Related
Hey everyone.
I just got a brand-new G-Tablet through Sears. I'm checking here to see if anyone has any ideas before their tech support opens in ~two hours.
I got it to my office, plugged it in and charged it until the light turned green. Then I turned it on and played with it a bit. I didn't have a method to put it on the network right then to sync anything, so I really just poked around and then set it to the side. One thing to note is that I wasn't presented with a setup screen at all, it booted straight to home.
Then later that afternoon when I went to go home, it wouldn't power on. I'm not sure if it went to sleep or powered off, but nothing happens no matter what button combination I press. I've tried just pressing power, holding it down for 4 seconds, holding it down for 30 seconds, power and volume + at the same time, and power and volume - at the same time.
I tried hooking it up to my computer last night, thinking that maybe the display didn't come back from sleep and maybe I could force a reboot via ADB, but it must be off alltogether since it didn't trigger a USB installation on the computer.
When I plug it in to charge, the little light turns red, then a while later turns green, indicating that it is fully charge, yet still no joy.
Your thoughts?
Press the power button for a really long time to see.
Sent from my GT-I9000 using XDA App
Just held it down for 90 seconds, no dice. I tried pressing it briefly afterwards too just in case.
I think Roebeet and a few others had a similar issue. I believe they had to wait 24+ hours for the battery to drain. I can't find the thread but the search button may help
You didn't update the firmware, correct? This is a known issue with the older firmware and it's happened to me.
I believe that the device is frozen - and yes, when it gets in that state you cannot reset it, even when holding down the power button. You have two choices, when this happens:
1- Open up the back of the device (and thus voiding the warranty) and press the reset button on the system board. That will fix it immediately. I know this probably isn't the best option, but I wanted to mention it.
2- Unplug the device and wait for the battery to completely drain. This takes about 24 hours. Once drained, you can press the power button and it will boot up for 10-15 seconds before stopping - that's your queue that the device is "fixed" so you can start re-charging it.
Fortunately, this probably seems to be resolved on newer firmware, tmk. I've only had this happen on a device with the original stock firmware.
The two of you are gentlemen and scholars. I'll let you know how it turns out. I was on the phone to get the RMA when the line went all fuzzy and I couldn't talk to them. Then it did the same thing when I called back. Then I saw this post. Divine Intervention...
Going on 28 hours now and still nothing...I'll probably give it at least 3 days before I send it back.
Give it a few more hours, and then plug it in for a minute and try powering it up. the battery could be so drained at this point that it needs to be plugged in to go on.
Mine took 24 hours to drain, but I wasn't sure if it was at 100% charged, at the time.
Almost to the 48 hours mark and still nothing. I tried plugging it in briefly just to check and the red light still comes on, but it won't power up. Anyone know the possible standby time of a fully charged batter on these things? I was thinking if the system locked up and it isn't hardly doing anything, it could last a while...
Maybe a return to the store you purchased it from at this point. The battery should be dead by now. You should be able to get an exchange or you can try the other route Roebeet suggested but that will definitely void your warranty
thebadfrog said:
Maybe a return to the store you purchased it from at this point. The battery should be dead by now. You should be able to get an exchange or you can try the other route Roebeet suggested but that will definitely void your warranty
Click to expand...
Click to collapse
The problem is that I'm in Guantanamo Bay, Cuba. Shipping time is at least 2 weeks and sears won't do an advance replacement. Neither will the Viewsonic support folks. So I'm either stuck having to buy a second one and waiting for them to get the original back before the refund, or waiting a month or more for a repair...
Are there any seals inside the case that get broken if you open it?
I don't know the answer but this may be of some help
http://forum.xda-developers.com/showthread.php?t=842354
thebadfrog said:
I don't know the answer but this may be of some help
http://forum.xda-developers.com/showthread.php?t=842354
Click to expand...
Click to collapse
I think I'm just going to give it anther day then send it in for repair.
Still nothing. Since its going to be over a month before I get a replacement, I'm just going to return it and wait for the new crop of tablets to come out. Thanks for the help guys.
Sent from my Dell Streak using XDA App
Sorry to hear that. I think the reset button on the board would have worked, but I understand why you wouldn't want to open the device up. We shouldn't have to void our warranty to be able to do a hard reset.
Rhodizzle said:
Still nothing. Since its going to be over a month before I get a replacement, I'm just going to return it and wait for the new crop of tablets to come out. Thanks for the help guys.
Sent from my Dell Streak using XDA App
Click to expand...
Click to collapse
You might try nvflash.... worked on a friends.
GTO777 said:
You might try nvflash.... worked on a friends.
Click to expand...
Click to collapse
But was your friend's responding at all? I get absolutely nothing. the only thing the tablet does is give me a red light when it's charging and a green light when it's done. The power button does nothing and volume down + power does nothing. doesn't nvflash require a connection over USB before it can do anything?
