I have a Galaxy Tab 2 (P5113) that won't boot at all. I can get it into Download mode, but not recovery. I have tried using ODIN to flash a new recovery and a complete ROM and it usually errors out with and error of NAND write error, (Successful 0, Failed 1). I have tried multiple ROMs and a couple of recoveries to no avail. I have installed KIES and made sure it wasn't running in the back ground. I even tried to flash a PIT and it gets to a point that says there is no PIT partition. Any thoughts? All help would be appreciated. Thanks.
flash with latest recovery use twrp
krishna fattepurkar said:
flash with latest recovery use twrp
Click to expand...
Click to collapse
I'll give twrp a try.
Tried twrp. Still getting the same error. Here is a screenshot of it.
natebarrett said:
I'll give twrp a try.
Click to expand...
Click to collapse
failed at nand write .
This can be for a number of reasons , the least serious being:
1. Are you sure your phone is not locked to a network ?
2. Did you use an original USB cable ?
3. Did you connect directly to USB port of computer and not a
usb hub ?
4. Try another USB port on your computer ?
1. This a wifi only version so no carrier.
2. It is the original cable
3. Connecting directly to the computer, but I am using the front ports on a tower. I will give the rear ports atry.
4. Used both front ports, but will give the rear ports a try.
Thanks for the thoughts.
krishna fattepurkar said:
failed at nand write .
This can be for a number of reasons , the least serious being:
1. Are you sure your phone is not locked to a network ?
2. Did you use an original USB cable ?
3. Did you connect directly to USB port of computer and not a
usb hub ?
4. Try another USB port on your computer ?
Click to expand...
Click to collapse
I have the same problem. I don't even get the samsung animation. if I have it conected to the wall I sometimes get battery image but it doesn't move . If I hold down only the power button when not connected to power, I get nothing. I also get the "Firmware update encountered an error" I can get to download mode and it says
ODIN MODE
PRODUCT NAME: GT-P5113
CUSTOM BINARY DOWNLOAD: YES (72 COUNTS)
CURRENT BINARY: CUSTOM
HHEEEEELLLLLLLLLLLLPPPPPPPPPPPPPP!!!!!!!!!!!!!!!
weedhed4life said:
I have the same problem. I don't even get the samsung animation. if I have it conected to the wall I sometimes get battery image but it doesn't move . If I hold down only the power button when not connected to power, I get nothing. I also get the "Firmware update encountered an error" I can get to download mode and it says
ODIN MODE
PRODUCT NAME: GT-P5113
CUSTOM BINARY DOWNLOAD: YES (72 COUNTS)
CURRENT BINARY: CUSTOM
HHEEEEELLLLLLLLLLLLPPPPPPPPPPPPPP!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
Flash a stock firmware on your tab, your current binary says custom.. If it was a samsung rom it would have said samsung official..
Use ODIN to flash the firmware..
---------- Post added at 11:45 PM ---------- Previous post was at 10:47 PM ----------
And dont forget to charge it first.. even if you dont get the proper charging icon.. just leave it pluged in for an hr or so..
Sent from my GT-I9300 using xda app-developers app
weedhed4life said:
(...)
CUSTOM BINARY DOWNLOAD: YES (72 COUNTS)
(...)
Click to expand...
Click to collapse
Not bad 72 Odin flashes
Maybe you bricked something? EFS?
P5113 frustration
Android-Andi said:
Not bad 72 Odin flashes
Maybe you bricked something? EFS?
Click to expand...
