I found the tutorial on Facebook. Took a risk for testing . Modified a bit to suite our needs. Credit goes to original developer.
If procedure not followed properly, it may brick your phone. Go ahead with your own risk.
Requirements: Win XP or Win 7 (all tools set to Win Xp Sp3 Compatibility & Run as Admin), Battery atleast 60%.
Required Files:
Karbonn Drivers Download
Roadkill Download
EMMC Downloader Download
QUALFAST Download
IMEI Writer Download
JB Root Download
AP Firmware Download Part1
Download Part2
BP Firmware Download
Use Driver Signature Enforcement Overrider,from attachments, in Windows 7 to enable test mode and install drivers without any problem.
Credits: Ako si Opaw, strik3r
Procedure
1.Backup your ICS using Roadkill
Turn off your Flare, then press Volume down and power button at the same time. once you see the “ENTRY QPST DOWNLOAD”, open roadkill and click on Store Image Tab, select the disk with 3.61GB, click browse and select the location where you want your backup to be saved, and click start. Once finish proceed to next step.
2. Saving IMEI, MAC ID and Serial Number
Write your IMEI1, IMEI2, Wi-Fi Mac, and Serial Number (S/N) in a piece of tissue paper. For MAC ID, turn on your Wi-Fi, and go to Settings > About Phone > Status. For IMEI just dial *#0000# in dial pad.
3. Backup NVRAM
Run EMMC_DownLoad_V1.2.3.exe ,(Check Download Boot Loader for 1st run)
Turn device ON (make sure USB Debugging is enable)
Connect phone thru microUSB cable (Note: Make sure there are no other USB Modem or phone connected to your computer except for Flare)
Click BackUp_NV.
Wait until back up is successful.
4. Download BP Firmware
Go to ENTRY QPST DOWNLOAD” Mode (Power + Vol Down)
Run EMMC_DownLoad_V1.2.3.exe. Click SELPATH select “BP Firmware” Folder.
Connect phone thru a microUSB cable.
Check Device Manager for "Qualcomm HS-Usb Diagnostics 9006" Com Port #.
Look for "Qualcomm HS-Usb Diagnostics 9006" type the Com port # in EMMC Download Box. Click Download.
Wait until download is successful (Usually it takes 6-12sec). Remove battery. (Do not Close EMMC Download. then proceed to next Step )
5. Download AP Firmware
Run QUALFAST2.0.5.exe. Click SELPATH, select AP firmware (“Stock JB Rom” Folder), Check Format Card & Userdata
Go to Fastboot Mode or Green Screen Mode (Power + Vol Up)
Click OK to start download then connect phone via a microUSB cable.
Wait until download is successful. Remove battery.
6. Restore NVRAM Backup
Run EMMC_DownLoad_V1.2.3.exe.
Turn device ON. (make sure USB Debugging is enable)
Click Restore_NV. Browse and select bak.qcn file. Connect phone thru microUSB cable.
Wait until qcn restore is successful. (your IMEI 2 is Null & Wifi Mac Address is set to default. you need to write it again)
7. IMEI & Wi-Fi MAC Address Writing
Turn device ON (make sure USB Debugging is enable)
Locate your modem com port number (Go to Device Manager > Right-click “Tianyu HS-USB Android Modem 9025” > Properties > Advanced Tab > Advanced Port Settings > COM Port # (Ex. 10))
Open Qualcomm_Modem_Tools_V1.1.2.exe and type com port #
Write all your backup code, then click Write button. (In my case I have re-entered my IMEI1, IMEI2, S/N (Serial Number), Wi-Fi MAC)
Note: Every after successful entry of IMEI, the phone automatically restarts.
8. Rooting
Restart Device. Wait until it boot perfectly.
Copy update.zip to internal memory.
Reboot to recovery and update from internal sdcard.
Reboot
Enjoy.
Reserved one more.......
Hey, Can you help for Karbonn A21 too?? I mean can you change the ramdisk?? And provide a boot.img! Jelly Bean is booting but White screen problem. So I think we've to change the ramdisk of KA9 with the ICS Karbonn A21!! Please do the necessary changes and provide a boot.img??? Please
Sent from my HTC Explorer A310e using xda premium
Hey dude the official update of jelly bean for flatter has started rolling out. I was wondering if you could somehow get tort hands on it soi that even a15 and a21 users can benefit.
Sent from my A15 using xda app-developers app
Minimilised_MR said:
Hey, Can you help for Karbonn A21 too?? I mean can you change the ramdisk?? And provide a boot.img! Jelly Bean is booting but White screen problem. So I think we've to change the ramdisk of KA9 with the ICS Karbonn A21!! Please do the necessary changes and provide a boot.img??? Please
Sent from my HTC Explorer A310e using xda premium
Click to expand...
Click to collapse
Dude kernel is device independent... ramdisk is folder positioning
Hey guys I got a very strange problem.
I successully updated my a9+ to jelly bean, which worked for 3 days. Suddenly while charging my phone, it died. I saw the phone charge upto 93% and when checked later it was turned off. I tried to turn on the phone, fastloader and qpst download entry mode... nothing worked... I thought that there was some hardware malfunction..
Then I tried connecting the dead phone to PC and a device under Qualcomm HS-USB QD Loader 9008 got installed. I search google and came to know about tutorial where you could flash bootloader thorough QPST (Qualcomm Product Support Tool). I followed the tutorial but i received error "Cookie not available", which according to tutorial is not solvable.
I don't know the cause of this problem... Maybe it was eMMC internal flash failure without any fault on JB update... Or something that happened due to jelly bean update process and incompatiblity of the firmware with a9+..
Now my question is:
1. Is my phone eMMC flash damaged physically beyond any repair?
2. Or the service center guys can still access my eMMC flash and repair it?
3. If eMMC is damaged, can it be replaced or the entire board needs to be replace?
It is not job fault. Emmc died. You can get replacement/repair as there is no way to know that u flashed job .
Sent from my SGH-T989 using Tapatalk 4 Beta
Waiting for karbonn to get jellybean
Sent from my Nexus S using xda app-developers app
kornholic said:
Hey guys I got a very strange problem.
I successully updated my a9+ to jelly bean, which worked for 3 days. Suddenly while charging my phone, it died. I saw the phone charge upto 93% and when checked later it was turned off. I tried to turn on the phone, fastloader and qpst download entry mode... nothing worked... I thought that there was some hardware malfunction..
Then I tried connecting the dead phone to PC and a device under Qualcomm HS-USB QD Loader 9008 got installed. I search google and came to know about tutorial where you could flash bootloader thorough QPST (Qualcomm Product Support Tool). I followed the tutorial but i received error "Cookie not available", which according to tutorial is not solvable.
