Related
Well I finally managed to Hard Brick my A110 a few days back. I was thinking that everything was lost and my A110 was as good as a brick! But I struggled with it for two days and finally managed to bring it back to life! This is how I hard bricked it, but resurrected it too....
Hard brick:
The hard brick happens when you flash a non A110 stock ROM through SP flash. This happens when you get overconfident during ROM development experiments and forget the basic fact that flashing the "pre-loader" accidentally of any other ROM( (even if it is of MT6577) that is different from A110 leads to the phone going dead. The charge LED dies, and the phone is totally in alien land when the PC sees it through the USB cable You cannot flash anything through the SP flash any more. The phone will not power on or boot. Welcome to the land of bricked phones!
Resurrection:
1) First perform an uninstall of the MMX/Mobistel drivers you already have on
your P.C. Install the drivers again.
2) Take a piece of insulated wire (Around 3 cms long) and solder a 10K resistor
to one end. To the other end solder a pin to the pin head so that the tip is
free.
3) Remove your phone battery and keep the phone ready.
4) On the PC/Laptop, start SP flash tool and select the right scatter from the factory stock A110 ROM. un-tick all except the first five (Preloader, DSP_BL, MBR, EBR1, UBOOT) + CWM recovery (You should have replaced default recovery with CWM recovery in the ROM folder). Click "Firmware-upgrade, Download.
5) With battery taken off from your phone connect it to the PC/Lap using the USB cable.
6) Now touch the resistor end to the USB Cable outer part (GND) visible at the point of USB connector connected to the phone.
7) Touch the other part (pin end) to all visible copper terminals one by one.
8) Now without removing the cable, place the battery back.
9) Now keep your fingers crossed. If you have luck, you will see the red, blue, green and finally yellow lines on the SP tool window. You are done!!!
10) If your battery was having good charge when you were bricked, you can now power on to recovery mode and flash your CWM saved ROM or any other ROM.
11) If your battery was low, when you were bricked, leave it to charge for an hour before attempting to flash the entire stock ROM through SP flash or CWM.
Cheers!!!:victory:
Its better u make a video and attached it below. its really helpful. thanxx a lot mate for creating this solution :thumbsup:
i second that suggestion! a video or an orderly series of pics........
skdmech94 said:
Its better u make a video and attach.........
Click to expand...
Click to collapse
wow maan u really are awesome i never had myself in d scenario but now i know that theres always a way thanks to you hats off to u pal
Yap bro u r right....u have to post a video guide......
colors can.....canvas 2
At least a series of pictures are most for such guide.
Great tutorial (please make video or screens)
Will help so many a110 users
Whose devices are in verge of death
From horrible MMX service center guys
Sent from my Micromax A110 using xda premium
Great article!! Video would be extremely helpful!
Sent from my GT-I9300 using xda app-developers app
Hard brick occurs when we flash preloader of different incompatible fone ryt...and hence fone wont detect on spflash tool..
What if we install the preloader drivers of that incompatible device; can we get the fone to detect in spflashtools ? If it wrks, then we can flash back the A110 preloader files ryt ?
Some one with a hardbricked device ,pls try it out if possible, before doing the hardware method suggested by OP
Sent from my Micromax A110
pcoruganti said:
Great article!! Video would be extremely helpful!
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
Will post some snaps
Hi,
Thanks for this wonderful tutorial, Now i am not worried about my phone being bricked when i try new things in my mobile. thanks buddy.
where i can get CWM recovery?
Where i can get that CWM recovery?
I followed all these steps i couldnt do anymore, what i should i do next? Plz help
I followed all these steps i couldnt do anymore, what i should i do next? Plz help
pradipsoman said:
Well I finally managed to Hard Brick my A110 a few days back. I was thinking that everything was lost and my A110 was as good as a brick! But I struggled with it for two days and finally managed to bring it back to life! This is how I hard bricked it, but resurrected it too....
