Related
I have been having this error where the phone prevents itself from booting, showing a screen that tells you to connect to PC , for a while. Only way to fix it is to remove the battery and restart but that is just a temporary fix. What exactly is this? What causes it? Is it a software issue or a hardware issue? Should I get an exchange or do you guys think this will be fixed with the next update?
Thanks
Never seen that error message. I'd say reset once, if you see it again, get it exchanged.
Yea this my 4th HD7 it shows the error code when you plug it to the PC in zune. Funny thing is that I owned a speck case and I reboot the phone in the case till then. This time i pulled the battery out, put it back in and powered the phone on without the case and it is working fine. I guess the case is pushing down a button or sth and that prevents the phone from working properly. Very weird..
Hey there! I've been having the same error! This is my 2nd HD7, I own the Speck case and I do not think its the case. This issue is happening on mine with or without the case. Pulling out the battery just doesn't cut it. I have to:
1. Remove the battery
2. Plug the USB Charger
3. Insert the battery back
4. Turn on.
I love the phone but this is really frustrating!
Edit: Too bad I can't post the link to youtube due to member status. But the video is up just search for it "c101002e"
Just happened to me too. First day using the Speck case too and i let the battery drain till it died and upon reboot it showed the 'plug into computer' screen. Hope it is just the case causing problems.
did you all updated the sd card ?
you could try to reflash this rom (if you are on t-mobile USA ) http://forum.xda-developers.com/showthread.php?t=810346
Take this one "RUU_Schubert_TMOUS_1.20.531.01_Radio_5.51.09.11a_2 2.31.50.09_Signed_SCHUBERT_RELEASE"
its just the stock tmous rom .
Weird coincidence that all of y'all are using the same case. Maybe it is damaging on of the buttons?
nrfitchett4 said:
Weird coincidence that all of y'all are using the same case. Maybe it is damaging on of the buttons?
Click to expand...
Click to collapse
somewhere on the board they did tell that this case make the buttons really sensitive and it make the phone unusable .
theres a thread on tmobiles forums talking about the same issue, and most if not all the people there have the speck case. Someone says they tested it with and without the case and came to conclusion that the case is putting too much pressure on the camera button, which seems to be causing the problem.
would post the link to the other forum but i cant find it lol
pierce_m said:
theres a thread on tmobiles forums talking about the same issue, and most if not all the people there have the speck case. Someone says they tested it with and without the case and came to conclusion that the case is putting too much pressure on the camera button, which seems to be causing the problem.
would post the link to the other forum but i cant find it lol
Click to expand...
Click to collapse
Yea that was pretty much what was happening to mine. Although I remember trying to boot it without the case and having the same error before so what I did that I did a hard reset ( press power and both volume buttons at the same time) then when the phone booted, I rebooted it without the case immediately and its been working no problem since. I am pretty sure that case pushes the camera button since it grips the phone very tightly. I even overloaded the ram by opening lots of apps that runs in the background and then rebooted but it is working perfectly fine as of right now. Weird.. I am guessing its just a weird bug not a hardware defect.
I found it in a post in the mozart forums, so i tried it, as you do, cause its something new to play with cause my TP2 didnt like swimming, but anyway it was something about hoding down the camera button while power on, and it brought up a picture of a phone and cable and instructing you to plug it into a pc and when i did it started Zune and something about restoration error, so like in the previous posts it may be a stuck or faulty button somewhere on the phone that is causing it.
i didnt watch the video so if that had it in it never mind
cheers
Today 11 April 2011 I got notification about NoDo update for my phone.
It is HTC Mozart on Orange France network.
The pre-NoDo update was istalled about 20 days before.
The update got stuck at step 8. It seemed I had an unusable phone. In a periodic reboot mode into the update screen.
I checked on my W7 64 bit laptop the relevant backup folder, where all my phone data was supposed to have gotten backed up during the update. The folder was empty.
I therefore realized my phone got its rom corrupted during the update and I could not get back my pre-NoDo backup, since this latter was missing from my laptop.
Zune was on no help, stating a C101002E error.
The Windows Phone Support Tool was also of no use, reporting an error code while trying to restore my data.
XDA-forum provided me with a solution:
I went here
http://forum.xda-developers.com/showthread.php?t=1000781
and downloaded both bootloaders with relative roms.
