Hellow friends
Sunday i want to install Gimlo on my tipo. I formated system partition and wipe data and factory reset. But i made a mistake, i clicked on install zip from sideload in place of install zip from sdcard, and cwm freezed, i reset my phone and boon, no cwn, no rom, just sony logo. I tried to install stock rom with ftf, i can enter in fastboot and flashmode but i can't flash rom, it gives me an error
Can you give me a fix for that situation. Thanx in advance!
(and sorry for my bad english)
striker14 said:
Can you give me a fix for that situation.
Click to expand...
Click to collapse
remove battery
press flash button
without removing your finger
connect when flashtool prompts you
and then install your battery
then remove your fiinger from flash button
good luck
Naney said:
remove battery
press flash button
without removing your finger
connect when flashtool prompts you
and then install your battery
then remove your fiinger from flash button
good luck
Click to expand...
Click to collapse
Phone can enter in flashmode, useless answer.
@OP:
Probably you need to install drivers.
Thanx for answers, but i finally save it, i locked bootloader with flashtool and i used pc companion to update the phone, now everything works!
Ketcchup said:
Phone can enter in flashmode, useless answer.
Probably you need to install drivers.
Click to expand...
Click to collapse
You're so kind buddy.
That is true.
I didn't notice that phone entered in flashmode.
Regards.
Related
I have a Sony XPERIA Tipo and I have recently installed the correct CyanogenMod but I installed it wrong as I didn't first use the boot image. I have tried Sony PC Companion but it cannot find the correct firmware for my device, I have also tried other ways but they require using USB debugging which unfortunately I cannot enable using my phone. Does anyone know a way I can turn it on with my PC?
If u can boot to flash mode u can use flash tool
Sent from my ST21i using xda premium
jhonny1525 said:
If u can boot to flash mode u can use flash tool
Sent from my ST21i using xda premium
Click to expand...
Click to collapse
I can boot into flash mode and fast boot but flash tool always comes up with this error when I try flashing:
Error in processHeader : 2 : The system cannot find the file specified.
longatom said:
I can boot into flash mode and fast boot but flash tool always comes up with this error when I try flashing:
Error in processHeader : 2 : The system cannot find the file specified.
Click to expand...
Click to collapse
Use pc companion and repair it using fastboot mode
Sent from my GT-S7562 using xda premium
akashpillai said:
Use pc companion and repair it using fastboot mode
Sent from my GT-S7562 using xda premium
Click to expand...
Click to collapse
This did not work as PC companion doesn't update a phone without flash mode enabled, and as I said before PC companion doesn't work
Try sony update service it is quite automated
Sent from my ST21i using xda premium
jhonny1525 said:
Try sony update service it is quite automated
Sent from my ST21i using xda premium
Click to expand...
Click to collapse
I have also tried this and it did not work
It would work with Sony Emma Flash Tool but it doesn't currently support my phone, thanks you those of you who tried to help me. If anyone has any other ideas then feel free to reply as it might be a while before Emma becomes V1 instead of Beta.
Use Flashtools but in this time try the next
pull the battery , connect (when the program ask) and hold the volume key till the program starts to flash
Sorry for my bad english
Did you manage to repair your phone? I am facing the same problem.
Yes I did, I found a stock .ftf and I used flashtool
Sent from my C6903 using xda app-developers app
Unbrick Tipo
I ran into this problem at night, and I tried out a LOT of suggestion, but nothing had work. So, I figured it myself...
History: updated JBMP ROM, and it's got bootloop, w/o CWM, or any recovery... Bootloader open. Flashtool sad: Error in processHeader : 22 : Device could not recognize command or Read error :31 : Attached device not working
1a: download Flashtool, install it
1b: find and download a Stock ftf, copy/move to Flashtool/Firmwares
2: Start Flashtool
3: click "Flash" symbol, choose Flashmode
4: select Stock ftf
5: make sure to CHECK under misc: "no final verification" AND "reset customization"
6: hit Flash button, and wait to prompted to connect phone
7: press and hold Vol- while connect phone to PC
Then the flash process should be starting, and finishing fine. This steps restored my bricked Tipo back to life. Just in case, re-root, and install CWM.
