Database Info

Android 2.3.6 Firmware on Galaxy Pocket Duos S5302

Install Android 2.3.6 Firmware on Galaxy Pocket Duos S5302
Reminder
You will lose installed custom ROM such as CM10, Paranoid Android or AOKP after flashing official firmware. Custom ROM will be replaced by official stock ROM.
You will lose custom recovery such as ClockworkMod Recovery or TWRP Recovery if you have any. Custom recovery will be replaced by stock recovery. We will soon write on how to install ClockworkMod recovery on Galaxy Pocket Duos S5302. [Try search box at top-right to get it]
Your device no longer belongs to rooted device once you install this firmware. We will soon write on how to root Galaxy Pocket Duos S5302. [Try search box at top-right to get it]
Though official firmware update usually not erase any system data but we advise you to follow our pre-requisites mentioned on previous page as precaution.
This firmware released by Samsung and flashing of this won’t increase binary counter.
Download this - Click here-
2)Odin Download[
How to Update Galaxy Pocket Duos GT-S5302 to S5302JPLH2 Android 2.3.6 Official Firmware--:good::good:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Extract Firmware zip file that you downloaded already from above link, you will get a .tar file and some other files.
Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Now, put the Galaxy Pocket Duos GT-S5302 phone in Download Mode by pressing pressing and holding down the Volume Down and Home buttons while pressing the Power button until you are welcomed by a green robot indicating you are in Download Mode.
Now run Odin3 v3.07.exe (see Step 2) as an Administrator because Admin privileges is required to complete the process smoothly.
Now connect your Galaxy Pocket Duos GT-S5302 with your PC using USB cable. A message will arrive under Odin’s message box in the bottom left saying “Added!!”. If you don’t get the same then you should try another USB port (try USB port located in back in your desktop PC). If that too don’t work then you should then reinstall the driver. If you successfully see the “Added!!” message in Odin then you are ready to go in next step. You should also see COM port with a number in Yellow if you successfully added your device.
Select these files in Odin at respective tabs from extracted S5302JPLH2 firmware folder :
Click the PDA Button, and select the .tar file here with *code* appearing in its name
Click the Phone Button, and select file with *modem* in its name (leave if there is no such file)
Click the CSC Button, and select file with *csc* in its name (leave if there is no such file)
Click the PIT Button, and select the .pit file. Use only if you got it while extracting in step 1 above, otherwise ignore it.
In Odin window, make sure Auto Reboot and F. Reset Time checkboxes are selected. Also, make sure that Re-Partition checkbox is selected, only if you are using a .pit file (see Step 7.4).
Double check everything that we mentioned in Step 7 & Step 8 above. Now, once satisfied hit the START button to begin the flashing process.
Once flashing completed, you will see a PASS message with green background in the left-most box at the very top of the Odin. The phone will then automatically rebooted and soon you will see the Samsung logo. You can then unplug the USB cable to disconnect your device from computer.
Congrats! Your Galaxy Pocket Duos, model number S5302 should now run on Android 2.3.6 Gingerbread build JPLH2. Go to Settings > About phone to verify this firmware update.:good::good:

thanx bro

I didn't see any links?
Sent from my GT-S5300 using Tapatalk 2

luqman98 said:
I didn't see any links?
Sent from my GT-S5300 using Tapatalk 2
Click to expand...
Click to collapse
google it

Dont joke ok..where's the link

[GUIDE] Rooting Orange Pasadena Branded ALCATEL OT-918 (v2.3.6)

The guide is for the Alcatel OT-918 (No D, N, MIX), single sim, Orange Pasadena, from Romania with Gingerbread 2.3.6, it might work on other versions to, but I can't guarantee that.
Care should be taken, while the Orange Pasadena is a cheap phone, modifying your software might turn your device in an unusable brick.
Unfortunately the Android version of this phone can't be rooted with superoneclick or other simpler methods.
First of all You need the following tools from the attached file:
USB Drivers
SP_Flash_Tool_v3.1224.00
AlcatelScatterRetriever01 - optional
Universal recovery for Alcatel OT918 (2.3.5 and 2.3.6)
Superuser-3.0.7-efghi-signed.zip
http://dl.dropbox.com/u/74256292/Pasadena/Orange_Pasadena_OT918_root.zip
1. Turn off the phone, and connect it to the computer (Windows XP/7) with an USB cable, and install the attached drivers
2. Create a scatter file with AlcatelScatterRetriever01,
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
(alternatively you can skip this step and use the scatter file from the OT-918_Orange_Pasadena_Branded folder)
3. Run Flash tool and open the scatter file
4. Check only the recovery file from the OT-918_Orange_Pasadena_Branded folder
Double check that all other checkboxes must be unchecked!
5. Click on download
6. Connect the turned off phone to the computer, the progress bar should change its color and after a short while a small window with a green circle and ok should appear.
If it's not working remove USB cable, the battery, and reconnect the battery and then the USB cable and try again.
7. Remove the battery and the SD-card
8. Copy Superuser-3.0.7-efghi-signed.zip to the SD-card
9. Replace the SD-card and the battery
10. Start the phone with the Volume UP and Power combo (release first the power button)
11. You should be in the OT-918N recovery, and should install the file Superuser-3.0.7-efghi-signed.zip from the SD-card
12. Restart and enjoy your root-ed phone.
For UNROOT make a full wipe from recovery.
Repair information:
If you got an Orange Pasadena which would not boot or is in a bootloop, at step 4 select all the files from OT-918_Orange_Pasadena_Branded folder and go on with the guide.
At step 8 copy to the SD-card deepROM 2.3.6. from http://4pda.ru/forum/index.php?showtopic=323769&st=2320#entry16968462 ,
the file from http://disk.yandex.com/public/?hash=%2BFgTiMPQgqQjcFeH30tIoZnLBEVANGQz3%2BeBBWub5m0%3D ,
which is the only functional custom rom as far as I know for this model of the phone.
If someone needs a functional (but incomplete) stock image feel free to p.m. me.
Still searching for a full stock image, which will be posted here.
Thanks to qwe-, Linerty, elpopa, jman0, deep4512, breakk, @zoyB, cappa72, and all other who contributed to this guide.