After getting into the bootloader screen (red, green and blue screen), I installed the first ROM provided by Ansar. This could not install succesfully.
With the bootloader tool I could nevertheless confirm my idea I did not have anymore a functioning rom into my phone.
The second rom, the one ending with "Signed_by_ansar" could be succesfully installed.
I now have a Mozart fully functioning.
I had to restore my windows live account, Gmail, etc. My apps did not come back up after syncing with Zune.
I realized I just lost all my SMSs and home screen settings.
My phone was originally network unlocked and remained as such.
I got a notification that there is an official update for my phone the first time I rebooted. I will wait before attempting this update. The ROM by Ansar has got anyway copy/paste, being a NoDo ROM.
The ROM from Ansar, although for Orange France, removes the Orange splash screen when the phone starts. I guess if I need to use warranty on this phone right now I may have some issues with Orange France. Maybe when I update the phone following the update notification I got, I will re-establish a fully certified Orange ROM.
i9o pls and any one pls help me , i faced problem with [260] connection problem between my hd7 and pc vista 64 bit, actually i followed to steps in forum (error code C101002E) and drivers were installed (htc usb sync) before i started to flash rom NoDo bootloader 1, But no way still the problem [260]. i also tried another RUU htc asia xxx707xxx. because i have spl 1.23.2250.0(112138).also some links of RUU to download signed by ansar disappeared in rapid and other sourses, pls help to solve connection problem
Microsoft has release the Windows Phone Support Tool to fix this problem: http://support.microsoft.com/kb/2530409
WPS doesnt help in my case, Im malaysian and thought that need Asia RUU, but when i tried Europian RUU it nicely works, maybe because of i have 8G phone. the RRU is RUU_Schubert_HTC_Europe_1.69.401.01_Radio_5.54.09.21_22.33b.50.10_Signed_SCHUBERT_RELEASE(2)
day2die said:
Microsoft has release the Windows Phone Support Tool to fix this problem: http://support.microsoft.com/kb/2530409
Click to expand...
Click to collapse
Do you know what this tool does to the computer?
I would try it but honestly don't want to do it before I have info what it does to my PC settings. Unfortunately MS doesn't share with this knowledge.
Hi everyone!
I have a big problem with my new hd7.
Just bought, and wired for the very first charging but the phone continues to restart by itself.
Tried a hard reset, to set it in download mode and fix with Windows Phone Support Tool but still nothing to do. Even tried to install a new ROM but at the first start it continues with its loop.
In download mode zune tried to upgrade to nodo but it shows the error C101002E.
Don't know what else to do. Any idea? It's new!
MusicMan587 said:
Hi everyone!
I have a big problem with my new hd7.
Just bought, and wired for the very first charging but the phone continues to restart by itself.
Tried a hard reset, to set it in download mode and fix with Windows Phone Support Tool but still nothing to do. Even tried to install a new ROM but at the first start it continues with its loop.
In download mode zune tried to upgrade to nodo but it shows the error C101002E.
Don't know what else to do. Any idea? It's new!
Click to expand...
Click to collapse
No one had this problem? am i the only unlucky on the earth!?
Return for warranty replacement. Your phone is broken.
Thank you...i hoped i could solve it to not to wait september to have my phone back.
Hi all. Its been a while since I've lurked around here. Long story short, I've had a lot of life changes over the past year.. and I've also had a few system crashes/rebuilds so I've lost a lot of my old RT dev work & environment. Anyway, I'm looking to back into it and spare a few cycles playing around with things again. I recently dusted off my Surface RT and noticed I haven't updated it since Feb 2013 (!!). Given that the old JB thread is now locked, can anyone confirm that the JB still works with the latest/recent updates? If not, can anyone confirm the last update for which the JB still works correctly? I did some quick searches, but couldn't find any concrete info.
Thanks in advance!
Cheers!
It does with the new updates. Just don't install KB2973544 and KB2885699. One is an auto 8.1 update. Jailbreak doesn't work on 8.1.
Welcome back! Good to have you. The RT hacking scene has gotten pretty sad lately.
