Related
Hi,
I decided to flash Virtuous ICS ROM + accompanying firmware 1.24 flashed from hboot + 1.7 new kernel (previously used Revolution Gingerbread ROM stripped of all Sense).
Everything is smooth but I noticed phone data coverage shows Edge everywhere it used to show HSPA+ on all the highways.
I assume radio is not including TMobile bands, should I find a different firmware? I assume the issue is a firmware and not kernel or ROM, but I used link for firmware that is mentioned in the main Virsuous ROM thread that is supposed to be compatible with the ROM. Perhaps it is not compatible with TMobile though?
Thanks,
Vadim.
Check if Auto GSM/WCMDA is enabled in the mobile settings.
Which ROM? Did you flash h boot 1.27 after flashing ROM or before?, It has a new radio and ril., if you flashed your ROM after the firmware update the RIL May not match.
Sent from my HTC Sensation 4G with Beats Audio using xda premium
Like ARHD it's probably based on the EU ROMs so there isn't a 4G icon.
Flash a 4G icon mod.
xdviper said:
Check if Auto GSM/WCMDA is enabled in the mobile settings.
Click to expand...
Click to collapse
Ahh, slaps himself in the face
Indeed, GSM was in Mobile settings. Tried ten times to change to GSM/WCDMA and the setting always returned back to GSM and phone still showed Edge.
Today on eleventh attempt for some reason setting finally got saved and phone shows H (for HSPA+). Thanks!
Mainly for Canadians.
If you want to use it on I727R with ICS Rom. please ONLY flash the base file (no RIL).
http://dl.dropbox.com/u/4333782/Bell_Note_Base.zip
If you want to try it on different gingerbread flavors, you can flash the one with RIL. DO NOT flash this one on ICS, otherwise you will not get signal.
http://dl.dropbox.com/u/4333782/Bell_Note_Base_RIL.zip
After you flash the radio file, ICS may not identify the baseband properly(from About Phone). On GB TPC v3 can detect the baseband properly though.
LeeC said:
Mainly for Canadians.
If you want to use it on I727R with ICS Rom. please ONLY flash the base file (no RIL).
http://dl.dropbox.com/u/4333782/Bell_Note_Base.zip
If you want to try it on different gingerbread flavors, you can flash the one with RIL. DO NOT flash this one on ICS, otherwise you will not get signal.
http://dl.dropbox.com/u/4333782/Bell_Note_Base_RIL.zip
After you flash the radio file, ICS may not identify the baseband properly(from About Phone). On GB TPC v3 can detect the baseband properly though.
Click to expand...
Click to collapse
I flashed the Rogers no RIL, works great, better bars, however how damaging it to have unknown baseband?
not damaging at all, the rom will merely identify baseband as "unknown," as u said.
Im curious to know how much better this modem performa compared to the UCALC4. I had problems flashing it before, but once i got it to stick performance has been great, receptions is better and speed on par with UCLA3. Can other rogers users with LTE weigh in on this? Preferably those in the GTA and Vancouver.
does the resolve the unknown caller issue
Hey gey just here to give my feedback about this modem. (I live in GTA)
Personally, I've experienced slower data speeds and bars of reception with this modem as compared to the UCALC4 modem.
On this modem (no ril) I acquired about 20 mbps down and 8 up where as with the UCALC4 modem, I experienced about 26 mbps and 13 up.
Also, with the no ril modem, I was receiving 3 bars while on the UCALC4, I was receiving 4 bars.
maybe because it is a bell modem and rogers will release their own?
I made this for some users can try to use Bell's dual channel HSPA+ as y2whisper advised. For LTE it may not as good as rogers or UCLA4.
LeeC said:
I made this for some users can try to use Bell's dual channel HSPA+ as y2whisper advised. For LTE it may not as good as rogers or UCLA4.
Click to expand...
Click to collapse
but to be honest im running 4g which is another 3g+ and i didn't see any difference but my battery was going upside down lol..as far as ucalc4 once it settles, its wayy better then then RUKJ7 that we have with rogers..
for me its helpful since i am using the device on bell. and well i don't have the same coverage with bell as you do with rogers for LTE. so figured why not get the best hspa+ speeds as i can get.
(never noticed you were from brampton before)
Has anyone tried flashong the UCLA3 modem on ICS ROMs?
Sent from my SGH-I727R using XDA
cue_32 said:
Has anyone tried flashong the UCLA3 modem on ICS ROMs?
