Database Info

[Q] Brand New G-Tablet, powered on once

Hey everyone.
I just got a brand-new G-Tablet through Sears. I'm checking here to see if anyone has any ideas before their tech support opens in ~two hours.
I got it to my office, plugged it in and charged it until the light turned green. Then I turned it on and played with it a bit. I didn't have a method to put it on the network right then to sync anything, so I really just poked around and then set it to the side. One thing to note is that I wasn't presented with a setup screen at all, it booted straight to home.
Then later that afternoon when I went to go home, it wouldn't power on. I'm not sure if it went to sleep or powered off, but nothing happens no matter what button combination I press. I've tried just pressing power, holding it down for 4 seconds, holding it down for 30 seconds, power and volume + at the same time, and power and volume - at the same time.
I tried hooking it up to my computer last night, thinking that maybe the display didn't come back from sleep and maybe I could force a reboot via ADB, but it must be off alltogether since it didn't trigger a USB installation on the computer.
When I plug it in to charge, the little light turns red, then a while later turns green, indicating that it is fully charge, yet still no joy.
Your thoughts?

Press the power button for a really long time to see.
Sent from my GT-I9000 using XDA App

Just held it down for 90 seconds, no dice. I tried pressing it briefly afterwards too just in case.

I think Roebeet and a few others had a similar issue. I believe they had to wait 24+ hours for the battery to drain. I can't find the thread but the search button may help

You didn't update the firmware, correct? This is a known issue with the older firmware and it's happened to me.
I believe that the device is frozen - and yes, when it gets in that state you cannot reset it, even when holding down the power button. You have two choices, when this happens:
1- Open up the back of the device (and thus voiding the warranty) and press the reset button on the system board. That will fix it immediately. I know this probably isn't the best option, but I wanted to mention it.
2- Unplug the device and wait for the battery to completely drain. This takes about 24 hours. Once drained, you can press the power button and it will boot up for 10-15 seconds before stopping - that's your queue that the device is "fixed" so you can start re-charging it.
Fortunately, this probably seems to be resolved on newer firmware, tmk. I've only had this happen on a device with the original stock firmware.

The two of you are gentlemen and scholars. I'll let you know how it turns out. I was on the phone to get the RMA when the line went all fuzzy and I couldn't talk to them. Then it did the same thing when I called back. Then I saw this post. Divine Intervention...

Going on 28 hours now and still nothing...I'll probably give it at least 3 days before I send it back.

Give it a few more hours, and then plug it in for a minute and try powering it up. the battery could be so drained at this point that it needs to be plugged in to go on.
Mine took 24 hours to drain, but I wasn't sure if it was at 100% charged, at the time.

Almost to the 48 hours mark and still nothing. I tried plugging it in briefly just to check and the red light still comes on, but it won't power up. Anyone know the possible standby time of a fully charged batter on these things? I was thinking if the system locked up and it isn't hardly doing anything, it could last a while...

Maybe a return to the store you purchased it from at this point. The battery should be dead by now. You should be able to get an exchange or you can try the other route Roebeet suggested but that will definitely void your warranty

thebadfrog said:
Maybe a return to the store you purchased it from at this point. The battery should be dead by now. You should be able to get an exchange or you can try the other route Roebeet suggested but that will definitely void your warranty
Click to expand...
Click to collapse
The problem is that I'm in Guantanamo Bay, Cuba. Shipping time is at least 2 weeks and sears won't do an advance replacement. Neither will the Viewsonic support folks. So I'm either stuck having to buy a second one and waiting for them to get the original back before the refund, or waiting a month or more for a repair...
Are there any seals inside the case that get broken if you open it?

I don't know the answer but this may be of some help
http://forum.xda-developers.com/showthread.php?t=842354

thebadfrog said:
I don't know the answer but this may be of some help
http://forum.xda-developers.com/showthread.php?t=842354
Click to expand...
Click to collapse
I think I'm just going to give it anther day then send it in for repair.