The jailbreak does still work on 8.0 (although I got one instance where it slowed the tablet terribly for a couple minutes then bluescreened with a stop message about a critical process dying, but usually it works fine). The current primary focus is on getting it working with 8.1. Read the first few parts of the 8.1 jailbreak threads to see what the problems are (in short: CSRSS is now a protected process so we can't debug it, and PatchGuard now checks the signature enforcement flag so the tablet will bluescreen after a while if you modify it). If you want to help, get in touch with @Myriachan (if you aren't already; I think there was somebody else working on it but I forget who) and see whether you can lend a hand.
If we can get past the first problem (protected process), I have some ideas how to handle the second one (PatchGuard). I can't guarantee it'll work, though; bypassing that stuff is hard and I've never tried before.
If you want to have a test install of 8.1 alongside your 8.0 install, that's possible. However, it takes a lot of storage space; I'm not sure if it can be done on the 32GB model.
GoodDayToDie,
Thanks for the summary! Glad to hear that I should be able to updated my 8.0 install and still JB.
I spent a few hours catching up on the 8.1 JB status/thread -- lots of good info in there. I might try my hand at dual booting (64GB Surface RT here) and poke around 8.1 -- I have a few ideas and I'd like to have a look at some of the binaries/changes.
I've also gotta setup my dev environment again -- but it looks like the newer WDK (for 8.1) makes life a lot easier. I'll see if I can get an updated build of ProcessHacker out soon.
Cheers!
On this front, is there any way to "selectively install updates" other than rushing to "Check Updates" and unchecking the ones we don't want, then immediately disable Windows Update afterwards? I'm concerned about downgrading to RT 8.0 and the auto 8.1 update automatically being installed, since RT auto-installs updates and I want to install the other updates...
They removed the UI for auto update behavior, but the registry value is still there and still works the same way. My tablet is set to notify me when there's updates but to not install anything (I forget if I told it to download them or not). You can also just turn off the automatic update feature entirely, in which case you need to remember to check manually as it won't prompt you.
Other than the awful 8.1 auto-grade "updates" already mentioned, there was an optional update released back in June, kb2962407, that seemed to break the jailbreak for me until I uninstalled it:
http://forum.xda-developers.com/win.../kb2962407-causing-jailbreak-to-hang-t2803626
It's no longer in the optional updates list so I'm not sure whatever happened to it. No one else ever mentioned anything about it that I saw, so perhaps my issue may have been a fluke, or nobody else ever bothered to install it. Jailbreak still works great on my Surface RT, and this is the only time I've seen anything that broke it (knock on wood).
Hi folks,
Has anyones Z3 started randomly rebooting on its own?
Its done it 4 times in the last hour. Battery life is at 30%
Thanks
Mine none have this issue. Try using pc companion or flashtool repair your phone.
Sent from my D6653 using XDA Free mobile app
KurtHoyle said:
Hi folks,
Has anyones Z3 started randomly rebooting on its own?
Its done it 4 times in the last hour. Battery life is at 30%
Thanks
Click to expand...
Click to collapse
No I haven't seen that on mine, and I have run my battery down numerous times. As suggested above, I would look at restoring your phone or factory resetting it
I have gone through 3 Z3s and on 4th now, all were replaced for cosmetic reasons, none had any stability issues. All were rock solid no crashes.
Try removing all non factory installed apps, if that does not work try resetting to factory defaults. If that also fails then maybe your firmware/NAND got corrupted... happened to me with an HTC One X before (NAND). I highly doubt the worst case scenario though.
Thanks everyone. Ill do a factory reset today and see if that helps
Cheers
Bumping this thread to see if anyone else has had this issue... I've Googled, and some users have experienced this issue. So far I have factory reset my phone, but that has yet to work.
I'm getting random crashes, sometimes using the phone and sometimes while it's just sitting there... It happens like at least 10-15 times a day and I've only had my phone for like 4 days.
Toneekay said:
Bumping this thread to see if anyone else has had this issue... I've Googled, and some users have experienced this issue. So far I have factory reset my phone, but that has yet to work.
I'm getting random crashes, sometimes using the phone and sometimes while it's just sitting there... It happens like at least 10-15 times a day and I've only had my phone for like 4 days.
Click to expand...
Click to collapse
Same. Struggling.
i had my first random reboot yesterday phone was just sitting there.
hasn't done one since.
I've had the phone for 4 days (Software 23.0.A.2.93) and it randomly reboots 2-3x a day.
