hey guys,
I tried rooting and flashing a new rom on my friend's Nexus S and things kind of went south. The phone doesn't boot up completely. it shows the google logo but nothing more. i can get into bootloader and from there into the CMW recovery. The phone's from Fido and I believe it's an i9020a. Right now once i get into the bootloader it say's "carrier info: ATT". I'm too used to working with odin. I found the right version of the stock rom to flash but it says "error status 7. installation aborted". Can anyone help me fix the phone?
shaahinjjj said:
hey guys,
I tried rooting and flashing a new rom on my friend's Nexus S and things kind of went south. The phone doesn't boot up completely. it shows the google logo but nothing more. i can get into bootloader and from there into the CMW recovery. The phone's from Fido and I believe it's an i9020a. Right now once i get into the bootloader it say's "carrier info: ATT". I'm too used to working with odin. I found the right version of the stock rom to flash but it says "error status 7. installation aborted". Can anyone help me fix the phone?
Click to expand...
Click to collapse
What rom did you flash?
Wipe data/factory reset in CWM. Fixes most booting problems unless you flashed a wrong rom.
yes i'm pretty sure i did flash the wrong rom. I flashed a miui rom here's the link to the thread: http://forum.xda-developers.com/showthread.php?t=1869369
I just need to flash the right rom but i can't find which is the right one. I already tried what you said but no luck.
I'm trying to get the fastboot to work. before i flashed anything it was working and my drivers on my mac would recognize the phone and commands would work in the terminal. now it just doesn't recognize the phone.
Hey guys,
I've been using this website as reference for years but never had an issue I hadn't already seen asked.
I've been looking for weeks for a solution to this and haven't found anything.
I tried to flash cm10.1 over my stock 4.1.2 and corrupted the system.
It was booting directly to AP Fastboot and showing an error about not calling the ROM properly.
I tried reflashing using RSD Light 5.7 but every time it tried to flash the system it said the phone returned failed.
So I upgraded RSD to v6.1 and tried again. This time the phone says it flashed properly but it freezes during the droid boot logo.
I've tried using the utility and it gives me the same results.
I can get into factory recovery and I've performed several hard resets. But the phone still freezes whenever it tries to load the system.
I'm using a Motorola Factory Cable on a high speed USB port.
Any ideas why I'm stuck in a soft brick that I can't flash out of?
ShiningRaven said:
Hey guys,
I've been using this website as reference for years but never had an issue I hadn't already seen asked.
I've been looking for weeks for a solution to this and haven't found anything.
I tried to flash cm10.1 over my stock 4.1.2 and corrupted the system.
It was booting directly to AP Fastboot and showing an error about not calling the ROM properly.
I tried reflashing using RSD Light 5.7 but every time it tried to flash the system it said the phone returned failed.
So I upgraded RSD to v6.1 and tried again. This time the phone says it flashed properly but it freezes during the droid boot logo.
I've tried using the utility and it gives me the same results.
I can get into factory recovery and I've performed several hard resets. But the phone still freezes whenever it tries to load the system.
I'm using a Motorola Factory Cable on a high speed USB port.
Any ideas why I'm stuck in a soft brick that I can't flash out of?
Click to expand...
Click to collapse
Format system via any of the custom recoveries before flashing your new ROM - this will wipe out any leftover problems completely & should let you start 100% fresh with a new ROM.
tzlot said:
Format system via any of the custom recoveries before flashing your new ROM - this will wipe out any leftover problems completely & should let you start 100% fresh with a new ROM.
Click to expand...
Click to collapse
I lost my root when I originally got stuck in fastboot. And I can't boot up the phone until I can get it fixed.
ShiningRaven said:
I lost my root when I originally got stuck in fastboot. And I can't boot up the phone until I can get it fixed.
Click to expand...
Click to collapse
Can you get back into fastboot now? If so
Use fastboot to flash a custom recovery (CWM, TWRP or OUDHS)
use the recovery to factory reset, wipe cache/dalvic, AND format system (sometimes in the advanced menu)
then flash rom of your choice.
If you can't get fastboot working you'll need smarter help than I can give you... but the format system step clears out all kinds of gremlins.
I can get into fast boot but I don't have an unlocked boot loader to flash anything custom.
ShiningRaven said:
I can get into fast boot but I don't have an unlocked boot loader to flash anything custom.[/QUOTE
If you can get into fastboot then you should be able to unlock b/l with this toolkit I used it and it worked for me you can also flash rom with it its in the orginial development thread
http://forum.xda-developers.com/showthread.php?t=2154995
Click to expand...
Click to collapse
ShiningRaven said:
So I upgraded RSD to v6.1 and tried again. This time the phone says it flashed properly but it freezes during the droid boot logo.
I've tried using the utility and it gives me the same results.
I can get into factory recovery and I've performed several hard resets. But the phone still freezes whenever it tries to load the system.