I don't know the cause of this problem... Maybe it was eMMC internal flash failure without any fault on JB update... Or something that happened due to jelly bean update process and incompatiblity of the firmware with a9+..
Now my question is:
1. Is my phone eMMC flash damaged physically beyond any repair?
2. Or the service center guys can still access my eMMC flash and repair it?
3. If eMMC is damaged, can it be replaced or the entire board needs to be replace?
Click to expand...
Click to collapse
I posted another thread for reviving the phone. Make sure u are on WinXP.
Sent from my SGH-T989 using Tapatalk 4 Beta
3rd step not working for me... says Backup -nv failed
and can u make a zip file which can be flashed.... would be of great help for a lot of people.... but still great work... keep it up
+1
Same here.
Is there any comport issue?
Sent from my Nexus S using xda app-developers app
Issue fixed now.
Just manually install karbon drivers first to creat a comport.
Arun you should add that step to your procedure for jb update.
I successfully update it and working awesome
Sent from my S100 using xda app-developers app
i have karbonn A111 and same configuration to karbonn a9+
can i try to update using following method?
its also qualcomm 1.2 dual core, 512 ram
display is litle bigger
what u say ? can i go for it or it will go dead
sam1skhan said:
i have karbonn A111 and same configuration to karbonn a9+
can i try to update using following method?
its also qualcomm 1.2 dual core, 512 ram
display is litle bigger
what u say ? can i go for it or it will go dead
Click to expand...
Click to collapse
since the display is bigger you may have to replace some library files..
i seen some tutorial ,, still new to it. and committed to learn .
can u tell which library , or put a link for referance
thank you
br
skhan
(i done backup with roadkill n qcn backup is there for me)
thank you for the post. not facing any issues and my phone works better now and very happy with the procedure provided by you.
I didn't get u? what does karbon drives have to do with Backup_nv? Please can u explain the step properly
---------- Post added at 12:05 PM ---------- Previous post was at 12:03 PM ----------
leecorp said:
Issue fixed now.
Just manually install karbon drivers first to creat a comport.
Arun you should add that step to your procedure for jb update.
I successfully update it and working awesome
Sent from my S100 using xda app-developers app
Click to expand...
Click to collapse
I didn't get u? what is the connection b/w karbonn drivers and bavkup_nv?
Can u explain the steps in detail?//
It's not concern with backup_nv it requires you to when you install bp firmware and further steps. It requires comport.
Sent from my S100 using xda app-developers app
leecorp said:
It's not concern with backup_nv it requires you to when you install bp firmware and further steps. It requires comport.
Sent from my S100 using xda app-developers app
Click to expand...
Click to collapse
i downloaded karbon drivers from first post but can u tell me how to install them.
why is backup_nv is failing.... what is comport & how to get/do it?????
the com no. showing is 254... should i change it... if so where can i get correct no.
Related
This method successfully installs the CWM on the phone. CWM version supplied by ZOPO does not work. Use the CWM posted in the second link
I am a still learning and not a developer !
Hi All ZOPO ZP900 Leader Owners,
This is a guide for Installing Clock Work Mod Recovery Image on ZOPO ZP900 Leader Phone. Most of the owners of this fantastic phone would have desperately tried like me to install CWM on this phone (some may have found success). ZOPO does gives an option to order the phone pre-rooted however they do not install CWM ....or for that matter there is no Stock Recovery on the phone !!!. Start the phone with Power + Volume Up button pressed and your presented with an image of sick Android lying down with a Red triangle coming out of his opened stomach :laugh:
DONT TRY TO USE ROM MANAGER APP TO INSTALL CWM, THIS WILL ONLY BRICK YOUR PHONE !
So after breaking my head for couple of days, searching the net, downloading stuff I have successfully installed CWM !
So here are the steps !.
What you need
1. ZOPO ZP900 Leader phone
2. Download Fully working English CWM from here http://www.4shared.com/file/16vuWyiU/recovery.html. The one posted in Zopo website does not work.
3. Download latest SP Flash Tool for MTK6577 from here http://www.4shared.com/zip/Xgc3G_hB/SP_Flash_Tool_v3122200.html
4. Download the latest Stock ICS ROM for ZP900 from Zopo website link http://www.4shared.com/rar/hGY2ahbu/MP_MT77_root_en_play_fix_zp900.html
5. Download MTK6577 Driver from Zopo website http://www.4shared.com/zip/YXlLFoLm/6577driver_install_3_steps.html
Installation Steps
1. Unzip and Install the USB drivers on your Windows PC using the MTK 6577 Driver Zip file. There will be 3 folders named First Step, Second Step & Third Step. Open First Step install the MTK driver MSI file. Post completion open Second Step, click on ClickInstall Driver, it will automatically install the USB driver. Press Exit after installation (Win 7 may give error that installation was incorrect, just ignore)
Repeat the same for folder Third Step
Connect your phone switched off and battery removed using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Put the battery back but do not switch on the phone
2.Extract the latest ROM folder from downloaded ICS ROM. You will get 2 folders
database
MP_MT77_h958_zp900_zwx_ics_20120912-155136_TSZ_PC
Open the second folder (MP_MT77***). This is the folder that has all the image files. You will find recovery.img file. This is original file. You can either rename it or keep a back up and delete it.
3. Copy the new CWM recovery.img file that you downloaded from ZOPO website in this folder. Rename it to be recovery.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5.Click on Options, USB Mode will be checked, DA Download All will be checked, in the sub options Speed will be Checked High Speed, Battery select With Battery. Come to the main Application window
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your extracted ICS ROM folder, click on folder MP_MT77****. By default you will have only one map file of name MT6577_Android_scatter_emmc. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "RECOVERY". Leave Recovery checked.
9. Now click on "Download" on the Application or press F9 on keyboard. A warning message will pop up. Press YES
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this the Congrats You have flashed CWM !
Check by unplugging the phone and re-starting it with Power+Volume Up button Pressed. The Phone will boot into CWM !.
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
Now I hope this opens the door for many other things !
Additional Info -
Install PDAnet from here http://www.junefabrics.com/android/download.php or Snappea from www.snappea.com to make your device get recognized when connected to the computer. Install this with your phone switched on, this software installs the necessary drivers for the phone, post which you can use flash tool.
reserved
The CWM from taiwan101 for the 9300+ seems to be working fine. I was able to install .zip file from SD card. However the CWM is in Taiwanese, so if anyone can provide the CWM in English, thanks in advance
link for 9300+ CWM http://d01.megashares.com/dl/KicT315...M_Recovery.rar
UPDATE - Finally got a full working English CWM for ZOPO extracted from Mod ROM posted thanks to Kyrie1965. Tested and everything is working. Download from here http://www.4shared.com/file/16vuWyiU/recovery.html
vijayar said:
This method successfully installs the CWM on the phone. CWM as such works (able to navigate through the menus etc) but some of the function such as Install from ZIP, Backup etc, mount are not working, Gives an error Unable to Mount Sdcard !. Not sure if the issue is with CWM version supplied by ZOPO, need to try with other/older versions of CWM.