Hard brick:
The hard brick happens when you flash a non A110 stock ROM through SP flash. This happens when you get overconfident during ROM development experiments and forget the basic fact that flashing the "pre-loader" accidentally of any other ROM( (even if it is of MT6577) that is different from A110 leads to the phone going dead. The charge LED dies, and the phone is totally in alien land when the PC sees it through the USB cable You cannot flash anything through the SP flash any more. The phone will not power on or boot. Welcome to the land of bricked phones!
Resurrection:
1) First perform an uninstall of the MMX/Mobistel drivers you already have on
your P.C. Install the drivers again.
2) Take a piece of insulated wire (Around 3 cms long) and solder a 10K resistor
to one end. To the other end solder a pin to the pin head so that the tip is
free.
3) Remove your phone battery and keep the phone ready.
4) On the PC/Laptop, start SP flash tool and select the right scatter from the factory stock A110 ROM. un-tick all except the first five (Preloader, DSP_BL, MBR, EBR1, UBOOT) + CWM recovery (You should have replaced default recovery with CWM recovery in the ROM folder). Click "Firmware-upgrade, Download.
5) With battery taken off from your phone connect it to the PC/Lap using the USB cable.
6) Now touch the resistor end to the USB Cable outer part (GND) visible at the point of USB connector connected to the phone.
7) Touch the other part (pin end) to all visible copper terminals one by one.
8) Now without removing the cable, place the battery back.
9) Now keep your fingers crossed. If you have luck, you will see the red, blue, green and finally yellow lines on the SP tool window. You are done!!!
10) If your battery was having good charge when you were bricked, you can now power on to recovery mode and flash your CWM saved ROM or any other ROM.
11) If your battery was low, when you were bricked, leave it to charge for an hour before attempting to flash the entire stock ROM through SP flash or CWM.
Cheers!!!:victory:
Click to expand...
Click to collapse
pradipsoman said:
Well I finally managed to Hard Brick my A110 a few days back. I was thinking that everything was lost and my A110 was as good as a brick! But I struggled with it for two days and finally managed to bring it back to life! This is how I hard bricked it, but resurrected it too....
Hard brick:
The hard brick happens when you flash a non A110 stock ROM through SP flash. This happens when you get overconfident during ROM development experiments and forget the basic fact that flashing the "pre-loader" accidentally of any other ROM( (even if it is of MT6577) that is different from A110 leads to the phone going dead. The charge LED dies, and the phone is totally in alien land when the PC sees it through the USB cable You cannot flash anything through the SP flash any more. The phone will not power on or boot. Welcome to the land of bricked phones!
Resurrection:
1) First perform an uninstall of the MMX/Mobistel drivers you already have on
your P.C. Install the drivers again.
2) Take a piece of insulated wire (Around 3 cms long) and solder a 10K resistor
to one end. To the other end solder a pin to the pin head so that the tip is
free.
3) Remove your phone battery and keep the phone ready.
4) On the PC/Laptop, start SP flash tool and select the right scatter from the factory stock A110 ROM. un-tick all except the first five (Preloader, DSP_BL, MBR, EBR1, UBOOT) + CWM recovery (You should have replaced default recovery with CWM recovery in the ROM folder). Click "Firmware-upgrade, Download.
5) With battery taken off from your phone connect it to the PC/Lap using the USB cable.
6) Now touch the resistor end to the USB Cable outer part (GND) visible at the point of USB connector connected to the phone.
7) Touch the other part (pin end) to all visible copper terminals one by one.
8) Now without removing the cable, place the battery back.
9) Now keep your fingers crossed. If you have luck, you will see the red, blue, green and finally yellow lines on the SP tool window. You are done!!!
10) If your battery was having good charge when you were bricked, you can now power on to recovery mode and flash your CWM saved ROM or any other ROM.
11) If your battery was low, when you were bricked, leave it to charge for an hour before attempting to flash the entire stock ROM through SP flash or CWM.
Cheers!!!:victory:
Click to expand...
Click to collapse
if you will make video...then u r awesome awesome awesome
Sent from my Demon A110 using xda app-developers app
drsooraj said:
Hard brick occurs when we flash preloader of different incompatible fone ryt...and hence fone wont detect on spflash tool..
