I am running Viper XL 4.2.2 and I updated the firmware to version 2.15 as recommended in the Viper thread. After updating the firmware my mobile data stopped working. It is saying "Connection failed due to incorrect APN setting". The odd part is that these are the same APN settings I was using before updating the firmware and they were working just fine then. I am using an unlocked AT&T HTC ONE X on metropcs. The APN settings I have been using are the ones found at http://forum.xda-developers.com/showthread.php?t=2491999
I have tried reflashing the ROM as well as redoing the update. Neither one has worked. I have had the issue running both the stock kernel and Beastmode Reloaded 3.5.
If anyone has any suggestions I would really appreciate it, I need my mobile data working as I am not always near a wifi signal I can use.
Related
Hi,
I recently decided to flash a jeallybean ROM since most of them are getting really great and we don't have any word on the official update. Unfortunatly, I'm now unable to get a data connection on my HOX. It's the rogers version which I unlocked and I'm now using on the Bell network. Before flashing, LTE worked fine with the stock sense ROM, but now I don't have any data at all.
ROMs I've tried :
AOKP, MIUI and CM10.
I've tried to : set the data connection to GSM only, nothing, to LTE only, nothing, to WCDMA only, nothing. I've tried all the APNs I've found (pda.bell.ca, pda2.bell.ca, inet.bell.ca). On AOKP it sometimes said "Error while searching for network". WiFi, texts and calls work fine.
If anyone could help me, it would be really appreaciated. Otherwise I'll just revert to Rogers ROM. Thanks alot!
I cant offer any help, but I'm having a similar issue recently. I was on a nightly build of CM10 (from 10/06/12 I believe). I upgraded to a newer build (from 10/10) and I get no data over cell. I flashed it back and things were fine.
Dravyy said:
Hi,
I recently decided to flash a jeallybean ROM since most of them are getting really great and we don't have any word on the official update. Unfortunatly, I'm now unable to get a data connection on my HOX. It's the rogers version which I unlocked and I'm now using on the Bell network. Before flashing, LTE worked fine with the stock sense ROM, but now I don't have any data at all.
ROMs I've tried :
AOKP, MIUI and CM10.
I've tried to : set the data connection to GSM only, nothing, to LTE only, nothing, to WCDMA only, nothing. I've tried all the APNs I've found (pda.bell.ca, pda2.bell.ca, inet.bell.ca). On AOKP it sometimes said "Error while searching for network". WiFi, texts and calls work fine.
If anyone could help me, it would be really appreaciated. Otherwise I'll just revert to Rogers ROM. Thanks alot!
Click to expand...
Click to collapse
Before flashing jelly bean roms you need to flash a sense rom then do full wipe and install cm10 or aokp..
jspidey said:
I cant offer any help, but I'm having a similar issue recently. I was on a nightly build of CM10 (from 10/06/12 I believe). I upgraded to a newer build (from 10/10) and I get no data over cell. I flashed it back and things were fine.
Click to expand...
Click to collapse
Sent from my HTC One X using xda premium
I have the exact same problem with my SGS using the X-bean 3.0 rom.
What's the best solution? Is it because I used to Cwm?
Svenomous said:
I have the exact same problem with my SGS using the X-bean 3.0 rom.
What's the best solution? Is it because I used to Cwm?
Click to expand...
Click to collapse
Every device has its own nuances, as do various ROMs. So I'd advise posting this in the forum specific to your device.
Still no data connection.
I am having the same issue with my AT&T One X phone.
The phone was running 2.20 before it was unlocked/rooted. Installed TWRP, was a noob and forgot to save a backup, fastbooted the boot.img, flashed AOKP and CM10 successfully. With both of these ROMs, I could not get internet to work via cellular connection. I have tried everything with the APNs (even had AT&T help me setup APN settings) and still no mobile data connection. I can still receive/send SMS/calls, use bluetooth and wifi, just no mobile internet.
I'm not entirely sure what to do next. I attempted to go back and flash the UrDroid 4.1 Stock Sense ROM, but after fastbooting it's boot.img and attempting to flash with TWRP, I got a signature verification failure. Got scared and restored back to AOKP (I remember to make a backup this time.)
Thoughts? Sorry for being a noob.
Are you in an LTE area?
redpoint73 said:
Are you in an LTE area?
Click to expand...
Click to collapse
I am in a "4G" area (HSPA+) but I am also a hour drive away from LTE. I have tried APNs for both, but AT&T recommended I stick to the LTE APN. AT&T had me go to Settings->More->Mobile Networks->Network Operators and the phone just sat there searching without finding anything. I just did that above operation again and it found AT&T and I selected it. It spins on "Registering on AT&T..." for a few minutes and eventually errors out "Cannot register on this network at this time."
Have you tried switching off LTE by selecting "GSM/WCDMA Auto" in Settings?
I've had data problems on certain ROMs, where turning off LTE got the HSPA+ connection working.