Click to collapse
What do you mean? Bricked EFS? I have tried several times to do an Odin flash to stock. It says that it was successful and then turns off, only to come back on to the "firmware update encountered an error" I then have to flash a kernel to get it to even go into download mode. I am curious about something called omap flasher. I wonder if I can use that to get the thing working
Related
Gentlemen,
Please I updated my note 10.1 2012 GT-N8000 to kitkat 4.4.2 without rooting or usb debugging enable, then during charging it, i forget it around four hours it restarted, and all the time in download mode, i used odin, failed to open Com port, i tried to enter to recovery, failed. i tried to enter to bootloader, i thing it is locked, also when i tried to use odin, it tells that no PIT is found, any suggestion? (changed usb cable, uninstall kies and install usb samsung drivers, used different versions of odin with CSC,Bootloader, PIT ,PDA,modem, files etc... ) all are failing, seems that it is just locking itself... the only place i can enter, is when i enter press power button, and - volume (Volume downn), it would take me to ODIN MODE , Product name: GT-N8000, Currnet Binary: Custom, System Status: Official, RP SWREV: A2 and it is all the time Downloading Do not turn off target, even i tried to uninstall the battery for sometime, and i put it again... and if just insert it to the usb it would start directly to Firmware upgrade encountered an issue, please select recovery mode (which i can't enter to it, failed to enter by power + volume up) in kies & try again, also the initialization of kies is not supported, if used...
What are you trying to flash with Odin? Try official
And if the device actually pops up in Odin and the COM port is through then the cable and the hardware is all fine.
raedzahr said:
Gentlemen,
Please I updated my note 10.1 2012 GT-N8000 to kitkat 4.4.2 without rooting or usb debugging enable, then during charging it, i forget it around four hours it restarted, and all the time in download mode, i used odin, failed to open Com port, i tried to enter to recovery, failed. i tried to enter to bootloader, i thing it is locked, also when i tried to use odin, it tells that no PIT is found, any suggestion? (changed usb cable, uninstall kies and install usb samsung drivers, used different versions of odin with CSC,Bootloader, PIT ,PDA,modem, files etc... ) all are failing, seems that it is just locking itself... the only place i can enter, is when i enter press power button, and - volume (Volume downn), it would take me to ODIN MODE , Product name: GT-N8000, Currnet Binary: Custom, System Status: Official, RP SWREV: A2 and it is all the time Downloading Do not turn off target, even i tried to uninstall the battery for sometime, and i put it again... and if just insert it to the usb it would start directly to Firmware upgrade encountered an issue, please select recovery mode (which i can't enter to it, failed to enter by power + volume up) in kies & try again, also the initialization of kies is not supported, if used...
Click to expand...
Click to collapse
Download a N8000 firmware which comes packed in zip
extract it and then select it with AP in odin,
flash and wait until you're done
and if it is struggling with the port try another one
Download the official firmware for your model number regardless of the region (that is if you're ok with it otherwise use your own region's)
Then use the appropriate Odin version to flash the firmware to your device while in download mode. Put the Firmware file into PDA/AP.
Make sure Reartition is not ticked otherwise your device will be bricked. (Lol it rhymes)
Make sure the cable connection is stable and don't disconnect the connection until the process of flashing is done.
Not advertising but you can find your firmware at Sammobile. It tells you which Odin version to use too. I'm not sure if Odin version matters but let's play safe.
Hope this helps.
Sent from my SM-A300F using XDA Free mobile app
bernardwu said:
Download the official firmware for your model number regardless of the region (that is if you're ok with it otherwise use your own region's)
Then use the appropriate Odin version to flash the firmware to your device while in download mode. Put the Firmware file into PDA/AP.
Make sure Reartition is not ticked otherwise your device will be bricked. (Lol it rhymes)
Make sure the cable connection is stable and don't disconnect the connection until the process of flashing is done.
Not advertising but you can find your firmware at Sammobile. It tells you which Odin version to use too. I'm not sure if Odin version matters but let's play safe.
Hope this helps.
Sent from my SM-A300F using XDA Free mobile app
Click to expand...
Click to collapse
My phone was on a 4.4.2 custom rom when the same incident as the op happened. Where can I find the official firmware for 4.4.2?
Hi xda members, im new in here and i was hoping for a bit of help
My phone is galaxy s6 SM-920T
I was reading on the net when the phone powered off and started restarting and restating again and stuck at book logo "powered by samsung".
I am not able to go into recovery mode but i can open the os download mode.
