Database Info

[Q] SDCARD wont mount.

I have the Optimus T and I installed oxygen ROM on it a while ago.. now out of nowhere my.sd card wont mount. I tried reformatting it to FAT32, I booted into recovery to see if it would mount from there.. but no dice.... I tried factory reset but that dint help either. I'm trying to install twrp and another ROM but i can't because the SD card wont mount. ANY help would be appreciated.

Anyone?.....

Is sd card detects in cwm recovery??
Sent from my LG-P500 using xda premium

no it does not but my gs2 reads and my computer reads it so i know its not the sd card itself. only the phone is the one that wont read any sd card i put in it.

boricua10 said:
no it does not but my gs2 reads and my computer reads it so i know its not the sd card itself. only the phone is the one that wont read any sd card i put in it.
Click to expand...
Click to collapse
i dnt knw if this is helpful
but i had faced this issue once before
this is what i did
inserted the sd into the phone evn though it didnt detect it
then i used kdz flashed stock lg rom
and vola after that sd card was detected by the phone in recovery and otherwise
and then i flashed custom roms
no issues after that

viv_jen said:
i dnt knw if this is helpful
but i had faced this issue once before
this is what i did
inserted the sd into the phone evn though it didnt detect it
then i used kdz flashed stock lg rom
and vola after that sd card was detected by the phone in recovery and otherwise
and then i flashed custom roms
no issues after that
Click to expand...
Click to collapse
How can i go about Flashing the kdz? i have v10s.kdz
I found this topic http://forum.xda-developers.com/showthread.php?t=1149530
Will this help?

boricua10 said:
How can i go about Flashing the kdz? i have v10s.kdz
I found this topic http://forum.xda-developers.com/showthread.php?t=1149530
Will this help?
Click to expand...
Click to collapse
uh thats for changing baseband
what i meant was using kdz to go back to manufacturer OS
i use this guide http://lgp500-optimusone.blogspot.in/2011/10/how-to-install-firmware-using-kdz.html
Hold it you say you have v10?
thats a froyo base
and oxygen is a gb based rom
i think that's where your going wrong
use kdz and flash stock GB
and then flash oxygen

[Q] help plz ..i bricked my O3D p920

hi all
i have flashed custom ics rom and it was working fine
but flashed a kernel and that kernel burns battery too fast i tried another kernel but same problem
so i decide to return to my stock GB
so i flashed GB using LGmobile support tool... phone recovery
then phone started normally but it said corrupted sd card format it but still corrupted
then i go to Settings SD card options but found out all memories are unmounted (Phone memory, internal SD, External SD ) all unmounted
tried to format anyone but not formatted
i tried to boot to recovery to format internal SD from recovery and i booted into TWRP and what ever i do either Wipe format or system reset, it says unable to mount internal sd
i tried to flash another GB rom and GB bootloader and GB TWRP and tried again to flash any GB rom but flash tool give me error message after it fully flash and RESETTING but phone don't boot anymore and LG flash tool give me error message and FAIL
what to do to fix my phone???

i was have same problem before in my su760 u need to flash it with ics kdz and format it format it then downgrade to the first froyo version it gonna work format it in the froyo one and it gonna work

Try this .
http://forum.xda-developers.com/showthread.php?t=1956347
that will help u. good luck

thnx guys
i solved the problem
i flash First ported ics by LG flash tool it gave me error but the phone booted normally and both internal and external SD are formatted
BUT
i still have battery problem
it burns too fast like 1% every 2 minutes
that's bad
anyone plz help me with that
plz plz plz

mktns said:
thnx guys
i solved the problem
i flash First ported ics by LG flash tool it gave me error but the phone booted normally and both internal and external SD are formatted
BUT
i still have battery problem
it burns too fast like 1% every 2 minutes
that's bad
anyone plz help me with that
plz plz plz
Click to expand...
Click to collapse
Man, maybe your battery has a problem...
Try different kernels (make sure they are compatible with your phone), if the problem persists maybe your battery is faulty.

The battery is fine... when I open WiFi or use the phone the battery start burning fast
And when overclocking the battery burns without using the phone
This happened after changing its voltages
I lowed the voltages to save battery but It didn't saved but starts to burn
Any ideas?
Sent from my LG-SU760 using xda app-developers app

[Q] what am i doing wrong?