What if we install the preloader drivers of that incompatible device; can we get the fone to detect in spflashtools ? If it wrks, then we can flash back the A110 preloader files ryt ?
Some one with a hardbricked device ,pls try it out if possible, before doing the hardware method suggested by OP
Sent from my Micromax A110
Click to expand...
Click to collapse
What an idea.
The only problem is who's gonna hard brick his phone for this experiment.
Matthew_Farrell said:
What an idea.
The only problem is who's gonna hard brick his phone for this experiment.
Click to expand...
Click to collapse
yea ...thats why i am asking it to the next guy who gets a hardbrick and is just about to follow pradip sir's steps following this thread, to just give a try , before doing it the hardwire method!
Resister method works for almost every phone
It will put the phone in download mode
Even it is not booting or charging
guide can be found on xda
Just search it
Jigs methods works as well
Sent from my Micromax A110 using xda premium
In Step 7 which "visible copper terminals" are meant?
The Phone is connected to PC and the other end of data cable is pluged into phone, so there are no copper pins to touch.
is it possible to do same on mmx a87... m8ne is also hard bricked....
Phoenix said:
Resister method works for almost every phone
It will put the phone in download mode
Even it is not booting or charging
guide can be found on xda
Just search it
Jigs methods works as well
Sent from my Micromax A110 using xda premium
Click to expand...
Click to collapse
after getting into the download mode how can I flash a rom in mmx a87.. plz help.. my fone hard bricked...
Hey guys.. New around the xda forums but not to the Android world.
Coming to the point, Here are the problems i'm facing with my Micromax A110 (Factory version: Andoid Jellybean - 4.1.1)
Everything that i tried so far:
(I have the ADB Interface and the micromax factory drivers in this step)
1. I installed on the Micromax Drivers provided itself by the phone.. the 64bit one as i have Windows Ultimate x64. Now the problem starts when i use the Su Recovery Tool by Bin4ry (or whatever his name is). Everything goes normal..i went by the instructions i.e Usb debug on ---> Media Device. Then on the tool i pressed 1 i.e The normal option and then carry the on screen instructions. It does come to the restore my data part and reboots. Now.. during the reboot, I get a windows update prompt which installs the MT65xx Preloader Drivers. However, the phone does not restart and so as well the drivers as it says device unplugged and then.. poof! Nothing happens.. I have to Remove the battery, restart manually and the program says.. Unable to copy files..Are you root?.. -_- Dafuq?
2. Now i used the famous SP FLASH tool.. but no luck again.. I tried to flash CWM Recovery through it.. but the application has its own problems.. either error 3013 (SOC VERIFICATION FAIL) or again.. the MT65xx driver not found.. AGAIN. -_-" I once also got the 1013 error
I did try disabling the driver enforcement signing but it was of no use (Obviously)
Your help will be appreciated (Thanks option ofcourse). Looking forward to your Reply
-R4vnit
P.S - I dealt with the Mt65xx driver problem, but still.. the Su Bin4ry file cannot flash anything onto the phone (error protocol (status))
ravnit said:
Hey guys.. New around the xda forums but not to the Android world.
Coming to the point, Here are the problems i'm facing with my Micromax A110 (Factory version: Andoid Jellybean - 4.1.1)
Everything that i tried so far:
(I have the ADB Interface and the micromax factory drivers in this step)
1. I installed on the Micromax Drivers provided itself by the phone.. the 64bit one as i have Windows Ultimate x64. Now the problem starts when i use the Su Recovery Tool by Bin4ry (or whatever his name is). Everything goes normal..i went by the instructions i.e Usb debug on ---> Media Device. Then on the tool i pressed 1 i.e The normal option and then carry the on screen instructions. It does come to the restore my data part and reboots. Now.. during the reboot, I get a windows update prompt which installs the MT65xx Preloader Drivers. However, the phone does not restart and so as well the drivers as it says device unplugged and then.. poof! Nothing happens.. I have to Remove the battery, restart manually and the program says.. Unable to copy files..Are you root?.. -_- Dafuq?