Tried many times with odin and no luck
I think due to the phone being full encrypted by me nothing can be done, is there any posibility? Thanks
The same here. I cant get into recovery. I had Terminator Rom installed. I can get into download mode but odin doesnt detect it. I eventoght the usb door was damadged so paid 60$ do replace it at samsung. But odin still doesnt not recognize it. Odin does recognize my Samsung Tablet 4.
crazyportuguese said:
The same here. I cant get into recovery. I had Terminator Rom installed. I can get into download mode but odin doesnt detect it. I eventoght the usb door was damadged so paid 60$ do replace it at samsung. But odin still doesnt not recognize it. Odin does recognize my Samsung Tablet 4.
Click to expand...
Click to collapse
Flash stock OJC firmware with Odin http://imeirescue.com/samsung-firmw...galaxy-s6-stock-firmwares//url]
Report back.
IMEIRescue said:
Flash stock OJC firmware with Odin http://imeirescue.com/samsung-firmw...th a galaxy tab i have.
Thanks for your help
Click to expand...
Click to collapse
crazyportuguese said:
Odin doesnt not detect the phone on download mode.
Any tip ?
I have tryed all cables and that worked with a galaxy tab i have.
Thanks for your help
Click to expand...
Click to collapse
Have you made sure you have the latest Samsung drivers installed on your computer?( http://developer.samsung.com/technical-doc/view.do?v=T000000117) And after that, try to see if Odin recognize it download mode, after you have confirmed you wanna flash new Rom ( volum up)
crazyportuguese said:
Odin doesnt not detect the phone on download mode.
Any tip ?
I have tryed all cables and that worked with a galaxy tab i have.
Thanks for your help
Click to expand...
Click to collapse
I've had cases where you had to put the phone into download mode THEN open Odin for it to be seen. Maybe try that.
With it in download mode and plugged up open devices and printers and scroll to bottom and see if it shows up. Would be called gadget_serial. Some computers take a while to load the drivers for it as well. You may want to click little popup menu on bottom right of desktop by the time and date and see if it shows it is loading drivers for it. It will not show up until the gadget serial drivers are installed.
Thanks for the help. Nothing worked. It doesnt not recognizes the S6 only my Galaxy Tab 4. Could it be that the usb door wasnt repaired proprely ? Windows doesnt even detect the phone no gadget_serial. Nothing.
Make sure that You're using USB 2.0 not 3.0. My Note 4 worked through usb3.0 without any problem. And S6 doesn't. And if Odin reflash won't fix it. Get pit file and flash it with it.
ProtoDeVNan0 said:
Make sure that You're using USB 2.0 not 3.0. My Note 4 worked through usb3.0 without any problem. And S6 doesn't. And if Odin reflash won't fix it. Get pit file and flash it with it.
Click to expand...
Click to collapse
you need samsung drivers and check the cable.
Any help for me?
crazyportuguese said:
Thanks for the help. Nothing worked. It doesnt not recognizes the S6 only my Galaxy Tab 4. Could it be that the usb door wasnt repaired proprely ? Windows doesnt even detect the phone no gadget_serial. Nothing.
Click to expand...
Click to collapse
So it doesn't recognize it all all? Doesn't give you unable to read device error or anything?
---------- Post added at 07:20 PM ---------- Previous post was at 06:49 PM ----------
yyyy0000zzz said:
you need samsung drivers and check the cable.
Any help for me?
Click to expand...
Click to collapse
First thing to try would be flashing stock firmware with Odin.
https://www.dropbox.com/s/rb8iduv2o9i1ece/G920TUVS3DOJC_G920TTMB3DOJC_TMB.zip?dl=0
I recommend Odin 3.10.6
https://www.dropbox.com/s/1dlmxtc0ic7u7ew/Odin3_v3.10.6.zip?dl=0
Report back.
already done, with same results stuck at boot loop, tried to add a custom recovery which got denied by knox
yyyy0000zzz said:
already done, with same results stuck at boot loop, tried to add a custom recovery which got denied by knox
Click to expand...
