[Q] Back to Stock - AT&T, Rogers HTC One X, Telstra One XL

Please forgive me, as I have not searched the forum extensively for an answer, but I'm in a bit of a time crunch as I am leaving on a trip tonight and need to get back to some semblance of a working phone.
Some time ago I flashed some rom (I think Paranoid Android; I don't remember. I liked it enough to keep it, then I didn't worry about it again after that.) Little by little it started getting slower and buggier, but for the most part it worked fine, so I ignored it. For the last couple of weeks it started losing signal and data constantly, with no change to the phone. I kind of just lived with it because I could usually restart my phone and I would regain signal, but as of a couple of days ago, it would just drop off and not come back until it wants to.
I had the day off to prepare for my trip, so I decided I would try to go back to stock; there's almost nothing that I do that requires a custom ROM and I had no data issues on stock, nor does my wife on her Note. I looked around for a bit for instructions to restore my phone, and found some, but out of the handful of pages I went to, each one had at least one link that was dead, rendering the method useless, to me, a layman, at least.
I then decided I would just find a Stock Rom, thinking that might be the next best thing. I found Clean Rom on here and decided to try to flash that. I made a backup of my system, wiped everything, and then flashed it. Except something is wrong with the zip and keeps giving me an error message. I then tried to restore my back up that I had just made to try something else, but something happened to that, and it also wouldn't open. I tried the backup before then (quite old, as I haven't done any tinkering with my phone for quite some time) and it worked, but it tells me that my sim card is disconnected, so I have no data or signal. As it is an old restore, I'm not sure what the name of the ROM is, but I can provide all of the information needed, if someone needs that to figure it out.
Anyway, long story slightly shorter: I need to fix this today, and like as soon as possible. I will give ten dollars, count them TEN DOLLARS, to the first person who can provide a set of working links and very straightforward instructions as to how to get back to stock (or if there is a good working ROM that will give me FULL functionality with no flares that would be easier to do. Easy and fast are the key components to this request). I'm not dumb, but I am no longer immersed in the lingo of this community, as it has been a few phones back that I really cared about actually experimenting much with my phone, so non-technical language would be nice. I know what flashing and wiping means. Most of the rest, probably assume I don't.
Thanks.

Your best (easiest) option is probably to flash another stock ROM, or stock-ish ROM. There are quite a few options in the Android Development section. There are a couple of stock rooted at&t ROMs in the first couple pages, also a stock rooted Telstra ROM.
You didn't mention which carrier you're with, whether your phone is branded, or any of your important details, like your firmware/hboot details and whether you're s-on or not. If you wanted to go back to completely stock, I'd need to know those details. Going completely stock can/will be a longer process though.
Sent from my Evita

Okay, I'll try another one. I'm not sure why Clean Rom didn't work, but if another one or two don't work I'll come back here and I'll have you talk me through getting back to stock and I'll throw you a digital Hamilton.
Thanks.

Well, I tried another couple of ROMs. They installed correctly, but it says that I have no sim card, so I still have no signal. Maybe I some how deleted my radio when I did a system wipe while trying to install one of the ROMs? I'm not sure.
Anyway, for "more details" I'm on AT&T, I'm not sure what you mean by branded, but it's the HTC One X, the current ROM is 4.1.1. I haven't done S-On/S-Off, or anything like that other than unlocking the bootloader a long time ago. The kernel version says 304010-g240d4d5, the baseban version is 0.17.32.09.12_10.86.32.08L The Build number is 3.17.707.1 CL134054 release-keys.
I'm not sure which of that information is relevant or not, but that's everything I can tell you.

Never mind that last post. When I said in the first post that I'm not dumb, apparently I lied. My phone fell off a table this morning, and I guess it knocked the sim card loose, but it coincided with doing the factory reset stuff, so I thought they were connected. I pushed it back in, restarted, and now the stock ROM I'm using works great.
Thanks/Sorry!

Well, it turned out to be an easy solution (Occam's Razor FTW yet again).
But this thread made me think . . . why the heck does it seem so many people lately flash ROMs without doing a nandroid first? Its a no brainer to me. If you are trying new ROMs, and not sure how they will perform, why would you not give yourself an easy way to simply revert to your last known good config?

I couldn't agree more, but there's plenty of not-so-smart practices on here, so I'm not at all surprised.
Sent from my Evita

Yea. Nandroid ftw
Sent from my HTC One using Tapatalk 2

Related

[Q] I need help.