Hey, I got my transformer yesterday, and for some reason this is the 2nd time this has happened, fully charged battery, but the device won't power on. Attempted to plug into power but no dice. Held the power button for 30 seconds, nothing, held the power and volume up and nothing. Yesterday when this happened I plugged it into my computer (Windows) and held the power and up buttons and it turned on though it could have been windows detecting the drivers. Anyone else having this? Any suggestions? I haven't had a chance to test again and see if I can bring it back through that trick yet, but I will. Then I'll try a factory reset and see if it resolves the issue. I would hate it if this is a defective unit, that's for sure esp since they are so backordered. Outside of that I love the device.
naturefreak85 said:
Hey, I got my transformer yesterday, and for some reason this is the 2nd time this has happened, fully charged battery, but the device won't power on. Attempted to plug into power but no dice. Held the power button for 30 seconds, nothing, held the power and volume up and nothing. Yesterday when this happened I plugged it into my computer (Windows) and held the power and up buttons and it turned on though it could have been windows detecting the drivers. Anyone else having this? Any suggestions? I haven't had a chance to test again and see if I can bring it back through that trick yet, but I will. Then I'll try a factory reset and see if it resolves the issue. I would hate it if this is a defective unit, that's for sure esp since they are so backordered. Outside of that I love the device.
Click to expand...
Click to collapse
when your device isnt coming on, does your computer give you a usb notification? You could be putting it in apx mode on accident.
dcmtnbkr said:
when your device isnt coming on, does your computer give you a usb notification? You could be putting it in apx mode on accident.
Click to expand...
Click to collapse
I will find out in a few. The thing is this has happened when I left the device unplugged and in sleep when driving to/from work. Yesterday plugging it back into the computer brought it to life. Nothing else did. Not sure what apx mode is even.
Sent from my MB860
EDIT: Ok, turns out it get stuck in some weird power mode. I plugged it into the computer with no resolution, when I held the power button for 10 seconds, then waited 5 and pressed it again, the device powered on. I suspect it might be an issue involving detecting WiFi access points when driving or something else. I'll Factory Restore and see what happens.
try turning off screen lock.
naturefreak85 said:
I will find out in a few. The thing is this has happened when I left the device unplugged and in sleep when driving to/from work. Yesterday plugging it back into the computer brought it to life. Nothing else did. Not sure what apx mode is even.
Sent from my MB860
EDIT: Ok, turns out it get stuck in some weird power mode. I plugged it into the computer with no resolution, when I held the power button for 10 seconds, then waited 5 and pressed it again, the device powered on. I suspect it might be an issue involving detecting WiFi access points when driving or something else. I'll Factory Restore and see what happens.
Click to expand...
Click to collapse
I had that sometimes in the first day I had it, after that it hasn't happened. No factory reset, just make sure to do a hard shutdown (powerbutton 10 sec~) while it's booted and it should fix the issue.
seshmaru said:
I had that sometimes in the first day I had it, after that it hasn't happened. No factory reset, just make sure to do a hard shutdown (powerbutton 10 sec~) while it's booted and it should fix the issue.
Click to expand...
Click to collapse
Yea, it had happened once already, and again. I'll be testing today when I leave work, factory reset and see what happens. Should it continue, I'll go to the next step. I'm just not sure what it is. Interesting bug to say the least.
naturefreak85 said:
I will find out in a few. The thing is this has happened when I left the device unplugged and in sleep when driving to/from work. Yesterday plugging it back into the computer brought it to life. Nothing else did. Not sure what apx mode is even.
Sent from my MB860
EDIT: Ok, turns out it get stuck in some weird power mode. I plugged it into the computer with no resolution, when I held the power button for 10 seconds, then waited 5 and pressed it again, the device powered on. I suspect it might be an issue involving detecting WiFi access points when driving or something else. I'll Factory Restore and see what happens.
Click to expand...
Click to collapse
From the way you are describing getting it to work again, it sounds like you were in apx mode...
dcmtnbkr said:
From the way you are describing getting it to work again, it sounds like you were in apx mode...
Click to expand...
Click to collapse
I still don't really know what APX mode is, from the limited things I have seen about it, in order to get into such, the device has to be powered off first. As far as I can tell, my device isn't randomly powering itself off and automatically going into APX mode. This happens without me touching the device. When I did the power off and on today, it wasn't plugged into the computer at all. There was no recognition from the computer that the device was plugged in.
Well as of today, my EEE Transformer is dead. Will not power on the screen, Asus offers a repair of 14 business days, unacceptable.
Powering on issue
Woah...I was scared to death when mine didn't turn on the next morning that I got the device. Charged it for an hour and try to turn on again, nothing.
Holding the buttons several different ways that I know how to reset it didn't work. Finally I held the button down for more than 10 seconds. Wait a few seconds, then it powered on. Why didn't they make a hard reset since you can't remove battery!??? Hope this is just some fluke and could be updated with firmware.
nxp3 said:
Woah...I was scared to death when mine didn't turn on the next morning that I got the device. Charged it for an hour and try to turn on again, nothing.
Holding the buttons several different ways that I know how to reset it didn't work. Finally I held the button down for more than 10 seconds. Wait a few seconds, then it powered on. Why didn't they make a hard reset since you can't remove battery!??? Hope this is just some fluke and could be updated with firmware.
Click to expand...
Click to collapse
Alas, mine didn't get resolved with that, computer detects it now, but no screen response. Asus tells me 14 business days to fix then says try to restore it with the Kernel Source Code. Unfortunately I can't see a way to do such from the folder and they decided to disconnect me.
