[Q] Help please - Micromax A110

I flashed MIUI V5 4.2.2, after installing a new theme system UI stopped working .... it is annoying me .... any solution ????? i deleted the theme and also reflashed the rom but same problem ..... help meeeeeee

Solomon258 said:
I flashed MIUI V5 4.2.2, after installing a new theme system UI stopped working .... it is annoying me .... any solution ????? i deleted the theme and also reflashed the rom but same problem ..... help meeeeeee
Click to expand...
Click to collapse
reboot into recovery
wipe data, cache and dalvik cache
after that flashing the rom may solve the issue

Re install CWM recovery itself.
Solomon258 said:
I flashed MIUI V5 4.2.2, after installing a new theme system UI stopped working .... it is annoying me .... any solution ????? i deleted the theme and also reflashed the rom but same problem ..... help meeeeeee
Click to expand...
Click to collapse
Re install CWM recovery itself. and then try flashing the ROM

Related

Force close with brainmaster's MIUI 1.9.30.2

firstful the ROM is great but I having this problem after flashing the rom
Force close in everything and I wanna enjoy the rom
my dvice is Nexus s 9023 I hope you can help me ​
wesam32003 said:
firstful the ROM is great but I having this problem after flashing the rom
Force close in everything and I wanna enjoy the rom
my dvice is Nexus s 9023 I hope you can help me ​
Click to expand...
Click to collapse
you probably didn't do a complete wipe before flashing
No but I did format system , data , boot , from the recovery mode I think it's the same
Or not plz help me
Try one of the alternate kernels on his second post in his thread, and do a cache and dalvic wipe
Sent from the future to put right what once went wrong.

G3MOD Kernel for JB/ICS

Hi,
I have taken the code of G3MOD code and modded it for JB.
Also I have included the Bluetooth fix that I have done for ICS. Yeah the same fix is also available in JB.
Use this kernel with ICS & JB as the bluetooth fix is applied only to these two versions.
Try it out and let me know the comments.
Download Here
Thanks to all G3 developers.
Special Thanks to g3mod team, marcellusbe, hillbeast, cdesai.
If I forget to thank anyone it's not intended, PM me. I will thank you.
Note: I am not responsible for any damage caused to your phone (softbrick or hardbrick).
Thanks mate , Hope to see more development from your side as well ...to make G3 the best ever phone
Can you make a .tar version please? I can't flash it through CWM.... I flashed JB then without rebooting flashed this but it still didn't work... Same with gapps, they don't install for me...
I also can't flash this kernel either as it still says im on [email protected] #cm7_kernel_oc_1.8
Are we able to access CWM then?
Hi, for me is it working I wiped cache and dalwik cache. May be it help...
Sorry for my bad english
BeriCud said:
Hi, for me is it working I wiped cache and dalwik cache. May be it help...
Sorry for my bad english
Click to expand...
Click to collapse
Ok How
1 . instal rom tru CWm then wiped cache and dalwik cache and after that instal g3mod ????
ilievski.ace said:
Ok How
1 . instal rom tru CWm then wiped cache and dalwik cache and after that instal g3mod ????
Click to expand...
Click to collapse
When you install the ROM you should wipe the data as well but when installing the kernel you should wipe cache and dalvik cache.
Click thanks if I helped.
Thank you very much....
A small query....
If I install the kernel immediately after applying JB update then will I be able to access cwm the next time??
Thanks
kernel "bluetooth???"
hello
i have installed this kernel for cm7-8.3, and wipe dalvik cahche but i probed bluetooth whit another phone and got message "couldn't connect"
the copulation is ok, but not connect!!!:crying:
earlier i was foryo, and bluetooth is working perfect!
any idea?
I have not tried with CM7. Use this kernel with ICS / JB as the bluetooth fix is applied only to these two versions. Will try with CM7 and update the kernel later.
zsolt64 said:
hello
i have installed this kernel for cm7-8.3, and wipe dalvik cahche but i probed bluetooth whit another phone and got message "couldn't connect"
the copulation is ok, but not connect!!!:crying:
earlier i was foryo, and bluetooth is working perfect!
any idea?
Click to expand...
Click to collapse
pmanian said:
I have not tried with CM7. Use this kernel with ICS / JB as the bluetooth fix is applied only to these two versions. Will try with CM7 and update the kernel later.
Click to expand...
Click to collapse
First i do is
1. Install jb-pre relice and claer data , davik i cashe ...
2 . instal G3 mod kernel JB and clear cashe and davik and reboot
AND is bootingh infinitive ...... stack on boot animation ANDROID ......
HElp
@pmanian
Can you make UMS working on ICS/JB with g3mod kernel?
To all who managed to get it working: Do data2sd and CWM work? These are the key features I'm missing right now
Thanks a lot!!
Sent from my GT-I5801 using xda app-developers app
you are rocking sir !! :good: this kernel is a real good !! thanks a ton for it.
Is JB available for G3 ? i guess Marcellube is working on it and haven't released JB yet.
pathfinderhd said:
you are rocking sir !! :good: this kernel is a real good !! thanks a ton for it.
Is JB available for G3 ? i guess Marcellube is working on it and haven't released JB yet.
Click to expand...
Click to collapse
Search the JB thread in the development section. He released a build but it is old and has quite a few bugs in it which he has fixed.
I reflashed JB, then g3mod, wiped data, cache and dalvik cache. Neither CWM nor data2sd are working, but the bootscreen changed, and I don't get stuck. Can anyone help me?
ilievski.ace said:
First i do is
1. Install jb-pre relice and claer data , davik i cashe ...
2 . instal G3 mod kernel JB and clear cashe and davik and reboot
AND is bootingh infinitive ...... stack on boot animation ANDROID ......
HElp
Click to expand...
Click to collapse
I am raplaying to mi self OK need HELP
Some body to make the G3Mod karnel to Odin and thel me what or how to clear Davik or to Clear Cashe .... ??
When instaling G3Mod In JB i have bootloop .....
Thanks
ilievski.ace said:
I am raplaying to mi self OK need HELP
Some body to make the G3Mod karnel to Odin and thel me what or how to clear Davik or to Clear Cashe .... ??
When instaling G3Mod In JB i have bootloop .....
Thanks
Click to expand...
Click to collapse
take any tar of any rom.......remove all the files in it and place the zImage file in the provided zip into the tar file.(With the help of TOTAL COMMANDER)
process:
Install the ROM through CWM...
then go to download mode and then flash the kernel through ODIN
reboot in to recovery and clear cache & dalvik-Cache.
reboot & enjoy.

