Database Info

How to root Lenovo S686

I have Lenovo Lephone S686 with following specifications. If anyone has any idea on how to root this phone, please reply.
CPU: Qualcomm Snapdragon MSM8225 Dual core 1.2GHz
GPU: Qualcomm Adreno203
Memory : RAM : 512MB / ROM : 4GB eMMC

Found already?
Am sick and tired of the stock....
tried 1-click root, king root, and all other root method and failed...

Anybody knows how to root this? bin4ry method did not work.

Hi everyone,
I found these instructions for rooting the Lenovo S686 from Chinese forums, you can try and see if it works. Below are the instructions which I translate from Chinese.
You need to install a 3rd party recovery, because S686’s original recovery cannot install unsigned update.zip. There are 2 kinds of update.zip, smaller one, about 1-2MB, is for obtaining root. The bigger one is for flashing the entire system. There is no 3rd party recovery for S686, but after looking at some other models’ recovery, I think we can use A765E recovery.
Turn on USB debugging. Connect USB wire. For desktop PCs, it is better to use the back USB port.
Download this: ht tp://pan [dot] baidu [dot] com/share [slash] link?shareid=415868&uk=4130114971
After uncompressing, you will get 2 files, update.zip and Lenovo_A765E_OneKeyTools.exe. Do not uncompress the update.zip. Just put it on the TF card.
Make sure the drivers are installed. Most of the time, if it doesn’t work, it is because of driver problems. You can check whether drivers are properly installed by going to Device Manager.
Installing fastboot driver: without disconnecting USB wire, turn off phone, take out the battery. While pressing ON and VOL -, connect USB wire. Most likely fastboot driver will install automatically.
Run 刷入中文Recovery (Chinese CWM recovery). Phone will reboot 3 times.
Entering recovery mode: Turn on the phone. Red LED will light up, before it goes off, press VOL + and -, hold until Lenovo logo appears. If you see Android recovery, it means the above steps did not work. If you see Chinese CWM recovery, flash in the update.zip that you put onto the TF card.
After this post on the Chinese forums, there were many people saying it works, and many people saying it does not work. I (tangys) could not get it to work with my S686. So either I am an idiot, or the guy who wrote the original post is an idiot. So please try it and post back here whether it works for you or not. Thanks.

sralli said:
i was also facing the same problem. i couldn't root my phone, at last i found solution on this page-
Mod Edit: link removed, it worked for me i hope it works for you, and it roots in just 5 minutes
Click to expand...
Click to collapse
just use framaroot i think it's downloadable on google play then use the gandalf exploit!

Just FYI I`ve noticed that you`ve mentioned Chinese characters in the previous text, let me know if you`ve met any translation problems, i`m the one can do the help

hi.from where i can find kernel or some ROM for lenovo s686.thanks

This following method worked for me. Got ride of the bloatware that Lenovo put on there.
got the files from
www lenovohome net/thread-137736-1-1.html
some detailed instructions to setup here
lenovo zol com cn/177/1763_1767961.html
I'm a noob at rooting/changing firmware so took some extra time.
Need to setup the ADB drivers. This was slightly involved as the drivers from the phone ITSELF showed up as not properly signed. So I had to go and turn off the win8.1 check to get it properly installed. You end up with Lenovo ADB Device in device mgr and a few other Lenovo items.
Basically, there's an exe that you run (name has chinese char in it.. so it may look strange). It's an automated CWM installer. My version now shows CWM 6.0.1.5. All the text in there is in chinese.
Lastly, you flash in the update_v2.zip and when done, you get a root enabled , bloatware removed CYANOGENMOD system.
One note: when done flashing and you choose reboot, there is actually a prompt for you to "repair root". I've found that you must say yes at this point. Otherwise, root is not working when rebooted. You'll have to repair root later.
That's the good side. Now the bad side:
This phone only has 3 keys (pwr, vol+ / -) so there's currently no way to get menu button.
There is also no store in the version flashed....no sure how to install any apps
Need to resolve these issues.

Looking for original factory rom (P5100)

Hello everyone, I have big problem and I dont know how to solve it. Samsung galaxy tab 2 5100 was stucked in boot loop and with odin I put philz recovery on tablet and with options inside backup all files to sd card. And after that deleted everything on tablet. Now I dont have any rom installed on tablet and when I turn it on it just on black screen with samsung tab 2 logo. I found couple of download links for original factory rom for europe but they are all on hotfile website and that website is shuted down by US court. So now I dont know what to do and I cant download factory rom.
Can someone help me what to do now???

