen has a kernel that will work on GB too.
joban kernel is old base band... so any p500 rom that is obb will work.
Click to expand...
Click to collapse
can you give me the link to the rom and kernel your useing
Do I flash the rom then the kernel right after or do I flash the rom, boot up the phone then go back into recovery to flash the kernel
Just figured out djnoxd kernel no good for gb. Found in original development here on xda
Arjens is found at androidcentral under Phoenix / thrive thread
Sorry no links .. on phone.
Flash rom. Reboot recovery. Flash kernel. Recamend full boot. Then flash gapps. But can flash gapps after kernel
iirc I just read the new kernel runs on the p500/505/509, I don't know which one is the phoenix tho
Sent from my LG-P500 using xda app-developers app
i believe that to be the new 3.0 kernel
so no one could give me links
http://forum.xda-developers.com/showthread.php?t=1587209 DJNoXD ICS and 4.1.x
http://forum.xda-developers.com/showthread.php?t=2144790 3.0 kernel by androidarmv6 team maybe ICS primarily for 4.1.x & 4.2.x
http://forum.xda-developers.com/showthread.php?t=2140930 sweetnsour i think still in beta, primarily for ICS, may work on JB
http://forums.androidcentral.com/t-...gerbread-cm-2-6-35-kernel-thrive-phoenix.html Arjens GB kernel
dont be lazy. do read the OP and make sure you know what your doing.
I am running CM 10.1 nightly on my d2vzw and I just want to make sure that this kernel would wouldn't brick my phone. Thanks
http://forum.xda-developers.com/showthread.php?t=2226894
uromastix87 said:
I am running CM 10.1 nightly on my d2vzw and I just want to make sure that this kernel would wouldn't brick my phone. Thanks
http://forum.xda-developers.com/showthread.php?t=2226894
Click to expand...
Click to collapse
It is a silly question only because you're asking if a kernel meant for this device and for the type of ROM you're running will work. Since you're using 10.1 nightly use the 3.4 version of the kernel. FYI all AOSP kernels will work with your ROM since they have 3.4 versions for Android 4.2.2 and please know the difference between a software brick and a hardware brick. Enjoy your ROM.
are there any new kernels or older kernels that will work with the 4.2 bootlader and the latest .27 firmware? i just finally updated from 4.1 bootloader to 4.2 and latest firmware. did this so i could update cm10.1 from a old june version i had to the latest and greatest 10.2 . on my old setup i ran perf kernel. does anyone know of any kernels i can run on new setup?
Are you looking for a kernel for .27 firmware or a kernel for CM10.2?
hardslog said:
Are you looking for a kernel for .27 firmware or a kernel for CM10.2?
Click to expand...
Click to collapse
more for cm10.2 does perf kenel still work?
No, perf kernel is not working anymore. Hasn't for a while.
I have been able to get some stock based kernels modified for CM10.1, one of them has overclocking abilities too. As for CM10.2, right now you are out of luck, as builds for it are still so new.
Sbdags has O/C kernels that work with CROMI, but those are all stock based.
hardslog said:
No, perf kernel is not working anymore. Hasn't for a while.
I have been able to get some stock based kernels modified for CM10.1, one of them has overclocking abilities too. As for CM10.2, right now you are out of luck, as builds for it are still so new.
Sbdags has O/C kernels that work with CROMI, but those are all stock based.
Click to expand...
Click to collapse
Ya sucks I was happy with perfect and cm10.1 but of course cm force me to update as it wasn't supporting new 4.1 bootloader anymore. I figured if I was going to do it I'd go big. IL just wait it out. Cm 10.2 is running OK with exception of gas issue.
Sent from inside my mkv.
I got Hundsbuah's kernel working in CM10.1 with O/C
hardslog said:
I got Hundsbuah's kernel working in CM10.1 with O/C
Click to expand...
Click to collapse
Good ****. Let me know if you need testers on 10.2
Sent from inside my mkv.
any body have try PA 4.2 Beta 4 and combine with furnace kernel, im having trouble here after flashing furnace kernel i stuck at lg logo does anyone know how to solve this? i really like this kernel
Goodsdept said:
any body have try PA 4.2 Beta 4 and combine with furnace kernel, im having trouble here after flashing furnace kernel i stuck at lg logo does anyone know how to solve this? i really like this kernel
Click to expand...
Click to collapse
PA 4.2 is an Android 4.4 (kitkat) ROM. Furnace Kernel only works with JellyBean based roms. This combo will not work no matter what you do.
If you use a KitKat ROM, you need to use a KitKat kernel. If you want a JellyBean Kernel (ie Furnace Kernel), look for a JellyBean ROM.
do you have any sugestion custom kernel? Im having problem using stock PA kernel
Goodsdept said:
do you have any sugestion custom kernel? Im having problem using stock PA kernel
Click to expand...
Click to collapse
What problems are you having with the stock PA kernel? Are you sure they are not ROM or APK bugs?
I usually stick with stock kernels and report to the dev issues I'm having. Often any issues I am having are either common issues and somebody found a solution (like using an older version of a particular APK) or are problems that are new to me (based on my config like using a govenor that is buggy with that particular ROM).
The biggest issues I have seen with things are often with the init.d scripts OR with using conflicting software (2 different CPU controllers for example).
If you are having FC's, I'd post a logcat in the forum thread along with any relevant data. If it just seems buggy, post the bugs in the forum thread along with steps to reproduce it. If it is a kitkat rom you are running, are you using DALVIK or ART? I know ART is still in testing and does not play nice with some things like xposed framework.