Click to collapse
Sounds like DRK may be damaged.
Take the stock OKC firmware and open the archive with 7-zip or winrar and extract the system.img and boot.img.
Download and unzip this:
https://www.dropbox.com/s/bsreazoonsw4gwv/tar-Tool_Odin3-v3.07_by_mkh.mourad.zip?dl=0
Copy/paste the system.img and boot.img into the software directory and run the batch file. It will spit out a system.tar.md5 and boot.tar.md5
Flash the system.tar.md5 with Odin as AP then flash the boot.tar.md5 as AP.
Report back
thank you gonna have to try tomorrow due to bad USB cables, will let you know thank you so much for your help
If all else fails, just boot your phone into download phone and install Samsung Kies and restore it using that.
You will need the model & serial number of your phone. It will restore the latest stock firmware on your phone for you..
fOmey said:
If all else fails, just boot your phone into download phone and install Samsung Kies and restore it using that.
You will need the model & serial number of your phone. It will restore the latest stock firmware on your phone for you..
Click to expand...
Click to collapse
how can I check the serial number WITHOUT my box and booting into the phone? my phone's bricked as hell
joshua44 said:
how can I check the serial number WITHOUT my box and booting into the phone? my phone's bricked as hell
Click to expand...
Click to collapse
You cant, I suggest using a friend or family member's serial number that has the same model phone.. the serial number is a way of identifying the correct carrier specific rom.
G920TUEU3COK1_G920TXAR3COK1_G920TUEU3COK1_HOME.tar.md5
G920T1UVU3DOI5_G920T1TMB3DOI5_G920T1UVU3DOI5_HOME.tar.md5
Reflash your phone with one of this ROM will help you to make your problem resolved 100%
Hi All, first post here and I'm 90% sure this is the wrong thread but I can't post in the ROMs, KERNAL, RECOVERIES thread....
Let me get to the point, I have a Galaxy S7 Edge (SM-G935W8) that won't show anything on the screen at all. No backlight or anything. I've tried using Odin to reflash the original ROM but keep failing on the re-partition. (Holding vol down, power and home will enter download mode and a solid blue light shows. The PC does recognize the phone but ADB doesn't since USB debugging wasn't enabled.)
Any ideas or is the NAND completely shot?
Thanks.
Tried repair via Smart Switch?
It tries to connect then says unsupported device. Emergency reset asks for a key...
DMSIMONE said:
Hi All, first post here and I'm 90% sure this is the wrong thread
Click to expand...
Click to collapse
Completely wrong forum too lol
https://forum.xda-developers.com/s7-edge
ADB being enabled has nothing to do with Download mode, as Download mode is independent to the firmware
Make sure you're using ODIN 3.12.3 or newer, and that the COM port on ODIN is showing as connected
It's not 100% that the phone is entering DL mode though if you have no display
---------- Post added at 21:12 ---------- Previous post was at 21:11 ----------
DMSIMONE said:
It tries to connect then says unsupported device. Emergency reset asks for a key...
Click to expand...
Click to collapse
Key is your device serial number iirc
Back of phone
I can get it to connect to ODIN.
COM port shows along with "Added!" but it always fails at the repartition step. (I'm adding all 4 of the files at once I believe that is correct?)
DMSIMONE said:
I can get it to connect to ODIN.
COM port shows along with "Added!" but it always fails at the repartition step. (I'm adding all 4 of the files at once I believe that is correct?)
Click to expand...
Click to collapse
Yep that's correct, are you trying to flash the same CSC or different?
Different CSC you might need to check the "Re-partition" option in ODIN settings as they can be different sizes
But no display in Download mode = Not a firmware problem, almost certainly a hardware problem
Alright, looks like I'm buying a parts phone and doing some surgery tonight. Thanks for the help!