Today, I acquired a infuse 4g, off contract. I wanted to mess around with android, as my current phone is an iphone, and maybe switch over.
One of the first things I tried to do was tether my iphone to my infuse using mywi. I soon discovered android doesn't work with ad hoc networks. I googled a couple fixes, and decided to try my hand. I have never touched android before. I found this thing that said I could. So I went for it. After reading a few guides, I decided the first step was to root it using superoneclick. That went fine. Then, I read the instructions and it told me to 'flash the zip file using a recovery rom' which was total gibberish to me. So I did some more googling and found a modified 3e recovery thing for the infuse. I used some file system app to put that where it was supposed to be, but then saw that I needed clockworkmod to be able to flash things. By this point I realized I was far, far over my head, but stupidly pressed on. At about the same time, I also extracted the zip file from exop.pro, and replaced the wpa file that existed already in system/bin with the one from the zip. I also booted into recovery mode, and tried to install clockwork mod, which failed even though as far as I can see. Now, when I turn my phone on, everything is ok except that it can't scan for wifi. I assume this is because I ****ed with the wifi file. I've basically decided to give up at this point, so please, just tell me how to made it work again and I'll promise to not **** with it anymore. Also, I neglected to make a backup. Stupid, but I didn't know how and didn't want to go through another huge thing.
tl;dr
I tried to make it so I could connect to ad hoc networks on my infuse 4g and ended up destroying my wda_supplicant file in system/bin (i think) and
Google the original file you replaced, ' wpa supplicant file download for infuse 4g'. Next time save a copy or backup of whatever your doing.
Thanks, but I really have no idea what is what. Could you link me the right one? I'm sorry that I'm so useless.
Itaer said:
Thanks, but I really have no idea what is what. Could you link me the right one? I'm sorry that I'm so useless.
Click to expand...
Click to collapse
this was your problem the first time... you need to read and study before you just start flashing things to your phone man. haha... us linking you somewhere will not help you figure that part out... and its an important part of tinkering with these phones in the way you are trying to.
rid yourself of the apple mentality where everything is spoon fed.
moving on, however, do what the guy previous to me said... find that file you downloaded. and do some reading, watch some instructional videos, focus on just rooting the phone properly for now. do that, then read, watch, ask questions like you are doing when you need to, then proceed.
read comments and stuff in forums about the ROMs you are flashing, what kind of problems do they have, what recovery is recommended for that particular ROM, stuff like that. just READ everything and anything you can about what you are doing....
the company that made your newly found OS has a nice little search engine called google... and it works pretty well if you know how to use it i'll keep an eye on this thread for you as others are probably doing so we can provide you with whatever answers you might need. good luck!
a good rule of thumb when flashing hax0red software to these phones is when something ****s up, 9/10 times it's just a little tiny thing you missed or did during the install yourself... so back to square one, and pay close attention to detail. these phones can be a little touchy when flashing ROMs if you are not doing it exactly they way it is recommended.
perfect example of this: when i had my samsung moment... when i converted from 2.1 OS to 2.2... for some odd reason i would ALWAYS have to flash a little script zip to wipe the 2.1 data from the device before flashing the 2.2 zipped ROM to the phone... the 2.2 ROM was supposed to do this and take care of it completely for me, but even though it did, the only way it would work properly every time i was going from 2.1 to 2.2 was to flash that zip beforehand...
hope that long rant provided some useful insight
Thanks.
But I have read the instructions on the stuff I'm trying to do, several times, and like I said, I'm more confused that I was at first.
I'm just not willing to break it any further.
So basically what I'm wondering now is, how do I put everything back to how it should be. Is there a way? Like, is there a way to load the original software back? I don't think restoring it to factory settings would fix what I did, but tell me if I'm wrong.
I just want everything back to normal.
Please.
Edit: I know it seems like I'm not doing anything to help myself, but I have a lot on my plate in life right now, and I also have absolutely no idea where to even start. Half of the terms you use mean nothing to me, and I'm just so overwhelmed.
I just want to know if there is some way to put it back to how it came out of the box.
Turns out that once the new wda_supplicant thing is ACTUALLY GRANTED PERMISSION TO EXECUTE, that everything works fine. Thanks guys
see... Knew you would figure it out man
Sent from my EVO3D using XDA App