I've had the same problem as well. Sent it to Sony for repair. They said it had something to do with the software. Asked for more information, they said an app was causing it (I use normal applications: FB, Line, reddit, skype, dropbox). Sony said they "repaired" my phone by erasing all my data and re-installed the firmware. Happened AGAIN TODAY. BTW it shows up as a "system restart" in the diagnostics menu. Is this the same for everyone experiencing this? Btw i used the pc companion to repair my phone as you have mentioned before sending it to Sony; that DIDN'T work either
I'm seeing this maybe once every 1-2 days, after reading the program list above I'm trying removing Skype to see if that's causing issues.
Ian
ke7in said:
I've had the phone for 4 days (Software 23.0.A.2.93) and it randomly reboots 2-3x a day.
Click to expand...
Click to collapse
Suggest you to update to .98 or even .105, do a factory reset and check how it works afterwards.
sxtester said:
Suggest you to update to .98 or even .105, do a factory reset and check how it works afterwards.
Click to expand...
Click to collapse
So you presume that its a problem with software and not hardware is that correct?
kiminoir said:
So you presume that its a problem with software and not hardware is that correct?
Click to expand...
Click to collapse
Yes, correct. I'm running on .98 since day one and never had any unintended reboots at all. As we speak, my Z3C runs since about 10 days.
Sent from my D5803 using XDA Free mobile app
sxtester said:
Yes, correct. I'm running on .98 since day one and never had any unintended reboots at all. As we speak, my Z3C runs since about 10 days.
Sent from my D5803 using XDA Free mobile app
Click to expand...
Click to collapse
How do I do that though? There are now more issues now. The necessary phone applications themselves are now crashing (ie. contacts, clock, walkman) I've included a photo for you. My current plan is to send my phone back to Sony for repair once again. The problems seem to appear out of nowhere.
Thanks in advance
kiminoir said:
How do I do that though? There are now more issues now. The necessary phone applications themselves are now crashing (ie. contacts, clock, walkman) I've included a photo for you. My current plan is to send my phone back to Sony for repair once again. The problems seem to appear out of nowhere.
Thanks in advance
Click to expand...
Click to collapse
Please use the search function, it's been explained a countless times already: http://forum.xda-developers.com/z3/general/ftf-stock-firmwares-xperia-z3-models-t2886061
I did a repair (still on .93) and it seems ok since yesterday but we'll see. Here are the instructions Sony sent me:
Thank you for contacting Sony Xperia™ Online Support.
We have an extended guide that should help you fix the issue on your phone, please follow the instructions carefully:
Visit this link:
sonymobile dot com/us/tools/pc-companion/
Click on Download PC Companion
Run the software and install it
Turn the phone off and disconnect it from the computer
1. No matter what the program says do not connect the phone until you complete step 9
2. In the welcome screen you will see the different modules available for you including the "Support Zone" option. Click on "Start" below it.
3. On the next page Click on "Start" under "Phone Software Update"
At this point if you get an error stating that "Unable to install update components" or "Server is busy" , then please proceed to step 12
4. The program will say that there is no phone connected. Click on the option below that reads: "Repair my phone" the program will issue you a warning about the content that you will lose during the update
5. Choose the option to continue.
6. The program will issue a final message warning you of possible data lost during the update. Click on the checkmark and then on "Next".
7. After that, the program will download the necessary information (5 to 6 minutes) and it will present you with a list of phones.
8. Choose your phones model from the list then click on "Next" then you will see a new section telling you how to connect the phone. (don't connect it yet)
At this point the phone must be off and disconnected from the PC.
9. Connect the cable to the PC not to the phone, then while pressing and holding the indicated button (in the steps on screen an specific button will be shown for you to press on the phone) connect the cable to the phone and keep holding the indicated button until the program says "the update of your phone has started..." (in some cases a message of "Installing drivers" will appear before the message of "the update of your phone has started..." is shown.)
10. If you failed to follow the steps correctly the phone will turn on and it will request that you "Proceed with the following steps, slide down the notification bar", If this happens disconnect the phone from the cable, turn it off and repeat from step 9).
11. If the phone is connected properly, PC Companion will proceed with the update ( It will tell you to let go of the back key) then wait for the update to finish and follow instructions on screen to disconnect the unit.
