Related
After the squeaking back cover of the Touch Dual, another noisy HTC unit ! At least my test unit it seems...has anyone else noticed that when you tap at the top of the screen, say the x box, when you let it go there is a noise of something coming unstuck/unglued ?
If you swipe your thumb from let to right applying some gentle pressure it is event more obvious. Anyone else or is my screen maybe not properly glued on...
I listened really closely, and the only sound I could detect was my oily finger coming off the screen! You may have a defective unit because I don't seem to detect the problem you are talking about. Hope this helps!
Yes, thanks, will need to take it back then, just my luck !
You did apply some moderate pressure didn't you ? It's particularly noticeable around the loudspeaker and camera openings. Or it maybe static I'm hearing, doubt it since I don't have the noise at the bottom of the screen.
GpsPasSion
i tried several times but there's no noise.
Maybe u should check it with HTC or the store where u got it?
I
I have the same problem. On the top of the screen only
Rather annoying isn't it ? I have it on the sides a bit too, it seems to be worse when the screen is hot. Possibly the joint between the "touch" screen and the frame.
I guess I'll take it back but I think the guys are going to look at me "sideways" over there ;-) It seems to me the quality of HTC phones has been going down a bit lately, prices stay high though. I wonder if all the Cruise devices aren't going to develop that problem over time...
Hi,
I've got a similar problem. It also happens when I firmly press X, but the noise comes from the back cover (the antenna-box ) and it's because the back cover (top, not the battery cover) is not stuck tight enough (left side, so right side if you're looking from the front). Annoying? Maybe. Deffective? Not really I'll live with it
i have the same issue with the screen, i have done about 20 minutes of "up close and personal" tapping, pushing, etc and it is definately the screen...
not so worrying right now, BUT if it is loose now, how will it be in a few months.
i had this same problem when buying a Nokia a while back, I went through 4 of them sitting in the store and they all had the same problem, so i gave up and bought a different phone.
i wonder how Devicewire will handle this? as i really dont want to, nor can i be without the phone for too long, but obviously i dont want a faulty unit.
Devicewire if you are listening out there can you advise?
So it seems there are a few of us with that issue, on mine it definitely comes from the front part, not the back. I think I'll take it back and try another one, if it has the same problem I'll pass on the Cruise and get a refund, it really isn't very acceptable to have that type of problem on a €500+ device ! I don't remember reading about any such problems with the Touch or Touch Dual, HTC must have skimped on the glue this time around!
I have triesd to reproduce the screen problems, but I do hear anything at all.
Overall I really like the device, notwithstanding the slightly slow graphics when watching video (although MUCH better than my old Samsung SCH-i730).
T
I have it too. I noticed it after putting on the screenprotecor...and i'm suspecting it has somthing to to with it. The protector is really stiff so it may just be it making that noise....in my case at least...
That might come into play I guess, but mine really had a problem, I took it back to the shop and I had a hard time getting the guys to acknowledge it, but one of them had his own Cruise and when I pressed on the side there was no squeaking at all so that sealed the deal. Unfortunately they had no spare unit so I had to settle for a voucher...
I too have been experiencing the same from the top of the screen after long use It´s a pain, as I am really happy with the Polaris but for the money you´d expect better. I removed the screen protector to see if that was the problem but the sound is still there. It only goes away after the screen has been off for a while.
I have spoken to the shop where I bought it but they said I should get in touch with HTC, however if a lot of devices have the same problem hardly seems worth sending it away....
Anyone else have the same problem???
christonge said:
I too have been experiencing the same from the top of the screen after long use It´s a pain, as I am really happy with the Polaris but for the money you´d expect better. I removed the screen protector to see if that was the problem but the sound is still there. It only goes away after the screen has been off for a while.
I have spoken to the shop where I bought it but they said I should get in touch with HTC, however if a lot of devices have the same problem hardly seems worth sending it away....
Anyone else have the same problem???
Click to expand...
