I was reading on one of the post here on how to unbrick the samsung galaxy s3 sgh-t999 t-mobile version
http://forum.xda-developers.com/showthread.php?t=2439367
I came across the same problem as user n2pc tech
User n2pc tech had this problem
BOOT RECOVERY MODE
CHECK BOOT PARTITION.
COPY FROM T-FLASH.
BOOT RECOVERY..
FLASH WRITE FAILURE
ODIN MODE
PRODUCT NAME: SGH-T999
CUSTOM BINANRY DOWNLOAD: NO
CURRENT BINARY: Samsung Official
SYSTEM STATUS: NONE
QUALCOMM SECUREBOOT: ENABLE
I can't seem to get the phone into download mode (power+volume down+home) or via adb
It just sits there and Odin wouldn't do anything.
There seems to be no solution at this point in time as I have completely finished reading that entire thread. Would anyone have any idea(s)
Same boat here. Need help
Hi I'm having the same issue with my sister's S3. T999.
Same error message. Anyone?
Stuck in same boat as you.
Ityperx said:
I was reading on one of the post here on how to unbrick the samsung galaxy s3 sgh-t999 t-mobile version
http://forum.xda-developers.com/showthread.php?t=2439367
I came across the same problem as user n2pc tech
User n2pc tech had this problem
BOOT RECOVERY MODE
CHECK BOOT PARTITION.
COPY FROM T-FLASH.
BOOT RECOVERY..
FLASH WRITE FAILURE
ODIN MODE
PRODUCT NAME: SGH-T999
CUSTOM BINANRY DOWNLOAD: NO
CURRENT BINARY: Samsung Official
SYSTEM STATUS: NONE
QUALCOMM SECUREBOOT: ENABLE
I can't seem to get the phone into download mode (power+volume down+home) or via adb
It just sits there and Odin wouldn't do anything.
There seems to be no solution at this point in time as I have completely finished reading that entire thread. Would anyone have any idea(s)
Click to expand...
Click to collapse
Stuck in same boat. Have you found an answer to this problem? I've looked all over but have not found anything.
Help Needed!!
My Samsung SGH-T999 has stuck in Odin mode,
as i boot it, Samsung logo appears for a split/second and disappears, and boots into odin mode. with error displaying couldn't do a normal boot,
Recovery Boot : No. Various error i got in odin: write operation failed, on phone flash read failure.
<ID:0/004> <OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVDMD5_T999TMBDMD5_T999UVDMD5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Related
Hi guys,
as the title said i got a problem with running my tab2 in download mode.
when i run the device in dl mode my pc (win 7) shows it as samsung modem, and if i start in recovery mode it shows as adb device.
odin can find the device anyway but failed on any flash process.
when i run in dl mode i get several outpot from the console on the device:
Odin download mode (protocol2.1)
Reason: Force Key
Secue Mode: Secure
Check Signature: Check
Custom Binary Downloads: no (0counts)
Current Binary: Samsung official
waiting usb cable...
connected press the start of odin3!!
so device is seen in odin i choose the .md5 and get following odin output:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-espresso10rf-espresso10rfxx-gtp5100.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
after this my tab dl screen tells me following:
fail to download 8/sos data:2569... and so on
tegra_nand_write Error to download partition_odin err0xffffffff
after this i have to do a factory reset with recovery mode to get the tab working again because it want to connect to kies and make a force restore
i already flashed several mobile phones so i think i know what i have to do but with this tab... im just confused
i already tried to setup several drivers manually, tried pc´s with kies and pc´s which never had kies installed before...same issue
I tried several .md5 files
so my question is now... what am i doing wrong? how can i get the adb driver working in download mode not in recovery
hope someone can help me
cassialla said:
Hi guys,
as the title said i got a problem with running my tab2 in download mode.
when i run the device in dl mode my pc (win 7) shows it as samsung modem, and if i start in recovery mode it shows as adb device.
odin can find the device anyway but failed on any flash process.
when i run in dl mode i get several outpot from the console on the device:
Odin download mode (protocol2.1)
Reason: Force Key
Secue Mode: Secure
Check Signature: Check
Custom Binary Downloads: no (0counts)
Current Binary: Samsung official
waiting usb cable...
connected press the start of odin3!!
so device is seen in odin i choose the .md5 and get following odin output:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-espresso10rf-espresso10rfxx-gtp5100.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
after this my tab dl screen tells me following:
fail to download 8/sos data:2569... and so on
tegra_nand_write Error to download partition_odin err0xffffffff
after this i have to do a factory reset with recovery mode to get the tab working again because it want to connect to kies and make a force restore
i already flashed several mobile phones so i think i know what i have to do but with this tab... im just confused
i already tried to setup several drivers manually, tried pc´s with kies and pc´s which never had kies installed before...same issue
I tried several .md5 files
so my question is now... what am i doing wrong? how can i get the adb driver working in download mode not in recovery
hope someone can help me
Click to expand...