There is a bug with the default lock screen that makes it so the screen doesnt power on occasionally. In order to work around this you need to disable the lock screen in the settings, or change it from the default one.
Obviously in order to do this initially it needs to be powered on and so you can see it. Therein lies your problem of course. To get around this, charge up your device so you know it has power, use the force power off method (10-12 second press of the power button), wait a few seconds (30+), then power on the device normally (5-6 second press of the power button).
If your screen doesnt come on after that, try a couple more times. It really is an RMA job if it continues to fail. If it does come on, let it boot up to the lock screen, and dont let the screen go off, keep it 'alive', unlock the device and change the lock screen in the options, to either be switched off, or to anything other than default.
This wont work for everyone, as obviously a few may actually have duff screens, but for some of you, it may just be the lock screen bug you are getting unlucky with.
Yea, I seem to have not only the lock screen bug but a defective screen. Unacceptable to me, but hey, what can I do? I've been disconnected 5 times so far, waiting on a manager and will be requesting a faster resolution than what they are offering me. (10-14 Business days is unacceptable)
stuntdouble said:
There is a bug with the default lock screen that makes it so the screen doesnt power on occasionally. In order to work around this you need to disable the lock screen in the settings, or change it from the default one.
Obviously in order to do this initially it needs to be powered on and so you can see it. Therein lies your problem of course. To get around this, charge up your device so you know it has power, use the force power off method (10-12 second press of the power button), wait a few seconds (30+), then power on the device normally (5-6 second press of the power button).
If your screen doesnt come on after that, try a couple more times. It really is an RMA job if it continues to fail. If it does come on, let it boot up to the lock screen, and dont let the screen go off, keep it 'alive', unlock the device and change the lock screen in the options, to either be switched off, or to anything other than default.
This wont work for everyone, as obviously a few may actually have duff screens, but for some of you, it may just be the lock screen bug you are getting unlucky with.
Click to expand...
Click to collapse
naturefreak85 said:
Yea, I seem to have not only the lock screen bug but a defective screen. Unacceptable to me, but hey, what can I do? I've been disconnected 5 times so far, waiting on a manager and will be requesting a faster resolution than what they are offering me. (10-14 Business days is unacceptable)
Click to expand...
Click to collapse
i am in the same boat as you, luckly i picked up the acer for the weekend because i didnt think i was going to get the asus. glad i did
I'm waiting on hold with Asus to see if they will do an Advance Repair, basically I get put on the line for the full price of the device until they declare mine broken since the return period on the Acer is 14 days at best buy. Quite outside of the repair period.
kenshin0088 said:
i am in the same boat as you, luckly i picked up the acer for the weekend because i didnt think i was going to get the asus. glad i did
Click to expand...
Click to collapse
what is the number you are calling, when i called they had almost no idea what i was talking about. they kept asking me if when i am pluged into the wall if thre was a light on the chager when there is no light lol i think they thot i had a laptop or netbook
18886783688 Option 2 Option 2 Option 5
kenshin0088 said:
what is the number you are calling, when i called they had almost no idea what i was talking about. they kept asking me if when i am pluged into the wall if thre was a light on the chager when there is no light lol i think they thot i had a laptop or netbook
Click to expand...
Click to collapse
did you find out anythinig from asus?
kenshin0088 said:
did you find out anythinig from asus?
Click to expand...
Click to collapse
Had to escalate it up to management and expressed I wanted an advance repair and was willing to give them my credit card number so they could place a hold on the card for the amount of a replacement until they got mine. Has to be escalated above the rep should hear back in a couple hours. If not I have an extension and will call back
Sent from my MB860
they are having me download the source code and try and force it to the transformer we will see if it works will report back
Hello!
I just received my Infinity and started working on it, since there was a new Firmware available I downloaded and installed it.
When done it said "shutting down" and turned the Infinity off.
And this is were the trouble began .. since the last few hours I am trying to get it to work again but nothing seems to work.
Pressing the reset button with a paperclick won't work.
Volume down + Power only lets the Tablet vibrate after 10-12 seconds
Pressing power for 20 seconds (ASUS suggested this..) does the same thing.
with/without A/C Charger or docking station same thing, I get absolutely nothing on the screen.
When plugging it in via USB I get the APX mode.
Is there anything I can do at all? I don't want to send it back of course and thought APX Mode will maybe help me install and / fix something "blind" since I think the issue might be related to the Firmware upgrade..
Thanks in advance
Read this thread [How-To] All-In-One Guide For Asus Infinity (TF700) [24/09/2012] if you haven't already and you should be able to fix it.
Cheers Q
Quozl said:
Read this thread [How-To] All-In-One Guide For Asus Infinity (TF700) [24/09/2012] if you haven't already and you should be able to fix it.
Cheers Q
Click to expand...
Click to collapse
I did try the button combinations, and for NVFlash it says: THIS REQUIRES A NON-BRICKED AND UNLOCKED DEVICE. IT WON'T WORK ON ALREADY BRICKED DEVICES
Well.. I think mine already could be bricked, and I can't unlock it by installing the apk
If pressing Volume Down +Power only give you a black screen and not even the Asus logo it means you are bricked (could also be a hw failure, who knows) ... APX mode is useless for your device. So if u can't manage to boot into recovery or in fastboot mode i would recommend you to start the RMA process.
