Telus APN - AT&T Samsung Galaxy S 4 General

Telus Mobility LTE APN Settings are as Follows (if you flashed a rom and cannot get data check your apn settings to see if they correspond)
NAME : TELUS SP
APN : SP.TELUS.COM
PROXY : NOT SET
PORT : NOT SET
USERNAME: NOT SET
PASSWORD : NOT SET
SERVER : NOT SET
MMSC : HTTP://ALIASREDIRECT.NET/PROXY/MMSC
MMS PROXY: 74.49.0.18
MMS PORT: 80
MCC: 302
MNC: 220
AUTHENTICATION TYPE: NONE
APN TYPE : DEFAULT, MMS
APN PROTOCOL : IPV4
ENABLE/DISABLE APN: APN ENABLED (CHECKED)
BEARER: UNSPECIFIED
NAME: TELUS ISP
APN: ISP.TELUS.COM
PROXY NOT SET
PORT NOT SET
USERNAME NOT SET
PASSWORD NTO SET
SERVER NOT SET
MMSC NOT SET
MMS PROXY NOT SET
MMS PORT NOT SET
MCC 302
MNC 220
AUTHENTICATION TYPE NONE
APN TYPE DUN
APN PROTOCOL IPV4
ENABLE/DISABLE APN APN ENABLED (CHECKED)
BEARER UNSPECIFIED

yeahitsgotahemii said:
NAME : TELUS SP
APN : SP.TELUS.COM
.
:
APN TYPE : DEFAULT, MMS, SUPL
Click to expand...
Click to collapse
Don't know if it makes any difference but my stock APN settings include "supl" in the TELUS SP APN Type field.

Case sensitivity also, especially for APN field (should be all lower-case)!

Related

[Q] mms problem rooted dream on Telus

I am having a problem with mms on Dream/G1. I am currently running the following CyanogenMod 5.0.8-DS on my phone. My APN settings are:
APN sp.telus.com
Proxy 74.49.0.18
Port 80
Username not set
Password not set
Server not set
MMSC http://aliasredirect.net/proxy/mmsc
MMS proxy 74.49.0.18
Port 80
MCC 302
MNC 220
APN type default, mms
I have tried turning off wifi & GPS and still can't download a pic that was sent from Telus as a test. I am puzzled because internet and phone functions work ok so any help will be appreciated.