Dear Customer,
12. If "Unable to install update components"
1. Close PC Companion
2. Install Java from: java dot com
3. Start PC Companion again and try to do the software unlock process once more.
Note: If you wish only to update the unit wait for the program to open and then select the quick link on the upper left corner that says "Update Phone/Tablet" and follow the instructions to perform the update. (the PC may request for the phone to be placed in Mass Storage mode. Do this by going into Settings>Xperia>Connectivity>USB connection mode)
Click to expand...
Click to collapse
Same here.
i have the same problem but i have rooted min with Glade rom, works fine except for the random reboot.
Hi all,
2 days ago I purchased brand new Z3 and today the device started restarting every 15-20 minutes. There are no external factor that seems to be causing it – the phone restarts without being in use. What I’ve notice is that it’s doing a “Soft Reboot”.
Some additional info – after the phone was turned on for first time it asked for an Software Update to Android 5.0. After installation it rebooted and asked for another update. The heaviest app that is currently running is Facebook.
I would really appreciate any suggestions as I would like to avoid waiting for two weeks for the service centre to do something, that I can also do.
Thanks!
KurtHoyle said:
Hi folks,
Has anyones Z3 started randomly rebooting on its own?
Its done it 4 times in the last hour. Battery life is at 30%
Thanks
Click to expand...
Click to collapse
...
Allright, I finally got my Honor 8! FRD-L09 in Belgium through V-mall.:victory:
I got a notice there is an update available. I am currently on EMUI 4.1. On my older devices I never update and just flash higher versions instead.
Anything I should do before initiating this update?
Are there any reasons not to update (yet)?
Is there anything I should do like backups and all?
I'm currently trying to do an adb backup but I forgot what exactly is included in that. It's not the same as a nandroid is it?
Some weeks ago I saw some people need some files still. Forgot where it was or which wording was used. Does anyone still need something from a new user? Likely the request has already been filled with more people having the device by now.
I'm going to check out this thread later and mess around with xposed and those cool things.
Anything else I need to know about my device?
Thanks guys! Let's make this device awesome!:highfive:
ota updates
miva2 said:
Allright, I finally got my Honor 8! FRD-L09 in Belgium through V-mall.:victory:
I got a notice there is an update available.
Anything I should do before initiating this update?
Are there any reasons not to update (yet)?
Thanks guys! Let's make this device awesome!:highfive:
Click to expand...
Click to collapse
Hi miva2
Since getting my Honor 8 i've had a couple of ota updates which have installed fine (apart from installing some chinese app updates, but that happened because my phone is the chinese version with a supplier-installed mod to mostly make the phone english)
as far as I'm aware an OTA update should preserve all of your data and settings, but it can't hurt to regularly back up your personal files.
For this I use a nice little app called MyPhoneExplorer
not sure what the difference is between an adb and nandroid backup other than what I read here http://android.stackexchange.com/questions/48833/whats-the-difference-between-a-nandroid-backup-and-an-adb-backup
Hope that helps
The initial thing is to charge your mobile above 70% and take a backup of your data. In the future if any problem arises, then the first thing to do is the Factory data Reset.
So its better to wipe the cache and install the update.
Also remember your Google Password which is used for Login into your Android Google Account. All the Honor mobiles released in 2016 has Factory Data Protection. So you need to remember the username and password u used for logging in this mobile previously.
Before OTA update, check the instructions on screen, if any, usually it will show you to charge your phone above 50%. For major update, it will also remind you to backup your data (but I've never done that...)
Just make sure to have 70% of battery, or plug it in the charger
Thanks for the tips!
I'll try to make an adb backup again later. Had trouble finding the device through adb. Probably need some drivers or something.
vsriram92 said:
Also remember your Google Password which is used for Login into your Android Google Account. All the Honor mobiles released in 2016 has Factory Data Protection. So you need to remember the username and password u used for logging in this mobile previously.
Click to expand...
Click to collapse
Cool, I didn't know that.
Plug the charger in and update, ive nerver experienced an Honor Ota delete data
HonorCasper said:
Plug the charger in and update, ive nerver experienced an Honor Ota delete data
Click to expand...
Click to collapse
OTA update won't delete the data. However it is recommended to reset once after the update.
So taking backup is useful.
vsriram92 said:
OTA update won't delete the data. However it is recommended to reset once after the update.
So taking backup is useful.