Sent from my SGH-I727R using XDA
Click to expand...
Click to collapse
I tried UCLA3 on ICS yesterday because I can't get LTE on UCALC4. Anyway, it doesn't work. It gives no signal and under 'about phone' it says unknown baseband.
did u try the ics specific one leeC posted?
My mistake, I didn't flash the ICS specific UCLA3. Didn't know of it. Flashed the GB one (no signal) -then flashed back to UCALC4 radio. Ill try ICS UCLA3 soon (it would sure help if someone could post the link so I know for sure)
UCALC4 doesn't seem to be working too well for me. I get LTE very rarely for few seconds at a time only, but mostly not. I always had LTE before though.
I see this Bell Radio works on Rogers i727R. I have not tried it yet myself. I am on TCP v3 still, and looking to try a ICS rom with a new radio, but I am trying to find the Rogers radio in case I want to revert to gb ? Any thoughts ? this is the only radio post i see in the thread, thanks
This thread is actually in the wrong section, general or even dev section would have been better, but I digress.
Flash kj7 radio from this thread if u need rogers radio:
http://forum.xda-developers.com/showthread.php?t=1384865
icenight89 said:
This thread is actually in the wrong section, general or even dev section would have been better, but I digress.
Flash kj7 radio from this thread if u need rogers radio:
http://forum.xda-developers.com/showthread.php?t=1384865
Click to expand...
Click to collapse
Much appreciated ! Thank you !
i was using cleanrom 3.1 for a while, and everything was working fine. but i seen the new version (4.1) http://forum.xda-developers.com/showthread.php?t=1655011 and couldn't resist all the new features and mods lol.. thing is, now that i updated to 4.1 my LTE is no longer working, its just using 4G
ive tried the same settings i used before on cleanrom 3.1 and they don't seem to work. settings as seen here ===> http://dl.xda-developers.com/attach...166a897/4ffa16a7/1/1/2/3/8/6/9/Rogers_APN.txt
i flashed back to my old nandroid backup which was a stock rom and the LTE was working fine again. but when i flash to cleanrom 4.1 the LTE doesn't work, even after putting the APN settings in..
any help would be much appreciated, i need my LTE to work or there is no point lol, not worth having a custom rom if i don't get LTE speeds that i pay for
edit: nevermind.. it just started working musta been something on the rogers end of things. woot!
I have a 727r and I want to use it on wind, and have no idea what combo of rom / kernal / modem to use. what I do know:
The 727r radio has the ability to pick up the signal
The wind network uses HSPA+ - transmit on 1700, receive on 2100
There are modem files out there for these frequencies
Things I don't know
How to make sure a rom / kernel / radio will work with each other (hopefully without needing to spend hours flashing n! combinations)
How to figure out if a modem file will support my device, or the frequencies I need
Things I've tried
the 989 from Tmobile runs on HSPA+, so I tried installing a tmobo rom, kernel, and radio with little success.
Trying to install / flash different rom - kernel - modem combos (most of which results in baseband version:unknown - this means the modem and rom are incompatible right?)
What I'm asking
Is there anyone running a 727r on wind that wouldn't mind sharing their rom / kernel / modem combo?
Has anyone found a Cyanogen-kernel-modem combo that works?
I am NOT asking which is the "best". After spending 4 hours of flashing and praying things will work, I don't care if I get the "worst" rom. I just want a combo that works
WORKING(more or less) COMBOS:
R34P3ReX_T989_Skyrocket_Conversion - Juggernaut_50_0218 - Tmo_SGH-T989_KID_radio
Gingerbread base, gyroscope tilts screen wrong way, a bit buggy, but works
CM10, CM10, T989UVLH1
Works well enough, having Call issues though. Going to try a new radio
Cyanogen always gets terrible battery. Going to look for an optimized version but not a problem for me
CM10, Blaze 4G UVLH5
Calling worked, I could hear caller, but they heard a lot of garbled blarky. Not good
u don't need a specific ROM or kernel at all, all u need to do is try different t radios. try the uvle1 from the t989 aka Hercules subsection, and give the modem someone dumped from the i757m bell version to see if u can catch a signal. I strongly believe the later will work
pileot said:
I have a 727r and I want to use it on wind, and have no idea what combo of rom / kernal / modem to use. what I do know:
The 727r radio has the ability to pick up the signal
The wind network uses HSPA+ - transmit on 1700, receive on 2100
There are modem files out there for these frequencies
Things I don't know
How to make sure a rom / kernel / radio will work with each other (hopefully without needing to spend hours flashing n! combinations)
How to figure out if a modem file will support my device, or the frequencies I need
Things I've tried
the 989 from Tmobile runs on HSPA+, so I tried installing a tmobo rom, kernel, and radio with little success.