problem installing XZX 2 rom for xperia s(HELP)

anyone can help me please .. i really like to try XZXperience 2 custom rom but when i flash it and reboot it jus freeze at blank screen. i try flash other custom rom is working fine. please help .. i using xperia S .
stevenliaw said:
anyone can help me please .. i really like to try XZXperience 2 custom rom but when i flash it and reboot it jus freeze at blank screen. i try flash other custom rom is working fine. please help .. i using xperia S .
Click to expand...
Click to collapse
If you can boot into CWM then try reinstalling the ROM. Before installing wipe dalvic cache, format system, data and cache under "mounts and storage menu" then reinstall the ROM. The post also says that you need to be on "official 6.1.A.2.50" before installing the custom ROM.

[Q] [HELP] Stuck at HTC Logo and Recovery

So, I haven't been using my pico recently..used it about 6 months ago and it has been unused ever since..
Today, I finally picked it up and tried to install MIUI V4. I updated TWRP to 2.7 and it was updated.. Deleted the previous rom and installed the MIUI zip.. When I restarted even the MIUI bootanimation did not show up, only the HTC Logo showed up, and the phone rebooted into recovery. .
So, is it bricked ? I tried installing CM9 but same problem..Any help will be appreciated
TAOprajjwal said:
So, I haven't been using my pico recently..used it about 6 months ago and it has been unused ever since..
Today, I finally picked it up and tried to install MIUI V4. I updated TWRP to 2.7 and it was updated.. Deleted the previous rom and installed the MIUI zip.. When I restarted even the MIUI bootanimation did not show up, only the HTC Logo showed up, and the phone rebooted into recovery. .
So, is it bricked ? I tried installing CM9 but same problem..Any help will be appreciated
Click to expand...
Click to collapse
did you 'Make a clean install' , when you flash different rom you have to Clean old one
In TWRP 2.7
Go to WIPE > Advanced Wipe > select :dalvik, cache , data ,system > swipe to clean >>>Than flash ur rom bro
XenoMorphv2 said:
did you 'Make a clean install' , when you flash different rom you have to Clean old one
In TWRP 2.7
Go to WIPE > Advanced Wipe > select :dalvik, cache , data ,system > swipe to clean >>>Than flash ur rom bro
Click to expand...
Click to collapse
Yup wiped everything including system and sd-ext partiton
TAOprajjwal said:
Yup wiped everything including system and sd-ext partiton
Click to expand...
Click to collapse
i dont know bro maybe you need to change recovery ? also can try nand recoveryies... again i dont know much but you can try to 'fastboot flash boot boot.img' method...
our forum slowly dies
TAOprajjwal said:
So, I haven't been using my pico recently..used it about 6 months ago and it has been unused ever since..
Today, I finally picked it up and tried to install MIUI V4. I updated TWRP to 2.7 and it was updated.. Deleted the previous rom and installed the MIUI zip.. When I restarted even the MIUI bootanimation did not show up, only the HTC Logo showed up, and the phone rebooted into recovery. .
So, is it bricked ? I tried installing CM9 but same problem..Any help will be appreciated
Click to expand...
Click to collapse
i think may b its a issue with twrp version... try twrp v2.6 or lower... i think it will work for sure...