Two very annoying issues with this phone

Rooted, CM 7.1.0, T-Mobile
Not sure if these are CM issues or HTC's crappy hardware issues, but...
1. When I try to turn on the screen using either the top button or bottom trackpad button, the screen will flash on for a second and then go off again. It will do this two or three times until the screen stays on at the lock screen. Didn't do this before CM, but also didn't start until months after I modded to CM.
2. When using the on screen keyboard(in vertical mode) sometimes it's like the touchscreen is responding very slowly to my taps and CERTAIN KEYS will not work at all. So I'll be typing and the keyboard will be kinda sluggish and suddenly I'll notice that none of the a's I'm hitting are registering. I'll hit the area of the screen over the "a" key and the surrounding keys will register but not "a". I will usually have to turn the screen off and then back on before it starts working again. I think it did this the first time before I modded, but can't quite remember.
Anyone else having these problems?
The first problem has happened before on some roms.
I don't recommend using CM 7, its old, outdated and hasn't been fully patched.
I had that same touch keyboard issue with my HTC EVO shift and my HTC Inspire....an of course all my phones were on different ROMS
Sent from my myTouch_4G_Slide using Tapatalk 2 Beta-4
The first issue... are you oc? If so how much? Really no need to oc this phone. Also, it could be a wake issue, if you are underclocked to much, there is a minimum amount that sometimes has to be higher on some phones than others.
It seems to me these could be kernel issues.
Sent from my HTC Vision using xda premium
mrbmg said:
The first issue... are you oc? If so how much? Really no need to oc this phone. Also, it could be a wake issue, if you are underclocked to much, there is a minimum amount that sometimes has to be higher on some phones than others.
It seems to me these could be kernel issues.
Sent from my HTC Vision using xda premium
Click to expand...
Click to collapse
Unless CM over or under clocks by default, then no changes in cpu.
You should run the HTC stock software for a few days or a week to see if the problems you have are persistant across ROMs, or something specific to your current software package.
Just a thought.
Sent from my Bulletproof_Doubleshot using xda premium
Blue6IX said:
You should run the HTC stock software for a few days or a week to see if the problems you have are persistant across ROMs, or something specific to your current software package.
Just a thought.
Sent from my Bulletproof_Doubleshot using xda premium
Click to expand...
Click to collapse
Yeah I've thought about doing that, but I also use my phone for business and switching between roms is kinda disruptive, so I haven't done that yet. Hoping for more feedback from others.
Preparing for backup
Return to Contents Page - doubleshot Developers Reference
Backup Guide
AviatorJud said:
Yeah I've thought about doing that, but I also use my phone for business and switching between roms is kinda disruptive, so I haven't done that yet. Hoping for more feedback from others.
Click to expand...
Click to collapse
Yea, that is something that impacts us all. I could get a lot more dev done if I didn't have to have my plan phone set and ready a specific way each shift to be able to do my job the way i'm expected to.
Best bet would be to wait until you had a day or two off, maybe a weekend or something and when you finish with your obligations before that free time starts:
-try to have near to a full battery or a full one waiting.
Installing a new ROM always works better with a full battery on install, so if you can already be at that step you can start right away instead of waiting for it.
-Make a clockworkmod backup of your device as it sits, and copy that backup to a computer somewhere.
-Get all the ROM files you need to re-install it in a folder with that clockworkmod backup you just made. When you go to put the phone back together to go back to work, if the backup doesn't work for some reason you can at least install fresh and go from there.
-On that note, backup all your apps too. If you do end up having to re-install your ROM you are running right now, being able to install all the apps right away again off the sdcard saves a lot of time and hassle.
Make sure to get those apps backed up to a computer too.
-backup all your contacts. Export everything you can to the sdcard, and then copy that to the computer too.
-Make sure you have all the passwords and account names you need for anything you have installed. (Gmail(s) - Games - accounts tied to apps or services you use)
If you do have to reinstall everything, and you use internet services like dropbox or an internet faxing service you don't want to have to track down those logins if you don't type them often. Make sure you check all your apps and write them down ahead of time.
-Lastly, since you are on CM7, use titanium backup to backup everything and copy that also to the folder on the computer. The word backup in the computer industry is synonymous with redundant, and if it's not you're doing it wrong.
The reason why I said to copy all these backups off the phone and onto a computer is because if something catastrophically bad happens to the phone then what?
By catastrophically bad I mean you format the sdcard by mistake on a factory reset while you're playing with different ROMs - what then?
If you do need the device for work, and you are serious about trying to test the errors against being a phone-specific hardware issue or a software issue with the ROM you are using, then jogging your process by putting this all out there might help you get started.
When you get that downtime, you'll know ahead of time so you can prepare, and then when it hits you have an immediate plan of action to put into place to maximise the time you get for testing.
Also, have the ROM you want to put on it ready to go, and if possible alternates to that - so research the 3 software versions available from HTC for the device.
Also become familiar with this process:
Restore to stock
...maybe download all 3 software versions before your free time hits so you have them already. If everything goes sideways you can always use one of them to restore the device.
If you are S-OFF you have nothing to worry about for doing any of the software updates unless you manually re-lock the device, so just don't do that and you'll be fine.
If you are S-ON speak up and i'll lay out your possible headaches along the way and what we know about them if someone else doesn't first.