Pretoriano80 said:
If pressing Volume Down +Power only give you a black screen and not even the Asus logo it means you are bricked (could also be a hw failure, who knows) ... APX mode is useless for your device. So if u can't manage to boot into recovery or in fastboot mode i would recommend you to start the RMA process.
Click to expand...
Click to collapse
Nope nothing, doesn't matter if I press up/down + power for how long all I get is a 1 second vibrate after 10-12 seconds, with or without the Volume keys.
Pad is charged, same with A/C, when I try without the LED next to the power doesn't even turn on
Pressing the reset with a paperclip won't work either as stated so I guess it really is a brick...
How can a official Firmware Upgrade brick a device? I'm not new to Android and already own 3 HTC's all rooted and stuff but I never came across something like this ..
A few Things you can still try to recover the Infinty
Dude, that absolutely SUCKS! I would be so disappointed / angry if I were in your position, especially having the tablet for a short time. It DOES sound like a hardware failure (video seems out, but it's almost as if the tablet is running dark, and you just have no video. Can you return it to the retailer you bought it from? That would be 1000% better than an RMA, which is another thing that Asus does extremely poorly (They use a 3rd Part servive out of Grapevine Texas, and in MOST cases it is a nightmare. I don't understand why you can't bring/send it back to the point of purchase. You are not requesting arefund, just exchange for defective tblet.
As a last resort, do this: RUN THE BATTERY FULLY DOWN. Do not put the charge on, and keep checking if the tablet is powered on (touch the power button quickly, like you are taking it out of sleep mode. This could take the better part of a full day/night, but if you run it until the battery fully discharges, I remember a Prime user that this saved the day. It certainly is worth the effort, considering the alternatives.
Once it fully runs down, plug in the charger, and it should power up / begin charging and you will know in two seconds if it worked cause that Asus Logo will be the greatest site you will have seen in some time.
Oh, and something you can try before beginning that long process: I know you have already tried most reset methods, but humor me and put a pin in the reset hole - by HDMI, but instead of just pressing it briefly, press and hold for a FULL 30 + seconds. Some swear this changes the parameters, thiugh I am doubrtfull. More significant was mention that while holding the microswitch in, there is a "draining" happening of the memory onboard. I half belive it because years ago, I had an old HP Jornada Pocket PC, and one of the recovery procedures was remove the backup battery, and wait some inutes for a drain of memory to occur. You could SEE the LCD fading, like losing contrast super slowly. When it went completely blank was whenI was instructed to re-power up.
So try the reset pinhole for 30+ seconds
failing that, try a full battery drain
failing that try to return to point of sale
failing that do a shudder RMA with Asus. (Reach out to Gary Key - his PM and Email are listed in these forums. That way at least you will have a point of contact, and he may provide you with others. Good luck I feel for ya, especially with JB almost upon us! :cyclops:
Yosaku said:
Nope nothing, doesn't matter if I press up/down + power for how long all I get is a 1 second vibrate after 10-12 seconds, with or without the Volume keys.
Pad is charged, same with A/C, when I try without the LED next to the power doesn't even turn on
Pressing the reset with a paperclip won't work either as stated so I guess it really is a brick...
How can a official Firmware Upgrade brick a device? I'm not new to Android and already own 3 HTC's all rooted and stuff but I never came across something like this ..
Click to expand...
Click to collapse
Your are not the only one, afaik other users bricked their devices just by updaing with official firmware.However i'm a bit confused about that "shutting down" message and iirc the device only does a "restart" when updating,it doesn't shutdown.
Hi!
Thanks for the long reply
I tried holding the reset for more than 30 seconds, as I thought it did not help.
Any Tipps on how to drain the battery if I can't even turn it on? It vibrates after 10 seconds but I don't think that will drain much of the battery..
As for the RMA:
I won't do it via ASUS, they told me to but hell no.
Bought it from Amazon and already contacted them, I'll send it back when I get the confirmation they won't do an ASUS RMA, if they do want I just get my money back and buy a new one lol. Either way it is faster than Asus..
/edit
I wondered about the shutdown too and even waited quite some time after it went black because I thought it would boot back again, but well.. it did not
Thanks again!
Yosaku said:
Hi!
Thanks for the long reply
I tried holding the reset for more than 30 seconds, as I thought it did not help.
Any Tipps on how to drain the battery if I can't even turn it on? It vibrates after 10 seconds but I don't think that will drain much of the battery..
As for the RMA:
I won't do it via ASUS, they told me to but hell no.
Bought it from Amazon and already contacted them, I'll send it back when I get the confirmation they won't do an ASUS RMA, if they do want I just get my money back and buy a new one lol. Either way it is faster than Asus..
Thanks again!
Click to expand...
Click to collapse
Put it in APX mode and it will drain your battery.Btw are you sure the battery was charged enough when you updated?
Yosaku said:
Hi!
Thanks for the long reply
I tried holding the reset for more than 30 seconds, as I thought it did not help.
Any Tipps on how to drain the battery if I can't even turn it on? It vibrates after 10 seconds but I don't think that will drain much of the battery..
As for the RMA:
I won't do it via ASUS, they told me to but hell no.
Bought it from Amazon and already contacted them, I'll send it back when I get the confirmation they won't do an ASUS RMA, if they do want I just get my money back and buy a new one lol. Either way it is faster than Asus..