hi
i have a optimus 3d p920 on orange (uk) (just unlocked to any network)
android version- Gingerbread 2.3.5
software version- V20d june 2012
everytime i try and put a rom on, the phone goes into boot loop (lg logo then unlit black screen)
i root using megatron
install ROM manager
install clockwork recovery 6.0.1
I download zip
plug in phone
cody zip to sd card but NOT external sd card (filemanager shows it as /mnt/sdcard)
go on ROM manager
click on boot in recovery
already done back up of original rom saved on sd card clockworkmodrecovery file
i wipe data/format
i wipe cache partition
then go i go into advance then wipe cache dev
then i go back on to menu
click on install rom from sdcard
find the zip then click yes to install
says its installed then i click reboot and then it becomes stuck
sometimes it would install CM10 or PACMAN (after turning it on and off for a while) then after about 5 mins would reboot its self and get stuck again
so i will then unplug battery, hold Vol up connect usb and open up lg support tool and then recover as carnt get into cwm recovery and install backup from sd card.
i have noticed in the mount/format tab that only the /data is mounted and not (as follows)
/external sd card
/sdcard
/system
/emmc
as they have mount next to them...
its driving me mental
so please help
(if posted in wrong section then sorry im new)

dont bother with GB, we have ICS!!
its much smoother and touch response is way better than GB. Just follow this link
http://forum.xda-developers.com/showthread.php?t=1963847
([ROM][ICS][P920/P925]XBSA ICS V7.2 Custom Full 3D ROM (V28B))
please click on thanks if you think I helped.
schubeir

schubeir said:
dont bother with GB, we have ICS!!
its much smoother and touch response is way better than GB. Just follow this link
http://forum.xda-developers.com/showthread.php?t=1963847
([ROM][ICS][P920/P925]XBSA ICS V7.2 Custom Full 3D ROM (V28B))
please click on thanks if you think I helped.
schubeir
Click to expand...
Click to collapse
Thank you I got the same result when trying your last rom version 6.
But il try this using TeamWin recovery not cwm and defo not ROM Manager (is it a common problem with ROM Manager)
Thank you

I flashed v28b.bin and the .fls through smartflash tool and il installed and then went into twrp recovery to install the ROM after.
I wiped everything and installed the rom rebooted all installed but now i dont have any network or imei.
Baseband now says omap4430/xmm6260 but no service only wifi.
Also the device kept on rebooting after a while to lg boot screen then the
Screen would go dodgy before reloading back to o.s.
So i restored just the v28b but still no network.
Iv just read i should have hardboot after flashing v28b and before install the rom (would that have caused the problems)

Help Needed. Rom Installation

After I rooted my pico and installed CWM and took a nand backup. After that i tried Jaggy Dzire rom which installed perfectly but i don't know how it got bootloop. so i restored my backup and now i can't install any other rom than stock.. even if i try it will get stuck at boot logo or will go in bootloop.
i also managed to get lastet asia_india stock rom and to my wonder it works very well although i can't get link2sd work even if i try different 2nd partition formats( fat, fat32, ext3/4). on doing ext2 it will get stuck on boot.
and i'm curious about do i have nand burnt? ( pico is barely 1 week old).
and would also like to get a better ics/sense rom to use with and yeah, no overclock and stuff. as i can't get anything else than stock rom or my nand back up to boot normally !!.
Current Setup : Philz CWM || pico_asia_1.43.720.2_rev3 (rom).

Qmarks said:
After I rooted my pico and installed CWM and took a nand backup. After that i tried Jaggy Dzire rom which installed perfectly but i don't know how it got bootloop. so i restored my backup and now i can't install any other rom than stock.. even if i try it will get stuck at boot logo or will go in bootloop.
i also managed to get lastet asia_india stock rom and to my wonder it works very well although i can't get link2sd work even if i try different 2nd partition formats( fat, fat32, ext3/4). on doing ext2 it will get stuck on boot.
and i'm curious about do i have nand burnt? ( pico is barely 1 week old).
and would also like to get a better ics/sense rom to use with and yeah, no overclock and stuff. as i can't get anything else than stock rom or my nand back up to boot normally !!.
Current Setup : Philz CWM || pico_asia_1.43.720.2_rev3 (rom).
Click to expand...
Click to collapse
Nope no band burnt
U need to flash recovery again ( I recommend latest twrp )
And try formatting everything
But don't format sd card
Then flash the rom and u will be good to go
Sent from my HTC Explorer using xda premium

I got my phone working again. Running Cyanogenmod 9 with TWRP Recovery.
Here's what i did.
Installed pico_asia_1.43.720.2_rev3.
Installed twrp-2.5.5.0.
then copy-pasted flash_erase file in system/xbin and did ADB command.
reboot.
formatted partitions all of them ( except SDCARD and SD-EXT, can't format it, error occurs as "can't mount SD-EXT || can't format with mk2fs" ).
Installed cm-9-20130304-UNOFFICIAL-pico. and reboot.
And now, Working like a charm.
Thanks for Replying.