Clean Kat v4 for Huawei Honor Holly....!

;Its my first thread on xda
ROM Name- CleanKat V4.0
Device- Huawei Honor Holly (Ported it from Walton Primo GF2)
ROM Developer- Umang Leekha
ROM Porter- Waseem Maya
For Internal Storage Bug Fixing - Muhammad Waqas Hameed
If I forgot someone then tell me....!
Features
1. Based on AOSP KITKAT
2.Better battery life than other KK
ROMs, stock kernel
3.Added data traffic monitor in settings,
you can toggle it
4.Added 13 new battery icon styles in
settings, ported from carbon rom
5.Beautiful Cleankat lockscreen,
screenshot attached
6.Beautiful Cleankat bootanimation and
bootlogo
7.Cleankat music player, advanced
calculator and browser
And....!
And.........!
And...............!
Many More.............!
Now Come to the main thread...!
Hello Guys....!
Now presenting You CLEAN KAT V4 for HUAWEI HONOR HOLLY
PURE AOSP 4.4 (Kitkat)
Ported by Waseem Maya (ME)
Instructions to Install:
Go Into Philz Touch Recovery
Select Wipa & Data
Select Clean To Install a New Rom
Select Install Zip from SD Card
Select Clean Kat V4
Install it....
Done
After Install
Clear Cache & Dalvik Cache
Bugs:
It has no bug...!
Engineering Mode:
MTK Enginnering Mode APK Iin Attachment....!
you can increase sound level of your phone in Engineering Mode...!
If you found any bugs please inform me.....!
Download Link:
http://d-h.st/1w68​
Please add this rom on Huawei Honor Holly main page
Great work! Can you list the features of this ROM?
fiorezy said:
Great work! Can you list the features of this ROM?
Click to expand...
Click to collapse
Ok wait
Sent from my Hol-U19 using Tapatalk
thanks for your accomplishment
does it support Arabic language completely
does it include GAPPS or i need to flash them seperately
can i install it thru twrp recovery ? if yes how ?
best regards
I dont know if it supports Arabic or not and you dont need flash gapps its already included yes you can flash using twrp band do wipe data factory reset and install after install clear cache and dalvik cache.... Now reboot...! Done
Sent from my Hol-U19 using Tapatalk
waseemmayaa said:
I dont know if it supports Arabic or not and you dont need flash gapps its already included yes you can flash using twrp band do wipe data factory reset and install after install clear cache and dalvik cache.... Now reboot...! Done
Sent from my Hol-U19 using Tapatalk
Click to expand...
Click to collapse
how can i check if it support Arabic before flashing it ? any idea
musafercom said:
how can i check if it support Arabic before flashing it ? any idea
Click to expand...
Click to collapse
I'm gonna test it then I will tell you
fiorezy said:
I'm gonna test it then I will tell you
Click to expand...
Click to collapse
Bootloop
EDIT: I fixed it after changing boot.img with stock.
Great ROM and very smooth, btw it SUPPORTS ARABIC!
fiorezy said:
Bootloop
EDIT: I fixed it after changing boot.img with stock.
Great ROM and very smooth, btw it SUPPORTS ARABIC!
Click to expand...
Click to collapse
CAN YOU EXPLAIN MORE.
JUST TO MAKE SURE DOES IT SUPPORT ARABIC FULLY.
WHAT IS btw ?
I AM ON STOCK ROM
MY DEVICE IS ROOTED AND ON TWRP RECOVERY WHAT SHOULD I DO IN STEPS TO FLASH THIS ROM WITHOUT GETTING STOCK IN A BOOT LOOP IF YOU GREATLY RECOMMEND THE ROM AND ITS STABLE WITHOUT BUGS AND HOW TO GO BACK TO STOCK ROM IF I DO NOT LIKE OR IF SOMETHING GO WRONG.
THANKS & BEST REGARDS
musafercom said:
CAN YOU EXPLAIN MORE.
JUST TO MAKE SURE DOES IT SUPPORT ARABIC FULLY.
WHAT IS btw ?
I AM ON STOCK ROM