I'm using a Motorola Factory Cable on a high speed USB port.
Any ideas why I'm stuck in a soft brick that I can't flash out of?
Click to expand...
Click to collapse
Had the same problem after a fastboot via the utility. Try powering your phone down completely and leaving it off for about 5-10 min. This can be tricky with the hardware buttons so if you have access to TWRP that will help as it has a power off option. You might also try flashing again via the utility. I believe that's what I had to do, but the power down method is what a friend suggested based of his experience with the same exact problem you documented.
FIXED!!!
OK first I want to thank everybody who responded. I got tied up with work and kind of forgot about this project for a few days.
Repeated uses of the Utility and RSD both left me stuck with the phone freezing every time it tried to load the system into memory.
I had checked out the toolbox before but I didn't think I could do much from a locked bootloader.
After your suggestion jmcdonald I tried it again. It says my device isn't available to be unlocked so I tried downgrading back to ICS.
The toolbox says that it failed but it must have fixed something because the phone booted back up to android 4.1.2 stock!
So far I have bricked a lot of phones and learned a lot about ADB in the process of fixing them but I've never had one I was so certain was bricked permanently. But now it seems to be working fine, I'm scared to try rebooting in now.
Definatly going to unlock the bootloader pronto.
Thanks again jmcdonald!
Okay so I've tried everything, Ive used the fastboot loader for flashing the recovery and bootloader but cannot get into recovery. What's weird is this all started after recovering my phone from the official LG updater, I didn't know the official ROM even had fastboot.
Anybody has this issue? Really need to fix it.. about a week without my phone isn't good..
Really getting desperate and so far no help this is a serious issue, usually when using the Recover phone in LG updater you expect it to put it back to the way you got it, not install some stupid fastboot stuck version. Also I recovered it 3 times from the LG tool all the same thing.
Flash ICS with LG Flash Tool to reinstall everything fresh. That's what I would do, anyway... Updater tool needs to be banished.
http://forum.xda-developers.com/showthread.php?p=39269819
WKPark bootloader is installed by Fastboot, so no idea what is going on there.
FINAL EDIT: FIXED!!! Sparsechunk files 1,2and 3 have to match the exact name with the firmware folder sparsechunk files.
I did not notice that my firmware sparsechunk files ended in .0 .1 .2 and not 1 2 3 like the tutorial had listed, so I was fastbooting the wrong sparsechunk command. That was the final fix that finally worked for me.
Original post:
SHORT VERSION:
My god this has been one crazy root journey.
I have done absolutely EVERYTHING I could pull up on google to fix my phone, and what seemed to be the final piece to the puzzle, still has not fixed anything.
My phone is bricked, and i would really appreciate help at this point.
The current problem:
When I turn on my phone, it vibrates, and displays the WARNING BOOT LOADER UNLOCKED screen, and stays there forever.
I can access my boot loader, and recovery, but I dont know what to do at this point.
I tried a quick flash stock recovery kit kat with moto tool AIO, and it didnt help.
Any ideas?
LONG VERSION (backround info may help to understand the current issue)
Now, if you want to know what began all of this, continue reading, otherwise the above is my current issue.
After successfully unlocking and rooting my phone
I downloaded SWITCHME, an app that lets you create multible users on the phone. the instructions say that you can use a sub account to test and mess around with anything because you can simply go back to the admin account that has everything untouched.
That was a lie.
1.I deleted .setup, along with a few other things THAT WHERE NOT FLAGGED AS IMPORTANT, assuming the phone would still work. and my phone went bonkers, displaying this infinite message: UNFORTUNATELY, SETUP HAS STOPPED. It was impossible to use the phone, and I could only access bootloader.
2.After endless googling, driver downloading, xda mod installing, I managed to set up my boot loader to do the guide restore stock firmware:http://forum.xda-developers.com/showthread.php?t=2542219
Sadly, I flashed the wrong model number package, I was flashing x35, when I later discovered that my phone is x45.
Flashing the x35 firmware bricked my phone further, to where it would "fail to boot up" and would only display bootloader over and over after attempting to turn the phone on.
3. Simple, I realized I flashed the wrong thing, so I downloaded the x45 firmware from the firmware teem on this website, flashed all of the commands, and bam, the phone starts up with the boot loader warning, and DOES NOT get stuck in the previous boot loader issue I had.
But now the phone wont get past that warning screen so... now im pissed.
Please, if anyone can help me I would greatly appreciate it, Im so close to getting my phone back...
EDIT 2: Looks like the phone wont stay shut down, I realized that if I dont open up boot loader, it will turn itself on and display the warning message.
EDIT:
The stuffs I have, ready to try anything:
CWM touch mod
Moto Tool AIO
Minimal ADB and Fast boot
RETUS x1045 factory firmware
All directories, folders, cmd commands are set up and working properly between all of the programs.