Still nothing. Since its going to be over a month before I get a replacement, I'm just going to return it and wait for the new crop of tablets to come out. Thanks for the help guys.
Sent from my Dell Streak using XDA App

Sorry to hear that. I think the reset button on the board would have worked, but I understand why you wouldn't want to open the device up. We shouldn't have to void our warranty to be able to do a hard reset.

Rhodizzle said:
Still nothing. Since its going to be over a month before I get a replacement, I'm just going to return it and wait for the new crop of tablets to come out. Thanks for the help guys.
Sent from my Dell Streak using XDA App
Click to expand...
Click to collapse
You might try nvflash.... worked on a friends.

GTO777 said:
You might try nvflash.... worked on a friends.
Click to expand...
Click to collapse
But was your friend's responding at all? I get absolutely nothing. the only thing the tablet does is give me a red light when it's charging and a green light when it's done. The power button does nothing and volume down + power does nothing. doesn't nvflash require a connection over USB before it can do anything?

wont turn on unless its plugged in

hey guys i just got my transformer today. a couple of times i shut it off and when i try to turn it back on it wont work unless i plug it in, even though the battery is above 90%

I have a very similar issue.
I have the B40 model, when I shut down, I can't turn back on. I have been leaving my TF on all day then just shut down at night and when I come to turn on in the morning, iit is fine. Today I had to restart due to wifi constantly saying it was turning off for no reason, upon shutting down, it wouldn't power back up. I hav left it for approx 1 and a half hours, still nothing. Doesn't make any difference if it is plugged in or not. My battery is full.
Really could do with some help with this issue, as it is really spoiling what I regard as a brilliant device.
Seg

Kreuger said:
hey guys i just got my transformer today. a couple of times i shut it off and when i try to turn it back on it wont work unless i plug it in, even though the battery is above 90%
Click to expand...
Click to collapse
Once you plug it in and it come on, does it stay on when you take the charger off?
Once on and you hit the power button does it do anything?
You might have a faulty power button IMO.

I don't know about Krueger, but mine doesn't do anything when you plug it in. I have to wait a few hours. When I last shutdown, I was trying to restart, it just never did. I had full charge. I can't even get into APX mode. My TF is stock unrooted. Power button works just fine when tablet is on, does exactly as it should.
Seg

Seg2012 said:
I don't know about Krueger, but mine doesn't do anything when you plug it in. I have to wait a few hours. When I last shutdown, I was trying to restart, it just never did. I had full charge. I can't even get into APX mode. My TF is stock unrooted. Power button works just fine when tablet is on, does exactly as it should.
Seg
Click to expand...
Click to collapse
I've seen reports of peoples getting this "deep sleep" and not able to turn it on easily. Not sure if there's a definite fix or not. Some peoples say they have good luck turning of the lock screen, some say they fixed it by factory resetting the tablet.

baseballfanz said:
I've seen reports of peoples getting this "deep sleep" and not able to turn it on easily. Not sure if there's a definite fix or not. Some peoples say they have good luck turning of the lock screen, some say they fixed it by factory resetting the tablet.
Click to expand...
Click to collapse
Cheers m8.
I will give this a try when I can turn it back on again. Its been approx 6 hrs now since I tried to restart it. I will have to wait till morning I think. When it has done it previously, I have left it on charge all night, even though there was more than half in it each time, and it seems to start up after about 7 - 10 seconds of holding the power button in.
Thanks again
Seg

So I have spent 15 mins listening to the back of the device while trying toturn on. From what I can hear it sounds like a quiet jet engine firing up for approx 1-1 and a quarter seconds then sounds like the jet engine turning off (I know this sounds wierd, but best way I can describe). Its almost like there isnt enough power to fire it all the way up. There also other noises going on even when I dont try and turn it on, so I don't think it is fully turned of. Maybe a deep sleep issue. I did notice on this occassion, befor I tried to restart that I had no internet connection and when I went to check wifi settings it said Wifi is turning off. I leave it set to default.
Thanks
Seg

[Q] Black screen after FW Upgrade, only vibrates.