Click to collapse
I Have the same problem but it comes from the screen protector, cuz I get some air between the screen and the protect.
OK... but the problem I have is definately not related to the screen protector as it´s still there without it.
No squeaks at all on the Orbit 2 - I wonder if it's confined to the TC case?
I've got the same squeeking thing with the screen, but it really isn't critical. What is really annoying is the knocking sound that the volume slider produces when shaked or just given a little finger punch. What do you guys say?Is yours fixed tight?
Same problem here. But it takes my mind off what the wife's saying when I'm on the phone to her!
Having the squeaking too, as most of you its still there without the protector
anybody get any noises from the d-pad? whenever i press left, it makes a double click (the standard click when you press in any direction, but after that, it seems to stick a little and click again as if it's sticking to something when i press down, then unsticks and makes a click when that happens). it's bugging the crap out of me and it only does it when i press left. if i press left hard, it stops doing it for 30 seconds or so.. it's not as if i spilled soda or anything on it and it is brand spanking new..
Hi all,
I have been using the wm series smartphone for a while. namely trinity, orbit and now orbit2/cruise/polaris.
I would like to know whether fellow orbit 2 users are having the same problem with the screen as I have.
The angle is fine from everywhere else except from top down towards the phone. Everytime i have to adjust the screen so that i am looking at it from bottom up to get a good view of the screen. When looking from top down, I get discolored views darken pictures. Any degree of top down angle, and the screen goes discolored. I have encountered this problem with lighting or no lighting conditions in the enviroment. So it is really irritating when taking pictures. And especially when I am watching movies.
I would like to know if there is a software fix for this or is it a manufacturing fault.So I can send the phone back for an exchange before its too late.
Hope you experts out there have an answer to my question!
Thank you so much.
i sent 2 orbits back due to screen being naff. both occasions the screen wasn't fitted squarely in device, so appeared off-centre. in all my browsing before i sent these back i couldnt find any apps to adjust screen (like you'd get on a topend lcd monitor).
i also noticed that viewing images/videos in landscape mode the screen had a shimmer across it, really weird. plus, the first two screens had like an oily slick between the membrane and screen,, not impressed at all, bad build quality too with stellar and orbit 2.
good luck! i'd send it back, and be prepared to send your next one back too !
badaas said:
i sent 2 orbits back due to screen being naff. both occasions the screen wasn't fitted squarely in device, so appeared off-centre. in all my browsing before i sent these back i couldnt find any apps to adjust screen (like you'd get on a topend lcd monitor).
i also noticed that viewing images/videos in landscape mode the screen had a shimmer across it, really weird. plus, the first two screens had like an oily slick between the membrane and screen,, not impressed at all, bad build quality too with stellar and orbit 2.
good luck! i'd send it back, and be prepared to send your next one back too !
Click to expand...
Click to collapse
Yo, badass, that is some bad decision we have made buying the orbit 2. I wonder why hasnt more people complained about the screen problem orbit 2 has. Or is it just a batch problem where, the manufacturing ran out of lcd stock and changed to a sh*tty lcd we have here. So the case might be we are have a bad batch of orbit 2.
I really dunno what to do, really am disappointed. Loved this phone so much. Done so much upgrades, modding, ultimate launch, S2U2 and everything to make it work like a nice working phone like iphone.
BesidesTHe touchscreen is not reponsive i think is a common problem to all polaris and orbit 2 users, sigh. So much hacking to do just for it to work properly. They should have done the hacking before hand. Dunno what the people at HTC/O2 is doing.
Anyone else has a good suggestion ?
Regards.
I just noticed today a rectangular area on my lcd screen where it looks like oil on water. It's basically a rectangle w/ a half inch border of the "Normal" screen. I can see it from any angle as well as when the phone is turned off. The phone and the touch screen both appear to be working fine. The distortion will react to pressure on the distored part of the screen as well. I'm thinking some moisture got in my phone some how (although I can't for the life of me think when I could've gotten moisture in there). Is there an easy way to fix this or should I call up ATT support to see about sending it in to have them fix it? What's the general next step? I'll post a pic when I get home to my camera. I've had the phone since the first of the year and am currently using EnergyROM 2.0.