If you have prepped before the free time hits:
1 - passwords/account info written down and at the computer you'll be using...
2 - all software packages (restore files, roms, anything else...) that you need downloaded and on the computer you'll be using...
3 - all the apps you use backed up and on the computer you'll be using...
4 - any media like pictures and music or anything else backed up to the computer you'll be using...
5 - a full battery or close to ...
...you are still looking at almost an hours worth of backup time to do the clockworkmod backup, titanium backup, transfer them to the computer, and then you might run a little over that time when you test the clockworkmod backup.
( you always test the backup - the only thing worse then not having a backup is having a corrupt one you thought was good )
...which cuts into your time testing the other ROM enough as it is, but if you aren't ready to do it like this it will take significantly longer.
Since you'll know when the time hits getting a majority of the media, pictures and user generated stuff plus most (if not all) of the apps you use backup up the day before helps cut down on a lot, but that hour is still lost to making a way of putting it back together again.
You also need to leave yourself a solid 4 hours to put the machine back to the way it is before you started on the other side. Again, on install, you want to have a full battery so plan for that too.
4 hours gives you enough time to get everything slapped together from a fresh CM7 install and manually doing all your apps and setting up the phone for work, if the CWM backup fails for some reason and you have to start over.
I just want to see everyone have their phones running right, and if it's a hardware issue then you should get it repaired, if it's a software issue then you should seek a solution - but the quickest way to a result, and the one for your issue, is to directly test it yourself.
Since you sounded like you came to that conclusion too, your only issue now is squeezing it into a time slot you can get so don't hesitate if you have questions on the processes involved.
Edit - also:
If you have multiple MicroSD cards you could use for this, then you can save a lot more time.
You could take the one you have in there now out, and put it to the side so that when you installed your work setup again the memory card and all it's stuff is right there.
Then you could take different memory cards and have them pre-made to what you need, so as soon as you are done backups you power off and swap memory cards.
First one you swap in has the PG59IMG.zip restore file (and nothing else) renamed that way and ready to go, so when you power back on to hboot that installs itself and you save the time spent copying that over before you can install it.
When that finishes, you are back to stock and ready to go, and you didn't change any of the info on your work sdcard.
Something to think about, if work stuff is that important that's what i'd do (and what I do myself, so thought to add it)
Wow Blue, thank you for taking the time to respond. I think I will have some time this weekend to give this a shot. I am S-OFF. And you're right, as long as you plan everything ahead and allow for the time to get set back up, it's not too bad. I'm just trying to decide what rom to try switch to. I really hate sense, so I don't really wanna go back to stock. Wish there was a good stable vanilla to use. Any thoughts?
Oh and if I want to update to the newest radio, which is listed in your "return to stock" thread and then perhaps use another custom rom, like bulletproof, will that radio stick? Do roms not ever update the radio? I just noticed that I am on the original one for the doubleshot, which came out last june.
AviatorJud said:
Oh and if I want to update to the newest radio, which is listed in your "return to stock" thread and then perhaps use another custom rom, like bulletproof, will that radio stick? Do roms not ever update the radio? I just noticed that I am on the original one for the doubleshot, which came out last june.
Click to expand...
Click to collapse
I don't even know what radio I'm on that's a sad thing...but yeah once you update your radio, no Rom will overwrite the radio unless it somehow has one in it you know...
Sent from my myTouch_4G_Slide using Tapatalk
AviatorJud said:
Wow Blue, thank you for taking the time to respond. I think I will have some time this weekend to give this a shot. I am S-OFF. And you're right, as long as you plan everything ahead and allow for the time to get set back up, it's not too bad. I'm just trying to decide what rom to try switch to. I really hate sense, so I don't really wanna go back to stock. Wish there was a good stable vanilla to use. Any thoughts?
Click to expand...
Click to collapse
My pleasure, it's what makes XDA work - people taking time to share what they've learned so others can benefit from or add to the knowledge.
If you are trying to bug-check, honestly, the stock official ROM is a good one to use. It's not something you are so much doing to enjoy the phone, as much as to check on a specific aspect of it.
Further, you are already halfway home on putting the phone back to factory settings if it is a hardware issue, so then you just have to S-ON it and send it in for repair - though you probably won't get it back with S-OFF ability, you will at least be able to unlock it.
Just from directly developing things for the device, and having to go through these testing procedures time and again, I try to set the process up to keep moving, so by going to bone stock if it is broken you already have taken steps to make it what it has to be to send it in, the next looming goal if you aren't going to restore to your work setup.
AviatorJud said:
Oh and if I want to update to the newest radio, which is listed in your "return to stock" thread and then perhaps use another custom rom, like bulletproof, will that radio stick? Do roms not ever update the radio? I just noticed that I am on the original one for the doubleshot, which came out last june.
Click to expand...
Click to collapse
This was just answered above me, but you can always go back to previous radio installs if you are S-OFF...but only if S-OFF.
I've run Bulletproof on the new radio and it runs fine, so doesn't matter either way on that one - other ROMs you'll have to ask the author.
ROMs can update the radio, or only work on specific ones, but for our device I don't think it's been an issue yet, pretty sure everything works with everything on that part.