AVVL said:
Hello everyone, I have big problem and I dont know how to solve it. Samsung galaxy tab 2 5100 was stucked in boot loop and with odin I put philz recovery on tablet and with options inside backup all files to sd card. And after that deleted everything on tablet. Now I dont have any rom installed on tablet and when I turn it on it just on black screen with samsung tab 2 logo. I found couple of download links for original factory rom for europe but they are all on hotfile website and that website is shuted down by US court. So now I dont know what to do and I cant download factory rom.
Can someone help me what to do now???
Click to expand...
Click to collapse
Put GT-P5100 in the search box and choose the Rom that you want from the list. You'll need to register to get the link.
http://www.sammobile.com/firmwares/
Sent from my GT-I9505 using Tapatalk

Thx man for fast reply. But now when i think about this if i install this original factory rom, can I and how recover my data and pictures that i backup with philz recovery on my sd card??? And can i do that with original rom??? (i am doing this stuff for the first time so i am noob so this is all new for me). Thx

AVVL said:
Thx man for fast reply. But now when i think about this if i install this original factory rom, can I and how recover my data and pictures that i backup with philz recovery on my sd card??? And can i do that with original rom??? (i am doing this stuff for the first time so i am noob so this is all new for me). Thx
Click to expand...
Click to collapse
You mean a nanodroid backup?
Yes that's possible

AVVL said:
Thx man for fast reply. But now when i think about this if i install this original factory rom, can I and how recover my data and pictures that i backup with philz recovery on my sd card??? And can i do that with original rom??? (i am doing this stuff for the first time so i am noob so this is all new for me). Thx
Click to expand...
Click to collapse
You need to quote me in your reply or I don't get a notification.
There's nothing to stop you rooting it again and extracting the data from your nandroid backup once you've installed the Rom
Sent from my GT-I9505 using Tapatalk

You can't really restore them, because they're on a different ROM, it'd overwrite all your fresh and fast ROM.
In two words: you can't.
You will need a country specific firmware, where did you buy your P5100; was it from.. anywhere in the world? Check for a sim card slot.
If it doesn't, get on to reading!
1. Find how much bits your windows is.... this can be done by opening the start orb in the bottom left corner, then right-click on computer. Click Properties, and look for 64 or 32.
Pick 64 if you have 64, or pick 32 if you have 32.
2. Install drivers according to your bits.
These will ensure good experience.
- 64bit: http://drivers.softpedia.com/get/MOB...dows-x64.shtml
- 32bit: http://drivers.softpedia.com/get/MOB...dows-x86.shtml
3. Download UK recovery! That is, if you don't have a SIM card slot.
Find here: http://www.sammobile.com/firmwares/3/?download=22456
Now, I was quite lazy to write a tutorial, so I did copy some sources. they will all be given credit.
1. Download and Install the Samsung USB drivers to your PC from the link above. Reboot your system once after installation. If you have already have KIES installed you can skip this step
Extract the Odin Package you downloaded earlier to your desktop. Look for the Odin exe file. That's the only one we would be using
Extract the downloaded stock firmware zip file to your desktop
On your Tab, go to Settings > Developer Options and Enable USB Debugging
Now Power off your Tab completely. We will now be putting your device into Download mode or Odin Mode as it is also called. Download mode is basically a Samsung Exclusive mode which allows flashing of firmware via Odin. Odin can only communicate with Samsung devices when they are in Download Mode. To get there, press and hold these keys together: Volume Down + Power. Then press Volume Up to enter download mode
On your PC, launch Odin by double clicking the exe file in the Odin folder. Just make sure that Samsung KIES is not running on your PC at this time. KIES and Odin don't like each other very much.
Connect your Tab 2 to PC using the OEM USB cable. Any microUSB cable should work, but I prefer to use the one supplied with the phone to avoid any unforeseen complications. You should see the message Added!! in the main Odin message box like in the screenshot below, as well as as COM Port number in the first slot directly above the message box, which tells you that Odin has recognized your device
odin_zpsc9caf496.jpg
In Odin, click the PDA button, locate the stock firmware .tar file that you extracted in Step 3. If there are additional file for the modem and CSC, add those as well. Make sure the Auto Reboot and the Reset Time boxes are checked and Re-partition box is NOT checked.
Double check everything in Step 8, then hit the Start button to restore your Tab 2 to stock Samsung firmware
Once Odin has finished flashing the CWM recovery, your Tab should automatically reboot. And if the flashing was successful, you should see the word PASS! against a green background at the top-left in the Odin window. This means it is now safe to disconnect your device. (SOURCE: http://androidevolved.com/forums/ga...tore-stock-firmware-gt-p5100-p5110-p5113.html)

Help me unbrick my lenovo A850!