Click to expand...
Click to collapse
You're absolutely right there bro
It's obvious, it became a habit in me
It is recommended that you update to the latest version as soon as possible. After you receive an update notification, you can enter Settings > Updater to check the update and choose whether to update. It is recommended that you update using a Wi-Fi connection.
Normally, system updates will increase your phone's performance, and strengthen personal privacy and data security protection. They also provide new features, therefore it is recommended that you update as soon as possible. If you do not update, you can still use your current system normally.
Performing a system update will not clear user data, but in order to protect your data security, it is recommended that you back up your data before updating. (NS)
PalakMi said:
It's obvious, it became a habit in me
Click to expand...
Click to collapse
Yeah youre right, i just become a part of updating
Okay so backup is just for user data. nandroid is not needed.
With reset I assume you guys mean a factory reset and not just a reboot.
Hope I get my sim card soon (mine was too big) so I can actually start using this phone instead of having it decorate my bedside table.
miva2 said:
Okay so backup is just for user data. nandroid is not needed.
With reset I assume you guys mean a factory reset and not just a reboot.
Hope I get my sim card soon (mine was too big) so I can actually start using this phone instead of having it decorate my bedside table.
Click to expand...
Click to collapse
First of all, you got a sweet bedside decoration dude:good:
Yes just data backup, and Yes, factory reset
miva2 said:
With reset I assume you guys mean a factory reset and not just a reboot.
Hope I get my sim card soon (mine was too big) so I can actually start using this phone instead of having it decorate my bedside table.
Click to expand...
Click to collapse
Yes we mean the factory reset.
In the meantime you get the SIM, you can update through Wifi (if available).
SIM is not mandatory to update.
beakerav said:
Hi miva2
Since getting my Honor 8 i've had a couple of ota updates which have installed fine (apart from installing some chinese app updates, but that happened because my phone is the chinese version with a supplier-installed mod to mostly make the phone english)
as far as I'm aware an OTA update should preserve all of your data and settings, but it can't hurt to regularly back up your personal files.
For this I use a nice little app called MyPhoneExplorer
not sure what the difference is between an adb and nandroid backup other than what I read here http://android.stackexchange.com/questions/48833/whats-the-difference-between-a-nandroid-backup-and-an-adb-backup
Hope that helps
Click to expand...
Click to collapse
I have a Chinese Honor 8 and just finished uninstalling the Chinese apps and setting up Google. Was going to do an OTA update, what do you mean by it installed some chinese app udpates? You mean the Chinese apps reappeared?
spix123 said:
. . . what do you mean by it installed some chinese app udpates? You mean the Chinese apps reappeared?
Click to expand...
Click to collapse
Sorry, bad use of language from me.
Not complete apps, but every now and then stuff pops up on screen, all in Chinese, that I don't understand, one such screen must be some media portal as there was hyperlink pictures (bit like a Chinese version of YouTube) but selecting returns server error.
I accidentally installed last ota and the next update notification screen that popped up was also in Chinese language. All my location settings are English so I figured the Chinese stuff must be updated system files because they started appearing after I installed updates (guess that's why supplier recommended no ota)
beakerav said:
Sorry, bad use of language from me.
Not complete apps, but every now and then stuff pops up on screen, all in Chinese, that I don't understand, one such screen must be some media portal as there was hyperlink pictures (bit like a Chinese version of YouTube) but selecting returns server error.
I accidentally installed last ota and the next update notification screen that popped up was also in Chinese language. All my location settings are English so I figured the Chinese stuff must be updated system files because they started appearing after I installed updates (guess that's why supplier recommended no ota)
Click to expand...
Click to collapse
I did one OTA update from b106 -> b135. Next one is to b160 and says it includes 3 patches. I didn't get any chinese popups or anything. I uninstalled most of them and disabled notifications/autostart on the ones remaining.
What version are you on and hows your standby time? Just testing the phone a bit now and standby isn't looking too good. Left it overnight with Wifi on and it lost around 10%. Wondering if its the rom, some setting or normal?
spix123 said:
. . . What version are you on and hows your standby time? Just testing the phone a bit now and standby isn't looking too good. Left it overnight with Wifi on and it lost around 10%. Wondering if its the rom, some setting or normal?
Click to expand...