2. Now i used the famous SP FLASH tool.. but no luck again.. I tried to flash CWM Recovery through it.. but the application has its own problems.. either error 3013 (SOC VERIFICATION FAIL) or again.. the MT65xx driver not found.. AGAIN. -_-" I once also got the 1013 error
I did try disabling the driver enforcement signing but it was of no use (Obviously)
Your help will be appreciated (Thanks option ofcourse). Looking forward to your Reply
-R4vnit
P.S - I dealt with the Mt65xx driver problem, but still.. the Su Bin4ry file cannot flash anything onto the phone (error protocol (status))
Click to expand...
Click to collapse
Hey I too had the problem previously I have install com drivers problem solved go here www.moulnisky.com. select Micromax /mmxa110/ you can find it there please hit thanks
If it doesn't work there may be problem with ROM which ROM are you trying flashing another ROM
http://forum.xda-developers.com/showthread.php?t=2263511
Try this ROM it is best at least hit thanks it that thread please
Sent from my Micromax A110 using xda premium
nikhilmendu said:
Hey I too had the problem previously I have install com drivers problem solved go here www.moulnisky.com. select Micromax /mmxa110/ you can find it there please hit thanks
If it doesn't work there may be problem with ROM which ROM are you trying flashing another ROM
http://forum.xda-developers.com/showthread.php?t=2263511
Try this ROM it is best at least hit thanks it that thread please
Sent from my Micromax A110 using xda premium
Click to expand...
Click to collapse
I dont mind giving a Thanks but none of the above drivers work and they have a yellow exclamation on them in device manager.. :'(
Basically all the drivers u need are in or phone. Delete all pre loader and com driver using driver management or reinstall using setup.
And I think u know this steps to flash ROM using sp tool.
Alternative
Use mobile uncle to flash recovery.
Sent from my Micromax A110 using xda premium
salil is right..
uninstall previous drivers use Revo unintaller as it removes the traces as well..
Then flash CWM through SPFlash tool!
Well if you aren't rooted you can't use Mobile Uncle Tool!
.salil. said:
Basically all the drivers u need are in or phone. Delete all pre loader and com driver using driver management or reinstall using setup.
And I think u know this steps to flash ROM using sp tool.
Alternative
Use mobile uncle to flash recovery.
Sent from my Micromax A110 using xda premium
Click to expand...
Click to collapse
Thanks for your advice mate.. although Skyrazor is right as root is required for Mobile uncle tools..
Im going to reinstall all drivers and let you know what the outcome is.
Thanks for your time
Hi all
I've managed to create a CWM recovery for the Zen Ultrafone 701HD..... Thought I'd share this too...
For my tutorial on Rooting the same phone see here :-
http://forum.xda-developers.com/showthread.php?t=2283125
See the above link to activate USB debugging and install ADB drivers.....
CREDITS:-
I've Tested the CWMr on my own Phone....It Works..
This was made through the resources already available on various threads in XDA..
All credits to the original developers...
Special thanks to Koush Dutta for his online CWM revovery builder.... works like a charm..
I take DO NOT responsibility for any damages - It worked on my phone, no reason it should
not work on the other 701HDs out there.... Take a backup of all important stuff... Better safe than sorry..
STEP 1 - INSTALL PHONE DRIVERS
Connect your phone to your computer via USB.
Go to control panel -> device manager after a few minutes
Right click on Zen Ultrafone and update drivers ... required drivers are attached in above link.
Your device manager should not normally have any unrecognized hardware after this step. ( see attached Image).
The"Android Composite ADB Interface" MUST be listed by now... if not recheck your steps again.
Disconnect and restart your phone and your computer and make sure it stays that way.
STEP 2 -INSTALL THE USB VCOM DRIVER
This driver helps the computer recognize the phone's flash memory when it is SWITCHED OFF.
Disconnect your phone and switch it off... remove battery and put it back in just to make sure.
Keep device manager in windows open.
Connect the phone now.
The computer should list the Preloader in device manager with a yellow triangle.
Right click and install the drivers... accept any prompts to install unsigned drivers as they appear.
Disconnect the phone..
STEP 3 - FLASH THE CWM RECOVERY
Download and extract SP Flash tools to a folder.