Warning: first boot take some times, be patient! Make sure to do another reboot after first boot up.
Hope it's help.
@D Sanya thanks a million tonnes buddy, your advice helped me revive my bootlooping xperia e. This is exactly I was looking for. May God Bless you.
Remington78 said:
@D Sanya thanks a million tonnes buddy, your advice helped me revive my bootlooping xperia e. This is exactly I was looking for. May God Bless you.
Click to expand...
Click to collapse
Glad to hear it! :good:
xperia j
I have same problem in my sony xperia j please help me
st26i
.
What's yout operating system?
these order steps are very important
when...:
FIRST 6: hit Flash button, and wait to prompted to connect phone
when u see notification to connect phone , then ...
SECOND 7: press and hold Vol- while connect phone to PC in flashmode
Help please
DSanya said:
I ran into this problem at night, and I tried out a LOT of suggestion, but nothing had work. So, I figured it myself...
History: updated JBMP ROM, and it's got bootloop, w/o CWM, or any recovery... Bootloader open. Flashtool sad: Error in processHeader : 22 : Device could not recognize command or Read error :31 : Attached device not working
1a: download Flashtool, install it
1b: find and download a Stock ftf, copy/move to Flashtool/Firmwares
2: Start Flashtool
3: click "Flash" symbol, choose Flashmode
4: select Stock ftf
5: make sure to CHECK under misc: "no final verification" AND "reset customization"
6: hit Flash button, and wait to prompted to connect phone
7: press and hold Vol- while connect phone to PC
Then the flash process should be starting, and finishing fine. This steps restored my bricked Tipo back to life. Just in case, re-root, and install CWM.
Warning: first boot take some times, be patient! Make sure to do another reboot after first boot up.
Hope it's help.
Click to expand...
Click to collapse
I am having the same issue. Mine is unlocked Bootloader. My TIPO is stuck in JB Mini Project boot animation (Circle with number '10'). I missed to flash boot.img of the kernel before flashing JBMP5 ROM. And now it's stuck.. Cannot enter CWM too.. Phone will not power off too.. Need to take battery out.. When I try to flash laptop says ' Device is not recognized or malfunctioned'
Please help
Thanks,
Asish
Asish said:
I am having the same issue. Mine is unlocked Bootloader. My TIPO is stuck in JB Mini Project boot animation (Circle with number '10'). I missed to flash boot.img of the kernel before flashing JBMP5 ROM. And now it's stuck.. Cannot enter CWM too.. Phone will not power off too.. Need to take battery out.. When I try to flash laptop says ' Device is not recognized or malfunctioned'
Please help
Thanks,
Asish
Click to expand...
Click to collapse
Try another USB cable/port. Sometimes this can cause problems, like Yours... If not use, try another PC. And if possible, use Windows 7.
It Worked!
DSanya said:
Try another USB cable/port. Sometimes this can cause problems, like Yours... If not use, try another PC. And if possible, use Windows 7.
Click to expand...
Click to collapse
Thanks DSanya.. I used Windows 7 and it worked like a charm Tipo was detected and I was able to flash again.. Phone is working fine now. Thanks again.. Appreciate it Cheers!
but it ask to enable usb debugging unfortunately in my phone it was disabled
Hi, I need help. I flashed the DoomsDayRom on my Xperia J ST26i. I followed all the steps and it went well until I wanted to flash a new rom. I found out that I could not access CWM on my phone even after doing the Vol. up button when there's the purple light. In fact, there was no purple light! There was only a blue light before the phone booted up. After that, I deleted the .zip file from my SD card and tried again. It was the same. Except this time, the error message "Unfortunately, the process android.process.acore has stopped.". That popped up every time I closed it and I couldn't do a thing. Please help me!:crying:
I downloaded the rom from here: http://forum.xda-developers.com/xperia-j-e/development/doomsday-rom-jlo-stock-based-t2636164
Try installing CWM from PC again.
If you still can't go to it, you may also try some xposed module (I am sorry, I forgot the name) which gives you options to reboot (even to recovery) when you try to turn off your phone by pressing and holding power button.