Click to collapse
brother i cannot remember but there is a thread here which installs adb on every pc so you can search or try it
So I was previously running the MF3 baseband on my SGH-I337 (ATT) and couldn't install any custom ROMs until I tried safestrap. I installed the Google Play Edition ROM and it worked successfully, except the WiFi wouldn't turn on. I could have flashed modem files but I was advised multiple times not to do so. Anyways, I was removing the ROM through safestrap and accidentally wiped my system and all its files I think. Now my phone is stuck in a bootloop (constant Samsung logo) and I can't recover with ODIN because I get an error (shown below). Also, I could only find a TAR file which ends with either MK2 or MDL, my phone was previously MF3, could this be the cause of any problem? Any fixes?
Additional Info:
1) I cannot boot into stock recovery, I'm always forced into download mode.
2) ODIN gives the error everytime I try to flash the stock ROM that I downloaded.
3) I've tried flashing the 16GB PIT file with little luck, the operation finished successfully but I'm still not able to flash anything else because:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I'm quite new to all of this, any help is greatly appreciated. Sorry if I'm leaving out information, just ask if needs be.:laugh:
My i337 is doing the same thing, except I started on mk2. I see tons of folks asking about complete write fail on google, so I know this is a bigger issue that hasn't been identified yet...but when I get this POS working, I am selling it and NEVER buying anything with a locked bootloader (or the AT&T logo) again. I wish I had researched better and chosen a tmobile S4 to use on at&t.
I got the exact same error like you do in Odin with flashing a new PDA / Recovery. Cannot get rid of error messages, status 7, fail in odin and so on, but my phone isnt in boot loop like yours..
Hello guys,
I hope you are all doing well and i am here to see if you are able to help me. So, i tried to install TWRP and apparently i did it with the wrong version because now my phone is stuck in the Logo screen with the red message reading that recovery is not seandroid enforcing. I have been reading around and people say i should go into recovery mode and try to factory reset, the problem is that i can't go into recovery mode since pressing volumeup/home/power doesn't work, the only thing that works is me pressing volumedown/home/power which brings me into Download mode, so i looked around and found out that an easy solution for this is to download your stock rom and flash it with ODIN3. The problem here is that with OI1 update, Odin flash is not working properly so when i try to install my stock rom, which i am guessing is this one: G920PVPU2BOH1_G920PSPT2BOH1_G920PVPU2BOH1_HOME.tar Odin prompts me with this:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
I am really desperate here as i don't know what to do anymore, i flashed V-Kernel-925P-BOFE-071915 and it installs successfully but this doesn't seem to help at all. Before i tried TWRP my phone was working fine, rooted with UniKernel_v8-0001-BOH1-920P-091215, what i was trying to do was install TWRP so i could install a custom ROM since Sprint one was full of security checks.
Now i can't even access my phone anymore which has me really concerned.
If anyone has any clue of what i should do please lend me a hand, i will certainly thank you for it.
Also, does anyone know how to turn off the phone?....no button combo seems to work besides vol-/home/power, and i have no idea how to turn it off from the seandroid logo screen.
You can get into recovery by using home+volume down +power. As soon as the screen blinks, quickly go to home+volume up +power. Also I have the tar stock recovery if that helps
It appears you are trying to flash an S6 rom on your S6 Edge.
jlharing99 said:
It appears you are trying to flash an S6 rom on your S6 Edge.
Click to expand...
Click to collapse
You can flash an S6 Edge Rom on a S6 but you have to change the kernel before you boot.
I could be wrong but I think I got him all sorted out with this problem.
Sorry to bump but I have a similar problem, is there a fix?
