Hi to all. I am new in the site. I have bought the following Tablet. I have a problem, when you touch the screen, the actual click is 2 cm away from the place you press. I tried to calibrate the G Sensor (because it neither rolls) but it crashes when you press calibrate.
I can´t use the table, as you can figure out. I tried two apk's to calibrate it (with a lot of effort since I can´t even configure the wifi because I can´t use the whole keyboard), but with no success.
Thanks in advance.
Details of the Tablet (chinese and unbranded):
General
Operating System
Android 4.2
CPU
ATM7021A Dual Core
GPU
PowerVR SGX 540
Processor Speed
1.3GHz
RAM
1G DDR3
Hard Drive Capacity
8GB
Extended Memory
Support external TF card extend up to 32GB
Gravity Sensor
Yes, 4-dimensional G-sensor
Flash Player
Support Adobe Flash 11.0
Display
Display Size
10.1 Inch
Display Technology
TFT LCD Capacitive Touch Screen
Multi-Touch
Yes, 10 Points
Display Resolution
1024 x 600 pixels
Hi, I know that it's a post long time ago.
To fix your problem, you either send your tablet back to where you buy it OR you will have to look for a proper firmware for your tablet and flash it.
If you can provide more information of the tablet such as build number, screen size, and resolution. Then, I will be able to help you find the correct firmware. Thanks.
Related
I recently bought a Google Android tablet off of eBay and I am a little disappointed that it is running Android 2.2 Froyo. I have a T-Mobile LG G2X, which I have rooted and installed CM7 on with GB, but I have never owned a tablet before and am rather at a loss.
I would like to root and upgrade, possibly flash CM7 onto the tablet if I can but I have no clue where to start nor do I know if this is even possible. Any help, tips, hints or tricks will be greatly appreciated. Thank you so much
Specifications (because it would not let me add a link yet)
Processor: VIA MW8650 High-performance 800MHZ CPU+300MHZ DSP
Frequency: 800Mhz
OS: Google Android 2.2
Memory RAM: 256MB
Flash Memory: 2GB (1GB Free) (Expandable by MicroSD to 32GB)
WiFi: 802.11 b / g
3G Function:
- TD-CDMA:TD368
- WCDMA:Huawei E220/E230/E160X/E169G/E1750
- Alcatel X060S/X200
Speaker: Built-in Speaker 8/1W
Camera: Built-in 0.3MP
Reset hole: Hidden (reset function)
Buttons:
- Top of the key: Power Key
- Positive primary key: ESC
- Right button Volume control Keys + Menu button
Display Resolution: WVGA 800 x 480 Pixel
Size: 8 inch TFT 4:3
Touch Screen: TFT Resistive Touch Screen (two point touch),achieve pages and images zoom in and out
Card Reader Slot: T-flash card (Support up to 32GB)
Sound effect: - In focus Audio
- Built-in stereo speaker
- Built-in Microphone
Media File Audio: MP3,WMA,WAV,AAC
Video: [MPEG1/2/4,MJPG,H263](1280×720) resolution,H264 (720 × 480) resolution.
Battery: 2500mAh, 7.4V
Gravity Sensor: 4-Dimensional gravity sensor
Battery Life - Standby time: above 10 hours - Video play: 3 hours
I'm sorry to tell you, but those chinatablets have very little community support.
Edit: for rooting I think most generic methods of rooting are usable.
Hi,
is possible to install stock Android 3 or ICS on Grid 10? If yes, could you help me with this ?
Stock system is based on android GridOS and is really bad and no more supported;/
below details:
Specifications (base version)
Manufacturer
Fusion Garage
Model name
Grid 10
CPU type
Nvidia Tegra2 (Dual Cortex A9)
CPU speed
1200 Mhz
Graphics
Nvidia ULP GeForce
OS
Grid
Display Size
10.1" 1366 X 768
Screen Type
LED-Backlit LCD
Touch Technology
Capacitive Multi-touch
Display Type
Soft (Finger) Touch
RAM
512 MB
Flash
16 GB
Keyboard
NO
Mouse Pointer
NO
Battery capacity
21.5 (Wh)
Weight
960gm / 33.9 oz.
