Related
Hi,
I recently dropped my i9023 and smashed the glass.
Bought a new screen with digitizer from global direct parts (www globaldirectparts com/Samsung-GT-I9023-LCD-and-Digitizer-Assembly-p/smsng6102150.htm)
Having put the new screen in it boots up fine and displays perfectly but the touch screen is not working at all and I can't do anything. If I put my smashed screen back in touch input works fine.
I've flashed back to stock I9023XXKB3 and I9023XXKB1 firmware, but nothing seems to help.
The ribbon to the screen doesn't appear to be damaged and because global direct parts had a minimum purchase of 2 I have 2 new ones and they are both unresponsive.
Anyone have any ideas?
My first idea would be to have the manufacturer fix it.
Sorry you are having trouble getting the touch screen to respond. I too have cracked my screen and would be very interested in your strip down and replacement steps as I am going to be doing the same. If you get time, could you write down your steps. There is a pretty good teardown at
http://www.ifixit.com/Teardown/Nexus-S-Teardown/4365/1
but I am not confident of the last bit of using a heat gun to separate the screen from the frame. Did yours come off easy ?
Yes I could have sent it to an authorized repairer but I would of been without the phone for a a while and it would cost twice as much. Plus I like pulling things apart.
markread544 - I pretty much followed the ifixit guide. however when pulling out the motherboard make sure the front and rear cameras and speaker are loose as well otherwise it wont come out.
I didn't use a heat gun, I just applied pressure until it started to lift, it would of definitely been easier if it had been warmed up but I didn't want to use a heat gun either. You would want to use an adjustable heat one on low if you did, I think a hair dryer would work as well.
I pulled mine a bit further apart then they did, the grey part in the attached pic comes off as well which makes it easier to get the screen out of the front bezel which it is also glued to.
Phone is back together at the moment with the cracked screen but I'll take some photos if I pull it apart again.
same problem here.
i bought an lcd on ebay for i9023 (slcd)
display OK , but no tactil response.
i had MP the OP but still no answer.
if you have any suggestion
thanks
how much for the screen? seems that 9023 is cheaper than 9020
80 euros for the less expensive , about 120-150 for the others
I ended up returning the screens from global direct parts and after about a month they gave me a refund.
After being quoted AU $250to get the screen replaced by an authorized repairer I decided to try again and bought a replacement screen on eBay from a seller called stream_beautiful for $86.
Got it today, installed and it works perfectly. No idea why the original screens from global direct didn't work.
I'm sorry to bump such an old thread, but I was wondering if there was any more information on this issue... I ordered an i9023 screen to repair a friend's phone about 2 months ago and had the same issue as the OP with it; touch input didn't work. I then contacted the seller (forceviewer on aliexpress) and he told me he'd replace it. After sending it back I then had to contact him again and send him pictures of the back of the old screen (with which touch input still works) because according to him there are 2 versions. Now I received the second screen a week ago and lo and behold, it exhibited the same problems. I noticed a number on the back of the screen is different, and the atmel IC (which I assume handles the digitizer input) has a different number on it too, however the seller has now adopted the position that it is definitely the correct display (quote: "If the pictures is right
The item will be right
I just send you the one same with your picturs
There are only two version.
Thanks")
Can anyone shed some light on what causes this? I know the guy's company tests their displays before sending them out, so that's probably not the problem, and receiving 2 faulty units in a row would be a bit weird, so I guess there's actually multiple versions (with a different digitizer controller IC?) which aren't compatible with each other... How do I make sure I'm getting the right one for my friend's phone? And, optionally, how would I go about convincing the seller to take this one back too and send me one that really works?
I'm having exactly the same issue...two replacement screens and touch input non responsive, re-install original and hey presto no problem...what I have noticed is that the part number on what I assume is the digitizer is different...
original -> KJ00423-101228-P00-7F-1
replacement -> KJ00423-101228-P00-5F-1
Yeah, my replacement says 6F-1 at the end, I can't check the original right now because my friend has his phone, but I'm willing to bet it doesn't say the same. Maybe I can make my case with this with the vendor, I'd really hate to have to buy another one of these displays for nothing
Guys,
It's the third SLCD screen that one of my fried is replacing to my I9023 Nexus S, and none of them is working. Yesterday he told me that when he bough the third one, the seller told him to "reprogram" the phone, because the drivers for new SLCD will be installed only then.
To be honest I didn't quite understood him, so, I though that the seller means to flash with a ROM. I did that, I installed CyanogenMod 9, everything went fine, but the touch still not working .
Does anyone knows how the phone could be completely wiped. Meaning everything what is in it to be reinstalled from the beginning....
I don't know what else to do, besides to buy a new phone
Hi All,
Just want to ask if anyone came to the solution yet ...?