Hello!
I just received my Infinity and started working on it, since there was a new Firmware available I downloaded and installed it.
When done it said "shutting down" and turned the Infinity off.
And this is were the trouble began .. since the last few hours I am trying to get it to work again but nothing seems to work.
Pressing the reset button with a paperclick won't work.
Volume down + Power only lets the Tablet vibrate after 10-12 seconds
Pressing power for 20 seconds (ASUS suggested this..) does the same thing.
with/without A/C Charger or docking station same thing, I get absolutely nothing on the screen.
When plugging it in via USB I get the APX mode.
Is there anything I can do at all? I don't want to send it back of course and thought APX Mode will maybe help me install and / fix something "blind" since I think the issue might be related to the Firmware upgrade..
Thanks in advance

Read this thread [How-To] All-In-One Guide For Asus Infinity (TF700) [24/09/2012] if you haven't already and you should be able to fix it.
Cheers Q

Quozl said:
Read this thread [How-To] All-In-One Guide For Asus Infinity (TF700) [24/09/2012] if you haven't already and you should be able to fix it.
Cheers Q
Click to expand...
Click to collapse
I did try the button combinations, and for NVFlash it says: THIS REQUIRES A NON-BRICKED AND UNLOCKED DEVICE. IT WON'T WORK ON ALREADY BRICKED DEVICES
Well.. I think mine already could be bricked, and I can't unlock it by installing the apk

If pressing Volume Down +Power only give you a black screen and not even the Asus logo it means you are bricked (could also be a hw failure, who knows) ... APX mode is useless for your device. So if u can't manage to boot into recovery or in fastboot mode i would recommend you to start the RMA process.

Pretoriano80 said:
If pressing Volume Down +Power only give you a black screen and not even the Asus logo it means you are bricked (could also be a hw failure, who knows) ... APX mode is useless for your device. So if u can't manage to boot into recovery or in fastboot mode i would recommend you to start the RMA process.
Click to expand...
Click to collapse
Nope nothing, doesn't matter if I press up/down + power for how long all I get is a 1 second vibrate after 10-12 seconds, with or without the Volume keys.
Pad is charged, same with A/C, when I try without the LED next to the power doesn't even turn on
Pressing the reset with a paperclip won't work either as stated so I guess it really is a brick...
How can a official Firmware Upgrade brick a device? I'm not new to Android and already own 3 HTC's all rooted and stuff but I never came across something like this ..

A few Things you can still try to recover the Infinty
Dude, that absolutely SUCKS! I would be so disappointed / angry if I were in your position, especially having the tablet for a short time. It DOES sound like a hardware failure (video seems out, but it's almost as if the tablet is running dark, and you just have no video. Can you return it to the retailer you bought it from? That would be 1000% better than an RMA, which is another thing that Asus does extremely poorly (They use a 3rd Part servive out of Grapevine Texas, and in MOST cases it is a nightmare. I don't understand why you can't bring/send it back to the point of purchase. You are not requesting arefund, just exchange for defective tblet.
As a last resort, do this: RUN THE BATTERY FULLY DOWN. Do not put the charge on, and keep checking if the tablet is powered on (touch the power button quickly, like you are taking it out of sleep mode. This could take the better part of a full day/night, but if you run it until the battery fully discharges, I remember a Prime user that this saved the day. It certainly is worth the effort, considering the alternatives.
Once it fully runs down, plug in the charger, and it should power up / begin charging and you will know in two seconds if it worked cause that Asus Logo will be the greatest site you will have seen in some time.
Oh, and something you can try before beginning that long process: I know you have already tried most reset methods, but humor me and put a pin in the reset hole - by HDMI, but instead of just pressing it briefly, press and hold for a FULL 30 + seconds. Some swear this changes the parameters, thiugh I am doubrtfull. More significant was mention that while holding the microswitch in, there is a "draining" happening of the memory onboard. I half belive it because years ago, I had an old HP Jornada Pocket PC, and one of the recovery procedures was remove the backup battery, and wait some inutes for a drain of memory to occur. You could SEE the LCD fading, like losing contrast super slowly. When it went completely blank was whenI was instructed to re-power up.
So try the reset pinhole for 30+ seconds
failing that, try a full battery drain
failing that try to return to point of sale
failing that do a shudder RMA with Asus. (Reach out to Gary Key - his PM and Email are listed in these forums. That way at least you will have a point of contact, and he may provide you with others. Good luck I feel for ya, especially with JB almost upon us! :cyclops:

Yosaku said:
Nope nothing, doesn't matter if I press up/down + power for how long all I get is a 1 second vibrate after 10-12 seconds, with or without the Volume keys.
Pad is charged, same with A/C, when I try without the LED next to the power doesn't even turn on
Pressing the reset with a paperclip won't work either as stated so I guess it really is a brick...
How can a official Firmware Upgrade brick a device? I'm not new to Android and already own 3 HTC's all rooted and stuff but I never came across something like this ..
Click to expand...
Click to collapse
Your are not the only one, afaik other users bricked their devices just by updaing with official firmware.However i'm a bit confused about that "shutting down" message and iirc the device only does a "restart" when updating,it doesn't shutdown.

Hi!
Thanks for the long reply
I tried holding the reset for more than 30 seconds, as I thought it did not help.
Any Tipps on how to drain the battery if I can't even turn it on? It vibrates after 10 seconds but I don't think that will drain much of the battery..
As for the RMA:
I won't do it via ASUS, they told me to but hell no.
Bought it from Amazon and already contacted them, I'll send it back when I get the confirmation they won't do an ASUS RMA, if they do want I just get my money back and buy a new one lol. Either way it is faster than Asus..
/edit
I wondered about the shutdown too and even waited quite some time after it went black because I thought it would boot back again, but well.. it did not
Thanks again!

Yosaku said:
Hi!
Thanks for the long reply
I tried holding the reset for more than 30 seconds, as I thought it did not help.
Any Tipps on how to drain the battery if I can't even turn it on? It vibrates after 10 seconds but I don't think that will drain much of the battery..
As for the RMA:
I won't do it via ASUS, they told me to but hell no.
Bought it from Amazon and already contacted them, I'll send it back when I get the confirmation they won't do an ASUS RMA, if they do want I just get my money back and buy a new one lol. Either way it is faster than Asus..
Thanks again!
Click to expand...
Click to collapse
Put it in APX mode and it will drain your battery.Btw are you sure the battery was charged enough when you updated?

Yosaku said:
Hi!
Thanks for the long reply
I tried holding the reset for more than 30 seconds, as I thought it did not help.
Any Tipps on how to drain the battery if I can't even turn it on? It vibrates after 10 seconds but I don't think that will drain much of the battery..
As for the RMA:
I won't do it via ASUS, they told me to but hell no.
Bought it from Amazon and already contacted them, I'll send it back when I get the confirmation they won't do an ASUS RMA, if they do want I just get my money back and buy a new one lol. Either way it is faster than Asus..
Thanks again!
Click to expand...
Click to collapse
I will try to find the thread - but check in the Prime threads - search for screen black, no video etc. The guy(s) that did it said that they just kept turning it on.. or touching the power switch - I know that's not too detailed. Here's the thing: a vibrate is what the tablet does NORMALLY when powering up... I think your may be running, you just can't see it. The only clues you can get are from the LED in the power button. Green means something like 95% charged. Amber means less that 14% and blinking amber (with no power supply attached means it is within the last few percent - Those are ballpark figures, you can find the full LED color descriptions with a bit of searching. Anyway it is you only indicator so, finding out waht the colors mean might help you in the discharging process.
Pretoriano80 said:
Put it in APX mode and it will drain your battery.Btw are you sure the battery was charged enough when you updated?
Click to expand...
Click to collapse
EDIT: JUST NOTICED you said this is from Amazon. If that's the case, you have no worries. Amazon replaces items faster/better than any other retailer. In fact Amazon will cross ship you a new one and you can return this after receiving the new one - at least that's how they did it with my TF101... two times. On the third exchange, they try to refund you and make you purchase it again, but I complained that it was not the SAME problem each time (this was on the docks) and they went ahead and sent me a 3rd one. Just go ahead and do that. You probably would be better off with a different one, but check it CAREFULLY for defects. I am convinced that these are near impossible for Asus to build without screwing up something - Screen separation (viewed from the edge), scratches, poor cutout/application of the Logo (My daughter actually bled from a cut it gave he -sharp edges) and the INFAMOUS Loose Screen, "Clicking" sound - squeeze the tablet gently all the way around. if it clicks or makes any grinding noises return it. For $500 any defect is unacceptable. Good luck!
Good idea. I also wondered about his state of charge while updating...