Hey guys! My phone is now a brick. Can anyone show me how to repair the boot for it? Many thanks.

hungtrauvang said:
Hey guys! My phone is now a brick. Can anyone show me how to repair the boot for it? Many thanks.
Click to expand...
Click to collapse
Flash a new rom
Watch this video...

hungtrauvang said:
Hey guys! My phone is now a brick. Can anyone show me how to repair the boot for it? Many thanks.
Click to expand...
Click to collapse
What happens if you power it on while holding down the up and down buttons?

Frogmanstar said:
What happens if you power it on while holding down the up and down buttons?
Click to expand...
Click to collapse
Nothing happens. Really sad.

hungtrauvang said:
Nothing happens. Really sad.
Click to expand...
Click to collapse
This just means you don't have a recovery.. just flash a new rom.

hi XDA community i have a problem regarding my a850 and i hope u or anybody can reply this comment in an instance cuz im in emergency...
IM EXPLAINING MY PROBLEM VERY DETAILED SO IT'S GONNA BE VERY LONG COMPOSITION, INCLUDING FROM IM ROOTING THE PHONE UNTIL I TYPED THIS COMPOSITION
so recently i "Framarooted" my device and was working properly as i expected,then i want to install TWRP, i see my baseband version does not have ROW or CN in there, it kinda like "A850.V13 ...(cant remember)", but i flashed anyway using the ROW version of TWRP and Mobileuncle MTK Tools. When I want to enter recovery (via MTK Tools) it doesnt show up, just stuck at white,big "Lenovo" logo (it probably doesnt work) but i was able to boot back to normal. Then i used System App Remover from Play and attempted to delete some chinese apps, and I DID a mistake... i was so clumsy enough to delete all chinese apps that origins from the rom i accidently deleted the file "classical" (which i guess the entire system ui, launcher etc) . Upon after deletion of that file I SHOULD HAVE NOT DELETE , it suddenly booted off with the startup sound muted halfway (its like, the boot startup sound have like 4 second duration and i heard the sound just for 1 sec).
Then it boots up again, but stuck at the logo "Lenovo For Those Who Do" after startup animation, so i assume this is bootloop or soft brick
Realising this incident i GOOGLED " a850 bootloop","a850 unbrick","a850 stock rom","a850 emergency reset" and "a850 emergency backup", then I found a website which describes how to flash stock rom to a850, so i did that, as it might work, but actually not for my case. I followed and downloaded exactly steps and files from that website and loaded Flashtool with its scatter file, then ticked PRELOAD and selected the preload.img, followed by checking USB mode ,clicking "Forced High Speed", checked the DA DL thingy, clicked Firmware Upgrade and the progress bar moved, after that i plugged my phone, without battery, to the pc via usb. I heard the hardware insert sound, but, Flashtool did not start flashing, it;'s still SEARCHING.
Then I read that u need the USB drivers, so I assume i do not have drivers for this phone. I used the Device Manager step and when I plug my phone, it pops up "MT65xx Preloader"(or MTK i dont remember) then I quickly rightclick and "Update Driver". It has two selections, ONLINE or BROWSE, so i clicked the online solution, but Windows seems cant find the driver i need,
so i used BROWSE option, which i used your usb driver by entering the directory of the driver in your file in "C:\Users\User\Downloads\Compressed\Lenovo_Drivers_SP_Flash_Tool_v3.1316.0.150\Drivers" clicked install then it pops up an error "The third party INF does not contain digital signature information", so it doesnt install. So I used USBDeview and plugged my phone again without battery, it pops up "MT65xx Preloaded" with a purple dot, and if you need, i rightclicked that purple dot and clicked PROPERTIES, and here's information it gave:
Device Name: MT65xx Preloader
Device Type: CDC Data
Description: MT65xx Preloader
Connected: Yes
Safe to Unplug: NO
Disabled: NO
USB Hub: NO
Drive Letter:*blank
Serial Number:*blank
Created Date: 12/10/2014 2:01:15 AM
Last Plug/Unplug Date:12/10/2014 2:01:15 AM
VendorID: 0e8d
ProductID :2000
Firmware Revision : 1.00
USBClass: 0a
USBSubClass:00
USBProtocol: 00
"Hub Port" until "DeviceMfg" is blank
Power: 500mA
USB Version: 2.00
Driver Description: *blank
Driver Version:*blank
Instance ID: USB\VID_0E8D&PID_2000\5&9ec43f0&0&9
After checked, i resorted to HARD RESET via recovery (i tried to go to recovery again to see there's hope in there) and it BOOTED TO RECOVERY! (yay) but again problem strikes, the recovery I see now is FULLY CHINESE i dont understand even a single option i gave there.
So now my phone condition is still cant boot to launcher, and my very last resort is to use the JTAG option
pls help me u all and pls reply ASAP
thank you