Cheers,
no touch
Hello
i have the same problem:
1. The display works
2. But no touch reaction
i had bought a new screen for my I 9023 .
thanks for solutions
Yep, I have the same problem.
Original: KJ00423-101216-P00-1F-1
Replacement: (Not responding to touch): KJ00423-110207-P00-1F1
eBay Seller: mike410512
Bump - anyone sort this issue out?
I know this is an old thread, but since I have a shattered SLCD screen and i'm willing to replace it, i'd like to know what to do in case there's no touch response...
To get touch input again
Hi all,
I have smashed my phone screen twice on my S3 i9300. The first time I had the issue with the touch screen not detecting input but displaying correctly, I had taken it to an authorised repair centre and initially they did not know what was wrong.
There is only one way to "fix" this situation. You must remove the custom recovery and then reflash your phone with the stock samsung rom. Flashing the stock rom with stock recovery should pose no problem as it will be "official" and thus not blocked by stock recovery.
After reflashing, you must do a factory wipe + data reset. This is where you change your screen, making sure not to boot the phone for "the first time". If it does not work, repeat the reflash + factory wipe and try again.
The samsung rom will register the new hardware profile, and touch input will work. Why it works this way is beyond me, but taking these steps when changing the screen on a custom rom will ensure that the touch input works. Perhaps custom roms "borrow" drivers left over from stock rom? I don't know.
You can back up your current rom and restore after messing around with the samsung stock rom and you have gotten your touch screen working properly.
I have tried a whole heap of different "solutions" with this problem and this is the only one that works, and if you are taking it to a repair centre, make them aware that you have a custom rom installed.
Change screen
sinphild said:
Hi all,
I have smashed my phone screen twice on my S3 i9300. The first time I had the issue with the touch screen not detecting input but displaying correctly, I had taken it to an authorised repair centre and initially they did not know what was wrong.
There is only one way to "fix" this situation. You must remove the custom recovery and then reflash your phone with the stock samsung rom. Flashing the stock rom with stock recovery should pose no problem as it will be "official" and thus not blocked by stock recovery.
After reflashing, you must do a factory wipe + data reset. This is where you change your screen, making sure not to boot the phone for "the first time". If it does not work, repeat the reflash + factory wipe and try again.
The samsung rom will register the new hardware profile, and touch input will work. Why it works this way is beyond me, but taking these steps when changing the screen on a custom rom will ensure that the touch input works. Perhaps custom roms "borrow" drivers left over from stock rom? I don't know.
You can back up your current rom and restore after messing around with the samsung stock rom and you have gotten your touch screen working properly.
I have tried a whole heap of different "solutions" with this problem and this is the only one that works, and if you are taking it to a repair centre, make them aware that you have a custom rom installed.
Click to expand...
Click to collapse
Did anybody else use this way?
spanusorin2005 said:
Did anybody else use this way?
Click to expand...
Click to collapse
UP ..
i'm going to buy a screen + digitizer and i would have some advice about this, what code should i look ??? there are only two kind of screen or more ? what should i ask to the seller ???
hi people,
I have an asus tf300tg, unfortunately i've broke the touch screen. the version is the 5158n FPC-1 which is otherwise known as white label. I bought the new touch screen with the same code but it doesn't works.
I tried to do the restore factory setting with the power + volume down buttons, but nothing happened.
can someone tell me why? There is a thread that can help me?
I'm not expert so I would need a step by step guide.
thanks in advance to all who help me.
valex245 said:
hi people,
I have an asus tf300tg, unfortunately i've broke the touch screen. the version is the 5158n FPC-1 which is otherwise known as white label. I bought the new touch screen with the same code but it doesn't works.
I tried to do the restore factory setting with the power + volume down buttons, but nothing happened.
can someone tell me why? There is a thread that can help me?
I'm not expert so I would need a step by step guide.
thanks in advance to all who help me.
Click to expand...
Click to collapse
Have you found a solution yet? If you haven't go to this thread fro remedies. Again, spending more money on a 5158n is totally unnecessary; could have wasted it on beer instead.:
graphdarnell said:
Have you found a solution yet? If you haven't go to this thread fro remedies. Again, spending more money on a 5158n is totally unnecessary; could have wasted it on beer instead.:
Click to expand...
Click to collapse
hi,
thanks for the reply :highfive:
not yet, :crying:
that thread has "only" 65 pages...:crying:
i also tried the g01, but it doesn't works ...
for the 5158n version I did not spend much, just $ 50 (like a g01)
now i bought a keyboard hope i will receive soon.
valex245 said:
hi,
thanks for the reply :highfive:
not yet, :crying:
that thread has "only" 65 pages...:crying:
i also tried the g01, but it doesn't works ...
for the 5158n version I did not spend much, just $ 50 (like a g01)
now i bought a keyboard hope i will receive soon.
Click to expand...