Pretoriano80 said:
Put it in APX mode and it will drain your battery.Btw are you sure the battery was charged enough when you updated?
Click to expand...
Click to collapse
Yes, it was even plugged in
SmartAs$Phone said:
I will try to find the thread - but check in the Prime threads - search for screen black, no video etc. The guy(s) that did it said that they just kept turning it on.. or touching the power switch - I know that's not too detailed. Here's the thing: a vibrate is what the tablet does NORMALLY when powering up... I think your may be running, you just can't see it. The only clues you can get are from the LED in the power button. Green means something like 95% charged. Amber means less that 14% and blinking amber (with no power supply attached means it is within the last few percent - Those are ballpark figures, you can find the full LED color descriptions with a bit of searching. Anyway it is you only indicator so, finding out waht the colors mean might help you in the discharging process.
Good idea. I also wondered about his state of charge while updating...
Click to expand...
Click to collapse
Thing is, even when it vibrates the LED is always off, only when I plug it in for charging it turns orange.
I will try the APX method Just plug it in to the PC and when the "can't find driver" message pops up it's in APX? Or do I have to install the drivers first?

Yosaku said:
Yes, it was even plugged in
Thing is, even when it vibrates the LED is always off, only when I plug it in for charging it turns orange.
I will try the APX method Just plug it in to the PC and when the "can't find driver" message pops up it's in APX? Or do I have to install the drivers first?
Click to expand...
Click to collapse
You don't need the PC at all, just put it in APX mode and let it be. The led turns on only when you plug the charger.
Edit: btw, you will know if it's in APX mode because even if the screen is off the device will get warm.

Pretoriano80 said:
You don't need the PC at all, just put it in APX mode and let it be. The led turns on only when you plug the charger.
Click to expand...
Click to collapse
Oh ok, since the only thing it does is vibrate I don't know if it is in APX Mode .. and it vibrates not after 5 seconds even when I press the volume up, but after ~10 seconds

Yosaku said:
Oh ok, since the only thing it does is vibrate I don't know if it is in APX Mode .. and it vibrates not after 5 seconds even when I press the volume up, but after ~10 seconds
Click to expand...
Click to collapse
Indeed it takes 10 seconds before it gets in APX mode.

Pretoriano80 said:
Indeed it takes 10 seconds before it gets in APX mode.
Click to expand...
Click to collapse
Ok .. I think it is in APX now ... I need to head out for a few hours anyway so wish me luck!
And thanks for your help so far

Maybe that is why they pushed the release back. Because they found it was bricking devices, lol. That sucks, tho, man. Good thing you bought it recently enough to send it back with Amazon. I wouldn't even bother with anything else and just sent it back.

Maybe....you could see what's going on if you connected it to the TV/Monitor on the HDMI port....