Thanks a ton,
Patrick
I haven't seen anything like this before but if it it was you say its probably moisture inside or even oil. Wait a little and see if it clears up, failing that give AT&T a call.
Holy Crap
Dude i have the same problem with mine sometimes, and i thought i was the only one!!
Its almost like the LCD screen is getting some burn-in. Even on a black screen you can see the shadow of an image, using touch flow 3d/2d its about half of the slider bar on the bottom of the screen. Did you also notice that the screen is flickering VERY slightly in the same area, but not on the rest of the screen? You have to try REALLY hard to see it. Almost like when you use a camcorder to see a CRT monitor's refresh rate. I had a feeling from the beginning that it was moisture causing this, because i do have the bad habit of taking my phone in the bathroom when I shower. My LID has turned pink because of the steam.
What makes me think it could be screen burn-in, is that I always keep my backlight as bright as possible, and once i see this start happening, i can turn my phone off for a few minutes, turn it back on and it works just fine with no image shadow.
I actually have been thinking about using my insurance to get a new phone because of this, and making sure i don't shower with the new one.
It's a known issue of the phone. I was able to get mine replaced, but I had it less than 30 days. You should be able to manage to get them to replace it if you make them look up known issues with the phone.
Sorry for the inactivity, I've been spending my days pulling Cat 5e in attics and haven't had much computer time at work / energy at home - I'm going to get in touch w/ ATT sometime this week and see about arranging a replacement, I'll post my results.
i have the same problem. near the corners i see very slight flickering as if the refreshrate can't handle the tf3d.
it most likely because of the themes. when using all of those non-original themes, it' shaving to load all the images, causing it to have very very slight lag. maybe?
it's rediculous, with the price of this phone, you'd expect higher technology for the screen.
Your digitizer is touching the LCD because too much pressure has been applied to it, probably in your pocket.
What you are seeing are Newton's rings http://en.wikipedia.org/wiki/Newton%27s_rings
I think we're talking about two different problems here.
First, you have the rectangular area like the topic starter described and may indeed be what bubble said. However, they are not rings... its a true square (at least for me).
Second, you have the flickering issue. I have this myself sometime at the position of the menu bar. Opera seems to be the only app that triggers this for me though - then i get flickering Opera 'burn in' like effect. This will eventually disappear again after keeping the phone off for a few hours, then on with the screen off. This effect does survive soft-reset and such.
Newton's rings is the name of the observed optical phenomenon. It has nothing to do with it's shape.
I know that in this case it appears on a square section of the screen (I face the same issue and I already ordered a replacement screen).
Is there a solution to the flickering and screen burn problem? I didn't notice it until I had loaded a 6.5 rom and was using the light colored R&R theme. I could then see flickering in the bottom portion of the screen. Then I notice the screen burn of both soft keys.
It went away overnight with the phone off, but came back by the end of the day. It's really upsetting as I love this phone, but hate having something that isn't working right. Any suggestions?
I've had the same issue a couple of times although it wasn't nearly the entire screen. It was just a small blob in the very center of the screen. It happened because it was in my pocket. When it occurred initially it was summer (30-40 degrees celcius here in Perth) and would fix itself after about 5 minutes of being in my hot car (temperature hot, not awesome hot =D ). However (more recently - it's colder now) it stayed for half a day or so and only fixed itself after I sat it in front of the cars heating vents with the heater on for about 10 minutes (not too hot). I'm wondering if the digitiser separates from the LCD when heat is applied. It makes sense to me but I'm not sure I'd recommend anyone trying my solution ... especially if you've got the big square issue.
You also have to be aware that this phenomenon is only visible under artificial light.
That's why some people report it to disappear/reappear.