Trying to install / flash different rom - kernel - modem combos (most of which results in baseband version:unknown - this means the modem and rom are incompatible right?)
What I'm asking
Is there anyone running a 727r on wind that wouldn't mind sharing their rom / kernel / modem combo?
Has anyone found a Cyanogen-kernel-modem combo that works?
I am NOT asking which is the "best". After spending 4 hours of flashing and praying things will work, I don't care if I get the "worst" rom. I just want a combo that works
Click to expand...
Click to collapse
So.. im using the Tmo Radio.. the latests and you can get it here: http://forum.xda-developers.com/showthread.php?t=1895400
and as for the ROM i am using Cyanogenmod 10.0 but the T989 version.
works good.. dont forget to wipe everything.. as for the other comment where you just need to flash the radio.. dunno.. i tried that a couple of times and it didnt work.. however.. im about to try it again.. so ill let you know how it goes.. for now though.. just to get it working.. i would do the above..
tip: i initially flashed the UVLH1 radio.. worked great.. great signal.. then i updated the other day to the latest.. and it seems as though my signal is not as strong.. dunno.. but try it out.. you never know..
also.. on initial boot up.. you need to give it a couple of minutes for things to settle.. it should pick up the Wind signal by itself... if it doesnt after 5 mins.. then do a search.. but you shouldnt have a problem..
So.. i can confirm that you CAN install the TMO radio and the ATT Skyrocket CM 10 ROM!!!!!
Infact... it works great!!!
TIP: i can also confirm that the UVLH1 has a stronger signal than the UVLI4 radio which is the latest. not sure why.. but i reverted back to UVLH1
hope this helps!
df186 said:
So.. i can confirm that you CAN install the TMO radio and the ATT Skyrocket CM 10 ROM!!!!!
Infact... it works great!!!
TIP: i can also confirm that the UVLH1 has a stronger signal than the UVLI4 radio which is the latest. not sure why.. but i reverted back to UVLH1
hope this helps!
Click to expand...
Click to collapse
I have ROGERS_ICS_ULFX3 stock rom installed, baseband T989UVLH1, I flashed it and i get no sim error
Just before this on Stock gingerbread i had gotten it to work, but after 1 restart, everything got screwed up
Help me
I have been running SkyJB 4.1.2, and Blaze LB7 in Southern Ontario, picking up Wind signals. Speeds are okay, still trying to find the best combo, but that combo works.
kr4tos said:
I have ROGERS_ICS_ULFX3 stock rom installed, baseband T989UVLH1, I flashed it and i get no sim error
Just before this on Stock gingerbread i had gotten it to work, but after 1 restart, everything got screwed up
Help me
Click to expand...
Click to collapse
flash the radio twice,no cable plugged in before flashing rom, might help
df186 said:
So.. im using the Tmo Radio.. the latests and you can get it here: http://forum.xda-developers.com/showthread.php?t=1895400
and as for the ROM i am using Cyanogenmod 10.0 but the T989 version.
works good.. dont forget to wipe everything.. as for the other comment where you just need to flash the radio.. dunno.. i tried that a couple of times and it didnt work.. however.. im about to try it again.. so ill let you know how it goes.. for now though.. just to get it working.. i would do the above..
tip: i initially flashed the UVLH1 radio.. worked great.. great signal.. then i updated the other day to the latest.. and it seems as though my signal is not as strong.. dunno.. but try it out.. you never know..
also.. on initial boot up.. you need to give it a couple of minutes for things to settle.. it should pick up the Wind signal by itself... if it doesnt after 5 mins.. then do a search.. but you shouldnt have a problem..
Click to expand...
Click to collapse
I tried to install the T989 (Hercules) CM10 version but it kept failing to install
The recovery I'm using is Team Win Recovery, if that matters. I suspect either TWRP is not working or the Kernel is incompatible
What Kernel are you using?
pileot said:
I tried to install the T989 (Hercules) CM10 version but it kept failing to install
The recovery I'm using is Team Win Recovery, if that matters. I suspect either TWRP is not working or the Kernel is incompatible
What Kernel are you using?
