Database Info

bootloader mode and i can't flash with another rom

Hello
i tried to flash my prophet with a portuguese rom with wm6
Now prophet is in bootloader mode and i can't do nothing
what can i do?
i tried
NVID_RUU
and it doesn't update

Go back to a WM5 Rom.

i already done that
but i still can't update for a rom with wm6
i have
ipl 2.15
and
spl 2.20
it's a g4

You must read about SoftSPL or HardSPL - Than you can flash a WM6 Rom.

How to do
1. Instala a Rom original do teu aparelho existe o link ai no site.
2. Faz um update a rom com a do pda mobiz (updaterom) é o nome do ficheiro.
3. Faz o hardspl g3, é o mais habitual mas vê no teu aparelho.
4. Instala a nova rom com a g3 ou g4 (RUU) update utility.
Se tiveres dúvidas diz ok, um abraço.

deltav13 said:
1. Instala a Rom original do teu aparelho existe o link ai no site.
2. Faz um update a rom com a do pda mobiz (updaterom) é o nome do ficheiro.
3. Faz o hardspl g3, é o mais habitual mas vê no teu aparelho.
4. Instala a nova rom com a g3 ou g4 (RUU) update utility.
Se tiveres dúvidas diz ok, um abraço.
Click to expand...
Click to collapse
can you write / translate this in english please ?
I have the same problem with my prophet and need some instructions to flash
thx in advance

How to do
Charge your device for 2 hours first.
Second enter boot loader mode 3 colours by pressing the com button on the left side of the device, wait.
1. Install the original rom
2. Do a update rom use pda MOBIZ STEP 2 update rom file wait...
3. After do a hard spl G3 or G4 depends on your device.
4. Wait until the device enters again into boot loader mode.
5. Install the new Rom and wait for the device to reeboot.
6 If all goes well you can now use WM6.

i already solve this
thanks to all

deltav13 said:
Charge your device for 2 hours first.
Second enter boot loader mode 3 colours by pressing the com button on the left side of the device, wait.
1. Install the original rom
2. Do a update rom use pda MOBIZ STEP 2 update rom file wait...
3. After do a hard spl G3 or G4 depends on your device.
4. Wait until the device enters again into boot loader mode.
5. Install the new Rom and wait for the device to reeboot.
6 If all goes well you can now use WM6.
Click to expand...
Click to collapse
OK, my problem is bigger than this. I can get to the CMONEX page but no further; just hangs there. ALSO, active sync won't connect; tries to but gives up.
The problem? I installed a custom ROM off ppcgeeks.com; it seemed to work well, then it started doing funny things, like not allowing me to access pages; giving me errors messages, etc. I did a soft reset; it hung on the 1st page showing Touch Diamond. Also, won't sync. Did a hard reset (the only way that works for me is to soft reset, quickly press power + vol down while flipping the phone over until the Cmonex page comes up).
Phone hangs there; can't sync it with PC (xppro) anymore (no problems before).
QUESTION: is my phone effed?

HELP! Error 00018003 when flashing to 6.5 (23017)!

Edit: I resolved it by sifting through the forum and using Task 2a

Erro ao Instalar Windows Mobile
Treo 750
Ja tentei instalar varias Roms de Windows Mobile o fone da boot normal mas
nao termina nehuma das instalaçoes termina com o Erro 00018003 ou se estou tentando outra Rom ele para com erro na EXTROM como resolvo isso, preciso fazer meu treo funcionar novamente
BOOT:
CHEE100
IPL-0.20
CHEE100
SPL-1.40 OLINEX
SOCORROO...HELP....

English please! Can't help if we cant understand

HELP!I have the same problem: Error 00018003...
I upgraded from windows 6.1 to 6.5 bun 6.5 wouldn'y work because it expires in 2010. Than I upgraded to 6.5.1 ROM and I got update failure at approx 80%. From then I can't install OS in my Treo neither from the memory stick nor computer. The phone enters in Bootleader mode. I keep getting the error message when I want to update. Please post a solution. Thanks!