Click to collapse
I'm on version 160, can't resist installing to see what gets improved, but I think it only a matter of time before an ota install breaks this e-mod-rom, I guess when that happens I'll just have to either pay e-to-talk for replacement rom or factory reset
I leave phone overnight with wifi on and bluetooth on (linked to my pebble wristwatch) and tend to lose 3 to 4 % by morning, really impressed with battery life. Have you found battery management app? I'm sure you would have, it's got some nice features for saving power
beakerav said:
I'm on version 160, can't resist installing to see what gets improved, but I think it only a matter of time before an ota install breaks this e-mod-rom, I guess when that happens I'll just have to either pay e-to-talk for replacement rom or factory reset
I leave phone overnight with wifi on and bluetooth on (linked to my pebble wristwatch) and tend to lose 3 to 4 % by morning, really impressed with battery life. Have you found battery management app? I'm sure you would have, it's got some nice features for saving power
Click to expand...
Click to collapse
It maybe because I had no sim in it and the phone was constantly checking for it. Turned on airplane mode and left for 8 hours, it lost 1%. Now trying airplane mode with Wifi on.
How do you know the rom is modded?
Hello guys, my fingerprint reader is not always working as it is intended. If it is working unlocking my phone isn't a problem, it is as fast as it should be. Also guestures on the fingerprint reader are working fine - then sometimes the fingerprint reader doesn't recognize that I put a finger on it. No vibration and no unlocked phone (obiviously) and I have to enter my pin to enter my phone.
Reboot doesn't resolve this issue, as it comes back a few minutes after restart. Phone is about a month old and on the latest Emui firmware. Any suggestions beside full wipe and returning to service center?
Thanks in advance!
The weird thing is that it doesn't even vibrate as to show that it didn't recognized the fingerprint, but it just doesn't show signs of life... And neither a reboot solve the issue instantaneously? So strange. Tell me something more, did you updated OTA, or with Firmware Finder? You have something like Greenify installes? Other?
RedSkull23 said:
The weird thing is that it doesn't even vibrate as to show that it didn't recognized the fingerprint, but it just doesn't show signs of life... And neither a reboot solve the issue instantaneously? So strange. Tell me something more, did you updated OTA, or with Firmware Finder? You have something like Greenify installes? Other?
Click to expand...
Click to collapse
No a reboot doesn't change anything - there is no app installed for battery optimization or a taskkiller or something similar. I've got the phone a month ago, everything else works flawless. I did the first update to android 7 via sd card and received another ota update some days ago. Every update was an official update from Huwaei/Honor, i have a c432 BLN-L21 device with no carrier lock or branding. Build: BLN-L21C432B365, Security patches from 1st August.
Just checked my build, man, and... we're exactly on the same, identical build. I only have to download the update and apply it because I'm still on B360, thing that I'll do probably tomorrow (even if I'd like to download the full package of 2,45GB and not only the upgrade of 547M, I'd like to keep the package for future eventualities since that Huawei removed firmwares from their site). Don't know if the first update via SD card could be responsible somehow or not of this, you remember if the update made by SD was the correct version of firmware that was matching with your initial build?
Does it happen mostly after you take out your phone from pocket and try to unlock with FP? Or some other behaviour while unlocking normally
shashank1320 said:
Does it happen mostly after you take out your phone from pocket and try to unlock with FP? Or some other behaviour while unlocking normally
Click to expand...
Click to collapse
It makes no difference if I take it out of the pocket or it is just lying around before trying to unlock it. No other faulty behaviour beside the unlocking problem.
@RedSkull23 I'm pretty sure I had the right firmware and that it was matching the product exactly.
gent0r said:
@RedSkull23 I'm pretty sure I had the right firmware and that it was matching the product exactly.
Click to expand...
Click to collapse
Well this tightens the circle of possible causes of this, did your phone ever dropped? I'm starting to think at an hardware problem now...
Try performing a hard factory reset but wipe the Cache Partition first. Be sure to back up all your data before you do this. That should help with any software conflicts.
RedSkull23 said:
Well this tightens the circle of possible causes of this, did your phone ever dropped? I'm starting to think at an hardware problem now...
Click to expand...
Click to collapse
Seems more of a hardware issue or may be a factory reset can help him here
Even I had the same problem. So the solution is to delete your previous finger print and than enable a new one. Hope this helps....