Click to expand...
Click to collapse
if it was built for t989 specific phones it wont install because of the assert
u dont need a t989 rom anyways, but if you want to try them out make sure the updater script doesnt have the assert function and do the rotation fix
I'm using the i727r (Rogers) running CM 10.1. I'm still on Rogers using the stock radio for now. Is there any consensus as to which radio file to flash for best results?
I know this thread is a little stale, but I figured I would throw in my two cents.
I have an i727r, unlocked. Right now I am running PACman Rom (http://forum.xda-developers.com/showthread.php?t=2178402) with the Blaze LB7 radio (4th from the bottom here: http://forum.xda-developers.com/showthread.php?t=1895400). They said I shouldn't be able to run an ICS radio with a JB Rom, but somehow it seems to be working. Note that the radio was on there before flashing PACman.
The kernel showing up in my phone info is the one that came with the PACman Rom, 3.0.72-cyanogenmod. I know this because before flashing PACman over stock, the kernel was 3.0.8.
Having said all that I'm thinking about updating my radio, probably to UVMB1. I'm not sure if I should bother though. I have a Nexus S, which is designed as an AWS phone out of the factory, and when I put my SIM card in that phone, the speedtest results are the same as what I'm getting right now with the LB7 radio on the Skyrocket. So I'm not sure I'd gain much by updating. :/
Can some people in the GTA please chime in to help me.
I am using a Rogers Skyrocket.
SlimBean Rom 4.2.2 Official 7
T989UVMC6 radio/modem
I tried a few other modems and found this one to be the most stable as some did not even allow a call to be made.
This is what I noticed.
Full charge I talked for 20 minutes and lost 10% battery (from full charge)
I get erratic data speeds inside=500-1 and outside I get 3
The problem is the battery drain and signal strength.
What are you using and what is your battery life and signal strength?
Data speeds?
your location?
droiduzr2 said:
Can some people in the GTA please chime in to help me.
I am using a Rogers Skyrocket.
SlimBean Rom 4.2.2 Official 7
T989UVMC6 radio/modem
I tried a few other modems and found this one to be the most stable as some did not even allow a call to be made.
This is what I noticed.
Full charge I talked for 20 minutes and lost 10% battery (from full charge)
I get erratic data speeds inside=500-1 and outside I get 3
The problem is the battery drain and signal strength.
What are you using and what is your battery life and signal strength?
Data speeds?
your location?
Click to expand...
Click to collapse
My carrier is videotron, one of the most difficult carriers to get unlocked phones to work on. Here's what works for me, sim unlocked, rooted. Running cyanogenmod 10.1.0 RC2 with Blaze 4G LF4 radio, nobars battery saver and network booster. I'm still have the same issue as everyone else, baseband unknown and network type unknown. I've been running the stock kernel and I've been running like this for the past couple days, and touch wood, I haven't had any issues. I've tried the 2 Tmo radios, I got no signal what-so-ever, the telus radio kept dropping my connection, meaning, I would have to try and resend text messages several times before it would actually send. Now that I'm using my current setup, as described at the beginning of my post, no problems to date.
I hope my input helps out.
wraith79 said:
My carrier is videotron, one of the most difficult carriers to get unlocked phones to work on. Here's what works for me, sim unlocked, rooted. Running cyanogenmod 10.1.0 RC2 with Blaze 4G LF4 radio, nobars battery saver and network booster. I'm still have the same issue as everyone else, baseband unknown and network type unknown. I've been running the stock kernel and I've been running like this for the past couple days, and touch wood, I haven't had any issues. I've tried the 2 Tmo radios, I got no signal what-so-ever, the telus radio kept dropping my connection, meaning, I would have to try and resend text messages several times before it would actually send. Now that I'm using my current setup, as described at the beginning of my post, no problems to date.
I hope my input helps out.
Click to expand...
Click to collapse
Ur input doesn't really help... 10.1 REQUIRES ucmc1 or ruxau7 , neither of which ur using. Try one of those radios and then post results
Edited: UVMB1 as well
icenight89 said:
Ur input doesn't really help... 10.1 REQUIRES ucmc1 or ruxau7 , neither of which ur using. Try one of those radios and then post results
Click to expand...
Click to collapse
Well, if it NEEDS ucmc1 or ruxau7, why have I been running this setup for the past month with no issues!?
wraith79 said:
Well, if it NEEDS ucmc1 or ruxau7, why have I been running this setup for the past month with no issues!?