Thanks again!
Click to expand...
Click to collapse
I will try to find the thread - but check in the Prime threads - search for screen black, no video etc. The guy(s) that did it said that they just kept turning it on.. or touching the power switch - I know that's not too detailed. Here's the thing: a vibrate is what the tablet does NORMALLY when powering up... I think your may be running, you just can't see it. The only clues you can get are from the LED in the power button. Green means something like 95% charged. Amber means less that 14% and blinking amber (with no power supply attached means it is within the last few percent - Those are ballpark figures, you can find the full LED color descriptions with a bit of searching. Anyway it is you only indicator so, finding out waht the colors mean might help you in the discharging process.
Pretoriano80 said:
Put it in APX mode and it will drain your battery.Btw are you sure the battery was charged enough when you updated?
Click to expand...
Click to collapse
EDIT: JUST NOTICED you said this is from Amazon. If that's the case, you have no worries. Amazon replaces items faster/better than any other retailer. In fact Amazon will cross ship you a new one and you can return this after receiving the new one - at least that's how they did it with my TF101... two times. On the third exchange, they try to refund you and make you purchase it again, but I complained that it was not the SAME problem each time (this was on the docks) and they went ahead and sent me a 3rd one. Just go ahead and do that. You probably would be better off with a different one, but check it CAREFULLY for defects. I am convinced that these are near impossible for Asus to build without screwing up something - Screen separation (viewed from the edge), scratches, poor cutout/application of the Logo (My daughter actually bled from a cut it gave he -sharp edges) and the INFAMOUS Loose Screen, "Clicking" sound - squeeze the tablet gently all the way around. if it clicks or makes any grinding noises return it. For $500 any defect is unacceptable. Good luck!
Good idea. I also wondered about his state of charge while updating...
Pretoriano80 said:
Put it in APX mode and it will drain your battery.Btw are you sure the battery was charged enough when you updated?
Click to expand...
Click to collapse
Yes, it was even plugged in
SmartAs$Phone said:
I will try to find the thread - but check in the Prime threads - search for screen black, no video etc. The guy(s) that did it said that they just kept turning it on.. or touching the power switch - I know that's not too detailed. Here's the thing: a vibrate is what the tablet does NORMALLY when powering up... I think your may be running, you just can't see it. The only clues you can get are from the LED in the power button. Green means something like 95% charged. Amber means less that 14% and blinking amber (with no power supply attached means it is within the last few percent - Those are ballpark figures, you can find the full LED color descriptions with a bit of searching. Anyway it is you only indicator so, finding out waht the colors mean might help you in the discharging process.
Good idea. I also wondered about his state of charge while updating...
Click to expand...
Click to collapse
Thing is, even when it vibrates the LED is always off, only when I plug it in for charging it turns orange.
I will try the APX method Just plug it in to the PC and when the "can't find driver" message pops up it's in APX? Or do I have to install the drivers first?
Yosaku said:
Yes, it was even plugged in
Thing is, even when it vibrates the LED is always off, only when I plug it in for charging it turns orange.
I will try the APX method Just plug it in to the PC and when the "can't find driver" message pops up it's in APX? Or do I have to install the drivers first?
Click to expand...
Click to collapse
You don't need the PC at all, just put it in APX mode and let it be. The led turns on only when you plug the charger.
Edit: btw, you will know if it's in APX mode because even if the screen is off the device will get warm.
Pretoriano80 said:
You don't need the PC at all, just put it in APX mode and let it be. The led turns on only when you plug the charger.
Click to expand...
Click to collapse
Oh ok, since the only thing it does is vibrate I don't know if it is in APX Mode .. and it vibrates not after 5 seconds even when I press the volume up, but after ~10 seconds
Yosaku said:
Oh ok, since the only thing it does is vibrate I don't know if it is in APX Mode .. and it vibrates not after 5 seconds even when I press the volume up, but after ~10 seconds
Click to expand...
Click to collapse
Indeed it takes 10 seconds before it gets in APX mode.
Pretoriano80 said:
Indeed it takes 10 seconds before it gets in APX mode.
Click to expand...
Click to collapse
Ok .. I think it is in APX now ... I need to head out for a few hours anyway so wish me luck!
And thanks for your help so far
Maybe that is why they pushed the release back. Because they found it was bricking devices, lol. That sucks, tho, man. Good thing you bought it recently enough to send it back with Amazon. I wouldn't even bother with anything else and just sent it back.
Maybe....you could see what's going on if you connected it to the TV/Monitor on the HDMI port....
Soo I'm back!
It is still vibrating, so the battery is not empty yet ;(
I thought about the HDMI too but I don't have a mini-HDMI adapter.
Anyway it is Saturday and I might send it back today ... although I am usually not giving up till I fix something I guess their might be nothing else left.
Thanks so much for your support so far
SmartAs$Phone said:
if it clicks or makes any grinding noises return it. For $500 any defect is unacceptable. Good luck!
Click to expand...
Click to collapse
500$ ?? Wow ... I am actually thinking about getting one from the US! These things cost around 900$ with Dockingstation in Germany .. way to rip off people oO
Getting off Topic I know, just wanted to mention
Yosaku said:
Soo I'm back!