Please feel free to post links of CWM that works
I am a still learning and not a developer !
Hi All ZOPO ZP900 Leader Owners,
This is a guide for Installing Clock Work Mod Recovery Image on ZOPO ZP900 Leader Phone. Most of the owners of this fantastic phone would have desperately tried like me to install CWM on this phone (some may have found success). ZOPO does gives an option to order the phone pre-rooted however they do not install CWM ....or for that matter there is no Stock Recovery on the phone !!!. Start the phone with Power + Volume Up button pressed and your presented with an image of sick Android lying down with a Red triangle coming out of his opened stomach :laugh:
DONT TRY TO USE ROM MANAGER APP TO INSTALL CWM, THIS WILL ONLY BRICK YOUR PHONE !
So after breaking my head for couple of days, searching the net, downloading stuff I have successfully installed CWM !
So here are the steps !.
What you need
1. ZOPO ZP900 Leader phone
2. Download latest CWM from the link provided in Zopo Website http://www.4shared.com/file/lp0t5E1t/cmw-recovery.html
3. Download latest SP Flash Tool for MTK6577 from here http://www.4shared.com/zip/Xgc3G_hB/SP_Flash_Tool_v3122200.html
4. Download the latest Stock ICS ROM for ZP900 from Zopo website link http://www.4shared.com/rar/hGY2ahbu/MP_MT77_root_en_play_fix_zp900.html
5. Download MTK6577 Driver from Zopo website http://www.4shared.com/zip/YXlLFoLm/6577driver_install_3_steps.html
Installation Steps
1. Unzip and Install the USB drivers on your Windows PC using the MTK 6577 Driver Zip file. There will be 3 folders named First Step, Second Step & Third Step. Open First Step install the MTK driver MSI file. Post completion open Second Step, click on ClickInstall Driver, it will automatically install the USB driver. Press Exit after installation (Win 7 may give error that installation was incorrect, just ignore)
Repeat the same for folder Third Step
Connect your phone switched off and battery removed using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Put the battery back but do not switch on the phone
2.Extract the latest ROM folder from downloaded ICS ROM. You will get 2 folders
database
MP_MT77_h958_zp900_zwx_ics_20120912-155136_TSZ_PC
Open the second folder (MP_MT77***). This is the folder that has all the image files. You will find recovery.img file. This is original file. You can either rename it or keep a back up and delete it.
3. Copy the new CWM recovery.img file that you downloaded from ZOPO website in this folder. Rename it to be recovery.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5.Click on Options, USB Mode will be checked, DA Download All will be checked, in the sub options Speed will be Checked High Speed, Battery select With Battery. Come to the main Application window
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your extracted ICS ROM folder, click on folder MP_MT77****. By default you will have only one map file of name MT6577_Android_scatter_emmc. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "RECOVERY". Leave Recovery checked.
9. Now click on "Download" on the Application or press F9 on keyboard. A warning message will pop up. Press YES
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this the Congrats You have flashed CWM !
Check by unplugging the phone and re-starting it with Power+Volume Up button Pressed. The Phone will boot into CWM !.
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
Now I hope this opens the door for many other things !
Click to expand...
Click to collapse
hey will this work on hero 9300+ ,512mb ram .
i have ordered one and will soon arrive.
will try to make some custom roms.
B rom error:
hi there does anyone has flash the zopo900 leader and got the message B ROM ERROR: S_COM_PORT_OPEN_FAIL (1013)
It wont letme flash the phone driver seems working fine but it said "single usb port" and the port assing it. please help!
Hi Vijay,
What if i dont follow the step 8 (uncheck everything except recovery). Does it cause any issue?
I am running win 7 x64 and when i run the flash tool it says searching only after i click the download
help
hey i have hero 9300+ 512mb ram
i have no network issue plz help me!:crying:
miraguilar1 said:
hi there does anyone has flash the zopo900 leader and got the message B ROM ERROR: S_COM_PORT_OPEN_FAIL (1013)
It wont letme flash the phone driver seems working fine but it said "single usb port" and the port assing it. please help!
Click to expand...
Click to collapse
Check your device drivers USB driver has not been installed properly. I faced this issue and after multiple attempts of reinstall of USB drivers the flash tool started working properly
Also you can try installing PDAnet from here http://www.junefabrics.com/android/download.php
Install this with your phone switched on, this software installs the necessary drivers for the phone, post which you can use flash tool.
Note Connect the phone to flash tool first without battery, in options select with battery, press download after selecting the required file, when it says searching unplug the phone put battery back, dont switch on, plus back the usb. The flash tool should load the required file.
senlakshman said:
Hi Vijay,
What if i dont follow the step 8 (uncheck everything except recovery). Does it cause any issue?
I am running win 7 x64 and when i run the flash tool it says searching only after i click the download
Click to expand...
Click to collapse
It will flash the entire ROM again. My guide was specifically for flashing only the CWM and not the entire ROM. I wanted to keep the Stock rom intact as it came from ZOPO.
Word of caution, I am yet top try flashing the complete ROM so if you are trying ensure that your have taken a backup via CWM (if already flashed) of your existing full working ROM before attempting anything. Also flash only ZOPO Stock or customised ROMs,
From where did you bought this mobile?
Does the imei start from 355,889,3535
Is it ips 1gb ram .
Sent from my GT-I9100 using xda premium
Anyone having problem with drivers can follow this http://www.youtube.com/watch?v=Rfemoi6Aizw
complete flashing process
Sent from my GT-I9100 using xda premium
vijayar said:
It will flash the entire ROM again. My guide was specifically for flashing only the CWM and not the entire ROM. I wanted to keep the Stock rom intact as it came from ZOPO.
Word of caution, I am yet top try flashing the complete ROM so if you are trying ensure that your have taken a backup via CWM (if already flashed) of your existing full working ROM before attempting anything. Also flash only ZOPO Stock or customised ROMs,
Click to expand...
Click to collapse
I have installed the drivers, while the phone is on using pdanet and i powered off and ran the flash tool first without battery (with battery option) and put the battery back in. but i got message stating please insert usb and Flashtool have this alert.
Not sure, where i am missing the steps
plz also have a look at previous posts u will get your answer.
senlakshman said:
I have installed the drivers, while the phone is on using pdanet and i powered off and ran the flash tool first without battery (with battery option) and put the battery back in. but i got message stating please insert usb and Flashtool have this alert.