Samsung Galaxy S7 (SM-G930T) T-Mobile
Info on ODIN Download screen
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-G930T
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
FRP LOCK: On
WARRENTY VOID: 0x0
QUALCOMM SECUREBOOT: Enabled
RP SWREV: B4(2, 1, 1, 1, 1) K1 S3
SECURE DOWNLOAD: Enabled
I have referenced the guide I followed. GUIDE. I followed all the instructions. After root I used the Debloater and my phone was incredibly slow and inefficient. So, I used the fix V15. Yet again, slow, hot and a whole host of problems. So, I follow the unroot guide. I continued encounter this error on odin when attempting to unroot.
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1205)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And this error on my phone:
Code:
SW RV CHECK FAIL: [system]Fused 3>Binary 1
After trying at least 4 different AP's
Code:
TMB-G930TUVS2APB8-20160317155535
TMB-G930TUVU2APC8-20160402115527
TMB-G930TUVU1APB6-20160310103828
TMB_G930TTMB4BQB1
I got frustrated and Held any button I could to get that stupid screen to go away. I was met with "An error has occured while updating the device software. Use the Emergency recovery function in the Smart Switch PC software. So, I go to do that. And the smart switch software does not support my phone. So, I boot into Recovery mode Wipe Cache, Wipe everything I can and try to reboot and I can only go from DOWNLOAD mode to recovery mode. I read somewhere on here that you can't Rollback firmware so I try the newest firmware and maybe that will work. I encounter no issues in ODIN and no issues on my phone Once my phone reboots it goes to the Samsung Galaxy S7 splash screen with the Unlocked lock and doesn't do anything past that. So I try to boot to recovery mode and that's when I get caught in a loop. My phone went from a flashing "Recovery booting" then if I tap a bunch of VOL UP/DN HOME and POWER combinations It will go to splash screen and flash the splash screen numerous times. I can now get it back to Download mode after messing around with it. But I have no idea what I need to do.
If I need to provide any more information let me know.
How Do I mark this as solved? I Used ODIN to update my bootloader to the newest version. then used the most current AP CP and CSC there is. It's booted up and installed. Now I'm just restoring and Going to restart to make sure everything is working correctly.
Hey guys, I've come into possesion of a Galaxy Note 5 that my cousins seemed to have messed with. A long while back I played with flashing firmware etc on my own phones so I assume that is what happened here. It attempts to start up, getting to the Note 5 splash screen then black screens, then splash screen and so on. I couldn't stop it without a hard reset (Volume down + Lock).
The phones details:
Samsung Galaxy Note 5 (was known working no more than a week ago) Product name: SM-N920I I saw version 6.0.1 somewhere in the menus, I believe this to be the current version of android available to Note 5 phones in Australia? I cant find the build number anywhere that I can access.
Has anyone got any clues? I'll include the ODIN screenshot and text from the phone in download mode. It may also be worth noting I can get into recovery mode, but not safe mode. I've tried wiping partitions etc, nothing there worked.
Download Mode pre failed flash:
ODIN MODE
DOWNLOAD SPEED: FAST
PRODUCT NAME: SM-N902I
CA_ TYPE: CA_3
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
FRP LOCK: OFF
Secure Download : Enabled
KNOX WARRENTY VOID: 1 (0x0500)
RP SWREV: B:3 K:0 S:1
I gain "SECURE CHECK FAIL : (BOOTLOADER)" after the failed ODIN flash.
Recovery menu shows -
Android Recovery
MMB29K.N920IDVS3BQA3
samsung/nobleltedv/noblelte
6.0.1/MMB29K/N920IDVS3BQA3
user/release-keysAt the bottom -
Supported API: 3
dm-verity verification failed...
I can't post a screen shot of ODIN due to an inactive account, so I will copy paste that text here as well.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1205)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> cm.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
Like I said above, the phone was working fine last week, saw it myself at a family get together. He said something about not being able to play Mario Run, and I've heard there are issues with rooted devices with Mario Run so perhaps hes tried to unroot the device and messed up the process?
I'm fairly tech savvy, so I should be able to fix it. I just don't know where to really go from here thanks to lack of experience.
How screwed is this phone?
EDIT: I also just want to state that I couldn't find any info about the "SECURE CHECK FAIL : (BOOTLOADER)" message anywhere. A lot about aboot and other stuff, but no bootloader.