Is my Samsung Infuse DEAD?

Hey, guys. Hoping some of you experts can help me diagnose what's wrong with my Samsung Infuse. I bought it off Craigslist at the end of May, and the guy had the phone with the original screen protector on it, with the original case and all accessories, so I had no reason to believe it had any problems. He told me the phone was already rooted & unlocked, which I wanted since I signed up with Straight Talk. I used it for June & July and had a host of problems, so I put on the CM10 ROM last week to see if it helped. It didn't. Here are the problems I continuously encounter:
1. When going to unlock my phone with a pattern, once in awhile it won't detect my finger-presses. Sometimes nothing shows up at all, sometimes one of the dots will highlight as I pass over it, but it won't draw. Eventually the screen turns off, and I turn it on and try it again. Usually it ends up working.
2. The battery dies much quicker than I expect it should. I tried running JuiceDefender and not running JuiceDefender, and it doesn't seem to make a difference. Even without using my phone much for anything, even with the screen off, the battery will run out before the day is out. It's like if you were driving and had a hole in your tire... seems like some sort of a leak.
3. The cell radio seems flaky. Sometimes I won't get texts on time. A lot of the time I can't access any data, which is very important as I use Google Voice for lots of my texting, so I send a text and it won't go out. Loading web pages or reloading my email shows that it is a data problem.
Those are the primary problems, and I suspect that somehow they are all related. I'm not sure if the Craigslist guy sold me a lemon, or there is some other problem that came up. I've tried multiple ROM's and disabling every app I can think of. Can anyone think of anything that would cause these problems & any way to fix it? Or do I just own a broke phone that I have to throw in the garbage?
Thanks in advance for reading!
a whole slew of problems can lead to a whole slew of possibilities for your issues.
first, i wasnt aware that you could do any of this on a straight talk phone, but i could be wrong. i am not the "expert" you may be looking or hoping for, though one i am sure will show up.
second, i think the response you may get is......did you go to JB straight from Gingerbread??? that will cause HUGE problems.
dd you read OP and follow to a tee??? again HUUUUGGEE problems.
the "never fail" here.....READ READ READ. feel confident as to what you are doing and follow steps one at a time. UNDERSTAND steps one at a time.
first thing that never hurts.....return to stock and start from scratch.
"super everything thread" under development.
Odin "stock-root & modded 3e rcovery.
follow all directions TO THE TTT.
if that doesnt work, you might have to get some mortar, you've got yourself a BRICK.
i know almost everyone else here is more of a expert than i am, but i do believe that is where they will tell you to start
good luck and be sure and thank the experts
captemo said:
first, i wasnt aware that you could do any of this on a straight talk phone, but i could be wrong. i am not the "expert" you may be looking or hoping for, though one i am sure will show up.
second, i think the response you may get is......did you go to JB straight from Gingerbread??? that will cause HUGE problems.
dd you read OP and follow to a tee??? again HUUUUGGEE problems.
first thing that never hurts.....return to stock and start from scratch.
"super everything thread" under development.
Odin "stock-root & modded 3e rcovery.
follow all directions TO THE TTT.
if that doesnt work, you might have to get some mortar, you've got yourself a BRICK.
Click to expand...
Click to collapse
While I have no idea what you're getting at by your Straight Talk comment, as ST is little more than AT&T service that's sold through a 3rd party at a discounted rate, the fact that he's using ST may be part of his problems, at least in regards to the network issues. I'm also having an unbelievable amount of data issues on ST. ST is having some network problems that are affecting a decent amount of customers who are on their AT&T network.
One thing that the OP may want to try is this: Download DNS Changer from the Play Store, and change your primary and secondary DNS to OpenDNS1 and OpenDNS2. Or try different settings, as there are a bunch that are available. That has made at least some difference with my data connectivity issues.
Based on my own experience, having tried to go to JB directly from GB, is that if it's going to affect your radio, it's likely to completely wipe out your EFS data so you won't have ANY cellular or data networking capabilities. As stated, that's simply based on how it worked out for me, and there could easily be other side-effects that just didn't happen to show up for me.
I agree with returning completely to stock UCLB3, with the GB bootloaders. Then flash Entropy's 4.4.2012 Kernel, which will also install CWM Recovery. I'd personally reccomend Heimdall, as it seems to be somewhat simpler. Detailed information on returning to stock via Heimdall can be found in this thread:
http://forum.xda-developers.com/showthread.php?t=1629079&highlight=heimdall+uclb3
If you use it, be sure to thank qkster for making it available. He's probably the most helpful person you're likely to find on this forum, especially where us noobs are concerned.
I would take it back to stock and start all over.
Here is a very helpful thread.
http://forum.xda-developers.com/showthread.php?t=1700416
I agree with parrot head. When issues arise go back to stock. That's the best part of our phones. They are damn near impossible to really mess up. Just have to be ware of bootloader flash going wrong. If you got your gb rom from keis your good to go though.
Sent from my SGH-I997 using xda app-developers app
Appreciate the response, guys. I guess it doesn't hurt to try to start from scratch... AGAIN! It just seems like I'm putting an awful lot of hours into putting new ROM's and bootloaders on this phone. Going to be especially frustrating if I go through all the steps and it still doesn't fix my issues, which would mean my phone is broke. Oh well, guess I have little other choice.
All of the issues sound related..
It shouldn't take long to drop to stock and flash up to JB.. I've bobbled and missed steps here and there and have had to return from stock more times than I care to admit.. even rooting and flashing up the ladder only take about 20 minutes if even that..
Good luck!
drnecropolis said:
All of the issues sound related..
It shouldn't take long to drop to stock and flash up to JB.. I've bobbled and missed steps here and there and have had to return from stock more times than I care to admit.. even rooting and flashing up the ladder only take about 20 minutes if even that..
Good luck!
Click to expand...
Click to collapse
Yes, the flashing process isn't that long, it's getting back my phone to all of my customized settings that ends up taking weeks. Home screen icon positioning, logging in to every app, system settings, etc.
Didn't create a backup?
drnecropolis said:
Didn't create a backup?
Click to expand...
Click to collapse
I've always created backups with Titanium Backup, but when I restore the apps, a lot of them ask me to re-login or re-verify myself.
Thanks for the advice guys.
Spent a whole day going back to stock, then CWM red, then ICS, then Jellybean. Things seem to be markedly better, but the phone still seems laggy in a few places. Is this just because it's not the latest and greatest processor?
Also, the GPS just does not work right. It's still identifying me as being in Missouri even though I'm in Nevada. Consistently. Do I just have to live with that?
veeRob said:
Thanks for the advice guys.
Spent a whole day going back to stock, then CWM red, then ICS, then Jellybean. Things seem to be markedly better, but the phone still seems laggy in a few places. Is this just because it's not the latest and greatest processor?
Also, the GPS just does not work right. It's still identifying me as being in Missouri even though I'm in Nevada. Consistently. Do I just have to live with that?
Click to expand...
Click to collapse
Are you still using the Trebuchet Launcher that comes built-in to the JB ROM? If so, that may be part of your lag problems. I just use ADW EX launcher. Here's an excerpt from the Paranoid Android JB OP:
******* EVERYONE: If you experience a sudden lag for no reason, IT is due to Trebuchet. GOOD NEWS though... From reading the log cat on my end, there is a very simple fix... Go to settings -Launcher - Homescreen - And Check "Resize any widget" and you are good to go! Instantly fixes the lag problem that a few have been experiencing. I have located the source code that needs to be changed and this will be enabled by default on future builds. ********
Click to expand...
Click to collapse
As far as the GPS goes, I think Samsung just used ****ty receivers in the Infuse. My GPS isn't quite as bad as yours seems to be, but it's nowhere near as accurate or reliable as the GPS chipset in my crummy little Optimus V.