APN Settings for Nexus 5 On Straight Talk Using AT&T SIM

You Don't need a New Sim . I have one of the original At&t Sims from ST.
Okay Gents it's been a long time since I've been on Android and I am Happy to be back.
My Last post was With the EVO4G and I was waiting for the next best phone to come out and the N5 is the one.
I've looked everyhwere for APN settings for the N5 using staright talk AT&T SIM with no luck .
So through trial and error I have found the APN setttings that are working. You don't need a New SIM just set up your phone as I will explain.
Set Up 2 APNs one I have labeled :
Name : Internet_line
APN: att.mvno
Proxy: Not Set
Port: Not set
Username: Not set
Pass: Not set
Server: Not set
MMSC: http://mmsc.cingular.com
MMS Proxy: 66.209.11.33
MMS PORT: 80
MCC :310Name : Internet_line
MNC: 410
Authentication Type: None
APN Type: default,supl,mms,hipri ( No spaces)
APN Proto: IPv4
APN roaming Proto : IPv4
Bearer: Unspecified
MVNO Type: None
2nd APN
Name: Straight Talk
APN: tfdata
Proxy: Not Set
Port: 80
Username: Not set
Pass: Not set
Server: Not set
MMSC: http://mms3.tracfone.com
MMS Proxy: Not Set
MMS PORT: 80
MCC :310
MNC:410
A Type: None
APN: default,supl,mms,hipri ( No spaces)
APN Proto: IPv4
APN roaming Proto : IPv4
Bearer: Unspecified
MVNO Type: None
MNC:410
Authentecation Type: PAP or CHAP
APN type:mms
APN Proto: IPv4
APN roaming Proto : IPv4
Bearer: Unspecified
MVNO Type: None
ONCE YOU HAVE SAVED BOTH NEW APNs select the INternet Line One att.mvno
and Enjoy. Just hit Thanks on my post and pass it forward Happy to be Back on Android :victory:
flojo73 said:
You Don't need a New Sim . I have one of the original At&t Sims from ST.
Okay Gents it's been a long time since I've been on Android and I am Happy to be back.
My Last post was With the EVO4G and I was waiting for the next best phone to come out and the N5 is the one.
I've looked everyhwere for APN settings for the N5 using staright talk AT&T SIM with no luck .
So through trial and error I have found the APN setttings that are working. You don't need a New SIM just set up your phone as I will explain.
Set Up 2 APNs one I have labeled :
Name : Internet_line
APN: att.mvno
Proxy: Not Set
Port: Not set
Username: Not set
Pass: Not set
Server: Not set
MMSC: http://mmsc.cingular.com
MMS Proxy: 66.209.11.33
MMS PORT: 80
MCC :310Name : Internet_line
MNC: 410
Authentication Type: None
APN Type: default,supl,mms,hipri ( No spaces)
APN Proto: IPv4
APN roaming Proto : IPv4
Bearer: Unspecified
MVNO Type: None
2nd APN
Name: Straight Talk
APN: tfdata
Proxy: Not Set
Port: 80
Username: Not set
Pass: Not set
Server: Not set
MMSC: http://mms3.tracfone.com
MMS Proxy: Not Set
MMS PORT: 80
MCC :310
MNC:410
A Type: None
APN: default,supl,mms,hipri ( No spaces)
APN Proto: IPv4
APN roaming Proto : IPv4
Bearer: Unspecified
MVNO Type: None
MNC:410
Authentecation Type: PAP or CHAP
APN type:mms
APN Proto: IPv4
APN roaming Proto : IPv4
Bearer: Unspecified
MVNO Type: None
ONCE YOU HAVE SAVED BOTH NEW APNs select the INternet Line One att.mvno
and Enjoy. Just hit Thanks on my post and pass it forward Happy to be Back on Android :victory:
Click to expand...
Click to collapse
The settings from their website work fine for me. No problems with LTE or MMS.
http://www.straighttalkbyop.com/program.php
Auto Refill Confirmation, MMS receive works!
Good day
I authorized a NEXUS 5 Sunday, ATT Micro Sim from Straight Talk
I used the APN settings from the website, last Sunday without any luck receiving MMS messages
I tried every setting on XDA I could find without any receive MMS success
Last night I received a confirmation from Straight Talk thanking me for my Auto Refill Signup
MMS receive started working right after that, go figure.
I am on the Straight Talk APN Settings, nothing different.:good:

APN & SETTINGS for OTHER (not VZN) mobile operators

Many of us are using Verizon M8 with other mobile operators.
As this device is not in other operators' catalogue, they don't publish correct APN & settings information, and I think it could be helpful if we share WORKING configurations here.
IMPORTANT: I know APN are published everywhere in the internet, but when I used them on my device, most of them turned out to be unuseful. The key here is to publish only working configurations.
Yoigo (Spain)
*Network settings>Network preference>
It will ask you to "add network". Type 21404, then "ok", and select GSM/UMTS/LTE. It will say list is full, don't bother about it.​
*Network Settings>Preferred Network>
Select LTE/GSM/UMTS mode​
*Network Settings>GMS/UMTS Options>Access Point Names>
You've got to add two. First:​ Name: Yoigo Navegador
APN: internet
Proxy: Not set
Port: Not set
Username: Not set
Pasword: Not set
Server: Not set
MMSC: Not set
MMS proxy: Not set
MMS port: Not set
MMS protocol: WAP 2.0
MCC: 214 <--Should be grayed out
MNC: 04 <--Should be grayed out
Authentication type: None
APN type: default,hipri,dun,supl
APN protocol: IPv4
APN roamin protocol: IPv4
APN enable/disable: APN enabled <--Should be grayed out
Bearer: Unspecified​
Then you save (top right corner), go back, and add another:​ Name: Yoigo MMS
APN: mms
Proxy: Not set
Port: Not set
Username: Not set
Pasword: Not set
Server: Not set
MMSC: http://mmss/
MMS proxy: 193.209.134.141
MMS port: 80
MMS protocol: WAP 2.0
MCC: 214 <--Should be grayed out
MNC: 04 <--Should be grayed out
Authentication type: None
APN type: Not set
APN protocol: IPv4
APN roamin protocol: IPv4
APN enable/disable: APN enabled <--Should be grayed out
Bearer: Unspecified​
Save and THAT'S ALL. Your device should be connecting voice/data 2G/3G/4G where available. :good:

Tello APN Settings

Dropping this here so I can find it later if I need it, and to help any soul out who hasn't had a chance to call customer service. I just edited the default APNs in the CM13.
For USA Sprint Tello Network:
Name: Sprint LTE
APN: n.mi.ispsn
Username: [email protected]
MMSC: http://mms.sprintpcs.com
MMS proxy: 68.28.31.7
MMS port: 80
MCC:310
MNC:120
APN Type: default,mms
Bearer: LTE
For MMS a new APN needs to be added (requires restart, on CM13 APN is not visible in manager, so verify it is correct on first entry)
Name: Sprint mms
APN: cinet.spcs
mmsc: http://mms.sprintpcs.com/servlets/mms
mms proxy: 68.28.31.7
proxy port: 80
APN Type: mms
bearer: LTE
toxigenicpoem said:
Dropping this here so I can find it later if I need it, and to help any soul out who hasn't had a chance to call customer service. I just edited the default APNs in the CM13.
For USA Sprint Tello Network:
Name: Sprint LTE
APN: n.mi.ispsn
Username: [email protected]
MMSC: http://mms.sprintpcs.com
MMS proxy: 68.28.31.7
MMS port: 80
MCC:310
MNC:120
APN Type: default,mms
Bearer: LTE
For MMS a new APN needs to be added (requires restart, on CM13 APN is not visible in manager, so verify it is correct on first entry)
Name: Sprint mms
APN: cinet.spcs
mmsc: http://mms.sprintpcs.com/servlets/mms
mms proxy: 68.28.31.7
proxy port: 80
APN Type: mms
bearer: LTE
Click to expand...
Click to collapse
Thank you:good:
Tello Internet/MMS 4G APN Settings For Android 10
APN access point
Name, internet
APN, n.mi.ispsn
Proxy, Not set
Port, Not set
Username, Not set
Password, Not set
Server, Not set
MMSC, http://mms.plspictures.com
MMS proxy, oap7.sprintpcs.com
MMS port, 80
MCC 312
MNC 530
Authentication type, Not set
APN type, default,mms
APN protocol, IPv4/IPv6
APN roaming protocol, IPv4
APN enable/disable, APN enabled
Bearer, eHRPD, LTE
MVNO type, GID
MVNO value, A00165FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
* The stock Android ROM shows MCC, 310, MNC, 000. But with the Lineage ROM, MCC312/MNC530 get LTE after rebooting, when the 310/000 were input manually, the APN will crash/disappear by itself.

Cannot set MNC in APN settings. Deletes entire APN settings when changed.

I recently changed carriers and had to update my APN settings. The APN settings requires me to change the MNC to 410 but when I do this and save the APN settings it instantly deletes the entire setting.
Attempting to use this apn setting.
(Edited out links due to new user)
Code:
Name : Straight Talk
APN : tfdata
Proxy : proxy(dot)mvno(dot)tracfone(dot)com
Port: : 80
MMSC : http : // mms-tf(dot)net
MMS Proxy : mms3(dot)tracfone(dot)com
MMS Port : 80
MCC : 310
MNC: 410
APN Type : default,mms,supl
I have tried altering every single other field and it saves just fine until I try to edit the MNC from 260 (or blank when creating a new APN) to 410 and attempt to save.
Using the latest default MIUI updates.
I'm having this same issue currently. Did you ever get this resolved?

Categories

Resources