Soo I'm back!
It is still vibrating, so the battery is not empty yet ;(
I thought about the HDMI too but I don't have a mini-HDMI adapter.
Anyway it is Saturday and I might send it back today ... although I am usually not giving up till I fix something I guess their might be nothing else left.
Thanks so much for your support so far

SmartAs$Phone said:
if it clicks or makes any grinding noises return it. For $500 any defect is unacceptable. Good luck!
Click to expand...
Click to collapse
500$ ?? Wow ... I am actually thinking about getting one from the US! These things cost around 900$ with Dockingstation in Germany .. way to rip off people oO
Getting off Topic I know, just wanted to mention

Yosaku said:
Soo I'm back!
It is still vibrating, so the battery is not empty yet ;(
I thought about the HDMI too but I don't have a mini-HDMI adapter.
Anyway it is Saturday and I might send it back today ... although I am usually not giving up till I fix something I guess their might be nothing else left.
Thanks so much for your support so far
Click to expand...
Click to collapse
Ok another trick and it involves some luck. IF its on and you power it off you get a very,very short vibration (it's hard to feel it sometimes) and then you normally see a confirmation box appear in the middle of the screen asking you "Would you like to shut down?". Then you either tap Cancel or OK. Using your "minds eye" try to imagine where that box is on that black screen and tap it where you would to answer the question "OK". If you have any luck the damn thing will shut off and in ~8 seconds you'll feel a longer vibration indicating it turned off. Then DO NOT turn it on. Instead plug in the power adapter and let it power on and see if that puts your video back up.
I'm just wondering if the cable to the screen inside has popped off the main board. I know i've read about that happening but it usually occurs after a pretty good jolt to the unit.

[Q] HOX Won't Turn On with Sporadic Red LED

Yesterday, I was using the Navigation app on my phone. It was a busy day, so I think I had left the app running. In my previous experiences with the app, it stays on until I exit the app. Previously, I remember the phone running really hot.
Anyhow, yesterday sometime in the afternoon, I took my phone out and found the screen off. Pushing the power button didn't do anything. So I figure it probably had a drained battery and I plugged it in the wall to charge. About three or four hours later, I pushed the power button again - just to turn on my phone and see if I had any missed texts/calls. Nothing - the screen didn't turn on, but the red LED light was on. So I left it charging through the wall adapter, and went to go do some research about the problem.
Next morning the red LED was flashing. I tried the power button again, but nothing happened. Then I got a little panicky and tried the different button configurations I had read about: holding down the power button for x amount of seconds, holding down the power button and volume down button simultaneously - but again, nothing happened.
Fast forward to tonight - I'm not sure if my phone is charging or not, or if something else sinister is happening to it. I pushed the power button down about a half hour ago, and the red LED turned off. I then, plugged my phone into my computer, and I got a dialog pop-up that said "Device driver was not properly installed" with the driver name "qhsusb_dload".
Any idea what this issue is? Or could you point me to further info somewhere?
Any help is much appreciated!
PS. I got my HTC One X just about 2 and a half months ago at the end of November. My phone isn't rooted, and the most "advanced" thing I did with it was put ADWLauncher on it.

intellectualese said:
Yesterday, I was using the Navigation app on my phone. It was a busy day, so I think I had left the app running. In my previous experiences with the app, it stays on until I exit the app. Previously, I remember the phone running really hot.
Anyhow, yesterday sometime in the afternoon, I took my phone out and found the screen off. Pushing the power button didn't do anything. So I figure it probably had a drained battery and I plugged it in the wall to charge. About three or four hours later, I pushed the power button again - just to turn on my phone and see if I had any missed texts/calls. Nothing - the screen didn't turn on, but the red LED light was on. So I left it charging through the wall adapter, and went to go do some research about the problem.
Next morning the red LED was flashing. I tried the power button again, but nothing happened. Then I got a little panicky and tried the different button configurations I had read about: holding down the power button for x amount of seconds, holding down the power button and volume down button simultaneously - but again, nothing happened.
Fast forward to tonight - I'm not sure if my phone is charging or not, or if something else sinister is happening to it. I pushed the power button down about a half hour ago, and the red LED turned off. I then, plugged my phone into my computer, and I got a dialog pop-up that said "Device driver was not properly installed" with the driver name "qhsusb_dload".
Any idea what this issue is? Or could you point me to further info somewhere?
Any help is much appreciated!
PS. I got my HTC One X just about 2 and a half months ago at the end of November. My phone isn't rooted, and the most "advanced" thing I did with it was put ADWLauncher on it.
Click to expand...
Click to collapse
qhsusb_dload usually indicates a hard brick. take it for warranty repair. given what you've described most likely you've had a hardware failure of some sort.