irfanadli97 said:
...clicked install then it pops up an error "The third party INF does not contain digital signature information", so it doesnt install.
Click to expand...
Click to collapse
You should log in to windows with out drivers verification in order to install the drivers. Tutorial on how to do than on windows 8 here. Then flashtool should regognize the phone... (you should fix this problem because you may also need it in the future)
There is also a way to fix your phone (if the classic theme is the problem) using ADB. Go to this page and scroll down to ADB method(tutorial) in order to install the classic.apk as a system apk through ADB.
(i am attaching you the apk: View attachment Theme_classic.apk)

Very thanks though cuz this actually solves my problem on my previous devices which doesn't detect upon connection, but I've actually resorted
to do unsoftbrick by a more professional person in my town (he sells and services phones) and it charged me RM50 ($15). Now my phone is back to normal with a rooted state (Chinese superuser app)
Again thanks for replying.
PS:also can somebody redirect me to lenovo a850 modding page? anybody

irfanadli97 said:
Very thanks though cuz this actually solves my problem on my previous devices which doesn't detect upon connection, but I've actually resorted
to do unsoftbrick by a more professional person in my town (he sells and services phones) and it charged me RM50 ($15). Now my phone is back to normal with a rooted state (Chinese superuser app)
Again thanks for replying.
PS:also can somebody redirect me to lenovo a850 modding page? anybody
Click to expand...
Click to collapse
You did good going to a shop...
What do you mean by "Lenovo a850 modding page"?

u know, where rooted users mod their phone with frameworks, custom roms, installing awesome stuff in theirs'
Sent from my Lenovo A850 using XDA Free mobile app

irfanadli97 said:
u know, where rooted users mod their phone with frameworks, custom roms, installing awesome stuff in theirs'
Sent from my Lenovo A850 using XDA Free mobile app
Click to expand...
Click to collapse
This is such a forum

Tried Installing a custom rom using Flashtool. Now the phone can't come and can't be dected by my pc. Installed the Drivers and they Installed. At first first I was having a Brom Error report Now nothing happens when I p,lug the phone.

[GUIDE] SM-T210 PhilZ Touch Recovery + Root

Hey guys, today I'm back with another root guide. Of course it also shows you how to install recovery in case you don't have it. I will try to make the guide as easy to understand as possible, you know, for noobs. It's going to be a long day.
First thing, you can get any SuperSU zip that you want from Chainfire. I have the guaranteed one that I used to root mine. It depends on you. I will give you both links to Chainfire's thread and my file.
Requirements
-A PC
-Your device with USB cable(its battery level would better NOT below 30%)
-A stable internet connection
-Your brain(it can blow up, man, seriously)
A warning before we start:
-Files you download on your PC:
+Drivers
+Odin+Recovery
-Files you download to your device: Root(Chainfire's or mine)
Download all of them before you do anything. Extract Odin and recovery
The drivers are for Windows. I don't know if there are Samsung USB drivers for Mac or not.
Main Guide
1. Enable USB debugging on your device in developer options(to enable dev options, go to about phone, rapidly tap build number until it says that you have enabled it)
2. Open the drivers setup and install it on your PC.
3. Boot to Download mode on your device(Power off your device, then hold power and volume down button. When there's a triangle, press volume up.)
4.Connect your device to your PC via USB cable.
5.Run Odin on your PC
6.Uncheck Auto Reboot, click PDA and choose the recovery file.
7.Hit Start and wait until there's a PASS sign. Plug out your device and hold power button afterwards.
8.Hold power and volume up button to boot into recovery mode.
9.Tap Install, go to the folder where you put the root file in, then tap the root file.
10.Swipe to falsh.
11.Reboot, download Root Checker to verify
ENJOY!
Special thanks
Daffen Kurm (for supporting me all the time)
Liam Francis, Laguire Sien Tiamat and Kamross Sorberg (for helping me all the time)
Kohlner Freisch (idea to make this post after a while)
Squadron 3(Anti-Hacking)