Not sure, where i am missing the steps
Click to expand...
Click to collapse
i too was having this problem but i tried the MTK6575 DRIVER and it worked maybe give it a try
Hey guys, I want to try this on my hero 9300+.
Is it safe?
Working
bhargav1991 said:
hey will this work on hero 9300+ ,512mb ram .
i have ordered one and will soon arrive.
will try to make some custom roms.
Click to expand...
Click to collapse
Confirmed working on 9300+
Follow the tutorial exactly as written.
---------- Post added at 10:38 PM ---------- Previous post was at 10:28 PM ----------
Israeleet said:
Hey guys, I want to try this on my hero 9300+.
Is it safe?
Click to expand...
Click to collapse
This is a copy of cwm with the specific support for the MTK6577 used by the 9300+
So yes it safe.
---------- Post added at 10:46 PM ---------- Previous post was at 10:38 PM ----------
bhargav1991 said:
hey i have hero 9300+ 512mb ram
i have no network issue plz help me!:crying:
Click to expand...
Click to collapse
Make sure you removed the battery long enough from your phone.
You may also have to reboot your pc a couple of times.
Wtf .
I am talking about the no service issue,it doesn't have any relation
With battery or pc :what:
Anyways its an imei issue.
Sent from my GT-I9100 using xda premium
vattmann said:
i too was having this problem but i tried the MTK6575 DRIVER and it worked maybe give it a try
Click to expand...
Click to collapse
Yessss , it did worked by using the MTK6575 driver :good:
bhargav1991 said:
Wtf .
I am talking about the no service issue,it doesn't have any relation
With battery or pc :what:
Anyways its an imei issue.
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
YTF
This is the CWM forum.
Has anyone tried tw5 launcher on this ?
Sent from my GT-I9100 using xda premium
bhargav1991 said:
Anyone having problem with drivers can follow this http://www.youtube.com/watch?v=Rfemoi6Aizw
complete flashing process
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
Hello bhargav1991, i got some questions:
1. I've buy zp900 but it will arrive next week. In the video you posted there is a guide how to flash the official Zopo z900 latest stock ROM but in this way you get the latest rom + root but no ClockWorkMod Recovery installed ?¿¿
2. My intention as i done with my old..HTC Desire HD is flashing ClockWorkMod Recovery and install the latest Zp 900 stock ROM + ROOT. So following the 1st post and once all steps are done one by one, will I get the same rom that come installed ?¿ but non root ?¿
I need to download the latest ZOPO ROM .zip and then install it from ClockWorkMod and finally i will get the latest ROM + ROOT ¿?
Could you please help me
Thank you so much in advance guys ¡¡
:good:
MICROMAX A78 ROOTED!!!
Guys!!! Micromax a78!! rooted!!!
So, here are the steps on getting root access on MICROMAX A78-
What you need
1. MICROMAX A78, data usb cable.
2. Download the Rooted Boot image file from the attachment below this post.
3. Download SP Flash Tool v2.1 from HERE.
4. Download MTK65xx Driver from HERE.
5. Download the MTK6573 Scatter.txt file from the attachment below this post.
6. Lastly download SuperOneClick root application for windows (search google), and install it...it will also install the adb drivers needed while rooting.
Installation Steps-
1. Unzip and Install the MTK65xx USB drivers on your Windows PC, just run setup.exe.
Connect your phone switched off and connect using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Do not switch on the phone
2. Copy the "rootedboot.img" file that you downloaded from my attatchment. Rename it to be boot.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5. Click on Options, check USB mode.
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your downloaded scatter.txt file. By default you will have only one map file of name MT6573_Android_scatter. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "BOOT". Leave boot checked. Now click on the "BOOT" just right to the checkbox and browse and select the boot.img (which was earlier rootedboot.img) file you downloaded from the attachment below.
9. Now click on "Download" on the Application or press F9 on keyboard. Warning messages will occur, but ignore them..
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this then Congrats You have flashed the unlocked boot.img!
NOW FOR ACTUAL ROOTING:
1. Restart your phone, now when the phone boots up, enable "usb debugging".
2. Now run SuperOneClick, and click "root"..after the process finishes, the a78 will be fully rooted with Superuser app installed!!.
Check by installing root checker from play store!!!
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
Credits!
I, Me, Myself
GUYS! If u think my hardwork is worth something, do press the "Thanks" button below! Thank You! :fingers-crossed:
awesome work !!!
thankyou buddy !!! my phone is finally rooted now waiting for a custom recovery ........
I'll also make a custom recovery if you are interested
Sent from my Micromax A110 using xda app-developers app
I will post the result after testing your method on my A78. Lets hope for something good
Bro!! You are the best.. Thanks a lot!!!
abs_dear said:
Bro!! You are the best.. Thanks a lot!!!
Click to expand...
Click to collapse
That's good to know! Any problems anybody faces,m always there
Sent from my Micromax A110 using xda app-developers app
WOOT WOOT
vshlkmr buddy you are the BEST :good:
i tried with SOC bt didnt wrk..n i ws worried to play with SP flash tool coz i dnt hv any alternt phone...excellent job man...
will root my phone ASAP n let u know if i get any problms..
it'll be perfect if you can provide CWM recovery...
THANKS again..
Hi,
Facing a strange issue and that too at very first step. When I am connecting the phone (Switched Off) to USB Cable after Driver Installation, Windows detects the device and tries to install MT65xx PreLoader. But after a few seconds, it shows the error: Device Unplugged.
Can you plz help to resolve this ?
Thanks,
Param
paramjeetgem said:
Hi,
Facing a strange issue and that too at very first step. When I am connecting the phone (Switched Off) to USB Cable after Driver Installation, Windows detects the device and tries to install MT65xx PreLoader. But after a few seconds, it shows the error: Device Unplugged.
Can you plz help to resolve this ?
Thanks,
Param
Click to expand...
Click to collapse
Ok, I am able to resolve this by Disabling Searching Windows Update for Device Drivers.
And, YES, I have rooted my A78
Big Big Thanks to vshlkmr
Phone Finally from rotted to Rooted
Thanks Buddy...
Phone is finally of some use now.
vshlkmr said:
I'll also make a custom recovery if you are interested
Click to expand...
Click to collapse
Yes, we are very interested. please make a custom recovery for a78.
Thanks
I searched the forums but couldn't find any answers. This is the first time I'm trying to root an android phone. Things are not going well..
I found a page in Indonesian with instruction on how to root my sister's Lenovo S890. My dad bought her one in China, we live in Europe.
We need to get all the Chinese stuff off and install a "regular" Android version with a normal marketplace (read: whatsapp and google and nothing blocked).