Good luck
I have a bricked S8+ stuck on samsumg logo (labeled as SM-G9550 on backside label), but when i boot into download mode, it shows "PRODUCT NAME: SM-G955N", How this could possible, when i check the imei on the web, it result SM-G9550 as product name
flashing "N" firmware with odin result PASS, but still stuck on logo..
i can't flash 9550 firmware as it shows error "Secure Check Fail: PIT"
FYI, when i go to recovery mode, the screen goes to "Kernel Panic Upload Mode"
please help if anyone here has information about it
ryantprawira said:
I have a bricked S8+ stuck on samsumg logo (labeled as SM-G9550 on backside label), but when i boot into download mode, it shows "PRODUCT NAME: SM-G955N", How this could possible, when i check the imei on the web, it result SM-G9550 as product name
flashing "N" firmware with odin result PASS, but still stuck on logo..
i can't flash 9550 firmware as it shows error "Secure Check Fail: PIT"
FYI, when i go to recovery mode, the screen goes to "Kernel Panic Upload Mode"
please help if anyone here has information about it
Click to expand...
Click to collapse
Try doing the carrier switch method first then downloading and installing the unlocked firmware afterwards via odin. Make sure you download the 955U1 Odin firmware and NOT the 950U. Also can you upload a screenshot of what it shows in download mode
creglenn said:
Try doing the carrier switch method first then downloading and installing the unlocked firmware afterwards via odin. Make sure you download the 955U1 Odin firmware and NOT the 950U. Also can you upload a screenshot of what it shows in download mode
Click to expand...
Click to collapse
Thanks for your reply, so far the device only accept 955N firmware only, but nothing happen after falshing , why you suggest to download 955U1? will it work?
do you mind to give me a link how to do the carrier switch? I will search it on inet while u replying this post
ht**s://ibb.co/jitLV7
ht**s://ibb.co/jWjiiS
ryantprawira said:
Thanks for your reply, so far the device only accept 955N firmware only, but nothing happen after falshing , why you suggest to download 955U1? will it work?
do you mind to give me a link how to do the carrier switch? I will search it on inet while u replying this post
ht**s://ibb.co/jitLV7
ht**s://ibb.co/jWjiiS
Click to expand...
Click to collapse
You have the Korean model not sure why it has a 950 on the back. But you need to use the 955F firmware. Flash that thru odin
creglenn said:
You have the Korean model not sure why it has a 950 on the back. But you need to use the 955F firmware. Flash that thru odin
Click to expand...
Click to collapse
i tried, but blocked becouse of pit.. errors occur "SECURE CHECK FAIL: (PIT)"
ryantprawira said:
i tried, but blocked becouse of pit.. errors occur "SECURE CHECK FAIL: (PIT)"
Click to expand...
Click to collapse
Are you using the new Odin 3.13.1, if you are or not try removing the Samsung USB drivers and then restarting the computer. Then re-download the USB drivers and firmware.
ryantprawira said:
i tried, but blocked becouse of pit.. errors occur "SECURE CHECK FAIL: (PIT)"
Click to expand...
Click to collapse
I had the same issues flashing my 8+ . . . pit issues.
I found that a different USB cable worked, and also:
Go to download mode, start odin, load TWRP or other file, press start and then press pwn dwn, bixby and power, Odin will fail, but........
because you you went back into download mode, Odin will succeed next time you flash.
For some reason if I just acknowledged that Odin was going to fail on the first attempt, I kept the phone connected and did the routine, and on the second flash attempt, no more Pit file errors for me.
creglenn said:
Are you using the new Odin 3.13.1, if you are or not try removing the Samsung USB drivers and then restarting the computer. Then re-download the USB drivers and firmware.
Click to expand...
Click to collapse
I'm using odin 3.12, sounds promising, i will give it a try, thanks for the tips..
JeffDC said:
I had the same issues flashing my 8+ . . . pit issues.
I found that a different USB cable worked, and also:
Go to download mode, start odin, load TWRP or other file, press start and then press pwn dwn, bixby and power, Odin will fail, but........
because you you went back into download mode, Odin will succeed next time you flash.
For some reason if I just acknowledged that Odin was going to fail on the first attempt, I kept the phone connected and did the routine, and on the second flash attempt, no more Pit file errors for me.