My SK4G Story

Hi all,
I finally decided to add a custom rom to my SK4G. I had retired it for a year or so, not from getting a new phone, but rather my youngest child dropped it in a mud puddle. I had put it in rice and all that good stuff. I was able to get it to turn back on, but it has very very very low battery. So I put it on the charger, and it would briefly show the charging symbol and disappear. So I had assumed that it was totally shot, And while I was disappointed, because I love this phone, it still was not surprising. I mean it was in a mud puddle right. LoL
Well about 2 weeks ago I got bored, and figured what the smudge, I will ticker with it. I figured, I couldnt do any worse to it than what was already done. So I once again tried to see if it would charge. Tried by wall charger, by car charger, and by USB charging. But alas once again nothing. Well my husband also has a SK4G. So I ganked his battery for a little bit, and lo and behold, it worked. Turned on flawlessly, and not one issue in the operating system at all. Well at least as flawlessly as a stock SK4g could get. lol
So I was thinking maybe the charger slot had shorted out for whatever, from it being in the mud puddle. I put the battery from my SK4G in my husbands phone and agin tried all 3 charging methinds, and still nothing. So I pluged my phone in with his battery and it went to charing just fine. Okay so, new battery. Not that bad, but I dont order anything over the net. I hate waiting, I live in a big enough city, I figured I could go to one of the electronic stores and get one.
So I tried 5 different places, no one had a replacement for it, but once gain I was impatient and didnt want to wait. Did some googling and found out Batteries plus carries a replacement for it. Wasnt thrilled by the fact that they charge 2 to 3 times more for it that other places. But whatever, if it got my phone running again, okay. I had my oldest son pick me up one on his way home from work. Gave him the stock battery numbers and all that. He brings it home, and I go to put it in and..................It is not even close to being a compatible replacement for the samsung battery. Went back down there and returned it. Told the sales clerk that their website was completely wrong. Upon looking through their wall of replacement cell batteries, I did find another battery that was a perfect match. Only to have the "Battery Expert" argue with me about it being the right one. Finally got him to stop running his mouth and bought the battery.
I had just recently ended my contract with t-mobile, and wanted to take my SK4G with me to a new carrier. Well in order to do that, I needed to unlock the network. So it was research time. Googled and found XDA. Which from then on has ben invaluable to the process. Found Sidekick 4G Unlocking *Follow Directions Closely written by troby86 and SuperOneClick - Root/Unroot Your Samsung Sidekick 4G by Ayoteddy .Had a few problems with SOC. It kept freezing at step 7. Took me a few to find the reason why ( answer is in the forums here, just took some digging and reading to find. The culprit was the "Exploit setting needed to be set to "psneuter". Changed that and finshed rooting with out any more problems on that part.
Next had to unlock the network, following the above mentioned thread. Tried it 2 or 3 times to no avail. Then it dawned on me that I hadnt rebooted after I got it rooted. So rebooted and tried the terminal part of it again. And Bingo! It took the commands or whatever you would like to call them. SK4G was now unlocked. Yay!
SInce I had already been in the forum looking at the unlock and root guides. I decided why not go ahead and put a custom rom on it too. I loved my SK I just loathed the software on it. Constantly freezing while surfing the net or trying to use facebook. I spent a bunch of time browsing the forums, reading the comments on all the roms and trying to decide which rom I wanted to use. I had orginally choose CM6-Merged.
So read the thread on it, and even watched a youtube video by sinesolder. The next task was to chase down all the files I needed to install that, plus the CWM stuff too. I flashed CWM using the app "Root Manager" in the play store. Next was to swap out the "recovery" file. Took a few mins to find it, but did. Placed it in the root of the SDcard along with the update zip. Downloaded Astro file manager from the play store. Went to bottem of list and copied the recovery file, then pasted in system/bin folder. Rebooted, clicked reinstall packages on the stock (blue) recovery screen. But it was a no go. it would not give me the orange CWM. It just ket saying E :file invalid, or some such rubbish. So back to combing the forums again. Had stumbled upon a post some where here, that said something about MNT/SDcard. And sure enough, I copied the recovery file from the MNT/SDcard directory, then pasted in the system/bin. Reboot again, reinstall packages and BAM Orange CWM! But before I flashed my first rom, i wanted to get the red CWM/voodoo recovery. That way I didnt have to worry about mounts while flashing. After much reading again in the forum, I found that the red CWM was already included with the Bali Kernal. Reboot again, then install from SDcard, choose Bali Kernal and installed. Woo Hoo red CWM was up and going. phew.... lol or so I thought. Plugged phone in and put CM6 - Merged on the SD. Back to recovery, wipe factory, wipe cache, wipe dalvik. Then install from SDcard again, chose CM-6 Merged.