Hi....I solve this problem...ERROR 00018003
I fix my phone..Excuse my bad english..I live in ROMANIA...Follow this step to fix phone:download MTTY 1.42.exe...instal driver....connect you phone in bootloader mode...run MTTY.exe...select USB...press ENTER...type :"task 2a"....wait to finish operation MTTY(aprox 10min.)......disconect your phone...put the sdcard with CHEEIMG.nbh file in your phone...reset phone...wait 2-3 sec...press power button...an wait to finish upgrade...in screen will appear "upgrade succes"...reset phone....Good luck!

ok
Sucsses treo live

bigwolfcrazywolf said:
I fix my phone..Excuse my bad english..I live in ROMANIA...Follow this step to fix phone:download MTTY 1.42.exe...instal driver....connect you phone in bootloader mode...run MTTY.exe...select USB...press ENTER...type :"task 2a"....wait to finish operation MTTY(aprox 10min.)......disconect your phone...put the sdcard with CHEEIMG.nbh file in your phone...reset phone...wait 2-3 sec...press power button...an wait to finish upgrade...in screen will appear "upgrade succes"...reset phone....Good luck!
Click to expand...
Click to collapse
where do i find the driver?
im not getting a usb> prompt???

Hmm, for those who want to avoid problems in the future, I'll provide some tips from experience:
-When flashing a Custom ROM, it's always best to start from an official Palm WM6 ROM (unless stated otherwise), the same goes for when you flash a Custom ROM over another. Especially Veisen's WM6.5, it's been known to give downgraders a hard time removing his ROM. I myself ran into weird problems simply from going WM6.1 to a custom, radio-less WM6.
-Going all the way back to WM5 works too, mostly for nostalgia lol...
-Of course, the general rule of ROM flashing is to clear data immediately after flashing any ROM whatsoever.

Driver USB
step1 windows xp
step2 Active Sync 4.2
step3 conectar o phone ao pc
step4 colocar o Active sync para procurar o treo
step5 no mtty1 port usb deve aparecer foi assim que consegui

Hello to all tilt kaiser's fan
im trying to go back from android to original stock rom of cingular and on the update from the sd i get :
Radio -ok
bootloader -ok
splash -ok
os -fail
00018003
update terminate
update fail
to go back to android i cant
now im realy stuck, what to do ?????
I want my tilt alive again

[HTC Herald][EN\PL]I can not install ROM / Nie moge zainstalować ROMu

[Sorry for my English, I use google translator]
Hello
After the last ROM I had a problem with the inclusion of PDA so I made HR but HR at boot instead of the logo has a green screen. That I decided to install the ROM with the memory card but can not detect the file only once HERAIMG.nbh flies to
Bootloader. I tried the 1GB and 256MB (1GB This had not had a problem with my PDA). An attempt to flash the original RUU ROM also failed
(ERROR [244] Invalid device ID) and at the bottom right corner of the strange combination of characters.
My data from the bootloader:
IPL 4.17.0001
SPL 4.70.Yang
Can you help me?
Please, quick help.
[ORIGINAL PL]
Witam
Po ostatniej zmianie ROMu miałem problem z włączeniem PDA więc wykonałem HR alle...
...po HR przy bootowaniu zamiast logo ekran stał się zielony. Postanowiłem że wgram
softa przez kartę pamięci ale nie wykrywa pliku HERAIMG.nbh tylko od razu leci do
bootloadera. Próbowałem na 1GB i 256MB (Ta 1GB wcześniej nie miała problemu z moim PDA). Próba flashowania przez RUU oryginalnego ROMU też się nie powiodła
(ERROR [244] Invalid device ID) a na dole w prawym rogu dziwna kombinacja znaków.
Moje dane z bootloadera:
IPL 4.17.0001
SPL 4.70.Yang
Możecie mi pomóc?
Proszę o szybką pomoc.

refresh
refresh

Cavion 7.1 base 4 root and bootloader problem.