If that still doesn't work, you gotta flash your phone bro.
Thanks, but...
maxzeroedge said:
Try installing CWM from PC again.
If you still can't go to it, you may also try some xposed module (I am sorry, I forgot the name) which gives you options to reboot (even to recovery) when you try to turn off your phone by pressing and holding power button.
If that still doesn't work, you gotta flash your phone bro.
Click to expand...
Click to collapse
Thanks, but I've tried installing CWM again, but to no avail. I've also downloaded ROMmanager and tried to reboot into recovery, but the phone just hung. And what do u mean by flashing my phone?
Shuame
Death1792 said:
Thanks, but I've tried installing CWM again, but to no avail. I've also downloaded ROMmanager and tried to reboot into recovery, but the phone just hung. And what do u mean by flashing my phone?
Click to expand...
Click to collapse
Im using Shuame to re-unlock my bootloader and I will then root it...
By Flashing your phone, I mean using Flashtool which uses ftf files to install stock ROM into the phone. Its similar to Sony Update Service or PC Companion repair method, but doesn't require you to download firmware each time you flash.
P.S. Press Post Reply instead of Reply to avoid quoting yourself
Hello,
By flashing thunderzap kernal(Stable version) on my Xperia L, I installed the latest version of Cyanogemode 11(toashan) and there by the firmware was running butter smooth without any problem, now I tried to revert the firmware with stock Rom and I understood that the best way to install stock rom is to flash it via flashtool.The problem what I am facing is after entering in flash mode, the flashtool widget gets stuck at "flashing loader".the percent is stuck at 0%.The confusion comes into play as the phone never shows signs that it is in flash mode.i tried flashing another kernal still the same old problem.
Thanks
Hazil
Sent from my C2104 using XDA Free mobile app
hazil33 said:
Hello,
By flashing thunderzap kernal(Stable version) on my Xperia L, I installed the latest version of Cyanogemode 11(toashan) and there by the firmware was running butter smooth without any problem, now I tried to revert the firmware with stock Rom and I understood that the best way to install stock rom is to flash it via flashtool.The problem what I am facing is after entering in flash mode, the flashtool widget gets stuck at "flashing loader".the percent is stuck at 0%.The confusion comes into play as the phone never shows signs that it is in flash mode.i tried flashing another kernal still the same old problem.
Thanks
Hazil
Sent from my C2104 using XDA Free mobile app
Click to expand...
Click to collapse
Flashing a custom kernel has nothing to do with a stock ftf.
Can you tell the steps that you're following to flash stock?
Reply
abhi007.john said:
Flashing a custom kernel has nothing to do with a stock ftf.
Can you tell the steps that you're following to flash stock?
Click to expand...
Click to collapse
1. Turn off the phone and let it rest for 30 sec and did the below tasks.
2.Copied the stock ftf, C2104_15.3.A.1.17_Generic into the firmware folder of flashtool,clicked the flash mode button in flashtool and waited for the prompt to plug in my phone holding the back button connecting the usb cable.
3.Now i saw a pop up in my pc(windows 7) saying that the device is connected in flash mode.
4.Now the flashtool prompt goes when i connected the device, and it gets stuck at the notification saying "flashing loader" and its at 0%.
This the issue which i am facing right now. I cant flash stock rom and get back to 4.2 :'(
hazil33 said:
1. Turn off the phone and let it rest for 30 sec and did the below tasks.
2.Copied the stock ftf, C2104_15.3.A.1.17_Generic into the firmware folder of flashtool,clicked the flash mode button in flashtool and waited for the prompt to plug in my phone holding the back button connecting the usb cable.
3.Now i saw a pop up in my pc(windows 7) saying that the device is connected in flash mode.
4.Now the flashtool prompt goes when i connected the device, and it gets stuck at the notification saying "flashing loader" and its at 0%.
This the issue which i am facing right now. I cant flash stock rom and get back to 4.2 :'(
Click to expand...
Click to collapse
How could you hold the 'back' button???
there's no such button as far as I know.