In that case, it was probably a base of build.prop not playing well with AT&T's network. Although I would think the ROMs you mentioned would have these issues worked out at this point (and for some time now).
redpoint73 said:
Have you tried switching off LTE by selecting "GSM/WCDMA Auto" in Settings?
Click to expand...
Click to collapse
When I switch to "GSM/WCDMA Auto", it immediately switches itself back to the LTE setting. This is concerning.
I have been using an ICS ROM (PrimoS v4.1) on my Desire S for some time with no problems, but recently have tried flashing a number of JB ROMs (e.g Andromadus, CM10 and JellyTime). I have found that when using any of these JB ROM's, I am unable to get a data connection and the APN list is blank. Despite many attempts to add APNs manually or by use of APN backup apps, I have failed to add an APN to the list.
Do I need to update the radio to solve this problem? I never did this when going from original HTC Gingerbread to the ICS ROM.
Please excuse the ignorance on this subject. I've read somewhere that there is a danger of bricking the phone when flashing radios, hence my reluctance to try without good reason!
I live in the UK and use Virgin Mobile.
Current radio is: 20.281.30.085AU_3805.06.02.03_M
All help appreciated - I've had a tantalising glimpse of the wonders of Jelly Bean and I'm desperate to get my data connection working!
TIA
I can't say whether changing radios will fix your problem. I use Radio 20.4801.30.0822U_3822.10.08.04 on CM10 and have no problems.
Sent from my Desire S
BillGoss said:
I can't say whether changing radios will fix your problem. I use Radio 20.4801.30.0822U_3822.10.08.04 on CM10 and have no problems.
Sent from my Desire S
Click to expand...
Click to collapse
Thanks for the reply BillGoss.
I took the plunge and updated my Radio to 20.4801.30.0822U_3822.10.08.04 with no problems. My phone continues to work fine with the PrimoS (ICS) ROM, but when I flashed JellyTime, still no APN's and I was unable to create one, hence I can't connect to the 3G network. D'oh!
Correct me if I'm wrong but with ICS you don't have the probelm and with JB you have the problem
that you have no and can not set the APN values, Q, dit you have a clean ROM installed.
I had this problem once when I tested a ICS version with sence 4. Later when I installed a CM10 version
I had no APN so I did a factory reset an de problem was gone. To be sure I wiped al the data on my device
and restored a earlyer nandroid backup. Later I tested a lote of ROMS but so far I don't have the APN issue yet.
HypnoCondor said:
Correct me if I'm wrong but with ICS you don't have the probelm and with JB you have the problem
that you have no and can not set the APN values, Q, dit you have a clean ROM installed.
I had this problem once when I tested a ICS version with sence 4. Later when I installed a CM10 version
I had no APN so I did a factory reset an de problem was gone. To be sure I wiped al the data on my device
and restored a earlyer nandroid backup. Later I tested a lote of ROMS but so far I don't have the APN issue yet.
Click to expand...
Click to collapse
Yes HypnoCondor, I always do a full wipe before flashing the ROM. I've now done a ot of Googling and trawling XDA threads and have found that the issue seems to be confined to CyanogenMod-based ROMS, not specifically CM10 and covering a lot of different phones. I'm not techie enough to fully understand, but it seems that CM is not registering the SIM card properly and hence the APN list is always blank and can't be edited/saved manually.
What's particualrly confusing is that I recently flashed the CM10-based CyanogenMod 10 Beta Builds [4.1.2][ANDROMADUS 3.x][Frontcam] ROM (http://forum.xda-developers.com/showthread.php?t=1776256) and much to my surprise it worked! My APN list was populated and all was fine. Unfortunately , after rebooting the phone, the APN's were gone and I've been unable to get them back, despite trying every trick in the book gleaned from XDA users with similar problems.
This is very frustrating, because I really love this ROM
Looks like I'll end up going back to the PrimoS (non-CM, ICS) ROM so that I can get my data connection back when I'm away from WiFi. That's a real bummer, but I'm damned if I've been able to find a fix for this issue.
Just for future reference: being unable to set APN has nothing to do with radio and has everything to do with the ROM you're using. But you've already found that out yourself.
Jack_R1 said:
Just for future reference: being unable to set APN has nothing to do with radio and has everything to do with the ROM you're using. But you've already found that out yourself.
Click to expand...
Click to collapse
Thanks Jack_R1. My final plan is to try replacing the SIM card - should receive it in a couple of days.
Phosbrom said:
Thanks Jack_R1. My final plan is to try replacing the SIM card - should receive it in a couple of days.
Click to expand...
Click to collapse
Phosbrom I'm on Virgin and the JellyBean roms you mentioned work great on our service. I'm sure you'll enjoy using them when your new sim arrives :good:
I've been having problems with AOSP-based ROMs (always perform a factory/system and dalvik wipe). It's just not stable at all. symptoms usually starts with 3G/wifi connection going down (the icons turning gray) and all sorts of problems follows like blinking screen, pressing app drawer and it goes back to home screen and etc.