Click to expand...
Click to collapse
You will, or already have had issues you're not aware of.
Sent from my SAMSUNG-SGH-I727 using Tapatalk 4
wraith79 said:
Well, if it NEEDS ucmc1 or ruxau7, why have I been running this setup for the past month with no issues!?
Click to expand...
Click to collapse
Edited, UVMB1, the NEW Blaze 4G radio from this thread seems to work as well:
http://forum.xda-developers.com/showthread.php?t=1895400
But like x said, u had issues u just weren't aware of them. Problems don't just APPEAR for no reason.
this threads getting confusing.
ucmc1 and uxuma7 is for rogers and att users on cm10.1
if using unlocked skyrocket for other carriers then you would need compatible jb radio for the new/unlocked carrier for cm10.1 based roms
so for tmo/wind etc you would need UVMB1 for the AWS bands, there are other jb radios for telus, bell but don't know if/how well they work on said carrier.
so if your carrier uses the same frequency's as tmo then UVMB1 seems to be what users are reporting success with.
if your carrier is using same frequency as att/rogers then the ucmc1 or uxuma7 radio is what you need
correct me if im wrong
^^^ this is exactly what I said except in a more detailed explanation .
icenight89 said:
^^^ this is exactly what I said except in a more detailed explanation .
Click to expand...
Click to collapse
good, i just needed a confirmation so i can add that info and a link to this post in the radio section of the 1stop sticky
hello xda developers,
well i was about to flash Cyanogenmod 10.1.2 on my Verizon Samsung Galaxy SIII model SCH-i535 until i started reading user comments and many of them said that this rom is great except that many people are having issues with a very weak 4g signal. Now i started doing some research on this issue with the 4g signal on my verizon phone and it seems that many other are having this problem as well...
Now i am reaching out to those of you who have a CM rom on a verizon Samsung Galaxy S3, how is your 4g signal? Do you suffer from a weak signal like other people i have been reading about?
The reason I ask is because I need a strong 4g signal for work, but I REALLy want to flash CM 10.1.2 on my phone. I have flashed CM on other phones i have had in the past and I am currently using CM 10+ on my tablet -> Samsung Galaxy tab 2 10.1 model GT-P5113 and I really enjoy on my tablet. The thing is my tablet is a wifi only tablet so I can't judge it with a 4g signal.
Does anyone know if these 4g signals will be fixed on the last and final release of CM 10? Do you guys/gals think i should go ahead and flash CM 10.1.2 or do you think I should wait for the last/final release of the CM Rom.
Also I have another question...
I know that the Samsung Galaxy S4 is using Android 4.2.2. Is there an official Samsung Rom using Android 4.2.2 that i could possibly flash onto my Verizon Samsung Galaxy S3 model SCH-i535?
If there is an official rom could someone please provide me download link, and if all possible is there a tutorial available on how flash this official android 4.2.2 rom (if available).
I have been looking on the internet but i have not been able to find much...
Well i thank you all for your time and your assistance.
Thanks again,
-droidshadow
droidshadow said:
hello xda developers,
well i was about to flash Cyanogenmod 10.1.2 on my Verizon Samsung Galaxy SIII model SCH-i535 until i started reading user comments and many of them said that this rom is great except that many people are having issues with a very weak 4g signal. Now i started doing some research on this issue with the 4g signal on my verizon phone and it seems that many other are having this problem as well...
Now i am reaching out to those of you who have a CM rom on a verizon Samsung Galaxy S3, how is your 4g signal? Do you suffer from a weak signal like other people i have been reading about?
The reason I ask is because I need a strong 4g signal for work, but I REALLy want to flash CM 10.1.2 on my phone. I have flashed CM on other phones i have had in the past and I am currently using CM 10+ on my tablet -> Samsung Galaxy tab 2 10.1 model GT-P5113 and I really enjoy on my tablet. The thing is my tablet is a wifi only tablet so I can't judge it with a 4g signal.
Does anyone know if these 4g signals will be fixed on the last and final release of CM 10? Do you guys/gals think i should go ahead and flash CM 10.1.2 or do you think I should wait for the last/final release of the CM Rom.
Also I have another question...
I know that the Samsung Galaxy S4 is using Android 4.2.2. Is there an official Samsung Rom using Android 4.2.2 that i could possibly flash onto my Verizon Samsung Galaxy S3 model SCH-i535?
