Hello,
is there a possibility for wireless charging for the Note 10.1 out there?
Anybody who put a coil in it?
Or any external solutions?
I could not find anything about it
regards, Christian
skylineishigh said:
Hello,
is there a possibility for wireless charging for the Note 10.1 out there?
Anybody who put a coil in it?
Or any external solutions?
I could not find anything about it
regards, Christian
Click to expand...
Click to collapse
I have an idea how you could do it with this very thin $17 kit http://www.ebay.com/itm/Free-Shipping-Wireless-Charge-Power-Module-Board-Charger-Kits-For-DIY-/251314383690?pt=US_Cell_Phone_PDA_Chargers&hash=item3a83812b4a
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
and this $11 back case cover. http://www.ebay.com/itm/HEAD-CASE-BLACK-X-HARD-CASE-BACK-CASE-COVER-FOR-SAMSUNG-GALAXY-NOTE-10-1-N8000-/190851314616?pt=US_Tablet_eReader_Cases_Covers_Keyboard_Folios&hash=item2c6f9ff3b8
If you sanded off the tabs on this hard cover that hold the Note 10.1 the Note would then just lay in the hard shell and you could get perfect coil alignment without using magnets.
So..... with some odds and ends you most likely already have (tape, soldering iron, hot melt glue, an old usb cable) you could do this for under $30 bucks.
The only 3 issue's I see is will the Note 10.1 charge with only 600 ma of power (not likely), is there enough room to fit the coil under the back cover (good chance) and were do you connect the 5 volt power lead inside the case??????
Here is a disassembly video http://www.youtube.com/watch?v=PUyI74c0DhE that may help if anyone decides to tackle this project because I'm not ready to risking my $400 dollar investment, maybe if I find one with a cracked screen on ebay for cheap I might try it.
.
Related
If i cannot sell my phone here - Please ask and I will remove the post.
I have a brand new O2 XDA for sale. It is an unwanted upgrade and could do with the cash. I have a XDA Orbit already and I am very happy with it.
£275 + Posting and packaging.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Included is:
Micro SD Card (1 GB)
Stylus x2
Rechargeable Lithium-ion polymer battery
USB Connector
Velvet Protective Carry Case/Pouch
AC Charger
USB to PC Sync Cable
Headset Control Add On
Headset Soft Ear-Buds
Quick Start Guide
Full User Manual (CD-Rom)
CoPilot 7 Live GPS CD
CoPilot 7 Live Serial Number Card
GPS User Guide
Car Mount & Cradle
In Car Charger
Thanks for looking...
Cheers
Tiny
No takers?
I will be putting it on Ebay then...
I will listen to sensible offers for it.
Cheers
Tiny
I'm sorry for not having the resources to figure this out....but how much would that be in USD?
I think I might be interested if its affordable to me. Second, is it brand new or used?
Oh...I should probably ask are you willing to ship to US?
That's about $512.00.
crunluath is correct, it's approximately $500... Postage would be on top of that.
It's brand new and boxed. I have opened the box to check the contents and that's it. I've not even switched it on, so whoever buys it will be the first one to use it!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Features:
Data HotSync and battery charging on your desk with a cradle.
Blue light through the LOGO.
For opod S900,HTC P3700 ,HTC diamond etc
Size: 90*60*23 , N.W. :92g , with data lines,intelligent IC control circuit, overcharge and overcurrent protection, high temperature protection design. Safe and Reliable . Back side with skidproof glue, stable performance, mercury, lead, cadmium and other harmful substances, in full compliance with environmental requirements. Use the ultrasonic technology, Not dismantle and Install .
Can you tell me where to buy this docking station?
Thanks in advanced
Why is it white ?
What interested me is the battery, it said 1800mAh?
But is it thicker than the original one?
Yep you ned a other backcuver for it, I just received a batery I ordered a 1800mAh but got a 2000 mAh I just bought it cause it so cheap from Deal Extreme, and believe it or not I am positive suprised by the thikness of it.