It is still vibrating, so the battery is not empty yet ;(
I thought about the HDMI too but I don't have a mini-HDMI adapter.
Anyway it is Saturday and I might send it back today ... although I am usually not giving up till I fix something I guess their might be nothing else left.
Thanks so much for your support so far
Click to expand...
Click to collapse
Ok another trick and it involves some luck. IF its on and you power it off you get a very,very short vibration (it's hard to feel it sometimes) and then you normally see a confirmation box appear in the middle of the screen asking you "Would you like to shut down?". Then you either tap Cancel or OK. Using your "minds eye" try to imagine where that box is on that black screen and tap it where you would to answer the question "OK". If you have any luck the damn thing will shut off and in ~8 seconds you'll feel a longer vibration indicating it turned off. Then DO NOT turn it on. Instead plug in the power adapter and let it power on and see if that puts your video back up.
I'm just wondering if the cable to the screen inside has popped off the main board. I know i've read about that happening but it usually occurs after a pretty good jolt to the unit.
My phone: Nexus S, 16Gb, Rom CM11, Android 4.4.4 (List of updates: https://download.cyanogenmod.org/?device=crespo)
My story
Yesterday, (about 9.00pm 13/12/2015) my phone got some laggy, so I powered him off. I left it there, 15 minutes later I came back, and I forgot that he had been powered off, so I thought it was just sleeping. I picked him up and press PowerButton. Nothing happended!
Then I got a look at CM rom, found that interesting is my Rom just got a new update at 2.00pm 13/12/2015. I think that my phone has auto-updated!!
In the past, sometime he behaved the same: PowerButton not respond. So, after that 1st press, about 5 sec later, I started to press the PowerButton repeatedly and rapidly, hopefully the phone would wake up.
But no, the reality was that he was being off. There were about 6-7 presses, I will describe slowly below (assume between each press is 0.2 sec):
1st and 2nd press: nothing happened
3rd press: the phone vibrated, and Google logo appeared
4th press: (I had no mean to continue pressing, but it was too fast, I couldn't stop) suddenly, the Google logo disappeared (so the logo stayed on screen just for about 0.2 sec; while normally, it should stay there for atleast 5 sec)
5th and 6th press: nothing happened!
And from then on, no more, anything happened.
What I tried
Hold PowerButton for even 1 minute: nothing happen!
Hold PowerButton + VolumeUP for even 1 minute: none!
Hold PowerButton + VolumeUPandDOWN for even 1 minute: none too!
Connect to charger (wall or pc): no Battery Animation show up! BUT the phone and Battery get warming up!
Take out the Battery for even 15 minutes, then put it back, and PowerButton: nothing!
And the phone not get recognized by PC too.
Sumary
No display
No vigration
No recognized by PC (because of this, I can not follow this method: http://forum.xda-developers.com/oneplus-one/general/guide-unbrick-oneplus-one-t3013732
More Information
In the past, the VolumeDOWN sometimes seems get stucked, cause the phone silent and auto boot to safemode, after many try to press and reboot, the phone may get out of safemode (because VolumeDOWN back to normal)
PowerButton sometimes not respond.
My Battery is not good, sometimes it drops too much! Eg: having 50%, after reboot, dropped to 3%, and start to increase slowly, max around 30% and become normally.
Hope you guys have some ideas! I still can't do anything, when the phone is not regconized by PC!!
Thanks for reading!
Thank you!
Hey,
2 things come to mind and I bet are both the problems. First off you need a new battery and you seem to know this, very cheap now a days but still buy a good one as cheap knock offs are abundant and don't support the power they say, try mugen, anker or stock oem
Also you need to replace power button, this phone was always notorious with bad ones, a new one is cheap but many often found just a loose connection so if you open up the phone, check the ribbon connections and then throw in that new battery all should be well, hopefully
Best of luck!
demkantor said:
Hey,
2 things come to mind and I bet are both the problems. First off you need a new battery and you seem to know this, very cheap now a days but still buy a good one as cheap knock offs are abundant and don't support the power they say, try mugen, anker or stock oem
Also you need to replace power button, this phone was always notorious with bad ones, a new one is cheap but many often found just a loose connection so if you open up the phone, check the ribbon connections and then throw in that new battery all should be well, hopefully
Best of luck!
Click to expand...
Click to collapse
Thank you. I'll try your suggest ASAP.
But I'm wondering, that do you think that CM Update maybe also a reason?
I kind of doubt it as that should only effect the software, if you were getting a bootloop or anything to that extant yeah, but being it won't power on at all I doubt it
thank you
Nope, I've seen these symptoms before - exactly the same thing. Dude, I think your phone is Superbricked.
I've got a stack of 3 Nexus S 4G's that have exactly the same problem - the eMMC card is trashed by a buggy "secure erase" implementation. See: https://wiki.cyanogenmod.org/w/EMMC_Bugs
My "working" one was working great, even set it up to sell on eBay, when I went to wipe its data with a factory-reset from the settings menus. When it shut down to reboot, I pulled the battery. That's what bricked it - because the eMMC was halfway through a background erase/rewrite procedure, it wiped out the boot loader somehow and completely bricked the phone. It now does precisely, exactly the same thing you describe - absolutely nothing, except when it's plugged in, it warms up after a while.