Click to collapse
You don't need a keyboard to reflash the touch firmware unless you need to tick USB debugging. You can do that with a 10 dollar usb adapter and a regular mouse instead. But you do need to check your hardware. Scan pages 11-14 about the coil. If it's burned, no touchscreen will work.
graphdarnell said:
You don't need a keyboard to reflash the touch firmware unless you need to tick USB debugging. You can do that with a 10 dollar usb adapter and a regular mouse instead. But you do need to check your hardware. Scan pages 11-14 about the coil. If it's burned, no touchscreen will work.
Click to expand...
Click to collapse
hi,
i don't have good news, when arrived the keyboard i've updated the OS but the touch still doesn't works, then i thought that was burned the coil and i've ordered a new one, i installed it but the touch still doesn't works.
in the settings, the version of the touch screen panel is now: ELAN-0000-0000.
I tried to update to the new OS, but it's still ELAN-0000-0000.
anyone has any suggestions before I decide to throw him against the wall?
thanks
valex245 said:
hi,
i don't have good news, when arrived the keyboard i've updated the OS but the touch still doesn't works, then i thought that was burned the coil and i've ordered a new one, i installed it but the touch still doesn't works.
in the settings, the version of the touch screen panel is now: ELAN-0000-0000.
I tried to update to the new OS, but it's still ELAN-0000-0000.
anyone has any suggestions before I decide to throw him against the wall?
thanks
Click to expand...
Click to collapse
The burned coil, if it's burned, is located on the motherboard next to the ts board connector (flat silver cable), not the ts board itself. What new one did you order?
graphdarnell said:
The burned coil, if it's burned, is located on the motherboard next to the ts board connector (flat silver cable), not the ts board itself. What new one did you order?
Click to expand...
Click to collapse
hi, thanks for your help
i ordered this one:
90R-OK0JTP10000W TF300TG TOUCHPAD_BD./AS
already installed but it doesn't works....
valex245 said:
hi, thanks for your help
i ordered this one:
90R-OK0JTP10000W TF300TG TOUCHPAD_BD./AS
already installed but it doesn't works....
Click to expand...
Click to collapse
Look at the enclosed thumb and try to locate the same coil on your motherboard to see if it's burned or not. If it is, a new TS board won't help.
Hello!
I own a TF 300T wich was bought a year and a half ago. A year ago the display appeared broken and since today I didn't did a further investigation on "what is broken".
I have tried using the search option, didn't find my problem there.
The screen is cracked (or I think), it seems to turn on but I can only see some white light and the crack itself.
The touch screen is in perfect state (or it seems to) but since I can't see anything I don't know how to check if it works, I touch everything and there is no hepatic response.
I tryed to use [email protected] but my device is not recognized but I can acces the internal storage from windows (7), may be usb debugg is not ticked =S
The tablet is not rooted and the bootloader is not unlocked.
All I wan't to know is if the touch is working for only buy the LCD display on ebay, since I can't buy at this moment the touch digitizer (I have to pay 85% of taxes that my country, Argentina, wants to take from me).
I don't know if connectin the mini HDMI to an HDMI capable monitor/tv will help me since I don't own the needed cable (and maybe these is the best way).
Maybe there is a way to cast the tablet screen by some other way.
I just want to know your opinion to avoid throwing money away for something that wont work.
Thanks a lot and kind regards.
nehuy said:
Hello!
I own a TF 300T wich was bought a year and a half ago. A year ago the display appeared broken and since today I didn't did a further investigation on "what is broken".
I have tried using the search option, didn't find my problem there.
The screen is cracked (or I think), it seems to turn on but I can only see some white light and the crack itself.
The touch screen is in perfect state (or it seems to) but since I can't see anything I don't know how to check if it works, I touch everything and there is no hepatic response.
I tryed to use [email protected] but my device is not recognized but I can acces the internal storage from windows (7), may be usb debugg is not ticked =S
The tablet is not rooted and the bootloader is not unlocked.
All I wan't to know is if the touch is working for only buy the LCD display on ebay, since I can't buy at this moment the touch digitizer (I have to pay 85% of taxes that my country, Argentina, wants to take from me).
I don't know if connectin the mini HDMI to an HDMI capable monitor/tv will help me since I don't own the needed cable (and maybe these is the best way).
Maybe there is a way to cast the tablet screen by some other way.
I just want to know your opinion to avoid throwing money away for something that wont work.
Thanks a lot and kind regards.
Click to expand...
Click to collapse
You could try a VNC app to view on the computer you srcreen via WiFi, but idk how you will open it and set it up.. The HDMI is a good idea, and the cable is only a few dollars , but I would suggest just replacing the digitizer or buying a new tablet. :crying:
cmendonc2 said:
You could try a VNC app to view on the computer you srcreen via WiFi, but idk how you will open it and set it up.. The HDMI is a good idea, and the cable is only a few dollars , but I would suggest just replacing the digitizer or buying a new tablet. :crying:
Click to expand...