Download Links
Odin+Recovery: https://www.androidfilehost.com/?fid=24269982087002864
Drivers: https://www.androidfilehost.com/?fid=24269982087004084
Root(mine): https://www.androidfilehost.com/?fid=24269982087002856
Chainfire's thread: http://forum.xda-developers.com/apps/supersu/2014-09-02-supersu-v2-05-t2868133

Does this work on SM-T210 7.0" ??
Thanks
Sent from my SM-T210 using XDA-Developers mobile app

b4zz41 said:
Does this work on SM-T210 7.0" ??
Thanks
Sent from my SM-T210 using XDA-Developers mobile app
Click to expand...
Click to collapse
Well, I tested it on the 8 or 9 inch whatever and it worked out. But there's a still chance that this won't work on models other than its own. You can check and send me your device's model and i'll figure out another way for you. But don't try this method, it will only make it worse.
Sent from my SM-N900 using XDA-Developers mobile app

Root
Hey, my device is not starting. It hangs when logo appears. Device was rooted. Can i still install Custom ROM or tell me another solution to make my device work again. Already tried Factory reset but doesn't works.

Nick Silicon said:
Hey, my device is not starting. It hangs when logo appears. Device was rooted. Can i still install Custom ROM or tell me another solution to make my device work again. Already tried Factory reset but doesn't works.
Click to expand...
Click to collapse
Ok, you should try the other root zip file, because I posted 2 to make sure that you can do it all over again. Or you should first try rebooting your device again. I'm sorry for the inconvenience

[ROOT] Samsung Galaxy Tab E - T561

Hey guys,
After long search for root for my Tab E - T561, i was able to root my tab with kingoroot pc application. so long story short, i am uploading tar file which will root T561 on kitkat 4.4.4.
How to:
1. Download the attachment
2. Extract it using 7zip or winrar.
3. Download latest Odin 3.10.7 (Google it)
4. Reboot your Tab to Download mode by holding home button, volume down button and power button at the same time.
5. Click AP and choose extracted tar file and Press start.
6. Voila! Rooted Tab E - T561
7. Press Thanks
need any help, PM me

hey tried this but flash failed. now i am stuck at boot logo
imfaraz said:
Hey guys,
After long search for root for my Tab E - T561, i was able to root my tab with kingoroot pc application. so long story short, i am uploading tar file which will root T561 on kitkat 4.4.4.
How to:
1. Download the attachment
2. Extract it using 7zip or winrar.
3. Download latest Odin 3.10.7 (Google it)
4. Reboot your Tab to Download mode by holding home button, volume down button and power button at the same time.
5. Click AP and choose extracted tar file and Press start.
6. Voila! Rooted Tab E - T561
7. Press Thanks
need any help, PM me
Click to expand...
Click to collapse

Any update?
Sent from my SM-T560NU using XDA Free mobile app

sammymcalaxy said:
Any update?
Sent from my SM-T560NU using XDA Free mobile app
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=3300291

Sorry for being so late!
lijoc said:
hey tried this but flash failed. now i am stuck at boot logo
Click to expand...
Click to collapse
What Model do you have there buddy?