Click to expand...
Click to collapse
i have try this combination but still failed, i guess the flash are blocked because FRP lock is "ON", since i can't go into the system or recovery mode, i have no idea how to turn off the FRP lock...
if you guys have a tricks how to turn off the frp lock via download mode, i think the flash should work without any doubt..
Ok so I went to flash twrp recovery onto my phone and something went wrong while using oden... My usb debugging is turned on and OEM Unlocked. Now my phone screen stays completely black. Its caught in a bootloop and No buttons work to bring it back into download mode, Only Upload mode works.. But Odin will not flash anything to my phone in Upload mode. It changes my samsung usb drivers to msm upload or modem drivers. I have been at this for weeks trying to get my s8+ to attach to my computer again using ADB, ODIN, SD CARD, AND EVEN THAT JIG Thing to force it into download mode but TO NO AVAIL.. I Have to some how get back into download mode but no button combinations will work.. It seems to bootloop on me before it reaches those commands. The bootloader is obviously gone to a certain degree since upload mode still works.. Is there any way to use Odin in upload mode? Or is there any other way I can reflash stock rom to fix this issue? I have no recovery, no safe mode, no download mode?? My phone is basically a paper weight right now.. When I know All my stuff is still on there. This S8+ Phone has put up a good fight with me on my pc But Im not one to loose. I love a good challange.. Any suggestions. I thought ADB Was my best bet but with no connect I cant do any thing. I cant' get Adb to find my device. Oh even tryed older versions of odin with low level quallcom drivers and that didn't work either. Odin will read a com port to my device but i'm in the wrong mode (Upload Mode) and Odin cant establish a connection. When in Upload Mode its the hellish one as xda deveopers have said before..
S8+ phone is Model Number SM-G950U
Witch I believe has now been upgraded to SM-G955U OR F.. But I have the original stock rom still for SM-G950U if only I can get into some kind of Download Mode.
Ive even sat watching odin as I push every single button combination watching the ports appear and dissapear as it reboots trying to find some kind of way to download to the phone... But no luck..
UNKNOWN ERROR
DDR VENDER : UNKNOWN
SOC_HW_REVISION : 2.1
SKIP PRINT_SUMMERY_TO_LCD
GENERATING SUMMERY........
GENERAL INFO
DDR INFO
DCVS INFO
RPM INFO
RECOVERED FROM AN EXCEPTION
DONE
Then if I hold the up button for a few seconds I get this underneath
SYNCHRONOUS EXCEPTION
LR : 0x0000000085e36d98
sp : 0x000000001407bbb0
pc : 0x0000000085e36df8
Not sure what that means or how to look up those codes but I know its all bad.. If anyone can think of any other way to connect my phone to reflash stock rom to fix Please let me know any theories or suggestions you may have for me to try... Thank You...
Gkeplar said:
Ok so I went to flash twrp recovery onto my phone and something went wrong while using oden... My usb debugging is turned on and OEM Unlocked. Now my phone screen stays completely black. Its caught in a bootloop and No buttons work to bring it back into download mode, Only Upload mode works.. But Odin will not flash anything to my phone in Upload mode. It changes my samsung usb drivers to msm upload or modem drivers. I have been at this for weeks trying to get my s8+ to attach to my computer again using ADB, ODIN, SD CARD, AND EVEN THAT JIG Thing to force it into download mode but TO NO AVAIL.. I Have to some how get back into download mode but no button combinations will work.. It seems to bootloop on me before it reaches those commands. The bootloader is obviously gone to a certain degree since upload mode still works.. Is there any way to use Odin in upload mode? Or is there any other way I can reflash stock rom to fix this issue? I have no recovery, no safe mode, no download mode?? My phone is basically a paper weight right now.. When I know All my stuff is still on there. This S8+ Phone has put up a good fight with me on my pc But Im not one to loose. I love a good challange.. Any suggestions. I thought ADB Was my best bet but with no connect I cant do any thing. I cant' get Adb to find my device. Oh even tryed older versions of odin with low level quallcom drivers and that didn't work either. Odin will read a com port to my device but i'm in the wrong mode (Upload Mode) and Odin cant establish a connection. When in Upload Mode its the hellish one as xda deveopers have said before..
