Hello guys,
I hope you are all doing well and i am here to see if you are able to help me. So, i tried to install TWRP and apparently i did it with the wrong version because now my phone is stuck in the Logo screen with the red message reading that recovery is not seandroid enforcing. I have been reading around and people say i should go into recovery mode and try to factory reset, the problem is that i can't go into recovery mode since pressing volumeup/home/power doesn't work, the only thing that works is me pressing volumedown/home/power which brings me into Download mode, so i looked around and found out that an easy solution for this is to download your stock rom and flash it with ODIN3. The problem here is that with OI1 update, Odin flash is not working properly so when i try to install my stock rom, which i am guessing is this one: G920PVPU2BOH1_G920PSPT2BOH1_G920PVPU2BOH1_HOME.tar Odin prompts me with this:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
I am really desperate here as i don't know what to do anymore, i flashed V-Kernel-925P-BOFE-071915 and it installs successfully but this doesn't seem to help at all. Before i tried TWRP my phone was working fine, rooted with UniKernel_v8-0001-BOH1-920P-091215, what i was trying to do was install TWRP so i could install a custom ROM since Sprint one was full of security checks.
Now i can't even access my phone anymore which has me really concerned.
If anyone has any clue of what i should do please lend me a hand, i will certainly thank you for it.
Also, does anyone know how to turn off the phone?....no button combo seems to work besides vol-/home/power, and i have no idea how to turn it off from the seandroid logo screen.
You can get into recovery by using home+volume down +power. As soon as the screen blinks, quickly go to home+volume up +power. Also I have the tar stock recovery if that helps
It appears you are trying to flash an S6 rom on your S6 Edge.
jlharing99 said:
It appears you are trying to flash an S6 rom on your S6 Edge.
Click to expand...
Click to collapse
You can flash an S6 Edge Rom on a S6 but you have to change the kernel before you boot.
I could be wrong but I think I got him all sorted out with this problem.
Sorry to bump but I have a similar problem, is there a fix?
Related
hello all,
I'm a noob and i messed up my note edge. I rooted it on stock kk 4.4.4 rom from Rogers and installed superuser and twrp. I wanted to do a factory reset through the settings and reset and erase everything but it won't allow me to. Every time i select erase it would just do nothing. Do i thought I'd be smart and enter twrp by holding volume up, home, and power button then wipe everything. Now when i power on the phone it just boot loops with the original Samsung galaxy note edge splash screen. I am unable to find the original rom for my N915W8 Rogers phone so i read I'm done forums a T-Mobile rom should work. I downloaded a lollipop T-Mobile rom and tried to flash it with Odin but comes up as fail. I tried to put the zip file into my external micro sd card and use twrp to install and it failed again. Any help is greatly appreciated. My end goal is to be able to get the lollipop Rogers rom with root back on my phone.
Thanks
Enter Download Mode and use Odin to restore the stock ROM.
Thanks for the reply. I tried ODIN but unable to flash. It fails right away.
This is what I get:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N915TUVU1BOG2_N915TTMB1BOG2_N915TUVU1BOG2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl1.mbn
<ID:0/004> rpm.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any other clue? I think the problem is I have no data in my phone. I am thinking it needs some base to work off of. Please don't laugh at my logic lol.
So I was following this guide :
http://forum.xda-developers.com/gal...-xtrestolite-pure-edition-1-0-beta-1-t3082467
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-zeroflte-zerofltexx-smg920f.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
And I think I flashed CF-Root correctly. Tried to boot, Recovery is not seandroid enforcing. I then flashed TWRP 2.8.7.1 (the .img one) and now it proceeds to recovery after boot screen.
I tried restarting to system with TWRP and it went into a bootloop.
Am I on the right track? I mean is it supposed to be like that until I do a factory reset? I'm scared cause the ROM is still downloading lol how do I put it in the device's internal memory? Will I be able to in Download Mode?
On a PC running Windows XP right now, Samsung's USB Drivers don't seem to work whatsoever. I'll try it on my laptop and we'll see.
(p.s. should I have opted for the one-click rooting and stuff? Idk the guide tells me to do it via Odin so yea lol)
Since you were on 5.0.2 you could've used the PingPongRoot to easily root your phone. I did that but then after a while I thought I want a custom ROM so I updated to 5.1.1 and tried to use odin to root my phone but got the same issue as you.
After a few hours of struggeling I got out of the bootloop by doing an emergency software recovery from Smart Switch. However I'm not sure if it will recover to 5.0.2 or download the latest 5.1.1 in your case.
Nonetheless when I got my phone to work again I just flashed UniKernel with TWRP and then I was rooted.
I wont touch odin ever again I'm too nooby for that and it caused me to panic so hard with that goddamn bootloop.
I hope you get it solved!
Hey guys; New to the forums; Read a few guides nothing has really helped so far but I could just have missed something;
So what happened is;
I have succesfully taken all the bloatware off my s6 Edge; I was trying to do the same for the misses phone (Galaxy s6) Yes i made sure to get the right firmware
I downloaded from sammobile.com the G920I XSA so i could get rid of her telstra bloatware. However halfway threw the installation (Odin) it said failed and the phone was stuck in download mode for ages; I decided to just try a reset (after about 45 - 1hr) then it started booting up with a ! saying an error has occurred while updating the device software Use the Emergency Recovery function in the Smart Switch PC software;
Which I have tried doing; However it keeps getting to about 1 or 2% of the installation (yes it has finished the download read something on here about people getting stuck at 51% download) Then it asks me for a recovery code from a previous computer; I bought this phone used off someone with all the stock bloatware from telstra so I dont have the recovery code; How can I get around this ? I dont have their phone number either as it was on my old sim which didnt fit into this phone and I have already given my other phone away...