- Install Kies3 from samsung.
- It will not recognize the device .... no panic!!!
- Open in menu Tools->Update and initialize firmware
* put the model number and serial number you have in the back of the tablet...
- It will download the proper original firmware from the samsung site and once done push on restore

sm-t561
Not work. F A I L !

bejinaru said:
Not work. F A I L !
Click to expand...
Click to collapse
Do it the proper way!
http://forum.xda-developers.com/showthread.php?t=3302935

How do I do it with out PC

I have the T561M Tablet.
Is there a ROM for android 6 or 7 for the T561M ??? At where???
Because I have ROOT and RECOVERY, but ROM is missing.
sammymcalaxy said:
Any update?
Sent from my SM-T560NU using XDA Free mobile app
Click to expand...
Click to collapse

lijoc said:
hey tried this but flash failed. now i am stuck at boot logo
Click to expand...
Click to collapse
hi. im suffering the same problem after rooting. stuck at boot logo. have you found a way to fix it?

no root t561m
My T561m is with the December 2016 security update and I was not able to do root. Has anything changed? Any suggestion?

ciqvillanueva said:
hi. im suffering the same problem after rooting. stuck at boot logo. have you found a way to fix it?
Click to expand...
Click to collapse
*this way worked for my soft bricked SM-t561 Galaxy tab E. and I hope it'll work for you'll too. after this process all the data from your device will be gone as if it was bought new. Pls make sure you charged your device so that it won't shutdown during the process.
Make sure you have installed samsung USB drives latest version before doing this. If not download it from this link. -----> https://droiddocket.com/download/samsung-usb-drivers-v1-7-23-0/
1.type your model number and search google for flashable firmware for your device. Download it, and unzip it.
2.Download Odin latest version, unzip it and double click Odin3_v3.14.4 file .
3.then you'll get a notification probably, click ok. After that you'll get like this, after that take your soft bricked phone and click power button + volume up /down + home button then
your phone will look like this,
after that connect your device to the computer, on your computer you'll see this.
then click "AP" and select the unzipped firmware you downloaded and click enter.
after that click start and it will start flashing you'll see the progress from your device and from your pc. It will take a while so DON'T un plug the device. after it's done you'll see this in your pc then unplug your device and then it's done.
Don't mind my gramatical mistakes. I hope this helped you.

Lunaworks2007427 said:
*this way worked for my soft bricked SM-t561 Galaxy tab E. and I hope it'll work for you'll too. after this process all the data from your device will be gone as if it was bought new. Pls make sure you charged your device so that it won't shutdown during the process.
Make sure you have installed samsung USB drives latest version before doing this. If not download it from this link. -----> https://droiddocket.com/download/samsung-usb-drivers-v1-7-23-0/
1.type your model number and search google for flashable firmware for your device. Download it, and unzip it.
2.Download Odin latest version, unzip it and double click Odin3_v3.14.4 file .
View attachment 5244307
3.then you'll get a notification probably, click ok. After that you'll get like this, after that take your soft bricked phone and click power button + volume up /down + home button then
your phone will look like this,View attachment 5244319
after that connect your device to the computer, on your computer you'll see this.
View attachment 5244321
then click "AP" and select the unzipped firmware you downloaded and click enter.
View attachment 5244311
after that click start and it will start flashing you'll see the progress from your device and from your pc. It will take a while so DON'T un plug the device. after it's done you'll see this in your pc then unplug your device and then it's done.View attachment 5244329
Don't mind my gramatical mistakes. I hope this helped you.
Click to expand...
Click to collapse
Unfortunately it did not work with rooting, did it as described above.
After the reboot, the tablet hangs at the start screen and does not boot any further.
how can I undo this, because before the device ran without problems

Hello everyone. I need help here.
I have a Samsung SM-T561 & some months ago, I upgraded to version 7.1
Then a few days ago, I wanted to upgrade it to version 10.
That's where things got messed up!
1st. I didn't make a backup of what current ROM.
2nd. I completely forgot to enable USB debugging (again, despite It wasn't the first time I used custom ROM)
3rd. The problem must have been from the ROMS I installed. They didn't work. So I factory resetted EVERYTHING. EVERYTHING. INCLUDING THE SYSTEM.
So basically, I HAD TWRP. I HAD NO OS. I DIDNT TURN ON USB DEBUGGING MODE.
Then I understood that I didn't need ODIN anymore because I had TWRP.
So.
I downloaded the files to flash again. On SD card. And inputted it inside . So it still DIDNT WORK!!
Then I flashed in IMAGE form.
Then my TWRP DISAPPEARED.
IM ON CONSTANT BOOTLOOP.
THE ONLY THING I CAN ACCESS IS THE DOWNLOAD MODE.
AND I CAN NOT CONNECT WITH ODIN BECAUSE I HAVENT TURNED ON USB debugging...
Someone should kindly... please. Get back to me