S8+ phone is Model Number SM-G950U
Witch I believe has now been upgraded to SM-G955U OR F.. But I have the original stock rom still for SM-G950U if only I can get into some kind of Download Mode.
Ive even sat watching odin as I push every single button combination watching the ports appear and dissapear as it reboots trying to find some kind of way to download to the phone... But no luck..
UNKNOWN ERROR
DDR VENDER : UNKNOWN
SOC_HW_REVISION : 2.1
SKIP PRINT_SUMMERY_TO_LCD
GENERATING SUMMERY........
GENERAL INFO
DDR INFO
DCVS INFO
RPM INFO
RECOVERED FROM AN EXCEPTION
DONE
Then if I hold the up button for a few seconds I get this underneath
SYNCHRONOUS EXCEPTION
LR : 0x0000000085e36d98
sp : 0x000000001407bbb0
pc : 0x0000000085e36df8
Not sure what that means or how to look up those codes but I know its all bad.. If anyone can think of any other way to connect my phone to reflash stock rom to fix Please let me know any theories or suggestions you may have for me to try... Thank You...
Click to expand...
Click to collapse
You have a 950 u locked bootloader. First mistake trying to flash twrp. Only option you have is finding the revision bootloader you where on edl files and pinout to 9008 edl mode. There as of last known no fix other than for upload mode only.
Thank You
TheMadScientist said:
You have a 950 u locked bootloader. First mistake trying to flash twrp. Only option you have is finding the revision bootloader you where on edl files and pinout to 9008 edl mode. There as of last known no fix other than for upload mode only.
Click to expand...
Click to collapse
Thank You I will try that And reply back with results
Gkeplar said:
Thank You I will try that And reply back with results
Click to expand...
Click to collapse
What revision bootloader was it on? I have several of them but not all
TheMadScientist said:
What revision bootloader was it on? I have several of them but not all
Click to expand...
Click to collapse
It was on its original bootloader for the Samsung Galaxy S8+ SM-G950U. It was SnapDragon bootloader
TheMadScientist said:
What revision bootloader was it on? I have several of them but not all
Click to expand...
Click to collapse
I'm working on reading this thread now trying to follow there instructions, https://forum.xda-developers.com/galaxy-s8/help/s8-g950u-hardbrick-t3668572
Gkeplar said:
It was on its original bootloader for the Samsung Galaxy S8+ SM-G950U. It was SnapDragon bootloader
Click to expand...
Click to collapse
Mate there are 7 different revisions of the 950 u bootloader. Across all the software updates. No offense intended. But if you can't even give this little bit of info I can assure you. Your not gonna be able to dissemble this device. Ground out the test points to enter edl. And flash needed repair files. Which is very tedious. If there is any issues. I would mark this device as lost and get another. I dont feel that you have the necessary skills needed to complete this process...
---------- Post added at 10:49 PM ---------- Previous post was at 10:38 PM ----------
Gkeplar said:
I'm working on reading this thread now trying to follow there instructions, https://forum.xda-developers.com/galaxy-s8/help/s8-g950u-hardbrick-t3668572
Click to expand...
Click to collapse
Unless you are on revision 2 bootloader that is no use to you
---------- Post added at 10:51 PM ---------- Previous post was at 10:49 PM ----------
Gkeplar said:
I'm working on reading this thread now trying to follow there instructions, https://forum.xda-developers.com/galaxy-s8/help/s8-g950u-hardbrick-t3668572
Click to expand...
Click to collapse
Unless you are on revision 2 bootloader that is no use to you
You are not in edl mode. You are stuck in upload. The only way to get to edl mode is disassemble the device flip the motherboard upside down while hooked up. Ground out a test pin on the mother board while connecting the usb cable.