My phone was running JB OTA before and thus was on hboot 2.14. I have since use the s-off trick and have use the earliest ICS RUU I found for Telstra XL to get it to the hboot 1.09. I've tried installing AOSP-based rom using hboot 1.09 and hboot 2.14 (use OTA to update ICS to JB) and nothing seems to help.
The problems I'm experiencing is not present in ViperXL at all (on hboot 1.09 and 2.14) which lets me to believe it is AOSP related or phone just doesn't like AOSP. :/
I really wish to use AOSP so if you could suggest solutions/workaround, I'll appreciate it very much.
thanks!
FWIW I had similar problems with ViperXL. The "network tweaks" that are installed during the Aroma installer was my issue. I installed viper and everything was fine until I decided to switch to another ROM (CleanRom 5.1) to be exact. And then I switched to CM10. My signal was absolutely **** network icon would gray out and the button to turn on mobile network was stuck in the turning on phase at least %80 of the time (didn't happen in viper for some reason). Couldnt figure it out so I flashed Viper XL again and selected generic network tweak and everything's been fine since.
nvmdfth said:
FWIW I had similar problems with ViperXL. The "network tweaks" that are installed during the Aroma installer was my issue. I installed viper and everything was fine until I decided to switch to another ROM (CleanRom 5.1) to be exact. And then I switched to CM10. My signal was absolutely **** network icon would gray out and the button to turn on mobile network was stuck in the turning on phase at least %80 of the time (didn't happen in viper for some reason). Couldnt figure it out so I flashed Viper XL again and selected generic network tweak and everything's been fine since.
Click to expand...
Click to collapse
if you meant the telco-specific selection during install, I picked "stock" on my mine as the telco I'm with is not in the list.
this isn't really a solution but more of a test. try this rom i had the best network connection ever on this rom to this day, it is also a good rom and you might even use it as a daily driver.
★☆★[ROM][11/29] Xplod JB 4.1.2, Bravia, Xloud, SONY Xperia For the One X☆★☆
I have installed 4.2.2 version of LiquidSmooth. But after installing it my network is dropping out within a min of talking. It's so annoying as I missed the most importing function. Talking to others using my phone.
ravi.kalyan said:
I have installed 4.2.2 version of LiquidSmooth. But after installing it my network is dropping out within a min of talking. It's so annoying as I missed the most importing function. Talking to others using my phone.
Click to expand...
Click to collapse
What radio are you using? You should be using UCMC1.
Sent from my SAMSUNG-SGH-I727 using xda premium
I have a similar issue. I've been running the March 23rd version of AoKp with no problems. However, I recently tried to install the latest version and my phone will not connect to the Rogers network (connects briefly during start up, then drops, this trend repeats infinitely). Even when I do get some bars of connectivity, it never actually registers with the network, so I cannot send/receive calls, sms, etc. All other functions work fine. Also of note; after first reboot after installing ROMs, all the correct APN's are there and it seems to default to Rogers LTE which is good, however never actually connects. Then, after a subsequent reboot, all APN's are missing and I cannot manually add any (when I save them, they don't actually save).
I've tried installing the latest version of CM - same issue
Tried flashing different radios to no avail (running UCMC1 currently)
Luckily I'm always able to restore my backup to that March 23rd version AoKp which still works without issue. My next step is to revert back to stock ROM and either stick with that or try installing a fresh custom following that.
Any idea what the issue is???
I'm seeing the same issue as well on AT&T.
I tried reverting back to the regular Cyanogenmod Rom, but I'm seeing the issue where the radio keeps dropping and connecting back every few seconds.
I'm on baseband UCLI3. Is that the best version to use?
LamboJ said:
I'm seeing the same issue as well on AT&T.
I tried reverting back to the regular Cyanogenmod Rom, but I'm seeing the issue where the radio keeps dropping and connecting back every few seconds.
I'm on baseband UCLI3. Is that the best version to use?
Click to expand...
Click to collapse
You need to be on ucmc1 for cm 10.1
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
Rooted, s-off vzw m8. After a fresh install I have no network connectivity. I try to alter the default APN but as soon as I change the MCC/MNC numbers the APN disappears from the APN list. This includes any new APN I make as well. Any ideas?
I can use other ROMs just fine, but any time i try to use ViperRom i have no connectivity.
i've tried dirty flashing, clean wipe, and ota updates from older versions. nothing seems to get this working.
screenshots at
oi59.tinypic.com/24x0vlw.jpg
oi59.tinypic.com/2j3mc14.jpg
oi62.tinypic.com/8y8c4l.jpg
the solution was to use a different version of twrp. i was originally using 2.7.0.3 which i can't seem to find anywhere and is now making me wonder if that was even an official release of twrp.