As of this min I am downloading the telstra version of the firmware again, Will this fix it ? and then will I be able to put the XSA firmware on ?
Thanks for any help
Appreciate it
EDIT...
This is what I get in odin
Code:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> cm.bin
<ID:0/004> boot.img
<ID:0/004> __XmitData_Write
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
whipz said:
Hey guys; New to the forums; Read a few guides nothing has really helped so far but I could just have missed something;
So what happened is;
I have succesfully taken all the bloatware off my s6 Edge; I was trying to do the same for the misses phone (Galaxy s6) Yes i made sure to get the right firmware
I downloaded from sammobile.com the G920I XSA so i could get rid of her telstra bloatware. However halfway threw the installation (Odin) it said failed and the phone was stuck in download mode for ages; I decided to just try a reset (after about 45 - 1hr) then it started booting up with a ! saying an error has occurred while updating the device software Use the Emergency Recovery function in the Smart Switch PC software;
Which I have tried doing; However it keeps getting to about 1 or 2% of the installation (yes it has finished the download read something on here about people getting stuck at 51% download) Then it asks me for a recovery code from a previous computer; I bought this phone used off someone with all the stock bloatware from telstra so I dont have the recovery code; How can I get around this ? I dont have their phone number either as it was on my old sim which didnt fit into this phone and I have already given my other phone away...
As of this min I am downloading the telstra version of the firmware again, Will this fix it ? and then will I be able to put the XSA firmware on ?
Thanks for any help
Appreciate it
EDIT...
This is what I get in odin
Code:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> cm.bin
<ID:0/004> boot.img
<ID:0/004> __XmitData_Write
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
My bad, I didnt know you needed to restart computer after each Odin; Reset the computer and the phone and everything is working smoothly now; Just got to find the right stockfirmware without all that bloat crap
s5 Sport stuck on boot "samsung galaxy s5 sport" screen after stuck on sprint screen
Hello everyone. I am new to rooting and was working on rooting a Samsung Galaxy s5 sport yesterday.
I was able to successfully root it and flashed cwm onto it with Odin3, and was able to launch to recovery.
Next, I attempted to flash xposed framework, which caused the phone to boot to the sprint spark screen and get stuck (not a boot loop).
I attempted to flash stock firmware to the phone, but it failed each time, so I tried to erase all content and restore to factory settings with cwm, but even though it said it worked each time it would still boot to the sprint screen and then get stuck. Now, it doesn't even go to the sprint spark screen and stops at the Samsung galaxy s5 sport screen.
I can boot into both cwm recovery and bootloader, so odin is still an option. I tried flashing the stock 5.0 firmware onto the phone, which is what it ran on originally, but same fail in odin as follows:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
The phone also shows SW REV CHECK FAIL: [aboot]Fused 2 > Binary 1
Edit: also wanted to add that everywhere I look seems to have info for the s5. For whatever reason, the g900 models don't work the same as the g860 (sport) model and I am unable to see what to do.
Update: after trying to install a custom rom to see if it fixed the problem, nothing changed aside from the Kernal is not seandroid enforcing, set warranty bit: kernel message showing in the corner. I am assuming that the phone is missing the boot files, and since I cannot flash the stock with odin I am not sure what to do.
I also tried flashing the stock with CWM, but it also did not install, just saying installation failed.
download this and flash it in Odin
it sounds like you have a bad download
Hi all,
I have a Galaxy Note 10.1 (2012) which worked fine until one night I switched it off before bed. The next morning it doesn't boot up. It just shows the Samsung logo.
The machine won't go into recovery but starts to show the TWRP initial screen before going back to rebooting.
The machine will go into download mode and I have tried flashing stock a stock ROM and TWRP again but each time, ODIN reports a fail.
This is the log from ODIN when I try to flash the stock ROM:
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1101)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)[/SIZE]
I have very often flashed ROMs in the past without a problem. I had TAB Sensation on the Note and had been using this for quite a while, then this just happens without any obvious reason.
Any help would be so gratefully received.
Thank you.
Jason
Download again.
Sent from my SM-N920C using XDA-Developers mobile app
Thanks for this but what should I download again?
stock ROM # for your model .
Same problem, but with unrooted model on stock 4.4.2. Happened once before, when under guarantee, and Samsung fixed it. Issue in detail:
Switch on - stuck at 10.1 logo
Will restart into download mode
Won't restart into recovery
Windows 10 computers won't recognise it when attached ('unknown USB device'), so ODIN doesn't see it.
So I'm stuck - any suggestions? Thanks in advance.
Attempted remedies so far:
uninstalled Kies
installed Samsung drivers (various versions)
reinstalled Kies
Skipsoft Toolkit
I've got the exact same problem with mine, it started several months ago. I was about to toss it but figured I'd give it another shot after a coworker told me of this forum. He suggested loading a new firmware/OS via the micro SD card, although since it won't even really boot I'm not sure how I'm going to do that.
http://forum.xda-developers.com/showthread.php?t=2080366