This is where I had a bit of a panic. As I was not paying atternion the what Kernal or Baseband the rom was made to run with. So that ended up soft-bricking my phone. But yet again, XDA to the rescue. Searched it out and found the "ODIN to stock" thread. Just had to track down the right TAR and PIT files. I was orginally on KJ2 stock before I did anything, but I could only find the KD1 TAR. No biggie tho, just used the ODIN to stock method and I was back in business again.
Since I am far from having any real knowledge about roms and their internal workings and what-nots. I went about just trying to find roms that would run off of the Bali Kernal and the KD1 baseband. I did find working links to a few of them, not exactly sure how many, but I had serval choices. I went with GingerClone v.2.
Back to reboot, wipe factory, wipe cache, wipe dalvik. Install from SDcard, chose GingerClone and installed. Booted up and everyhting was all hunky dory again. Ran that rom for a few days. And yes it was a really nice rom, and it was faster than stock. It just was quicte what I was looking for.
Back to looking for ROM files, seeing which links were still good and trying to figure out which one I thought would work best for me. Tried TouchMIUIwiz v3, and again very good rom, but still not quite right. Decided to spend a whole day just comparing roms that would work with Bali and KD1. There are only a few roms that are made with KD1. So I wanted to go back to KJ2. I was thinking the only way I could do that was if I wiped again and the hooked up to Kios (or whatever it is called), But no, I found a working like to a KJ2 file. After another set of wiping in recovery, then Flashed the KJ2, then Flashed Nexus CM. Been messing with in for fwe days, and have to say I really really like this one. It has been smooth as glass and quick as a rabbit. I am thinking as long as I dont run into any major problems or bugs with it, this wil be my daily driver.
But I do have a question, since most of you have been here for awhile, and have been able to try out alot of these roms when they were new. Whick rom, in your own opinion, would make web surfing fast and smooth, and also works awesome with facebook? have already rooted and unlocked my husbands SK4G, but he surfs the web and does his facebooking from his SK, and it loves to freeze up and lag out when using both of those things.
Now that I am at the bottom with this, very sorry if my post seemed to long or anything else. Thanks in advance!
That's quite the story there. Crazy to believe it still works.
As for the ROM question, really all of the ROMS for SK4G are outdated. Due to software available. The only ROMS that I would say are up to snuff now are the neXus GB and JB ROMS by RicAndroid. They are chock full of tweaks and scripts. But keep in mind, you're not going to be on the actual newer Android versions. So it may run better, and it may be faster, but only so much.
Hope this helps
Zydrate_blue said:
That's quite the story there. Crazy to believe it still works.
As for the ROM question, really all of the ROMS for SK4G are outdated. Due to software available. The only ROMS that I would say are up to snuff now are the neXus GB and JB ROMS by RicAndroid. They are chock full of tweaks and scripts. But keep in mind, you're not going to be on the actual newer Android versions. So it may run better, and it may be faster, but only so much.
Hope this helps
Click to expand...
Click to collapse
I was pleasantly surprised when it turned out to be just a battery issue.
Thanks for the answer on the roms. I realized that these are older roms now, and its not the most crrrent version of android and all that, and I am totally fine with it. I am just looking for something that is better, smoother and faster than the stock stuff on the phone, for my husband. He still uses his SK4G as well. In fact I dont think I could get him to upgrade to a new smartphone phone/ android device anyways. So I was just looking for something to stop his constant frezzing issue while he is web surfing and things like that. You were very helpful tho, so thanks a bunch.
I agree with Zydrate_Blue; the Nexus JB ROM is about as good as it gets with this phone.
Thanks guys! I will have to d/l and flash it.
CupCakeBombardme said:
Thanks guys! I will have to d/l and flash it.
Click to expand...
Click to collapse
For a smoother internet interface. Get yourself NakedBrowser. They've got a free version that works just lovely. I haven't tried the paid version myself, but if may very well be worth it for someone who uses it a lot!