Place the scatter file and the recovery image in a separate folder
Open SP Flash tools select the scatter loading file given
CAREFULLY UNCHECK ALL BOXES EXCEPT RECOVERY!! - this is essential!!
Click on recovery and choose the recovery image provided
Press 'Download' button on SP Flash tools.... DO NOT hit the firmware update button...
Now reconnect your phone.... accept any prompts...
When the Green ring appears, you are done...
Please hit thanks..... and please JOIN the forum and leave some feedback...
Edit: - I am somehow unable to uplaod the CWM recovery to xda.... meanwhile i've uploaded it here..
https://docs.google.com/file/d/0B9ZlmxCxbtQ8UjhfX3ZYRFZmS3c/edit?usp=sharing
Alternate (easier) method
This method needs a rooted phone-
Install mobile uncle tools from Play Store.
Place the recovery.img provided in root of SD card.
open mobile uncle tools and flash the recovery.
Thats It!!
completely lost faith in zen uf 701 hd..
got a product which has few blue lines on the screen and camera not working.
made a refund and looking to buy any other quadcore.
canvas hd, canvas 2 plus, umi x2
which is better?
Sorry to hear that man. I dont believe the canvas is any better in terms of quality control. Where did you buy the ultrafone from? Mine came in pretty good packing.
Looks like I've lost a valuable developer resource
Sent from my ultrafone 701HD using xda app-developers app
I'd suggest you go for the Panasonic p51. Just wait a few more months - its price is falling by the day
Sent from my ultrafone 701HD using xda app-developers app
Hello all. Received my 701 HD a couple of days back . thankfully no defects in my piece. And phone Is awesome !
And I was really surprised you guys have already rooted And Made CWM ready ! My salutes bro....
Looking forward to root and try better ROms when this new mobile vanity wears off soon
BTW Is there an unrooting method present ? Maybe it will be if help looking at many complaints this phone has
Sent from my ultrafone 701HD using xda app-developers app
Haven't tried to in root it yet. Guess flashing the stock ROM will do.
Sent from my ultrafone 701HD
Oh yes... I Forgot that flashing stock ROM does the trick
But then I guess we will also have to remove the custom recovery to avail warranty . just in case ??
Sent from my ultrafone 701HD using xda app-developers app
Yes. For warranty, you'll have to restore everything to stock state. The stock recovery can be flashed via stools too. Just replace the cmw with the stock recovery in my tutorial.
Sent from my ultrafone 701HD
BTW. I am sure we can find a lot of clone phones of our zen 701. Notably canvas HD, xolo Q1000. Celkon signature HD
Maybe in near future we could port the best roms from them. What say ?
Sent from my ultrafone 701HD using xda app-developers app
That is the plan for now
Sent from my ultrafone 701HD
vishwasnp said:
BTW. I am sure we can find a lot of clone phones of our zen 701. Notably canvas HD, xolo Q1000. Celkon signature HD
Maybe in near future we could port the best roms from them. What say ?
Sent from my ultrafone 701HD using xda app-developers app
Click to expand...
Click to collapse
uploading fazhdv3 rom for zen 701 hd 74%
a copy of sam hd v3 of a116
http://forum.xda-developers.com/showthread.php?t=2201122
Guys. Is it only me or are you also noticing that Wi fi reception is very weak in this cell ? :banghead:
Sent from my ultrafone 701HD using xda app-developers app
No issues with WiFi here. Tried connecting through public hotspots , mobile thetering, used this phone as hotspot, used WiFi direct with super beam - all work like a charm.
Looks like my WiFi router has gone numb due to cold these days
Any suggestions to improve signal strength of router ? The weak signal is really testing my patience :banghead:
Sent from my ultrafone 701HD using xda app-developers app
Could be due to interference. Try a selecting manual frequency in router
Dudes. Have any of you guys installed custom Roms yet ? The pathetic streaming of YouTube from WiFi in this phone is testing my patience
Sent from my ultrafone 701HD using xda app-developers app
Is your WiFi issue resolved? I be never tried YouTube so far..... Will try and then update
I moved my router to a closer position now. It is better. Will observe for a few more days see how it performs
Sent from my ultrafone 701HD using xda app-developers app
dextrorotatrix said:
Hi all
I've managed to create a CWM recovery for the Zen Ultrafone 701HD..... Thought I'd share this too...