Best I can tell, the only way out from here is to use a JTAG device to reflash the chip, but even then, the eMMC itself might be "unbootable" (i.e. can't start up, can't be read or written, can't be reformatted/restored).
I just called it "end of life" for those phones and now they're just a sour reminder on my shelf
FalconFour said:
Nope, I've seen these symptoms before - exactly the same thing. Dude, I think your phone is Superbricked.
I've got a stack of 3 Nexus S 4G's that have exactly the same problem - the eMMC card is trashed by a buggy "secure erase" implementation. See:
My "working" one was working great, even set it up to sell on eBay, when I went to wipe its data with a factory-reset from the settings menus. When it shut down to reboot, I pulled the battery. That's what bricked it - because the eMMC was halfway through a background erase/rewrite procedure, it wiped out the boot loader somehow and completely bricked the phone. It now does precisely, exactly the same thing you describe - absolutely nothing, except when it's plugged in, it warms up after a while.
Best I can tell, the only way out from here is to use a JTAG device[/URL] to reflash the chip, but even then, the eMMC itself might be "unbootable" (i.e. can't start up, can't be read or written, can't be reformatted/restored).
I just called it "end of life" for those phones and now they're just a sour reminder on my shelf
Click to expand...
Click to collapse
thank you!!
my heart just stop breathing :'( :'(
God, I wish there were a solution to it. I'd really like to donate a phone to anyone that thinks they have the tools or skills to make a "how I did it" explanation - involving whatever tools/software are necessary - to bring these phones back and help us all. I bought 2 of those 3 phones as "for parts" on eBay, and it turned out that both of those phones appeared to have exactly this same issue (though one also had a cracked glass). I even verified the issue by swapping in my good phone's eMMC (at least on the NS4G, it's a swappable card module), and the boards booted up. I only needed the one for the good screen (as I had a good board but completely destroyed display panel) - and that's how I got my one working again.
Then, in the end, I accidentally stumbled upon the method by which the previous two phones were bricked - and now there are three. It seems like a fairly common problem. :/
Hi,
I think I have bricked my S7.
Yesterday I installed Superman Rom and everything was working fine until this afternoon.
I played a bit around and somehow my S7 got stuck and it seemed like i messed something up. I was in some kind of bootloop so i flashed everything new -Bootlaoder, Modem and Superman Rom.
Now I have a black screen and the LED is light up in blue.
I can't do anything. Tried to restart with Home Vol- and Power key but it doesn't work.
If I connect it to the Computer it won't be recognized.
Strange thing is, if I press the Power Key the computer recognizes Exynos8890 in the device manager, but only if I keep pressing the power key.
As soon as I release the power key the computer recognizes nothing...
Does anyone have an idea?
Try holding Volume Down & Home & Power until the phone reboots twice, keep the buttons pressed for 2 full reboots, and hopefully the 2nd one will get you back into download mode
Thank you for your help!
I tried that but it doesn't work.
It's strange because I can do what I want and nothing happens.
Black screen and blue light. It doens't even turn off or reboot...
Only thing what happens is that exynos8890 appears in the device manager as long as I keep pressing the power button.
Same problem as me?
http://forum.xda-developers.com/galaxy-s7/help/boot-loop-bricked-t3499109/post69596073#post69596073
Sounds different.
Because you are able to get into recovery and download. I'm not able to do that
alexx3333 said:
Sounds different.
Because you are able to get into recovery and download. I'm not able to do that
Click to expand...
Click to collapse
How long are you holding the button combination for?
Try 30 seconds+
I tried for several minutes, but the phone doesn't do anything.
I can only think you'll need to wait until the battery runs out, the phone shuts off, then when you charge it again, try the download mode button combo when you power it back on
Ok thank you.
I thought the same.
Unfortunately the battery was at 90% so I think it will take a few days/weeks until it dies...
alexx3333 said:
Ok thank you.
I thought the same.
Unfortunately the battery was at 90% so I think it will take a few days/weeks until it dies...
Click to expand...
Click to collapse
Connect the white Micro > Normal USB adapter that came with the phone to the MicroUSB port, and connect a power hungry USB device to it, I just tried with a USB desk fan and the phone powered it on spinning
That will drain the battery quickly
Great idea but it doesn't seem to work.
Looks like I have no power in the USB connection.
Seems like the phone is totaly frozen.
Ok so how it looks at the moment, my only choiches are wait several days until the battery dies (don't know how long this will take) or sending it to Samsung for a repair.
Thank you for your help!
Good luck, if I think of anything else I'll reply here, hope you get it sorted
EDIT - Did you try holding the power button while you had the USB device connected, to see if it provides USB power then?
Wow, the exact same thing literally happened to me yesterday.
I wasn't doing anything to the phone - it's completely stock and unrooted, and I wasn't messing with anything. At the time it happened, I scrolling through the task switcher when all of the screenshots of running apps suddenly became white squares. I tried pressing the home button but it didn't respond (though I could still scroll fluidly through the white squares). A few seconds later the screen went black and that was it. Dead dead dead. Totally bricked. The only response I can get is "Exynos8890" in the Device Manager when holding the power button, just like you.