Anyways since you're able to connect in flashmode I assume that you're talking about the volume down button. Try changing the firmware(ftf). Instead of generic, try any other version. And run flashtool as administrator.
Best of luck
Hit thanks if it helped
Reply
abhi007.john said:
How could you hold the 'back' button???
there's no such button as far as I know.
Anyways since you're able to connect in flashmode I assume that you're talking about the volume down button. Try changing the firmware(ftf). Instead of generic, try any other version. And run flashtool as administrator.
Best of luck
Hit thanks if it helped
Click to expand...
Click to collapse
Sorry bro, its the vol down button which i am talking about
Reply
abhi007.john said:
How could you hold the 'back' button???
there's no such button as far as I know.
Anyways since you're able to connect in flashmode I assume that you're talking about the volume down button. Try changing the firmware(ftf). Instead of generic, try any other version. And run flashtool as administrator.
Best of luck
Hit thanks if it helped
Click to expand...
Click to collapse
Hello,
I tried that with another stock ftf file and still things aren't working out :'(
hazil33 said:
Hello,
I tried that with another stock ftf file and still things aren't working out :'(
Click to expand...
Click to collapse
download latest flashtool this one is old
Flashing_Expert said:
download latest flashtool this one is old
Click to expand...
Click to collapse
Issue fixed after updating flashtool
Hi guys I rooted my Z3 and installed TWRP so i could install a custom rom. So I downloaded the ROM, booted to TWRP, wiped everything, then installed the ROM. It said everything was successful so I rebooted my phone. Now there is a black screen. When I hold the power button, the phone vibrates for a second but nothing happens. When I plug my phone in, there is a red flashing light. What do I do?? Please help me.
shspeed said:
Hi guys I rooted my Z3 and installed TWRP so i could install a custom rom. So I downloaded the ROM, booted to TWRP, wiped everything, then installed the ROM. It said everything was successful so I rebooted my phone. Now there is a black screen. When I hold the power button, the phone vibrates for a second but nothing happens. When I plug my phone in, there is a red flashing light. What do I do?? Please help me.
Click to expand...
Click to collapse
which custom rom? And have you unlocked the bootloader?
gregbradley said:
which custom rom? And have you unlocked the bootloader?
Click to expand...
Click to collapse
It was the Validus ROM. I didnt unlock the bootloader. I feel like an idiot right now. Is there any way to fix this?
shspeed said:
It was the Validus ROM. I didnt unlock the bootloader. I feel like an idiot right now. Is there any way to fix this?
Click to expand...
Click to collapse
That has a custom kernel so you need to unlock the bootloader to flash it.
To repair it you can restore the backup you must have taken in recovery before flashing the rom
or
Flash a stock FTF in flashtool from flashtool.net
or
Force a software repair using PCCompanion.
gregbradley said:
That has a custom kernel so you need to unlock the bootloader to flash it.
To repair it you can restore the backup you must have taken in recovery before flashing the rom
or
Flash a stock FTF in flashtool from flashtool.net
or
Force a software repair using PCCompanion.
Click to expand...
Click to collapse
Ok thanks. How would i be able to restore the backup if i cant get into recovery?
shspeed said:
Ok thanks. How would i be able to restore the backup if i cant get into recovery?
Click to expand...
Click to collapse
The custom kernel should have recovery in it (Probably) so you can try entering by pressing the volume up or down button when you reboot the phone.
EDIT, my mistake, the kernel is not booting.
Flash a stock FTF ending in .93, root, install recovery and restore the backup
or
Force a software repair using PCCompanion, downgrade, root, install recovery, restore backup
gregbradley said:
The custom kernel should have recovery in it (Probably) so you can try entering by pressing the volume up or down button when you reboot the phone.
EDIT, my mistake, the kernel is not booting.
Flash a stock FTF ending in .93, root, install recovery and restore the backup
or
Force a software repair using PCCompanion, downgrade, root, install recovery, restore backup
Click to expand...
Click to collapse
OK im in flashtool but when i plug my phone in to flash, it asks for drivers, but I have all the drivers installed. What should I do? http://gyazo.com/29bbe3a0b82d333acc8efe03be4275c5
goto C:\flashtool\drivers
run drivers.exe
choose Z3, fastboot and flashmode drivers
restart PC and try again.