For my tutorial on Rooting the same phone see here :-
http://forum.xda-developers.com/showthread.php?t=2283125
See the above link to activate USB debugging and install ADB drivers.....
CREDITS:-
I've Tested the CWMr on my own Phone....It Works..
This was made through the resources already available on various threads in XDA..
All credits to the original developers...
Special thanks to Koush Dutta for his online CWM revovery builder.... works like a charm..
I take DO NOT responsibility for any damages - It worked on my phone, no reason it should
not work on the other 701HDs out there.... Take a backup of all important stuff... Better safe than sorry..
STEP 1 - INSTALL PHONE DRIVERS
Connect your phone to your computer via USB.
Go to control panel -> device manager after a few minutes
Right click on Zen Ultrafone and update drivers ... required drivers are attached in above link.
Your device manager should not normally have any unrecognized hardware after this step. ( see attached Image).
The"Android Composite ADB Interface" MUST be listed by now... if not recheck your steps again.
Disconnect and restart your phone and your computer and make sure it stays that way.
STEP 2 -INSTALL THE USB VCOM DRIVER
This driver helps the computer recognize the phone's flash memory when it is SWITCHED OFF.
Disconnect your phone and switch it off... remove battery and put it back in just to make sure.
Keep device manager in windows open.
Connect the phone now.
The computer should list the Preloader in device manager with a yellow triangle.
Right click and install the drivers... accept any prompts to install unsigned drivers as they appear.
Disconnect the phone..
STEP 3 - FLASH THE CWM RECOVERY
Download and extract SP Flash tools to a folder.
Place the scatter file and the recovery image in a separate folder
Open SP Flash tools select the scatter loading file given
CAREFULLY UNCHECK ALL BOXES EXCEPT RECOVERY!! - this is essential!!
Click on recovery and choose the recovery image provided
Press 'Download' button on SP Flash tools.... DO NOT hit the firmware update button...
Now reconnect your phone.... accept any prompts...
When the Green ring appears, you are done...
Please hit thanks..... and please JOIN the forum and leave some feedback...
Click to expand...
Click to collapse
My phone is not loading the image also unable to load the recovery file too. Can you please help me out where can i download the recovery.img file as the link you have provided does not have the same.
I have a Micromax A100 mobile which is out of warranty. I tried to update the ICS with Jb 4.1.1 and at that time the mobile got OFF and now I am not able to SWITCH ON the mobile .
I tried with VolDown + Power key at the same time to launch FASTBOOT and so many options like that. The mobile is not ON.
Actually at the time of installation of GRAND ROM V3, downloaded from this site, it got struck, showing the message ""ERROR 7, Installtion Aborted"". I manually operated the options ( dont exactly remember) and tried to REBOOT and then it got OFF and not SWITCHED ON till now for the past 10 days.
When I connect it to PC with USB Cable, it is NOT SHOWN as a device in MY COMPUTER but is showing in Device Manager as "Qualcomm HS-USB QDLoader 9008" . What does this mean and what to do to solve this issue.
If you people say it is BRICKED, what is the solution for this ?
How can I get back my phone back in ON condition ?
Thanking you in anticipation for a solution.
Murthy
vsrkmurthy said:
I have a Micromax A100 mobile which is out of warranty. I tried to update the ICS with Jb 4.1.1 and at that time the mobile got OFF and now I am not able to SWITCH ON the mobile .
I tried with VolDown + Power key at the same time to launch FASTBOOT and so many options like that. The mobile is not ON.
Actually at the time of installation of GRAND ROM V3, downloaded from this site, it got struck, showing the message ""ERROR 7, Installtion Aborted"". I manually operated the options ( dont exactly remember) and tried to REBOOT and then it got OFF and not SWITCHED ON till now for the past 10 days.