The page with instructions is at http://www.duniaku.net/2013/03/30/u...rtisi-internal-storage-lenovo-ideaphone-s890/ I used Google Translate.
What are the steps? First you need to set up some files such as drivers are required to carry out the process of flashing, SP Flash Tool version 3.1222 or higher, because Lenny chipset MTK6577 S890, S890 and file TWRP to also file a Super User and Busybox will be pushed into the system through TWRP. All the files you can download from the following link:
1 Download Driver Lenovo : Extract file. rar it and then click Install_Driver.exe to install drivers into the system. Rather long process, just wait.
2 Download SP Flash Tool : The author gave the newer version, which v3.1224.01. .
3 Download Team Win Recovery Project : TWRP file is specific to the Lenovo S890, so do not try for another Android, although it also MediaTek chipset.
4 Download Super User and Busybox : Will we push into the system through TWRP custom recovery. Download and copy directly to SD Storage / Memory Cards-mu. Place it outside the / root folder or USB Storage Storage SD / USB storage from your Lenovo S890.
5 Download Data Repartition : This file is optional, just download and place it in the root folder Storage SD / USB Storage. Can later be used to repartition the internal memory is too small Lenovo S890. Author will explain at the bottom.
Click to expand...
Click to collapse
I first installed the Lenovo S890 drivers. Clicked "Install anyway" for everything and rebooted. No problems.
But when I connect the phone it's still complaining that it can't find drivers (and I can't find any official drivers on the Lenovo website either)?
I also installed the MT6577 USB VCOM drivers that I found here http://forum.xda-developers.com/showthread.php?t=2206421 (before I did this the SP Flash Tool did nothing).
I enabled USB Debugging mode on the phone, and took out the SIM, the SD card and the battery when I connect it to USB to the PC. I am running Win7x64.
Every time I try to run (step 2) SP Flash tool, it starts downloading fine, but then Win7 'spits out' the phone (I can hear the 'usb device disconnected' sound) and SP Flash Tool obviously stops working then and gives some error.
I think this is because the MediaTek MT6577 USB VCOM drivers somehow refuse to install correctly? It looks like rooting might go well once this driver thing is fixed?
When I force installation of the drivers I get a Code 10 error and a yellow triangle next to the Preloader and the MediaTEL Vcom something USB driver in Windows Device Manager. ( I searched the forums and didn't find a solution for this).
I forced installation by opening Device Manager, click Add, click Add Legacy Hardware - manual - choose the usb2ser_Win764.info file out of the MT6577 USB VCOM drivers folder
This is what's in the .inf file : Is there anything I can change here to force it to work?
[Version]
Signature="$Windows NT$"
Class=Ports
ClassGuid={4D36E978-E325-11CE-BFC1-08002BE10318}
Provider=%MTK%
DriverVer=05/30/2011,1.1123.0
[Manufacturer]
%MTK%=MTK,NTamd64
[MTK.NTamd64]
%MTK6218%=Reader,USB\Vid_0e8d&Pid_0003,USB\Vid_0e8d&Pid_1003
%MTK_COM%=Reader,USB\Vid_0e8d&Pid_0023&MI_00
%MTK_CAT%=Reader,USB\Vid_0e8d&Pid_0023&MI_02
%MTK_PRELOADER%=Reader, USB\Vid_0e8d&Pid_2000
%MTK_SP_DA%=Reader, USB\Vid_0e8d&Pid_2001
[DestinationDirs]
DefaultDestDir=12
[Reader.NTamd64]
Include=mdmcpq.inf
AddReg=Reader.NTamd64.AddReg
CopyFiles=FakeModemCopyFileSection
[Reader.NTamd64.AddReg]
HKR,,DevLoader,,*ntkern
HKR,,NTMPDriver,,usbser.sys
HKR,,EnumPropPages32,,"MsPorts.dll,SerialPortPropPageProvider"
[Reader.NTamd64.Services]
AddService = usbser, 0x00000002, Service_Inst
[SourceDisksNames]
[SourceDisksFiles]
[Service_Inst]
DisplayName = %Serial.SvcDesc%
ServiceType = 1 ; SERVICE_KERNEL_DRIVER
StartType = 3 ; SERVICE_DEMAND_START
ErrorControl = 1 ; SERVICE_ERROR_NORMAL
ServiceBinary = %12%\usbser.sys
LoadOrderGroup = Base
[Strings]
MTK = "MediaTek Inc."
MTK6218 = "MTK USB Port"
MTK_COM = "MTK USB Modem Port"
MTK_CAT = "MTK USB Debug Port"
MTK_PRELOADER = "MediaTek PreLoader USB VCOM Port"
MTK_SP_DA = "MediaTek DA USB VCOM Port"
Serial.SvcDesc = "USB Serial emulation modem driver"
Click to expand...
Click to collapse
How do I stop Windows from ejecting the phone (force it to keep it connected as the MediaTek thingie that seems to work with SP Flash Tool?).
Or is there a better way to get an English Android version on this phone?
When I now try to boot the phone it says
tool dl image fail
uboot is blocking by dl info
Did I (soft)brick it??
Thanks in advance for all the help!!
Giving up
Since this seems to be a less popular phone with very little support available - I'm giving up.
Spent 3 full days on this thing with no results, and I just read the GPS also won't work outside of China either.
Now all I need to do is figure out how to get it out of META mode or Factory mode, and get it to boot back into it's normal Chinese Android system.
katejones said:
Since this seems to be a less popular phone with very little support available - I'm giving up.
Spent 3 full days on this thing with no results, and I just read the GPS also won't work outside of China either.
Now all I need to do is figure out how to get it out of META mode or Factory mode, and get it to boot back into it's normal Chinese Android system.
Click to expand...
Click to collapse
Hi, I'm having a much similar problem, since I couldn't flash recovery with SP flash tool, the process was terminated unexpectedly showing error message s_ft_need_download_all_fail (4050), after a couple of days looking for a solution I decided to format the phone with SP Flash Tool, and it worked, right after I tried to flas recovery again...and it worked. I thought I had found the way but when I tried to boot the phone in recovery mode nothing happened, no matter what keys combination I use, how long I press them, the phone just won't react, it doesn't show anything on the screen.
I don't know if this was the logic step to follow, but if you want to try and discover what to do next, up to you, 4 hands are better than 2,maybe yuo find the solution.
Good luck.
There is no button combination to boot recovery, try droidgram-reboot on play store.
Sent from my Lenovo S880
Hope you guys manage to root it soon as I am one of those who waiting for it as I need to root my S890 also.
Sent from my Lenovo S890 using xda app-developers app
katejones said:
I searched the forums but couldn't find any answers. This is the first time I'm trying to root an android phone. Things are not going well..