True ... but when the "phenomenon" disappears (i.e. as the lcd seperates from digitiser) it makes a clicking noise and the screen behind the blob flickers (like when you push on a normal LCD with your finger) indicating that the pressure of the digitiser pulling the screen upwards has been released. Once this has happened the blob has gone. It's not visible under ANY light.
If it happens again ... I'll get some footage.
I found another thread regarding the "Oil Spot" that comes and goes on the LCD that I'm experiencing if others are interested:
http://forum.xda-developers.com/showthread.php?t=475294
Oops - double post
Hi guys, I have the solution for you! I see burn-ins on my screen and I was able to get rid of them with a simple video that switches fast the main colors (Red Green Blue). Here is the link to the video:
http://www.youtube.com/watch?v=liMySLZkF5o
I have the video pulled from youtube as mp4, and 5 minutes of playing on full screen, the display got back to normal, clear and without any burn-ins.
If you need the mp4 vid, let me know so I can send it over (email)
Regards to All
Dear members,
I would like to know the truth behind the issues faced by the HTC one X, which I read in many websites across the internet(and few here)
I was decided to get one for me untill last week, but the issues what I read for one X confused me.The issues that I came across was;
over heating(guess its obvious for smart phones)
Wi-fi issues(death grip issue)
screen/display flickering,
yellow spots on display,
Frequent black screens,
Restart troubles,
Music player issues(when music player stops when gallery is used)
Taiwan made phone's facing issues over Chineese made ones.
Kindly address these issues ASAP, as I had already made up my mind to go for HOX, so that I can buy one with relaxed mind...
I cant think of any other smartphones as of now.
Thanks in advance
Arun J
India
I second this post and would really like to know how current owners are experiencing these issues.
Mine is a Rogers HTC One X.
Got it about 3 weeks ago. Just sent it in for repair, just outside the 14 day exchange range
overheating wise, yes, it can get a bit warm at use but same for any small tightly packed smartphone. I didn't have any wifi issues or any issues you had stated.
The problem with mine was holding the phone vertically. About half way down, there was a 1cm horizontal strip that did not react to touch. Just where the ok and cancel options pop up on some games/apps. You would need to rotate the screen so you could "tap" those buttons and get a reaction.
I turned on the developer mode and the mouse tracking/button press options and you can trace your finger down the screen and you can see where it stops then continues with a 1cm or so gap between where it wasn't responsive. This gap was the entire width of the screen not just a spot or two in that 1cm zone.
The phone was never dropped, bent, sat on etc. Mint screen and case, no case or touchscreen protection. This issue occurred quite suddenly about 16 days in, only noticed it when some games didn't let me exit when hitting the cancel options. Originally thought the game or the app was at issue. Then realized it was the touch screen. Did a full reset a few times, same problems. Now patiently awaiting for my phone back. Rogers phone/loaner suck as well, gave me a Nokia C3 POS as a loaner. Using my old motorola milestone instead.
Hello, guys.
Recently, I dropped my M2 on the street, resulting in cracked touchscreen and lcd. Replaced both the touch and the lcd, everything seemed normal until I noticed that the middle part of the touch (a line going from the left to the right, around 1cm height) doesn't work, it just doesn't respond. Later, I got another new touchscreen and same story - same part of the screen doesn't work.
Maybe we have some kind of defect touch screens here in Bulgarian stores? Though I bought the two touches from two seperate stores. Or it's possible that it's something with the lcd? Even though it works normally, no strange behavior, no black spots, scratches or anything. Or could it be a software problem? Using Android 5.0.
Thanks in advance.
More likely to be motherboard problem if it's the same with 2 different screens being installed
Thanks for your answer.
One thing I forgot to mention - when testing the screen in Sony's Sketch app or in the service menu, if I run my finger from the top to the bottom, or the opposite way quickly, sometimes, the lines my finger makes don't get cut, i.e. it's like the screen is functioning properly, with no dead spots. What does this mean?
According to Sony support, it could be a compatibility issue between the phone/touchscreen/LCD, what do you think?