Desperately in need of quick help with my OnePlus One.

I haven't used my OnePlus One in several months since I got my Nexus 6. I've been meaning to sell my OPO, but got lazy about it. Now I can't be, and I need money for rent. A friend/co-worker who's in serious (in my opinion) need of a new phone wants to buy it off me.
My OPO was on LiquidSmooth 4.4.4 but obviously it's out of date, so I tried to update it. I tried once before to update it with a 5.1 ROM, but it kept failing. I remember there was something about the firmware or baseband version that needed to be flashed to go from KK to LP, but it was several months ago, and I can't remember what exactly it was. And for the life of me, I can't find it.
I tried to find what it was, and in my searching I found that CyanogemMod Official 13 had a built-in baseband updater. So that's what I tried. TWRP version was/is 2.8.7.0. Maybe that was the problem?
Anyway, CM13 (the most recent snapshot) installed, seemingly fine, but it won't recognize my SIM card. I try reinstalling it, and it still won't recognize the SIM. Moreover, it doesn't even detect a cell signal (it should, as all cell phones in the US are required to have 911 emergency access, even if you're not actually paying for phone service). And then it starts rebooting. Not a bootloop, because it boots. Then a few minutes later, it reboots. Continuously.
So I try a different ROM. The latest Resurrection Remix (I have it on my Galaxy S4 and it works fine). Same thing.
The even weirder thing is that I figure I should just restore my latest nandroid, but it's not there. In fact, nothing's there. Nothing visible through TWRP's file manager or backups. Not even old pictures, which I didn't delete. I didn't delete any storage (because I wanted my backup, just in case, duh). But TWRP still shows that there's 26GB available. So obviously, there's something there. I just can't see it. My fault for not saving the nandroid elsewhere, but Humpty Dumpy has already fallen.
I have Wugfresh's toolkit (yeah, yeah, I know...), and tried restoring it to stock, and it won't do it.
I've used ADK in the past, but it has been way to long for me to remember specifics, and it has apparently been updated with the newer Android versions. Obviously, I've looked at the sticky thread about restoring your OPO to stock, but it hasn't been updated in a while. So I'm worried about using those instructions. I've looked up youtube videos, and they're all too old as well. I'm also worried that I'd be using the wrong version of ADK. I'm not scared of using ADK, as long as the instructions are correct and clear. I'd be using Windows 8, if that matters.
So what I'm asking (begging) for is instructions on how to make this phone work properly again. Quickly. I've tried doing the research myself, and haven't found my solution. I'd keep at it, but time is getting short, and I can't afford that. Literally. I can't afford the hours spent (it's 1am and my the office closes at 4pm), and I can't afford being late on my rent. A couple weeks ago I spent way too much up in Phoenix to go see Guns N' Roses (at least I got a kickass T-shirt). Entirely my fault. Also my fault for not realizing how desperate my financial situation was about to be, and for waiting to ask for help until now. And I'm not going to ask to borrow money. I just can't.
Finally, and I know it's taboo to ask "what's the best ROM?", because I've answered that question myself with "there isn't one - try them out for yourself and find which one's best for you". But as I said, I'm out of time., and I haven't been keeping up with what's going on with OPO's development. My friend is not like us. His phone's a LG cheapo POS from years ago that's on 4.1JB. He uses it for calls, texts, and podcasts. He doesn't need root, or even custom recovery for that matter. In fact, I'd prefer if it didn't have root (although custom recovery might be nice, just in case). So if I can get this damn thing working properly again, what'd be a good ROM for my firend? OPO's official Oxygen? Are they still updating it? Stability is the primary concern, but if there's something that gets regular (and stable) updates, that'd be good too. With an updater that's built-in, simple, and wouldn't need and XDA forumite to do it for him. Because it'd be nice that he could get updates with Google's security patches. But since he's still using a 4.1 phone, he's obviously not all that concerned about that issue. But still, that'd be nice.
Thank you (fingers crossed).

Categories

Resources