Sounds like you've ended up in qualcom download mode somehow. When you held down power and volume down, was you're phone plugged in? I think I accidentally made it to qdl mode once when my phone was plugged into the wall. Try unplugging power, and press and holding power and volume down, see what happens.. Otherwise you may be able to get help from 18th.abn who seems to know quite a bit about the qualcom download mode. Good luck.
Sent from my One X using xda app-developers app

It pains me to read your post because I had the same exact thing months ago. The phone turned off while using navigation and never turned on again. At the time JET didn't exist so there was nothing I could do about it.
Look here and see if it might help your situation and maybe avoid a warranty repair
http://forum.xda-developers.com/showthread.php?t=1982442
I've seen this type of post a few times and makes me think that there's definitely something wrong with the evita that's bricking these phones all on their own. Maybe hardware like someone else suggested so maybe warranty repair might be safer.
Best of luck. :thumbup:

Thank you all for your help and suggestions. It appears my phone is dead, completely. I had high hopes, but now I think I'm wasting energy. I called HTC and they said they'd send me an email with ticket info to return it so they could fix it. But they never sent the email. Now I must chase after them and try to get them to fix my phone. Sigh. I would try JET, but I don't run Linux and don't think I'm as tech savvy as I should be to set it up.
Thanks again!

intellectualese said:
Sigh. I would try JET, but I don't run Linux and don't think I'm as tech savvy as I should be to set it up.
Click to expand...
Click to collapse
IMO, if you are bone stock (sounds like you are) its not worth it to mess with JET. Just send the phone to HTC (or your carrier, if they handle warranty matters - they are often easier to deal with than HTC). It may well be a hardware issue, that JET won't fix.

redpoint73 said:
IMO, if you are bone stock (sounds like you are) its not worth it to mess with JET. Just send the phone to HTC (or your carrier, if they handle warranty matters - they are often easier to deal with than HTC). It may well be a hardware issue, that JET won't fix.
Click to expand...
Click to collapse
Yea... if you are in qdl download.. sounds like a hardware failure..sending it back to HTC might be the only way to go..

Up and running again, but w/ new phone
Yup, I took it to my carrier (ATT) yesterday and they couldn't do anything with it, so they gave me new phone right there and then, which was great news. Bad news is I have to start from scratch. But at least I've learned to back up early and often.

Not sure if you could have done anything about this as it seems to be a hardware failure

Phone won't boot

Hey guys,
My phone shut off unexpectedly today and now won't turn back on. When I try to power it on I see the Google logo for a couple seconds and then it'll just shut off again. I tried holding the volume up/down buttons to access the bootloader, but right after I get to the screen it just restarts itself again.
Connecting to power (AC or USB) causes it to constantly reboot over and over, it just shows the Google logo for a couple seconds and then restarts again.
Any ideas on what I can do?

rosscarrothers said:
Hey guys,
My phone shut off unexpectedly today and now won't turn back on. When I try to power it on I see the Google logo for a couple seconds and then it'll just shut off again. I tried holding the volume up/down buttons to access the bootloader, but right after I get to the screen it just restarts itself again.
Connecting to power (AC or USB) causes it to constantly reboot over and over, it just shows the Google logo for a couple seconds and then restarts again.
Any ideas on what I can do?
Click to expand...
Click to collapse
Provide more information for a starter - stock? unlocked bootloader? rooted? third party recovery? rom and if yes which?
If it's stock I'd RMA it.
If not what did you do immediately before the problem started?
try holding the power button for > 2 seconds which should turn it off completely, leave it on a wall charger for at least a couple of hours then turn it back on - I doubt it'll fix the problem but it's a simple thing to try...