This really sucks because I paid full cash and imported an international version, so I have no warranty. I'm off to the Samsung store to plead with them about honoring the warranty anyway, maybe if I offer some cash on top.
I suspect the storage chip failed. Yesterday before it died, I was downloading all of my images off of the SD card to organize them, and I noticed that about 5% of them failed to copy due to an unknown I/O error. Of course I assumed this was a corrupt SD card, not internal storage. I did manage to pull them all off (though some were damaged) through a combination of adb shell, dd, and adb pull. During the process the phone hard-locked a few times, but each time I was able to reboot via the VolDown+Power combo.
When the phone finally died for good, it was several hours after I had finished copying the photos and since hte last reboot. It had been working perfectly since then - I was browsing reddit, watching netflix, etc. However, given that I got the white squares in the task switcher right before it kicked the bucket, I think the internal storage was actually to blame, not the SD card. The white squares indicates that it was trying to fetch the screenshots off the disk and failing.
It's very odd that I cannot find any other instance of this kind of failure on the internet except this one thread, which happened on the exact same day that my phone died. Very strange.
*Detection* said:
Good luck, if I think of anything else I'll reply here, hope you get it sorted
EDIT - Did you try holding the power button while you had the USB device connected, to see if it provides USB power then?
Click to expand...
Click to collapse
Yes I have tried that but no power at all...
stoanhart said:
Wow, the exact same thing literally happened to me yesterday.
I wasn't doing anything to the phone - it's completely stock and unrooted, and I wasn't messing with anything. At the time it happened, I scrolling through the task switcher when all of the screenshots of running apps suddenly became white squares. I tried pressing the home button but it didn't respond (though I could still scroll fluidly through the white squares). A few seconds later the screen went black and that was it. Dead dead dead. Totally bricked. The only response I can get is "Exynos8890" in the Device Manager when holding the power button, just like you.
This really sucks because I paid full cash and imported an international version, so I have no warranty. I'm off to the Samsung store to plead with them about honoring the warranty anyway, maybe if I offer some cash on top.
I suspect the storage chip failed. Yesterday before it died, I was downloading all of my images off of the SD card to organize them, and I noticed that about 5% of them failed to copy due to an unknown I/O error. Of course I assumed this was a corrupt SD card, not internal storage. I did manage to pull them all off (though some were damaged) through a combination of adb shell, dd, and adb pull. During the process the phone hard-locked a few times, but each time I was able to reboot via the VolDown+Power combo.
When the phone finally died for good, it was several hours after I had finished copying the photos and since hte last reboot. It had been working perfectly since then - I was browsing reddit, watching netflix, etc. However, given that I got the white squares in the task switcher right before it kicked the bucket, I think the internal storage was actually to blame, not the SD card. The white squares indicates that it was trying to fetch the screenshots off the disk and failing.
It's very odd that I cannot find any other instance of this kind of failure on the internet except this one thread, which happened on the exact same day that my phone died. Very strange.
Click to expand...
Click to collapse
That sounds exactly like my Problem.
A faulty storage chip would also explain my Problems before the phone died for good.
The day my phone died I had some Problems. The phone was frozen from time to time until it got into the bootloop, but I thought I messed something up in the Rom because I did a lot of testing and the Combo also did work.
After reflashing the Rom everything seemed to be fine first until it died for good.
Yes it's strange, I also didn't find anything similar on the Internet.
I have learned my phone is from Nigeria. This should be a fun RMA process. FML
stoanhart said:
I have learned my phone is from Nigeria. This should be a fun RMA process. FML
Click to expand...
Click to collapse
Contact Samsung on twitter, unlikely they'll force you to RMA to Nigeria, they'll have service centres in your region
I managed to get Samsung Canada to refer me to a local service center. I drove 1.5 hours to go there today, the dude plugs it into a charger, and the damn thing just lights up like nothing ever happened. Now it's working fine, but I swear this thing was fully bricked before. The battery still had 73% charge when it came back alive...
I'm happy it's working now, but I'm worried it's just going to crap out again at any time.
Update: after the phone revived itself, it worked pretty well for a week. It locked up a few times, but I was able to reboot each time.
But, after a week, it hard-froze again. This time, it happened to be on charge while it froze so the green LED was on. It's been completely unresponsive for 2.5 weeks now, off charger, with the green LED on. I keep waiting for the LED to drain the battery, but it's taking forever. I'm losing hope that it will recover this time. I guess I'll re-start the process of getting in touch with Samsung, or alternatively, look for a replacement motherboard on eBay.
Does anyone know if the G930F motherboard fits into the G930FD body? I don't actually care about dual sim, but I'm concerned the SIM tray/slot won't work with the G930F motherboard.
Update:
so in the meantime the battery of my s7 died but that didn't change anything. I wasn't able to charge it after that so now it was completely dead.
So I contacted Sasmsung.
They replaced the motherboard and the USB connector on warranty.
Seems like it really was a hardware issue...
alexx3333 said:
Update:
so in the meantime the battery of my s7 died but that didn't change anything. I wasn't able to charge it after that so now it was completely dead.
So I contacted Sasmsung.
They replaced the motherboard and the USB connector on warranty.
Seems like it really was a hardware issue...
Click to expand...
Click to collapse
Hi,
Do you need Proof of Purchase for the warranty?
Thanks.