Hello.
I have a problem. I have a tablet Cavion 7.1 Base 4.
I wanted to do root to be able to use the application Link2SD. (I've done it once already in my motorola Deffy mini xt320 there and it worked).
Tablet wanted to do the same thing, but it was not easy. The only solution I found was to install applications KingRoot which is poor. Part of the application requires SuperSU and that I could not use because I had no root. KingRoot did root but I could not install SuperSU the system continues to operate KingRoot.
For several days the tablet started to happen strange things stopped working screen rotation accelerometer, applications active on the top started off even though the earlier work properly. 2 days ago ceased to open the keyboard. in different applications. I wanted to do a factory reset. When you reset the tablet crashed and all night imaging the "erasing". Today I managed by ADB reboot device. The data have been removed but partially. still does not work rotation etc .. I did ADB reboot bootloader and the device hangs on the manufacturer's logo. The system detects the device as "Android ADB Interface" (USB \ VID_1F3A & PID_1010) but the same ADB can not see it.
Actions such long pressing power button or other combinations vol + does not work (sometimes earlier succeeded in Vol + and Power turn recovery which also crashed during the reset date but you could get out of it)
Does anyone have a solution to the problem of the tablet to start and how to solve the problem of root for this device?
If you have links with bin files too please. Kernel Android etc .... and programs to flash and manual
translated by Google
Witam.
Mam problem. Posiadam tablet Cavion 7.1 Base 4.
Chcialem zrobić roota żeby móc korzystać z aplikacji link2sd. (robiłem już to kiedyś w mojej motorola deffy mini xt320 i tam się udało).
Na tablecie chciałem zrobić to samo jednak nie było to proste. Jedynym rozwiązaniem jakie znalazłem było zainstalowanie aplikacji KingRoot która jest słaba. Część aplikacji wymaga SuperSU a tej nie mogłem używać bo nie miałem roota. KingRoot zrobil roota ale nie mogłem zainstalować SuperSU do systemu, nadal działał KingRoot.
Od kilku dni w tablecie zaczęły dziać się dziwne rzeczy, przestało działać obracanie ekranu z akcelerometru, aplikacje aktywne na wierzchu zaczęły się wyłączać mimo że wcześniej działały prawidłowo. 2 dni temu przestała otwierać się klawiatura. w różnych aplikacjach. Chciałem zrobić reset fabryczny. Podczas resetu tablet zawiesił się i całą noc wyświetlało się "erasing". Dziś udało mi się za pomocą ADB zrebootowac urzadzenie. Dane zostaly usuniete ale czesciowo. nadal nie działa obracanie etc.. Zrobiłem ADB reboot bootloader i urządzenie wisi na logo producenta. W systemie wykrywa urządzenie jako "Android ADB Interfejs" (USB\VID_1F3A&PID_1010) ale samo ADB go nie widzi.
Operacje typu wciśniecie długo przycisku power lub inne kombinacje vol+ nie nie działają (wcześniej czasem udawało się Vol+ i Power włączało recovery które też zawieszało się podczas reset data ale dało się z tego wyjść)
Ma ktoś rozwiązanie problemu żeby tablet się uruchomił i jak rozwiązać problem z root dla tego urządzenia?
Jeśli posiadacie linki z plikami bin tez prosze. Kernel Android etc.... oraz programy do flashowania i instrukcja
przetłumaczone przez google

I have the same my friend

I cant boot my phone

Hello, I have rooted my device using this tutorial https://forum.xda-developers.com/one-a9s/how-to/root-htc-a9s-magisk-t3680322 and after some time i decided to unroot and i didnt know how to unroot so i read in internet and i uninstalled magisk manager using the option uninstall completely and it said that it will reboot in 5 second. After this i cant boot my phone, when i power it up it vibrates and shows htc logo the <orange state> above it and red text below the htc logo and after like 5-10 second it boots up again and again. I don't know what to do, please help me. Sorry for my english, i'm polish.

I think it's easy just flash stock rom or flash boot. Stock rom and all info you can find here https://forum.xda-developers.com/one-a9s/how-to/stock-signed-ruu-2pwdimge36mlul-1-01-t3535461

dobrydiler said:
I think it's easy just flash stock rom or flash boot. Stock rom and all info you can find here https://forum.xda-developers.com/one-a9s/how-to/stock-signed-ruu-2pwdimge36mlul-1-01-t3535461
Click to expand...
Click to collapse
Ty jestes z Polski co nie? Mogłbyś mi dokładnie napisac jak to zrobic bo ja jestem zielony w tych sprawach.

Hahah ściągnij ten plik https://drive.google.com/open?id=0B_BPVbgprz1uYkNVU3lSR1RVREU zapisz go na karcie sd i nazwij 2PWDIMG.zip wyłacz telefon i uruchomiając przytrzymaj power i głośność w dół i potem chyba musisz nacisnąć jakiś przycisk ale nie pamiętam który żeby zacząć instalacje