Clancy_s said:
Provide more information for a starter - stock? unlocked bootloader? rooted? third party recovery? rom and if yes which?
If it's stock I'd RMA it.
If not what did you do immediately before the problem started?
try holding the power button for > 2 seconds which should turn it off completely, leave it on a wall charger for at least a couple of hours then turn it back on - I doubt it'll fix the problem but it's a simple thing to try...
Click to expand...
Click to collapse
Everything on it is stock, no ROM, not rooted. I had just taken it out of my pocket to check the time, put it back in my pocket and then felt it vibrate, took it back out to see it at the Google logo and haven't been able to get it started since. There was one or two times when it got past the Google logo and started to show the start up animation (the four colours bouncing around or whatever it is) but then it shut off again.
I tried holding the power button to completely turn it off, but plugging it into the wall charger just causes it to repeatedly attempt to boot like I mentioned earlier. I'll leave it for a while and hope for the best

Sounds like the mobo is bad. Most likely will have to rma it.

rosscarrothers said:
Hey guys,
My phone shut off unexpectedly today and now won't turn back on. When I try to power it on I see the Google logo for a couple seconds and then it'll just shut off again. I tried holding the volume up/down buttons to access the bootloader, but right after I get to the screen it just restarts itself again.
Connecting to power (AC or USB) causes it to constantly reboot over and over, it just shows the Google logo for a couple seconds and then restarts again.
Any ideas on what I can do?
Click to expand...
Click to collapse
Do you have a case on? The case could be faulty.
Sent from my Nexus 5 using Tapatalk

jd1639 said:
Sounds like the mobo is bad. Most likely will have to rma it.
Click to expand...
Click to collapse
Maybe not. Sounds like a stuck power button to me.
OP does the phone just endlessly repeat this cycle? If so it's rebooting itself do to a stuck power button. One other users already reported similar issues and his power button was indeed stuck. Mash the power button hard for a minute to see if you can unstick it.

theesotericone said:
Maybe not. Sounds like a stuck power button to me.
OP does the phone just endlessly repeat this cycle? If so it's rebooting itself do to a stuck power button. One other users already reported similar issues and his power button was indeed stuck. Mash the power button hard for a minute to see if you can unstick it.
Click to expand...
Click to collapse
You got it!
Thanks so much, really wasn't looking forward to waiting for weeks while the RMA went through. The button didn't appear to be stuck - it was still clicky - but after mashing it for a minute it started up normally and appears to be fine now.

Did you flash any ROMs or anything previously?
Sent from my Nexus 5 using xda app-developers app

scottdouglasdick said:
Did you flash any ROMs or anything previously?
Sent from my Nexus 5 using xda app-developers app
Click to expand...
Click to collapse
brother the issue is gone, as mentioned "sticky power button" was causing it. read the thread before posting. btw thanks for effort anyway... haha
:laugh::silly:

Hi all. Sorry to reopen an old thread (but xda suggested I check here before making my own thread).
I think we have the exact same problem with a Nexus 5. Unfortunately, bashing the power button doesn't seem to be helping (and makes me feel slightly silly .
Anyone know how much effort it would be to take it apart to get to the part that's stuck? Any good instructions?
Thanks.

Weird, I have the same issue starting a few hours ago. I updated to the Oct 17 beta of Cataclysm then a hour later it happened. But was told it sounds like the power button issue.
Took it apart, tried to fix it. If plugged in I can get into the bootloader, but then it reboots again. I've tried tapping it on a hard surface, and it gets seems like it almost fixes it because it'll connect to my laptop but then reboots again.
Could it be the battery? It was fully charged but then died as I was deleting hundreds of photo's in Dropbox to move photo's over from my phone because it was full.

I too am running into this same issue. My screen cracked so I replaced the digitizer with some success. In the process I damaged the battery and needed to replace it. When I got the new battery and replaced it my phone is now unusable.
When unplugged: I turn on the phone and it's running the ANDROID animation then turns off.
When plugged in: I turn on the phone, the ANDROID animation runs then the phone restarts and continues the process over and over again.
I then flashed the phone with Marshmallow and the same thing happens. Except now that I flashed it I get the Android icon with the spinning gear. So; I flashed it back to 5.1.1, but the same result.
Could I have physically damaged something inside or is it a battery issue? Thanks for any insight.