Drivers
Hello,
At step "1: Turn off the phone, and connect it to the computer (Windows XP/7) with an USB cable, and install the attached drivers"
Witch one of the drivers should I install? I've tried everything, but the phone it is not recognized by the XP OS, and therefore the ASR.exe cannot generate the scattering file.
Please help, with more detailed procedure regarding the drivers.
Thank you,
Stro

It works, thank you!

Is there anyway to install another, more stable, Rom.
Maybe an original OT-918 ROM?
Thanks.

guys, i'm trying to reinstall an ot-918 device, with luck, but now the sim doesn't work (I have an network issue). what can I do?
also I've tried to follow this tutorial to add the IMEI back ('cause now is null), but without any luck (I don't have any "write imei" button). can someone help me out please?

[Q] is this how i root mGalaxy Tab 2 P3110 - 16gb wifi only

instruction source - http://www.ibtimes.co.uk/articles/4...70-p3110-root-android412-xxdma2-jellybean.htm
I bought my gtab2 few days back. It runs jellybean 4.1.2 Indian version, after going through different outdated rooting guides i thought it would be better if i ask this here. I am about to root my gtab2 following the ibntimes guide . Please tell me if i should do something different or if there's a better way to root. The guide looks fairly simple and straightforward though.
tab properties -
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
1) Install USB Driver for Samsung Galaxy Tab 2 7.0 on the computer.
2) Enable USB Debugging Mode. [Press Menu>> Settings>> Applications. From there navigate and click on Development option and ensure the USB Debugging Mode is turned on.]
3) Rooting the tablet will void manufacturer's warranty.
4) The rooting is likely to increase binary counter.
5) Create back-up for all the data of the device.
6) The tablet should have more than 80 per cent of charge.
Steps to root Galaxy Tab 2 7.0 P3110 on Android 4.1.2 XXDMA2 Jelly Bean
1) Download CF-Auto-Root file for Samsung Galaxy Tab 2 7.0 to the computer. Extract the downloaded zip to get a .tar.md5 file
2) Download Odin 3.07 and extract the zip to get Odin3 v3.07.exe along with few other files
3) Switch off the Galaxy tablet. Put the device into Download Mode by pressing and holding the Volume Down and Power buttons together. A warning screen will appear, now press the Volume Down button to enter into Download Mode
4) Run Odin on the computer
5) Connect the Galaxy tab to the computer using USB cable while it is in the Download Mode. A message saying 'Added' will arrive under Odin's message box. When the device is connected successfully, the COM port with a number in Yellow will also appear
[Note: If the 'Added' message does not come then try another USB port. Try the port located at the back side of the computer. In case that does not work too then reinstall USB driver.]
6) In Odin, click the PDA button and select 'CF-Auto-Root-espressowifi-espressowifixx-gtp3110.tar.md5' file
7) Ensure the Auto Reboot and F.Reset Time options are selected in Odin
8) Double check everything and click the Start button in Odin to begin the installation
9) Once the installation process is completed, the device will reboot automatically. And soon a 'PASS' message with green background will appear in the extreme left box at the top of the Odin. Now safely unplug the USB cable from the tablet
Samsung Galaxy Tab 2 7.0 P3110 running on Android 4.1.2 XXDMA2 Jelly Bean firmware is now rooted successfully. To ensure the aforementioned root method is installed and working properly, verify with the Root Checker app which is available at Google Play Store.

