Hi guys I'm new here.
So here's the problem. My One S z560e dropped of my pocket on the floor. Landed on screen. Screen is broken and on the surface of the screen i can't feel cracked screen just see under there are cracks in left corner of screen. I cant turn on phone, when plugged in orange led is on like is charging. When charging it gets very hot not as usual charging when phone was working. Everything is stock. I have z560e version. I am sure that screen and digitizer are broken but why i cant turn it on? Motherboard maybe?
Thanks for reply's :laugh:
the best thing to do is to take it to hTC
I think u should sell your htc one s ebay as broken and the buy a new one
sent to htc...screen and motherboard were dead...lost some of data backup succesfully worked for me
thanks guys
Related
I recently got a touch pro of a friend with a damaged screen that didn't turn on but the touch screen was responsive. Apparently he sat on it and the screen broke.
I then acquired it and replaced the LCD screen and i turned it on but all it shows is a blank black screen with the backlight on. I was tapping while it booted up and it was making that beep noise so i know the touch screen works. What do i do now.
dazz245 said:
I recently got a touch pro of a friend with a damaged screen that didn't turn on but the touch screen was responsive. Apparently he sat on it and the screen broke.
I then acquired it and replaced the screen (with digitalizer) and i turned it on but all it shows is a blank black screen. I was tapping while it booted up and it was making that beep noise so i know the touch screen works. What do i do now.
Click to expand...
Click to collapse
if the lcd is damaged and you only replaced the digitizer then that wont solve the problem, the digitizer just sits ontop of the lcd and recognizes your touches, hence why it mite know that your touching the screen but the screen is still blank
mancsoulja said:
if the lcd is damaged and you only replaced the digitizer then that wont solve the problem, the digitizer just sits ontop of the lcd and recognizes your touches, hence why it mite know that your touching the screen but the screen is still blank
Click to expand...
Click to collapse
I replaced the LCD along with the digitalizer. Tats what i meant.
Sounds like either the new screen is inop on fit (fraid you need another to test, then send the first back as faulty), or the fault is not the LCD itself.
Possibily its the wrong screen, or its not installed correctly, or you damaged either the screen or the controller when installing.
I'm afraid you dont have many options - take it apart & rebuild to ensure correct parts & fitment, spend £££ on alternative parts to see whats broken (or serious £££ on test equipment!), send it off for repair or give up!
I'd go for option 1 first
If your friend sat on it hard enough to break the screen, i'd be looking for any damage / cracking to the boards / ribon cable mounts and be looking very carefully at the mountings of any IC chips. Incedently, when (s)he sat on it, did the screen work at all? and was it 100% working before they did?
Okay thanks for the replies. I just bought a flex cable where the slider thing is because the old one looked a bit old and flexed out and on inspection of the old screen i found a tiny rip on the screen's flex cable too. I wait for my cable and see if it works and if it doesn't then i'll sent the screen back as faulty and get a new one and if that doesn't work then I'll give up and sell it again
hi
sorry to wake up an old thread.
so what's your solution/conclusion?
is it the flex, or the LCD that broke?
i have the same problem right now.
thanks
was mainboard
I just dropped my phone yesterday once and it was ok, put the battery and the lid back on, boots up everythings fine,but in the next 8 hours, I can see black dots on my screen and they are like mostly on the right side of the screen scattered all around.
Also Ive googled the problem and many people say its the digitizer, do I have to buy new digitizer now?
Kennypachi said:
I just dropped my phone yesterday once and it was ok, put the battery and the lid back on, boots up everythings fine,but in the next 8 hours, I can see black dots on my screen and they are like mostly on the right side of the screen scattered all around.
Also Ive googled the problem and many people say its the digitizer, do I have to buy new digitizer now?
Click to expand...
Click to collapse
I belive the problem is the Lcd not the digitizer,after all the digitizer is flexible plastic with with very thin wires.
The best way is to get the complete package ,lcd and digitizer, normally you can find them in ebay.
faria said:
I belive the problem is the Lcd not the digitizer,after all the digitizer is flexible plastic with with very thin wires.
The best way is to get the complete package ,lcd and digitizer, normally you can find them in ebay.
Click to expand...
Click to collapse
Thank you, im gonna go and search for them in eBay and replace them
But be carefull ,dont just buy any any screen! Apparently there is diferent screen models across the model,make sure you know the part number currently installed in your device .
I had the same problem with my Hermes, had to remove the broken screen to make sure i ordered the rigth one at the time there where 3 diferent screens for my device model but only one woud work.
Read this,it should help you,
http://forum.xda-developers.com/showthread.php?t=1006593
Thank you!
Something weird happened, I turned off the phone, took out the battery, went to sleep for 9 hours. In the morning ive put the battery back on and turned phone on and ALOT of dots have disappeared. What could have caused that?