Willem
Wilsas said:
Can you tell me where to buy this docking station?
Thanks in advanced
Click to expand...
Click to collapse
You can contact them.MSN:[email protected]
AnthRaX_Thy said:
What interested me is the battery, it said 1800mAh?
But is it thicker than the original one?
Click to expand...
Click to collapse
Yes ,you are right.The battery is 1800mAh,and it is thicker than the original ,so it need a other backcuver for it.
I thought the Ori was pretty cool and hard to pass up at $30 even if it doesn't fit the best.
I ordered the Ori and used it for a bit and could see why some of the negative comments about it not securely holding the touch pad were made. I then started thinking of possible solutions to this (I also mod computers and cars) and in about 5 minutes I had a solution. I've been testing it out for a while now and it works brilliantly.
I bought the following trim pieces:
Polyethylene Edge Trim w/ Adhesive
Neoprene Rubber Edge Trim
From this site: (did I mention I mod cars too?)
http://customcargrills.com/products.asp?cat=45
The fitment with the trim pieces is nearly perfect and the touchpad is in there solid. The trim pieces do not extend higher than the TP so the cover fits as if the trim pieces weren't even there. I just need to get time to cut/drill out holes for the head phone jack and speakers.
I had thought about posting up a teaser saying that I had a solution to give me time to get a short video put together but I know how I hate those threads so here are some of pics of the results: (using my CM9 Nexus S 4G)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I've held the case so the touch pad is pointing face down and shook it as hard as I could and the touchpad did not come out. I've already ordered another Ori for my 2nd touchpad. I'm loving how functional the ori is. I'm just wanting to get a netbook sleeve for it to cover it when traveling and such to protect stuff from the metal case.
Hey guys! Just a heads up on this USB adapter I snagged from USBfever:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
IT ALLOWS YOU TO CHARGE VIA USB! It should, of course, be noted that it will probably not charge as fast as it would with the OEM charger or any 2 amp charger. But it does work. It didn't take long to get it (they ship from Hong Kong) and the price is worth it. I have also used it with my Sharper Image portable power pack with success. May have to get myself another one as a backup.
I bought the same one...
Also bought the SD/USB adapter and pickup a original galaxy tab dock for gen 1 model for a fiver down the market,
The dock is a tight fit but I dremeled a slit down the side so it fits much better....
MUST HAVE it too
Sent from my Galaxy Note with DarkyROM 3.3
I have one of those too, but is too tight of a fit for me to dare use it. That's not necessarily representative for other units though, as these chinese accessories don't exactly match up from batch to batch
After some more use I've discovered that while it will let me charge via usb it will not actually recognized that it's connected to a computer. But it was still worth not to carry that big block around with me.
Sent from my GT-P6210 using XDA Premium HD app
Hello, I have a Gear 2 R380 and have suffered many of the usual and expected problems. The exposed pins on the watch have corroded and failed, the charging cradle failed and refused to stay connected because the clip broke early on and now I have lost the cradle.
I am looking for information that will make it possible for me to make my own charging and communication solution via USB. I have included a picture of the circuit board in a Galaxy Gear charging cradle and if I can get the same for my gear 2 I would be very grateful!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I am NOT interested in buying another charging cradle that will just break AGAIN and frustrate me by not staying connected to the watch while charging.
I'm also NOT interested in buying a replacement contact board to replace the corroded pads on the watch as that will also just be good money down the drain.
I can solder, 3D print, make from scratch everything I'll need once I have the information on the pins. I also enjoy doing this and will are any solution I come up with.
I have tried searching in the the XDA forums and online ave no found the definitive answer I am looking for. There are threads where asked a similar question to mine but the answers are not often not pertaining to the R380 charging cradle, pads on the watch or the associated pads inside the watch.
If you are worried about me damaging my watch, this is a moot point as I cannot use the watch now anyway. I would really like to start using the watch again, without all the usual frustrations.
TIA
Ryan