I found a page in Indonesian with instruction on how to root my sister's Lenovo S890. My dad bought her one in China, we live in Europe.
We need to get all the Chinese stuff off and install a "regular" Android version with a normal marketplace (read: whatsapp and google and nothing blocked).
The page with instructions is at http://www.duniaku.net/2013/03/30/u...rtisi-internal-storage-lenovo-ideaphone-s890/ I used Google Translate.
I first installed the Lenovo S890 drivers. Clicked "Install anyway" for everything and rebooted. No problems.
But when I connect the phone it's still complaining that it can't find drivers (and I can't find any official drivers on the Lenovo website either)?
I also installed the MT6577 USB VCOM drivers that I found here http://forum.xda-developers.com/showthread.php?t=2206421 (before I did this the SP Flash Tool did nothing).
I enabled USB Debugging mode on the phone, and took out the SIM, the SD card and the battery when I connect it to USB to the PC. I am running Win7x64.
Every time I try to run (step 2) SP Flash tool, it starts downloading fine, but then Win7 'spits out' the phone (I can hear the 'usb device disconnected' sound) and SP Flash Tool obviously stops working then and gives some error.
I think this is because the MediaTek MT6577 USB VCOM drivers somehow refuse to install correctly? It looks like rooting might go well once this driver thing is fixed?
When I force installation of the drivers I get a Code 10 error and a yellow triangle next to the Preloader and the MediaTEL Vcom something USB driver in Windows Device Manager. ( I searched the forums and didn't find a solution for this).
I forced installation by opening Device Manager, click Add, click Add Legacy Hardware - manual - choose the usb2ser_Win764.info file out of the MT6577 USB VCOM drivers folder
This is what's in the .inf file : Is there anything I can change here to force it to work?
How do I stop Windows from ejecting the phone (force it to keep it connected as the MediaTek thingie that seems to work with SP Flash Tool?).
Or is there a better way to get an English Android version on this phone?
When I now try to boot the phone it says
tool dl image fail
uboot is blocking by dl info
Did I (soft)brick it??
Thanks in advance for all the help!!
Click to expand...
Click to collapse
please use S890_Customized_SP_Flashtool_20121119(v3.1238.5)
flash again ok
i am solve same your problem
https://www.dropbox.com/s/pwvg553v5z1vtju/S890_Customized_SP_Flashtool_20130109(v3.1238.5).rar
kyaw8719 said:
please use S890_Customized_SP_Flashtool_20121119(v3.1238.5)
flash again ok
i am solve same your problem
https://www.dropbox.com/s/pwvg553v5z1vtju/S890_Customized_SP_Flashtool_20130109(v3.1238.5).rar
Click to expand...
Click to collapse
Thanks for sharing. Is it 100% working or still in testing phase?
Sent from my Lenovo S890 using xda app-developers app
nakTT said:
Thanks for sharing. Is it 100% working or still in testing phase?
Sent from my Lenovo S890 using xda app-developers app
Click to expand...
Click to collapse
i fix 2pcs
kyaw8719 said:
i fix 2pcs
Click to expand...
Click to collapse
Meaning?
Sent from my ST26i
doesn't solve the problem
nakTT said:
Meaning?
Sent from my ST26i
Click to expand...
Click to collapse
It doesn't work same problem downloaded the latest SP Flash from the post doesn't work either.. Is there any of you solved the problem? If so then please go detailed about it.
Follow this guide carefully and you can revive your dead Karbonn A9+/ CM Flare after Jelly Bean Upgrade.
Tools Needed:
Dead Phone (When u connect to PC it should install Qualcomm HS-USB QD Loader 9008 Driver) Link
QPST.2.7.399 Link
Flare Revival kit Link
PC with 32 bit Windows (XP/Vista/7/8) (64bit casus problem in QPST installation)
Credit goes to jhanra for the tutorial as well as CWM 6.0.1.1 for JB ROM . :good:
Procedure
Connect ur phone to PC and let the driver install
Install QPST
Open QPST Configuration (in Win XP compatibility mode) ->Add new port -> Select the com port of your device ->exit.
Go to Start -> All Programs -> QPST eMMC Software Download open the tool -> Check program boot loaders -> Browse for the device com port
Extract Flare Revival Kit on desktop
If Phone is not detected , Click Browse
In flash programmer file name type MPRG8X25.hex -> in Boot Image type 8X25_msimage.mbn in SPC ->000000
Click Load XML def and browse for rawprogram0.xml in Flare Revival Kit
Click Load Patch def and browse for patch0.xml
Check the search path 2 and browse for the folder flare repair files
Now click download, wait for the download to finish (it never finish but it also detects for a new driver, and that’s important) and it will search for the new hardware found, install the driver
From here you can updating your rom to jelly bean using this tutorial Link
Guys, anyone encountering "Cookie (if present) not received" error after clicking on Download button?
My Karbonn A9+ as successfully updated to jelly bean, which was working flawlessly for 3 days. But suddenly it died while my charging my phone.. The phone could not be turned on, no fastloader or entry download mode.... However when connected to PC it was being detected as Qualcomm HS-USB QD Loader 9008. I tried this tutorial but am facing cookie not received error.
Since my phone died suddenly, not during any update firmware process... I suspect this could be case of Sudden Death Syndrome (SDS) which means my eMMC flash (internal storage) got corrupted and is not being able to recoginized by QPST tool.
Has anyone faced this problem?
kornholic said:
Guys, anyone encountering "Cookie (if present) not received" error after clicking on Download button?
My Karbonn A9+ as successfully updated to jelly bean, which was working flawlessly for 3 days. But suddenly it died while my charging my phone.. The phone could not be turned on, no fastloader or entry download mode.... However when connected to PC it was being detected as Qualcomm HS-USB QD Loader 9008. I tried this tutorial but am facing cookie not received error.
Since my phone died suddenly, not during any update firmware process... I suspect this could be case of Sudden Death Syndrome (SDS) which means my eMMC flash (internal storage) got corrupted and is not being able to recoginized by QPST tool.
Has anyone faced this problem?
Click to expand...
Click to collapse
Please state your OS Win XP or 7. Try using 32 bit win XP PC.
arunmcops said:
Please state your OS Win XP or 7. Try using 32 bit win XP PC.
Click to expand...
Click to collapse
My os is windows 7 32 bit.. i tried running emmc downloader with windows xp compatibility mode also. same problem.
kornholic said:
My os is windows 7 32 bit.. i tried running emmc downloader with windows xp compatibility mode also. same problem.
Click to expand...
Click to collapse
QPST caused me problems with Win 7. I used win XP.
arunmcops said:
QPST caused me problems with Win 7. I used win XP.
Click to expand...