There are lots of tuts for rooting already, we dont need another.
Sent from my GT-P3110 using xda app-developers app

sorry for being a bother .. this is the same guide posted by chainfire just rehashed by ibn.

itsrijo said:
sorry for being a bother .. this is the same guide posted by chainfire just rehashed by ibn.
Click to expand...
Click to collapse
To answer your question, yes the guide still works.
Sent from my GT-P3110 using xda app-developers app

[Completed] Samsung S3 Neo GT-I9300I KitKat 4.4.4 Update

Hello everyone today I found Samsung S3 Neo GT-I9300I KitKat 4.4.4 Update,now no more just go install official kitkat on your S3 Neo GT-I9300I and video tutorial of how to udate it...
Steps to Install Android 4.4.4 KitKat Update on Galaxy S3 Neo I9300I
Step 1- Download Android 4.4.4 I9300IXXUBNH3 for Galaxy S3 Neo on computer and extract the zip file.
Step 2- Download ODIN v3.09 which is needed to install Android 4.4.4 on Galaxy S3 Neo.
Step 3 – Power off your phone and boot it into Download mode. To do so, press and hold Volume Down and Home buttons together, and then hit Power button till you see the construction Android robot and a triangle. Then tap Power again to confirm progress into Download Mode.
Step 4 - Ensure Galaxy S3 Neo USB drivers are installed on your computer.
Step 5 - Launch ODIN on computer and connect your phone to it while your phone is still in Download Mode.
Step 6 - Once the phone connects successfully, one of the ID: COM boxes will turn yellow with the COM port number. This step may be time consuming.
Step 7 - Now choose the files that need to be flashed / installed on your phone, which can be found among the extracted files in Step 1.
Click on 'AP' and select file named 'CODE'.
Click on 'CP' and select file named 'MODEM'.
Click on 'CSC' and select file with CSC' in its name.
Click on 'PIT' and select the .pit file.
Note: Ignore the last three steps if the files are missing.
Step 8 - In ODIN, select the Auto Reboot and F. Reset Time options. But, the Re-Partition option must be checked ONLY if you chose a .PIT file in the above step.
Step 9 - Now click on the Start button in ODIN and the installation process will begin. It should take just a few minutes to complete.
Step 10 - After the installation is completed, your phone will restart. When the home screen appears, just unplug your phone from the computer.
Your Samsung Galaxy S3 Neo has now been updated to Android 4.4.4 build XXUBNH3 OTA firmware. Go to Settings > About phone to verify the firmware installed,and change the language you prefer becuse it is set as default language to Kaizi and thats it...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
[YOUTUBEhttp://youtu.be/r8--WcWriTI][/YOUTUBE]
Please Press Thanks If You Like it...

Good of you to post here. But It should really be posted in Galaxy S III General forum for the users of that device.

[Completed] error occured during flashing stock rom in k5 plus

Sahara fail error occurred in lenovo k5 plus...

XDA Visitor said:
Sahara fail error occurred in lenovo k5 plus...
Click to expand...
Click to collapse
i have not tried this method but this is what i could come across while searching in xda forums....
you may also register yourself at XDA and search more or check this thread http://forum.xda-developers.com/android/general/unbrick-vibe-k5-plus-qfil-qpst-method-t3467830
IMPORTANT : First of all you should always have all the drivers installed on your PC.
READ EVERYTHING CAREFULLY AND MAKE SURE YOU HAVE FOLLOWED THE STEPS CAREFULLY AND THEN POST QUERIES.[/COLOR]
The following drivers are needed for this task:
1. Lenovo USB Drivers.
2. QDLoader QFIL Drivers
Search for them on google and you will find them very easily. Most of the time they are there in the stock rom zip folder under a folder named Drivers.
Install all of them.
1. Download the Stock ROM you need for your phone from here:
DOWNLOAD STOCK FIRMWARE (Thanks to Shreps)
2. Extract the above zip to a folder. You will get three folders: Drivers, Images and Tools.
3. From the Drivers folder, Install all drivers.
4. From the Tools folder, install the QPST Tool. In your Start Menu it will come as QFIL. Don't worry about that.
5. Power Off your device.
6. Open QFIL TOOL.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
7. Now On top you will see two options: 1. Flat Build 2. Meta Build
Select FLAT BUILD
8. In "PROGRAMMER PATH" click Browse and go to the folder named Images and select the one file it displays (something like prog_emmc....mbn).
9. Now click "Load XML" and select "rawprogram0.xml" file and then another dialog box will open. Here select "patch0.xml".
PC WORK IS DONE. DO NOT CLICK DOWNLOAD.
Your device should be switched off.
NOTE CAREFULLY: Hold "VOLUME UP + VOLUME DOWN" key (Do not press POWER button). and connect the USB Cable from PC to the phone.
Your phone should now display RED LED LIGHT and the QFIL Tool should now change from NO PORT to QUALCOMM.....Something like that.
You are now ready. Click on Download button on QFIL TOOL and then wait for atleast 15 minutes.
After the dialog at bottom shows "DOWNLOAD SUCCESSFUL" in blue color, UNPLUG your device. Wait for a few seconds or a minute and then POWER ON your device.
First boot takes about 8-10 minutes.