The phone appears to be responding to all cmd commands properly.
I also have the windows one touch super boot root method. (he superboot-windows.bat )
Im afraid to try anything major after freshly flashing the x45 firmware that seemed to bring me one step closer without the help of someone else.
I restored stock to my phone using this link yesturday http://www.ibtimes.co.uk/how-restore-motorola-moto-g-stock-firmware-1447290
it may work for you
I have almost the same problem as if the fastboot not install anything despite not display errors
great that you got it done.
maybe my few cents about my "bricking" story. (xt1032 moto g)
yesterday i wanted to change the rom from cm11 nightly to another custom rom like ehndroix/carbonrom...
first i thought that will be done in a few mins, after having already flashed a custom rom.
then the story began, getting adb work, but, 2weeks ago everything was setup and went fine. dunno why my laptop lost the "drivers".
thats the link which solved that problem: tinyurl . com / kgffjh4 [sorry cant post links outside of xda yet, spam protection]
so after a few hours of getting that fixed i, i began flashing.
suddently i got stuck in bootscreen (ehndroix logo for example)...
then i wanted to go back with my previous backup made internaly of clockworkmod. though i couldnt restore my backup because there was an error message while restoring /data of my backup
also when restoring to factory/wipe in cwm there was that error message about clouldnt "touch" /data, i dont remember the message exactly.
after thinking i bricked everything, i though lets wipe my internal sdcard, maybe that causes the /data error.
then i restarted the device and went for a shower... after 15min i came back and my device was "started".
now i dont know that exactly helped, maybe wiping all data on my phone, or just letting my device boot for a "long" time...
so, thats my yesterdays brick story.
do a factory reset if the bootloader has that option.. otherwise install or run/boot a custom revovery, then either
try the factory reset option there and reboot or..
wipe everything and install a rom
Ok try this, I'm was a victim too:
Relock and unlock bootloader
Download and flash latest Philz
From there format everything...EVERY PARTITION...switch F2FS
After switching wipe every partition again
Select and execute the other 3 wiping option ie., Clean to install new ROM and the other 2 (I can't remember now)
Do this all over again via TWRP too
Now, this is important, don't use the mfastboot for restoring stock...use the one provided by Google for its Android SDK
Flash the stock images
Flash the Moto Razr boot animation and not the one for Moto G to remove the warning sign
I'm 99.99% sure your phone will boot properly
After the phone boots, reflash the Moto G bootanimation
Good Luck!
ngr.hd said:
Ok try this, I'm was a victim too:
Relock and unlock bootloader
Download and flash latest Philz
From there format everything...EVERY PARTITION...switch F2FS
After switching wipe every partition again
Select and execute the other 3 wiping option ie., Clean to install new ROM and the other 2 (I can't remember now)
Do this all over again via TWRP too
Now, this is important, don't use the mfastboot for restoring stock...use the one provided by Google for its Android SDK
Flash the stock images
Flash the Moto Razr boot animation and not the one for Moto G to remove the warning sign
I'm 99.99% sure your phone will boot properly
After the phone boots, reflash the Moto G bootanimation
Good Luck!
Click to expand...
Click to collapse
I try to flash any recovery but after entering I get an android and says no commands, and installation does not throw errors
angelgzg said:
I try to flash any recovery but after entering I get an android and says no commands, and installation does not throw errors
Click to expand...
Click to collapse
You're still in stock recovery.
Use fastboot flash recovery xyz.zip to flash philz recovery
Use this when you're in bootloader mode.
ngr.hd said:
You're still in stock recovery.
Use fastboot flash recovery xyz.zip to flash philz recovery
Use this when you're in bootloader mode.
Click to expand...
Click to collapse
I flash the recovery but rebooted into recovery, the android keeps popping up (no commands)
FINAL EDIT: FIXED!!! Sparsechunk files 1,2and 3 have to match the exact name with the firmware folder sparsechunk files.
I did not notice that my firmware sparsechunk files ended in .0 .1 .2 and not 1 2 3 like the tutorial had listed, so I was fastbooting the wrong sparsechunk command. That was the final fix that finally worked for me.
Sorry I'm traveling a d couldnt update thread fast enough.
I am running philz 6.41. I updated to nj3 on my sph-l710. Every time it boots it shows a error that the system file is corrupted.
I did encrypted the system along with the SD card. it says to do a factory reset but does not help. I did the same with my wife phone but her phone is working fine. Pleas help how can I get my phone back. If i try to flash any roms I get please update binary in philz.. I have tried to flash the stock rom and use kies factory recovery.
Hi,
Here is a guide on flashing stock. If you have any questions you can ask there too...
http://forum.xda-developers.com/showthread.php?t=2774333
Also, Kies must not be running for Odin to work properly. Check in your PC's task manager and kill any kies processes that are running before starting Odin.
Good luck!