Click to collapse
Tried it on Win XP... same cookie(if present) not received error showing..
can we use vmplayer for the win xp or other virtual soever instead? i use win 8 64 bit that's why it won't able me to download and shows me the message that the cookie (if present) is not received. :angel::angel::angel:
Some from a chinese forum was able to fix the cookie problem through QFPROM Fuse..
http:// lepad.it168.com/thread-2920933-1-1.html
(its in chinese)
What does it mean?
kornholic said:
Some from a chinese forum was able to fix the cookie problem through QFPROM Fuse..
http:// lepad.it168.com/thread-2920933-1-1.html
(its in chinese)
What does it mean?
Click to expand...
Click to collapse
Only explanation given is that This problem is related to specific PC.
arunmcops said:
Only explanation given is that This problem is related to specific PC.
Click to expand...
Click to collapse
Yes the person in one post first said the problem is due to PC and driver combination. However, in later post has also said:
"i am still stuck in download mode. i was able to programm the bootloader, as i mentioned before by using QFPROM Fuse, everything else leads to errors. only one little detail changed -> when i press the power button it vibrates shortly.when i try to porgram the mmc device i always get no response from the phone."
Some of the points to ponder are:
1. He said he was able to program bootloader using qfprom fuse.
(How did he program bootloader through qfprom fuse, what does this mean?)
2. When power button pressed, there is vibration...
(On my device there is no response when pressed on power on.)
3. However he later said when he tries to program mm, he gets no response.
(He has not said he gets cookie error, just not response... could be anything)
one of the moderator of cherry flare group at facebook was able to revive phone from cookie error.
check http://www.youtube.com/watch?v=qHQIIsqV1Zw
i just found out that you can restore your phone too by using roadkill, if you had written the backup of the image of your phone lately. :angel:
heyyanyan said:
i just found out that you can restore your phone too by using roadkill, if you had written the backup of the image of your phone lately. :angel:
Click to expand...
Click to collapse
yes, if you could access entry qpst download mode (vol down + power)... however if you are hard bricked... you would not be able to access that plus your phone would not turn on in any manner.
in my case, my phone didn't turn on no matter what i do. but if i connect my phone to the pc, it shows the qualcomm hs-usb something that can be read by roadkill.
heyyanyan said:
in my case, my phone didn't turn on no matter what i do. but if i connect my phone to the pc, it shows the qualcomm hs-usb something that can be read by roadkill.
Click to expand...
Click to collapse
did you manage to fix your phone?? ......................................................
arunmcops said:
Connect ur phone to PC and let the driver install
Install QPST
Open QPST Configuration (in Win XP compatibility mode) ->Add new port -> Select the com port of your device ->exit.
Go to Start -> All Programs -> QPST eMMC Software Download open the tool -> Check program boot loaders -> Browse for the device com port
Extract Flare Revival Kit on desktop
If Phone is not detected , Click Browse
In flash programmer file name type MPRG8X25.hex -> in Boot Image type 8X25_msimage.mbn in SPC ->000000
Click Load XML def and browse for rawprogram0.xml in Flare Revival Kit
Click Load Patch def and browse for patch0.xml
Check the search path 2 and browse for the folder flare repair files
Now click download, wait for the download to finish (it never finish but it also detects for a new driver, and that’s important) and it will search for the new hardware found, install the driver
From here you can updating your rom to jelly bean using this tutorial Link
Click to expand...
Click to collapse
!!!
!? I just Ported CWM 6.0.1.1 to CM Flare Jelly bean (for JELLY BEAN ONLY)!! !!!! I Already test it with my own 3pcs CM FLARE phone with no problem! In porting this CWM my 2 phone died porting this CWM but I recover it WITH THIS METHOD you posted!!!!!!!!!!!!!!
FLash this with AIO FLASHER
check recovery erase then flash
View attachment 2089726
theres nothing it can do if you try it? it cannot mess your phone!
!!!
this is the full tutorial for this! View attachment 2089809,
and this is the file for this case!
h ttp://www.4shared.co m/rar/rzVTMMxY/flare_repair_files.html
after this you can flash BP firmware in this! follow the tut in flashing BP Firmware and so on
to upgrading in jelly bean BY ARUNMCOPS! here ht tp://forum. xda-developers.com/ showthread.php?t=2330823
the original thread is here ht tp://www.pinoy den.com.ph/inde x.php?topic=274677.0
Note: just erase the spaces of the link!
you can try the steps on my tut but DO THIS AT YOUR OWN RISK!!!
!!!!!!
[email protected]@@
[MENTION=1065870 [user=1879310]@@@@[/user][/MENTION]
@@@
kornholic
@@@????
Today I will tell you how to root one of the quite hard to root phones Qmobile Noir A2 Classic
WARNING:
- I am not responsible for bricked phones
- This tutorial will remove all data from your phone! Be sure to backup your phone book,messages,etc
- This Tutorial is for Qmobile Noir A2 Classic ONLY
Things To Download :-
Adb Drivers http://ge.tt/2yL21VT
Mtk Root and Tools http://dfiles.ru/files/fmnok7ke7
Vcom Drivers
Windows 8 http://www.mediafire.com/?7yee2of64nhl947
WIndows 7/xp/vista http://www.mediafire.com/?cypm22rgs2k83ji
SP Flash Tool http://www.mediafire.com/?agsj3n4neniq054
Scatter File https://www.dropbox.com/s/je0alc5db8t66ld/MT6575_Android_scatter.txt
Super Su ttp://db.tt/owvX0f7t
ROM http://db.tt/n7RhDp0l
Preloader and dsp_bl https://www.dropbox.com/s/prdtpd8px8649yx/preloader and dsp.zip
NOTE:
Write down you imei somewhere (press *#06# on dialer)
You will be needing it
Method:
-Install all Drivers
-Put scatter file ,extract rom and preloader,dsp_bl in one folder (makes things quite easy) replace if asked
-Turn off phone
-Open Sp Flash tool open scatter file and select the scatter file u downloaded
-put tick on all files on sp flash tool and select its corresponding file (for eg "ANDROID" is system.img)
-Click Firmware Upgrade on sp flash tool and connect phone (turned off)
-It Will show error! Disconnect Phone
-Remove tick from all files
-Now put tick on "BOOTIMG" "UBOOT" "RECOVERY" "LOGO"
-Press Download button and connect phone again (remove battery this time)
-It Will show green circle showing success!