Click to collapse
Yes, thanks for reply.
A friend borow me the HDMI cable, now I see that only the display is broken and the touch is working gorgeous!
Now going to try to buy one for 50-60dls and hope it works!
nehuy said:
Yes, thanks for reply.
A friend borow me the HDMI cable, now I see that only the display is broken and the touch is working gorgeous!
Now going to try to buy one for 50-60dls and hope it works!
Click to expand...
Click to collapse
Good luck. There are several guides to dissembling the tf300t around xda and replacing the screen or digitizer.
Hello,
I have searched the threads but cannot find a situation similar to mine so am posting, but apologise in advance if this has been solved before. It's a bit of a long story. About a year ago I was foolish enough to have stood on my TF300T, cracking the screen. The tablet was still working, but it would not register touch. I put it to one side and left the battery to drain. For various reasons I have just got around to replacing the screen.
I found a screen and digitiser of the correct version for my UK TF300T (version G01) and I'd thought the replacement went without any problems, although I was slightly unsure of one digitiser connection. On pressing the power button (I had pre-charged the battery) the screen came to life just as I'd left it as if coming out of sleep rather than being off for a year. It was short lived though and soon the tablet went to black and would not turn on. I thought maybe it was the digitiser connection so went back in to re-fit it. It was only then that I noticed the power switch on the logic board itself under the plastic shell. I hadn't switched it to off before (duh) so did so then, refitted the digitiser cable much more securely,switched the power back on and tried to boot, but nothing happened at all, apart from the power LED flashing orange. After some experimenting (trying to charge the tablet again etc) I found I could only boot by charging the dock and plugging the tab in the dock, but the tablet would only get as far the ASUS screen (not the 3D one, just the flat lettering), with the 'device is unlocked' message in the top left corner and stops there. I can turn it off, but can't boot into recovery at all. And that's where I am now.
Things I have tried - a different logic board from a TF300T's scrounged from eBay which also had a cracked screen (this, weirdly, seemed to have the same problem as mine), swapping various parts out from some other TF300T's (without logic boards) from eBay and contacting the device through Sandix's ADB GUI (after downloading and extracting the SDK), which registered no device.
My best guess at what's happened is that the battery on the tab itself is totally gone (as are the three other batteries I have accumulated) after a last valiant effort and either that going or me messing with the on off switch has some how corrupted the boot process. Is that possible? What do people think? I could buy a brand new logic board, but the only ones I seem to be able to find have some different brand chips on them and appear to be different versions - versions probably not compatible with my digitiser. :S
I am quite a novice here (and maybe poking around the inside of my tab wasn't a great idea, but then neither is wearing boots in the house) so any help would be greatly appreciated! Sorry for the long post, but I wanted to give a detailed report. Let me know if you have any questions. Although unlocked, it is running the stock ROM.
I would make sure drivers are reinstalled properly, by removing the drivers, reboot the computer, reinstall the drivers and then reboot again.
See if that works.
I had something similar happen on a different tablet. That was one from Box.co.uk, but after trying to get it fixed under warranty (and missing the end date by 1 day), I opened it myself. When the charger was plugged in, it showed the charging LED, but it didn't actually charge it.
I don't suppose you've checked the terminals for the battery to the mainboard? On this other tablet, one had broken off. I re-soldered it on, charged it fully and it worked fine.
This is now my 3rd attempt to find a solution to my problem. My first attempt went unanswered, and although my last attempt got a response, it didn't help me one bit. Unfortunately, I didn't gt a response to my folow up questions either. So, this is going to be a much shorter explanation of my issue. (Previous post has a detailed explanation).
I bought a LG K20 Plus brand new in May. I broke the screen and decided to just buy the same phone and put my logic board into. The problem is, when I did that, the digitizer fails to recognize any touches. Strangely, the digitizer, again, works while booted into TWRP recovery but fails again after normal reboot. I'm so frustrated. I got really excited when my previous post got a response. It was such a huge disappointment to realize that I wasn't going to get the help that would lead to fixing my phone. After over a month and, at this point, my hope was non existent, I decided to just seperate the glass from the lcd and then put the glass on my broken phone. But in looking at it again, I don't see what difference the display makes. I really dont want to risk breaking another didplay. I don't know, it's apparent that I just don't get it. So, here i am again, asking for help. Will someone please tell me what I'm missing. Also, if you have advice please list more then a one sentence solution. I'll need some direction.
NOTE: I'm currently using a mouse via OTG cable and cannot change USB connection from "charge only" to mtp. So connecting to a PC isn't possible for more then charging.
Boot into fastboot and unlock the bootloader. Probably won't help, but why the hell not, right?
Sent from my [device_name] using XDA-Developers Legacy app