Also, it would help if you show the whole log from flashtool.....
gregbradley said:
goto C:\flashtool\drivers
run drivers.exe
choose Z3, fastboot and flashmode drivers
restart PC and try again.
Also, it would help if you show the whole log from flashtool.....
Click to expand...
Click to collapse
OK, so I updated flashtool, got all the drivers, then restarted my pc and flashed and it worked. Now I will re root and try again. Thank you so much for helping me out with this. If there is anything I can do to for you, let me know. I appreciate the time that you set out from your day to help.
i rooted my xperia L times ago. now I wanna install cyanogenmod. i can't load the recovery menu with vol- and power button, so used quikboot 4.1. And now there isn't any option to update from internal or external storage. it just recommend to update via ADM, and I've trobble using the ADM.
my PC first recognized the ADM through usb, but now it dos'nt recognize it. like no thing is connected in bootloader mode. and I dont have any SDK or ADM program running in my win7.
I dont know were to download it!!!! I just found a crashed link in xda!
pleeeeeeease help me. I realy need the cm, my xperia is not in good mood:crying:
PL.biologist said:
i rooted my xperia L times ago. now I wanna install cyanogenmod. i can't load the recovery menu with vol- and power button, so used quikboot 4.1. And now there isn't any option to update from internal or external storage. it just recommend to update via ADM, and I've trobble using the ADM.
my PC first recognized the ADM through usb, but now it dos'nt recognize it. like no thing is connected in bootloader mode. and I dont have any SDK or ADM program running in my win7.
I dont know were to download it!!!! I just found a crashed link in xda!
pleeeeeeease help me. I realy need the cm, my xperia is not in good mood:crying:
Click to expand...
Click to collapse
The recovery you're booting to is not a custom recovery ,anyway I'll giude to installing I'll give some useful links.
First if all you need to unlock your bootloader go here
http://forum.xda-developers.com/xperia-l/general/xperia-l-how-to-flash-tool-unlocking-t2337955
You may run in a bootloop (the phone stuck at bootanimation)
Just flash the stock ftf via flashtool .
Now go here and take the first method , it will guide how to install CM12
http://forum.xda-developers.com/showpost.php?p=63769485&postcount=2
Remember that the first may take sometime so don't pullout the batterybattery.
Good luck:highfive:
n78 shadow said:
The recovery you're booting to is not a custom recovery ,anyway I'll giude to installing I'll give some useful links.
First if all you need to unlock your bootloader go here
http://forum.xda-developers.com/xperia-l/general/xperia-l-how-to-flash-tool-unlocking-t2337955
You may run in a bootloop (the phone stuck at bootanimation)
Just flash the stock ftf via flashtool .
Now go here and take the first method , it will guide how to install CM12
http://forum.xda-developers.com/showpost.php?p=63769485&postcount=2
Remember that the first may take sometime so don't pullout the batterybattery.
Good luck:highfive:
Click to expand...
Click to collapse
thank for solutions. but before your reply, I used the recovery installer. it bring a good recovery menu in my xperia L. finally i updated to cm12.1, after successful update, it goes to reboot. but it did'nt turn on! unfortunately, no signal from my xperia L. it goes to fastboot mode and flash mode. but flashtool dont flash the phone using fastmode and boot.img from cm12.1 files!
what should i do, with this off phone, red led blinking!
PL.biologist said:
thank for solutions. but before your reply, I used the recovery installer. it bring a good recovery menu in my xperia L. finally i updated to cm12.1, after successful update, it goes to reboot. but it did'nt turn on! unfortunately, no signal from my xperia L. it goes to fastboot mode and flash mode. but flashtool dont flash the phone using fastmode and boot.img from cm12.1 files!
what should i do, with this off phone, red led blinking!
Click to expand...
Click to collapse
Are you sure that your bootloader is unlocked?
Anyway try to flash the stock ftf ,download the suitable one here
http://forum.xda-developers.com/xperia-l/general/sony-xperia-l-flashable-ftfs-locked-t2560642