Great Work Guys
Qmarks said:
I got my phone working again. Running Cyanogenmod 9 with TWRP Recovery.
Here's what i did.
Installed pico_asia_1.43.720.2_rev3.
Installed twrp-2.5.5.0.
then copy-pasted flash_erase file in system/xbin and did ADB command.
reboot.
formatted partitions all of them ( except SDCARD and SD-EXT, can't format it, error occurs as "can't mount SD-EXT || can't format with mk2fs" ).
Installed cm-9-20130304-UNOFFICIAL-pico. and reboot.
And now, Working like a charm.
Thanks for Replying.
Click to expand...
Click to collapse
So there is no need of ClockWorkMod Recovery to flash CM9 or 10? I thought that was necessary. I never tested cyanogenmod because I never had CWM Recovery installed. But maybe I will give a try. Now I am on NextGen 1.5 and is running great. I changed it 3 days ago. Back than I had derefas's HTC Sense 4.0a Build #8, but had some problems with this and because I have 0 Thanks, I can't post in the actual thread. I would appreciate everyone giving me some "Thanks", if that's possible, so I can post in developement threads. Anyway, wainting for akya's new build. For me it's the best ROM, although it's GingerBread, but hey, it works flawlessly. I begin to think that HTC know what they are doing since they didn't updated the Pico's software to ICS. Gingerbread run's great. Anyways, appreciate derefas, shekhutanwar, Apex-Predator and other's efforts for trying to bring ICS to Explorer. Great work guys. Keep it up!

A custom recovery is must, it's upto you which one you choose. I have TWRP because it's recommended here for our pico and is really easy to use. CWM is none less though and I forgot to mention that I had CWM prior to flashing pico_asia_1.43.720.2_rev3 and after it I flashed TWRP. And as for CM, I used to have it on my Galaxy Note and have liked it since I noob-ly flashed it on my Galaxy Y. CM is way better than Sense/Touchwiz ( although Sense has more appealing UI and TouchWiz is just b.llsh.t). Anyway, Its upto you to decide and yeah, thanks to all our devs here for there precious works.

Qmarks said:
After I rooted my pico and installed CWM and took a nand backup. After that i tried Jaggy Dzire rom which installed perfectly but i don't know how it got bootloop. so i restored my backup and now i can't install any other rom than stock.. even if i try it will get stuck at boot logo or will go in bootloop.
i also managed to get lastet asia_india stock rom and to my wonder it works very well although i can't get link2sd work even if i try different 2nd partition formats( fat, fat32, ext3/4). on doing ext2 it will get stuck on boot.
and i'm curious about do i have nand burnt? ( pico is barely 1 week old).
and would also like to get a better ics/sense rom to use with and yeah, no overclock and stuff. as i can't get anything else than stock rom or my nand back up to boot normally !!.
Current Setup : Philz CWM || pico_asia_1.43.720.2_rev3 (rom).
Click to expand...
Click to collapse
By which method you made your sd-ext partition
Bcoz it seem to like, there is some problem with your sd-ext partition
Sent from my HTC Explorer using xda premium

At first I tried it with MiniTool Partition wizard( Space>512 Mb and tried all recommended partition format. didn't worked) and then again tried through CWM also this time it didn't worked.it showed that partition creation was successful but upon loading the card on my pc it would still displayed as 1 single partition having all the available memory space ie. 1.83 gb.
but then after installing TWRP and CM9 , I tried again through TWRP and made ext3 partition sized 512 MB and using Link2SD .working good since then.
i suppose its an issue on cwm side and the rom which was not able to detect and mount second partition.

SDCARD problem after maximusHD rom install

Hi guys i have a problem
i am installed maximus hd rom
Htc one s S4 ville. 16 gb.
Hboot ver 2.1 and my device
S-off,supercid,unlock and root, twrp recovery
What ever my phone succesfully rom installing and not mount sdcard.
i can't use sdcard . Empty memory 1.6 gb of 16.
Because 14 gb not use
Anybody help i have shock !

[email protected] said:
Hi guys i have a problem
i am installed maximus hd rom
Htc one s S4 ville. 16 gb.
Hboot ver 2.1 and my device
S-off,supercid,unlock and root, twrp recovery
What ever my phone succesfully rom installing and not mount sdcard.
i can't use sdcard . Empty memory 1.6 gb of 16.
Because 14 gb not use
Anybody help i have shock !
Click to expand...
Click to collapse
Me too

Whenever you're installing an ruu, you need to change the super cid back to it's original name.

dooshbag45 said:
Whenever you're installing an ruu, you need to change the super cid back to it's original name.
Click to expand...
Click to collapse
Doesn't Maximus and hboot 2.16 require MTP only access to SDcard? It's all in EXT4 format now, which windows can't see?

That's the reason why I deinstalled Maximus 5 Minutes after setup! There are some pretty good sense 4 and 5 alternatives like Magio or Venom. I don't know how to handle that issue with Maximus, but would be interested how to solve it!
HTC One S - CM 11 4.4.2-S-OFF

[email protected] said:
Hi guys i have a problem
i am installed maximus hd rom
Htc one s S4 ville. 16 gb.
Hboot ver 2.1 and my device
S-off,supercid,unlock and root, twrp recovery
What ever my phone succesfully rom installing and not mount sdcard.
i can't use sdcard . Empty memory 1.6 gb of 16.
Because 14 gb not use
Anybody help i have shock !
Click to expand...
Click to collapse
Well with that hboot, the firmware wasn't installed. You have to follow the instructions. And you also have to use that recovery provided.
And to the others, my pc can access my phone just fine, like any other Rom.
Sent from my HTC One S using Tapatalk