Size (w/h/d mm)
122/64/10 mm
Size (w/h/d inches)
4.8/2.5/0.4
Physical Interfaces
Docking connector
Line-out / Headphone (3.5mm)
Wireless Interfaces
802.11 b/g/n
BT 2.1
HSDPA
Additional Specs and Accessories (can vary)
3G voice/data modem
A-GPS (Internet Assisted)
Accelerometer
Ambient light sensor
Capacitive Touchscreen
Gyroscope
Microphone
Mono speaker
WebCam 1.3Mp
Thanks for help !!
my-tablet specs
Processor - Cortex A8 RK2906 1Ghz
Ram - 512mb DDR3
display 7''
res: 800x480
touch: capacitive 5 point multitouch
wifi: 802,11b//n
dual cam: front 0.3mp, rear 2mp
default os :4.0.4
i installed 4.1.1 from the link... http://forum.xda-developers.com/showthread.php?t=2112562
it installed successfully with no errors...
after installation. i found that the touch is functioning reverse. i.e (in landscape mode when i press on charging icon, back icon is triggered)
is there an app or somekind of fix for this problem?
Review Video:
Specs:
5.5" inch capacitive 2-Point Multi Touch Screen
Display 720x1280 pixel resolution - Full HD Display, IPS
MTK6580 32-Bit Quad-Core [email protected] 1.3GHz
GPU: Mali-400 MP
Android 5.1 Lollipop
1GB RAM / 8GB of internal memory - TF-card support
Quadband, unlocked, 3G / UMTS / HSDPA+ / WCDMA
Wifi, Bluetooth, GPS, A-GPS, g-sensor, proximity sensor, light sensor
OTG - USB on the go / Firmware updates over the air
Off-Screen gestures / Air gestures
Removable 2500mAh battery
Main camera: 13 MP output (8MP real?), auto focus, dual LED flash, F2.0
Front camera: 5MP output (2MP real), LED flash, F2.8
Dual Sim - Dual Standby (two micro sim cards)
Weight: 180 g / 8,7 mm thick
Camera sample pictures on my blog: http://colonelzap.blogspot.de/2016/02/umi-rome-x-video-review-mt6580-60-phone.html
My Unboxing (Italian Language)
My TWRP also available:
http://www.needrom.com/download/twrp-megthebest/
Strange Rome X behaviour
I've got a Rome X, but I'm struggling with something. It doesn't run background services at startup, or leave them running if you swipe to kill the app.
For example, I installed GSam Battery Monitor - when that app is running there is a notification showing battery left. This does not appear when the phone is rebooted - only appearing when I launch the app. If I then swipe right to kill the app, the notification disappears. This doesn't happen on any other Android device I have.
Does anyone have any ideas? Anyone have the same issue? Anything I can tweak if the phone is rooted?
Is there a recovery like TWRP or CWM for it?
Hi,
I recently bought a Tolino Tab 8 with a Intel Atom Z3735 processor, running on KitKat 4.4.4. Everthing works fine but every time i switch between apps the screen brightness changes depending on the background of the app e.g. when i open twitter (mostly white background) the screen brightness goes up and when i go back to the home screen (black background) the brightness goes down. No matter if i enabled auto dimming in the settings or not. I've read that has something to do with Intels Display Power Saving Technology which is used to extend the battery life of the tab. I tried to edit the build.prop (mentioned here http://forum.xda-developers.com/showpost.php?p=65422943&postcount=1786 ) to turn it off but nothing worked so far. I also tried to find the driver settings itself ( mentioned here https://forums.lenovo.com/t5/Lenovo...Tab-S8-50-Screen-Dimming-Problem/td-p/1873040 ) but could'nt find the right settings.
The Tablet was manufactured by Trekstor if this matters somehow.
Hope you guys can help me to solve it.
I also have a minor bug where i can't change video resolution in the youtube app above 720p even the Display has the resolution of 1920x1200 which i think has something to do with 4.4.4.