-Disconnect Phone and Turn on phone in recovery mode (Press Vol+ with power button)
-(to navigate in recovery mode press vol + to go up press vol - to go down and press power to enter selection)
TO MAKE BACKUP: in recovery mode enter backup and restore, and backup it will take few mins
TO COPY BACKUP: in recovery mode find mounts and storage and turn on usb mount and connect your phone to computer while being at that mode a removeable drive will show up copy the clockworkmod folder
Okay now listen carefully go to the folder where you downloaded the rom (the one you downloaded from me) find the file system.img
rename it to system.yaffs2.img
then go to the folder where you copied the backup to you will find also system.yaffs2.img there replace that file with the file from the rom (the one you renamed earlier) next open the file "nandroid.md5" with notepad delete all the text it has and save it
now copy this folder back to your phone (replacing the old folder) and the Super su zip u downloaded earlier reboot your recovery (after copying back the backup it is important) NOW:
- factory reset
- go to backup and restore -> advance restore ->restore system
- go to update from sd card and select the super su zip
- reboot your phone normally
After the reboot your phone will be rooted But your imei will be lost
Here what you will do restore your imei:
1. remove all sim cards from phone ,turn on the phone in normal mode and connect it
2. open mtk tools press root button it will ask you for some thing just click ok
3. Click replace imei and enter the imei numbers (can be found on phone box or back of phone)
4. Click ok reboot your phone check for updated imei numbers
And Congratulation Your Phone is Rooted
Credits
@najamahmedisb (testing)
@trm33 (testing)
@threatalive (created the thread resulting in this tutorial)
@rua1 (MTK Droid and Tools)
I can confirm that this method does not only root A2 Classic but it can also repair bricked A2 Classic :victory:
@bilalz400 you may update the title, so the thread is easily accessible to people in need.
Awesome guide! :good:
I'll tell someone with this mobile if I come across one. People are using these alot since they're quality phones with reasonable prices.
when i press root button in MKT Droid Tool this error comes what should i do .....
--- ERROR : SU inaccessible
My phone is still with invalid imei
what should i do.....
could anyone plz provide me framework_res.apk(in system/framework) flashable need urgent<<<<thnkx in advance as fast as possible @bilalz400
RaoTayyab said:
when i press root button in MKT Droid Tool this error comes what should i do .....
--- ERROR : SU inaccessible
My phone is still with invalid imei
what should i do.....
Click to expand...
Click to collapse
Is you phone rooted do you have su in you app drawer? check again
najamahmedisb said:
could anyone plz provide me framework_res.apk(in system/framework) flashable need urgent<<<<thnkx in advance as fast as possible @bilalz400
Click to expand...
Click to collapse
Wow bro you mess you phone fast
Hows the quest for modding going on?
Contact @qmobilea2
He might help you in modding your phone
and for your file open mtk droid root and tools go to the root,backup and recovery section click unpack yaffs2 for the section and select system.img from the backup you used earlier this will extract the whole system.img and you will have all the system files you want to replace!
Sry for the late reply's i didnt checked the thread
bilalz400 said:
Is you phone rooted do you have su in you app drawer? check again
Click to expand...
Click to collapse
Yes phone is rooted and su was problem which i again installed after restarting phone... Then MKtdroid Tool replace imei numbers as you said above.....
Thank you very much... I am very happy with your work...... You are helping the newbies in the world of IT etc.... Thnx
RaoTayyab said:
Yes phone is rooted and su was problem which i again installed after restarting phone... Then MKtdroid Tool replace imei numbers as you said above.....
Thank you very much... I am very happy with your work...... You are helping the newbies in the world of IT etc.... Thnx
Click to expand...
Click to collapse
Very Happy to see your imei restored
can't copy backup
i can't move forward.... stuck at ''to copy backup''
removable drive is not showing..
please help me
thanks
simply root it with Vroot
This method is very complicated just simple root it with voot 1.7.2 sofware , you just all those drivers witch come with Q mobile software. Juts simple put mobile in dubugging mode , once sofware detected your mobile just simply press the Root button , your wmobile will restart once and its finally rooted . No need for all this stuff. I rooted my friend's A2 Classic with that method , if you want some screenshots i can provide that to.
Easy Rooting Method.
- I am not responsible for bricked phones
-and i am also not responsible if someone hit a bricked phone in your head
-don't worry your data remain safe :laugh::laugh:
Method:
first and first download the software from attached files below the post :good::good::good:
1) Install all the drivers (as the original post suggested ADB and VCOM )
2) turn USB debugging on.
3) Install the software , its in chinese but not very difficult to understand Just press the middle button once installed it should be looked like this (check the attachment )
4) press the button , let the software do its things, once your cell phone restart check the SU app in the drawer.
Caution: Do not Factory restore your phone after freezing apps or modification you will end up in a boot loop.
So what you do with this little Rooted device ?? duh off course make ext 4 partition on your SD Card and link your newly download aps using link2SD . no worrying of low space
AhsanKhaan said:
This method is very complicated just simple root it with voot 1.7.2 sofware , you just all those drivers witch come with Q mobile software. Juts simple put mobile in dubugging mode , once sofware detected your mobile just simply press the Root button , your wmobile will restart once and its finally rooted . No need for all this stuff. I rooted my friend's A2 Classic with that method , if you want some screenshots i can provide that to.
Click to expand...
Click to collapse
Well if it works that will be a huge bonus!
Sent from my A2_Classic using xda app-developers app
Adnan Farooq Chatha said:
i can't move forward.... stuck at ''to copy backup''
removable drive is not showing..
please help me
thanks
Click to expand...
Click to collapse
Use a memory card reader if removable disk does not appear
Sent from my A2_Classic using xda app-developers app
Also make sure u have a mem card in phone and it is detected if removeable disk does not appear than use mem card reader and copy backup to it
Sent from my A2_Classic using xda app-developers app
New framework etc.....
From files which us sent......having one problem this one.....which I p.m u
sent from my beast...
najamahmedisb said:
From files which us sent......having one problem this one.....which I p.m u
sent from my beast...
Click to expand...
Click to collapse
Bro i already looked into it and trying to fix it
don't post into this thread its a guide not a discussion one
root problem
hey can you help me how can I root my a2 classic?
it doesn't do anything in sp flash tool when I click frimware upgrade? or I click download?
bilalz400 said:
Also make sure u have a mem card in phone and it is detected if removeable disk does not appear than use mem card reader and copy backup to it
Sent from my A2_Classic using xda app-developers app
Click to expand...
Click to collapse
how to flash that stock rom qmobile noir i5 wt is that file type MTK6582_1408270534 filetype is GGoSaVoe plz tell me plz help me no forum for qmobile noir i5 thats why i posted here kindly tell me how to flash that stock rom on phone with which software
atir usman butt said:
how to flash that stock rom qmobile noir i5 wt is that file type MTK6582_1408270534 filetype is GGoSaVoe plz tell me plz help me no forum for qmobile noir i5 thats why i posted here kindly tell me how to flash that stock rom on phone with which software
Click to expand...
Click to collapse
Where did you got that file ?