When I connect it to PC with USB Cable, it is NOT SHOWN as a device in MY COMPUTER but is showing in Device Manager as "Qualcomm HS-USB QDLoader 9008" . What does this mean and what to do to solve this issue.
If you people say it is BRICKED, what is the solution for this ?
How can I get back my phone back in ON condition ?
Thanking you in anticipation for a solution.
Murthy
Click to expand...
Click to collapse
Actually Ur fone is a110 or a100 .If u r having a100 and flashed grand v3 rom which is for a110 u have hard bricked the fone .Can u enter into the recovery mode ?? Do u have a NANDROID back up ?
You flashed a110 rom on a100? Well then, yes it's partially bricked, since your bootloader is working as per device manager , so you can try to flash stock rom ofA100 on it using a flash tool meant for it.
Sent from my potato chamber using xda app-developers app
mufti.arfan said:
You flashed a110 rom on a100? Well then, yes it's partially bricked, since your bootloader is working as per device manager , so you can try to flash stock rom ofA100 on it using a flash tool meant for it.
Sent from my potato chamber using xda app-developers app
Click to expand...
Click to collapse
Well it may be Hard bricked not Partially bricked As you told the bootloader wont work as per device layout u cant boot the phone :good:
vish97 said:
Well it may be Hard bricked not Partially bricked As you told the bootloader wont work as per device layout u cant boot the phone :good:
Click to expand...
Click to collapse
But it's being detected by his pc. He can try doing some work around to flash stock. But chances are very least.
Sent from my potato chamber using xda app-developers app
Micromax A100 Switch ON Problem.
Friends,
Many of you told many options. My issue is unless it is detected by the PC (as a device under my computer), we will not be able to do anything as per me.
The other day I tried to do something using QPST V.2.7.402 and there also, the phone was detected as per the COM2 but capturing is not done and hence there also I was not able to do .
Understood from our forum only about UNBRICK. What does it mean and will there be any use of having it ? Also downloaded EAZY JTAG today morning using the links from our forum. Is it at all useful for me ?
To let all you guys know, the phone has no problem at all prior to this ROM installation. Now, am not able to SWITCH it ON.
As asked by Mr VISH97, I don't have any backup or I am not able to switch on the phone, so where is the point of entering recovery mode ?
As you guys say BRICKED is there any other solution for get back to working ??
vsrkmurthy said:
Friends,
Many of you told many options. My issue is unless it is detected by the PC (as a device under my computer), we will not be able to do anything as per me.
The other day I tried to do something using QPST V.2.7.402 and there also, the phone was detected as per the COM2 but capturing is not done and hence there also I was not able to do .
Understood from our forum only about UNBRICK. What does it mean and will there be any use of having it ? Also downloaded EAZY JTAG today morning using the links from our forum. Is it at all useful for me ?
To let all you guys know, the phone has no problem at all prior to this ROM installation. Now, am not able to SWITCH it ON.
As asked by Mr VISH97, I don't have any backup or I am not able to switch on the phone, so where is the point of entering recovery mode ?
As you guys say BRICKED is there any other solution for get back to working ??
Click to expand...
Click to collapse
If the board is bricked, nothing can be done, other than jtag method. Which necessarily doesn't work every time.
Sent from my potato chamber using xda app-developers app
Huy guy. My lenovo a850 stok rom S203. I flas using sp flash tool to rom S121 have move app to sd for this rom. After flash complete. I on phone cannot. I plug usb to phone no deteck my phone. Press button on cannot to on. Remove batery plug usb red lamp on. Insert battery lamp off. Help me guy
Sent from my Lenovo A850 using XDA Free mobile app
aliutak said:
Huy guy. My lenovo a850 stok rom S203. I flas using sp flash tool to rom S121 have move app to sd for this rom. After flash complete. I on phone cannot. I plug usb to phone no deteck my phone. Press button on cannot to on. Remove batery plug usb red lamp on. Insert battery lamp off. Help me guy
Sent from my Lenovo A850 using XDA Free mobile app
Click to expand...
Click to collapse
Re-flash an other rom. And stop spamming the forum.
On the other hand, your phone do not work but it can post in XDA -.-