If there is an official rom could someone please provide me download link, and if all possible is there a tutorial available on how flash this official android 4.2.2 rom (if available).
I have been looking on the internet but i have not been able to find much...
Well i thank you all for your time and your assistance.
Thanks again,
-droidshadow
Click to expand...
Click to collapse
I would flash cm10.1 and try it out for yourself. I ran it a couple days ago and the signal bars are lower but I hear that that's how they were made by Google to be more accurate. Idk. I an running carbon and my signal is 2/4 bars compared to touchwiz which I get 4/5 bars. Buy my connection is still fast which I used speed test to see if there was a different signal strength, which was not true.
And No official/leaked 4.2.2 TW released for our phone yet
Sent from my SCH-I535 using Tapatalk 2
krazie1 said:
I would flash cm10.1 and try it out for yourself. I ran it a couple days ago and the signal bars are lower but I hear that that's how they were made by Google to be more accurate. Idk. I an running carbon and my signal is 2/4 bars compared to touchwiz which I get 4/5 bars. Buy my connection is still fast which I used speed test to see if there was a different signal strength, which was not true.
And No official/leaked 4.2.2 TW released for our phone yet
Sent from my SCH-I535 using Tapatalk 2
Click to expand...
Click to collapse
So you are saying that with CM that your signal bars were low but your internet service was still fast?...
Would you say that with CM your internet connection was stable and that you consistently stayed in 4g and didn't go down to 3g too much?...
Also i know that you can do a full phone backup with titanium backup pro (which i have purchased) but if was to backup my phone and flash CM 10.1.2 how hard is it to flash back to the stock rom with titanium backup?
Also if i flash back to a stock rom would i loose my root status on my phone and have too root again or would everything go back to how it was?
I've never had to flash back to a stock rom before...so i am really curious how to that works exactly.
Thanks again so much for your response.
-DroidShadow
Questions and help issues go in Q&A and Help section
Thread moved
Thanks
FNM
droidshadow said:
So you are saying that with CM that your signal bars were low but your internet service was still fast?...
Would you say that with CM your internet connection was stable and that you consistently stayed in 4g and didn't go down to 3g too much?...
Also i know that you can do a full phone backup with titanium backup pro (which i have purchased) but if was to backup my phone and flash CM 10.1.2 how hard is it to flash back to the stock rom with titanium backup?
Also if i flash back to a stock rom would i loose my root status on my phone and have too root again or would everything go back to how it was?
I've never had to flash back to a stock rom before...so i am really curious how to that works exactly.
Thanks again so much for your response.
-DroidShadow
Click to expand...
Click to collapse
Make a backup in recovery (TWRP or CWM). Just use Titanium to backup/restore apps, and try to avoid restoring app data. Make sure all your backups are on an sd card or computer and not the phone, as you should wipe the data section when switching.
Returning to what you have now, if you don't stick with CM is as easy as wiping system and data and restoring the backup in recovery.
Try it out for yourself. CM reads lower bars because of a change google made. DBm wise the signals are exactly the same from CM to touchwiz. I have absolutely no problems with 4G anywhere it's available. And it hands off to 3G when the 4G signal is too weak, just like touchwiz.
I just went back from aokp to tw, now my gps is dead. Not sure what to do
Sent from my SCH-I535 using xda premium
ucpro said:
I just went back from aokp to tw, now my gps is dead. Not sure what to do
Sent from my SCH-I535 using xda premium
Click to expand...
Click to collapse
ucpro i read somewhere on touchwiz that if you are having issues with gps that you have to do a complete wipe and reinstall. Make sure to wipe everything.
Good luck man,
droidshadow
So I finally went ahead tried CM 10.1.2 the newest nightly build and I must say that I absolutely love it!! I am not having any issues with my 4g signal the camera is working great. I have heard that some people have been having issues with bluetooth and gps though. For gps that seems to work just great but I have not tried out connecting my phone via bluetooth.
I will try that in a bit and let everyone (who is interested/cares) how bluetooth works.
If you have a verizon sgs3 go ahead and give Cyanogenmod a try. Be sure to grab the latest nightly builds.
Also be sure to back up your apps with titanium backup and backup your stock rom with a recovery manager such as clockworkmod.
I would like to thank the CM developers and the people of this amazing forum. You guys are what make the open source community great!
Sent from my SCH-I535 using xda app-developers app