MY DEVICE IS ROOTED AND ON TWRP RECOVERY WHAT SHOULD I DO IN STEPS TO FLASH THIS ROM WITHOUT GETTING STOCK IN A BOOT LOOP IF YOU GREATLY RECOMMEND THE ROM AND ITS STABLE WITHOUT BUGS AND HOW TO GO BACK TO STOCK ROM IF I DO NOT LIKE OR IF SOMETHING GO WRONG.
THANKS & BEST REGARDS
Click to expand...
Click to collapse
btw= by the way
I already tried this ROM and i'm sure that it fully supports Arabic, It was very smooth and handy, I used it for short minutes then I went back to MIUI because I didn't like the full grey design.
To install it, first at all, copy the zip file on your SD card, Boot into recovery mod, backup you current ROM to SD card in case something wrong happened. After that, wipe data and cache then flash Clean Kat, finally wipe dalvik cache and tap reboot system.
In case you got bootloop or you didn't like Clean Kat, just go back to twrp and restore your backup.
fiorezy said:
btw= by the way
i already tried this rom and i'm sure that it fully supports arabic, it was very smooth and handy, i used it for short minutes then i went back to miui because i didn't like the full grey design.
To install it, first at all, copy the zip file on your sd card, boot into recovery mod, backup you current rom to sd card in case something wrong happened. After that, wipe data and cache then flash clean kat, finally wipe dalvik cache and tap reboot system.
In case you got bootloop or you didn't like clean kat, just go back to twrp and restore your backup.
Click to expand...
Click to collapse
do i need to fatctory reset ?
Does that mean i do not need stock recovery to do that.
How to go to twrp recovery if i got a bootloob
musafercom said:
do i need to fatctory reset ?
Does that mean i do not need stock recovery to do that.
How to go to twrp recovery if i got a bootloob
Click to expand...
Click to collapse
Don't do factory reset, just install twrp first
Go to this thread and you will find many useful things
fiorezy said:
don't do factory reset, just install twrp first
go to this thread and you will find many useful things
Click to expand...
Click to collapse
i have twrp already
thanks
How was the rom ( CleanKat ) now I am porting Resurrection Remix 5.1.1 for HHH but there are bugs in it....!
Sent from my Hol-U19 using XDA Free mobile app
waseemmayaa said:
How was the rom ( CleanKat ) now I am porting Resurrection Remix 5.1.1 for HHH but there are bugs in it....!
Sent from my Hol-U19 using XDA Free mobile app
Click to expand...
Click to collapse
Clean Kat was very smooth, no bugs so far, didn't use it for much time, but I think everything is working fine, besides a liitle bug when scrolling through Download files, and there is no option to disable soft keys.
You can disable it by editing build.prop
Sent from my Hol-U19 using XDA Free mobile app
Help me pls. My phone is on bootloop after flashing cleankat rom. How can i replace the boot.img of cleankat rom to stock boot.img?i have no.pc,only phone. I tried moving stock boot.img to cleankat rom using xplore but it corrypt the zip file. Pls help
yuansmart said:
Help me pls. My phone is on bootloop after flashing cleankat rom. How can i replace the boot.img of cleankat rom to stock boot.img?i have no.pc,only phone. I tried moving stock boot.img to cleankat rom using xplore but it corrypt the zip file. Pls help
Click to expand...
Click to collapse
Give me your stock boot.img, I will try to upload for you the whole ROM tomorrow
How can i fimd my stock boot.img?pls

Categories

Resources