Kennypachi said:
Something weird happened, I turned off the phone, took out the battery, went to sleep for 9 hours. In the morning ive put the battery back on and turned phone on and ALOT of dots have disappeared. What could have caused that?
Click to expand...
Click to collapse
It sounds like the liquid matrix got displaced when you dropped the device, and now it stabilized itself.
Gravity is an amazing thing
Very good news
faria said:
It sounds like the liquid matrix got displaced when you dropped the device, and now it stabilized itself.
Gravity is an amazing thing
Very good news
Click to expand...
Click to collapse
Liquid!??!?! In my phone!?!??!
Kennypachi said:
Liquid!??!?! In my phone!?!??!
Click to expand...
Click to collapse
i got liquid in my htc screen now its broken!!!
As of now, ALL dots have disappeared itself, checked on completely black and on white picture. Ordered new digitizer and screen just in case though
So i purchased a LCD/digitizer from eBay and received it in the mail this morning. I followed the steps and was able to get my cracked screen (digitzer&lcd) off. After assembling it all with the new screen i ran into an issue.
There is no response from the screen at all it is just black. The phone boots fine though because it vibrated and then a few minutes later i can hear my notifications go off and the led is flashing.
could it be a bad connection with the wires, if so what one should I look at, Did i buy a faulty screen, or am i just sol?
is there any difference between a One X and a One XL screen?
any help is appreciated.
purchased from here: http://www.ebay.com/itm/271006361868?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649#ht_2923wt_1218
Could be bad connection..there is a YouTube vid on replacing it..
Sent from my HTC One X using XDA
yea that is what i am assuming since nothing was working but i just wanted to see if anyone else ran into this issue :/
I've successfully replaced the lcd/digitizer on my htc one xl, and gonna be doing another one soon. Make sure the connections are fully clamped in place. the top connection closest to the htc/at&t logo on the screen controls the touch, while the bottom connection controls the picture. So just see if the bottom connection is damaged or maybe out of place. If nothing is wrong with them then you may have a faulty screen. I suggest always testing the screen before actually putting everything in place with the adhesives, so just connect it first and if it works then you can reassemble everything.. I'm not too sure whether there is any difference with the htc one x and one xl screen. As far as I know they should be very similar. But I would definitely stay on the safe side and get only the screen that is made for your device. I have not attempted using one with the other.
My wife dropped her phone and shattered the screen, so rather than giving my first born child to have it replaced I did it myself. I replaced the digitizer and everything went fine, I made sure that the connections were snug and secure and that all areas of the screen are responsive. However when I plug it in to charge it, that all changes. While on the charger my touch is almost non existent and when it does sense it, it is very inaccurate or slow. I have tried on my original htc sensation charger with and without its dock. I have also used my wife's new note 2 charger and my hp touchpad's charger and have the same problem on all of them.
Thanks for any help!
Hi go here
http://forum.xda-developers.com/showthread.php?t=1239238
Hit thanks button if you find me helpful
sent from amazing HTC sensation using xda premium
Hi guys,
so i recently broke the screen of my OPO
I bought a screen replacement with frame on ebay.
I tried to replace it myself, one thing i did bad was brake the antenna but i bought a new one
So the screen that i bought worked fine it booted up and touch was working etc. However, when my new antenna came i opened it back up and to put the antenna in.
and now when i boot up the phone the display doesnt work, the lights are powered on at the bottom but the display is black.
I tried disconnecting and reconnecting things and at one point the screen came back but went away again.
So i tried reconnecting each thing one by one and testing the screen as i go a long and the screen was working at a few points but even half assembled the screen doesn't display anything but it is powered on,
faddys123 said:
Hi guys,
so i recently broke the screen of my OPO
I bought a screen replacement with frame on ebay.
I tried to replace it myself, one thing i did bad was brake the antenna but i bought a new one
So the screen that i bought worked fine it booted up and touch was working etc. However, when my new antenna came i opened it back up and to put the antenna in.
and now when i boot up the phone the display doesnt work, the lights are powered on at the bottom but the display is black.
I tried disconnecting and reconnecting things and at one point the screen came back but went away again.
So i tried reconnecting each thing one by one and testing the screen as i go a long and the screen was working at a few points but even half assembled the screen doesn't display anything but it is powered on,
Click to expand...
Click to collapse
Get a refund/return for your display?
Also,can you tell me from where you got the network/signal antenna?
Mr.Ak said:
Get a refund/return for your display?
Also,can you tell me from where you got the network/signal antenna?
Click to expand...
Click to collapse
hey thanks for your reply.
i am getting a refund for it, i hope the next one i buy works.
I bought the antenna from ebay but it seems to be too long
faddys123 said:
hey thanks for your reply.
i am getting a refund for it, i hope the next one i buy works.
I bought the antenna from ebay but it seems to be too long
Click to expand...
Click to collapse
That's sweet! Can you please post a link from where you got the network antenna?