After the squeaking back cover of the Touch Dual, another noisy HTC unit ! At least my test unit it seems...has anyone else noticed that when you tap at the top of the screen, say the x box, when you let it go there is a noise of something coming unstuck/unglued ?
If you swipe your thumb from let to right applying some gentle pressure it is event more obvious. Anyone else or is my screen maybe not properly glued on...
I listened really closely, and the only sound I could detect was my oily finger coming off the screen! You may have a defective unit because I don't seem to detect the problem you are talking about. Hope this helps!
Yes, thanks, will need to take it back then, just my luck !
You did apply some moderate pressure didn't you ? It's particularly noticeable around the loudspeaker and camera openings. Or it maybe static I'm hearing, doubt it since I don't have the noise at the bottom of the screen.
GpsPasSion
i tried several times but there's no noise.
Maybe u should check it with HTC or the store where u got it?
I
I have the same problem. On the top of the screen only
Rather annoying isn't it ? I have it on the sides a bit too, it seems to be worse when the screen is hot. Possibly the joint between the "touch" screen and the frame.
I guess I'll take it back but I think the guys are going to look at me "sideways" over there ;-) It seems to me the quality of HTC phones has been going down a bit lately, prices stay high though. I wonder if all the Cruise devices aren't going to develop that problem over time...
Hi,
I've got a similar problem. It also happens when I firmly press X, but the noise comes from the back cover (the antenna-box ) and it's because the back cover (top, not the battery cover) is not stuck tight enough (left side, so right side if you're looking from the front). Annoying? Maybe. Deffective? Not really I'll live with it
i have the same issue with the screen, i have done about 20 minutes of "up close and personal" tapping, pushing, etc and it is definately the screen...
not so worrying right now, BUT if it is loose now, how will it be in a few months.
i had this same problem when buying a Nokia a while back, I went through 4 of them sitting in the store and they all had the same problem, so i gave up and bought a different phone.
i wonder how Devicewire will handle this? as i really dont want to, nor can i be without the phone for too long, but obviously i dont want a faulty unit.
Devicewire if you are listening out there can you advise?
So it seems there are a few of us with that issue, on mine it definitely comes from the front part, not the back. I think I'll take it back and try another one, if it has the same problem I'll pass on the Cruise and get a refund, it really isn't very acceptable to have that type of problem on a €500+ device ! I don't remember reading about any such problems with the Touch or Touch Dual, HTC must have skimped on the glue this time around!
I have triesd to reproduce the screen problems, but I do hear anything at all.
Overall I really like the device, notwithstanding the slightly slow graphics when watching video (although MUCH better than my old Samsung SCH-i730).
T
I have it too. I noticed it after putting on the screenprotecor...and i'm suspecting it has somthing to to with it. The protector is really stiff so it may just be it making that noise....in my case at least...
That might come into play I guess, but mine really had a problem, I took it back to the shop and I had a hard time getting the guys to acknowledge it, but one of them had his own Cruise and when I pressed on the side there was no squeaking at all so that sealed the deal. Unfortunately they had no spare unit so I had to settle for a voucher...
I too have been experiencing the same from the top of the screen after long use It´s a pain, as I am really happy with the Polaris but for the money you´d expect better. I removed the screen protector to see if that was the problem but the sound is still there. It only goes away after the screen has been off for a while.
I have spoken to the shop where I bought it but they said I should get in touch with HTC, however if a lot of devices have the same problem hardly seems worth sending it away....
Anyone else have the same problem???
christonge said:
I too have been experiencing the same from the top of the screen after long use It´s a pain, as I am really happy with the Polaris but for the money you´d expect better. I removed the screen protector to see if that was the problem but the sound is still there. It only goes away after the screen has been off for a while.
I have spoken to the shop where I bought it but they said I should get in touch with HTC, however if a lot of devices have the same problem hardly seems worth sending it away....
Anyone else have the same problem???
Click to expand...
Click to collapse
I Have the same problem but it comes from the screen protector, cuz I get some air between the screen and the protect.
OK... but the problem I have is definately not related to the screen protector as it´s still there without it.
No squeaks at all on the Orbit 2 - I wonder if it's confined to the TC case?
I've got the same squeeking thing with the screen, but it really isn't critical. What is really annoying is the knocking sound that the volume slider produces when shaked or just given a little finger punch. What do you guys say?Is yours fixed tight?
Same problem here. But it takes my mind off what the wife's saying when I'm on the phone to her!
Having the squeaking too, as most of you its still there without the protector
anybody get any noises from the d-pad? whenever i press left, it makes a double click (the standard click when you press in any direction, but after that, it seems to stick a little and click again as if it's sticking to something when i press down, then unsticks and makes a click when that happens). it's bugging the crap out of me and it only does it when i press left. if i press left hard, it stops doing it for 30 seconds or so.. it's not as if i spilled soda or anything on it and it is brand spanking new..
Related
I know sounds a bit silly, but when I move my $750 TC the volume button on the left side seems to jiggle. It makes a noise like a cracker jack toy. It's annoying to me, but if any and everyone else notice I would not feel so bad about it.
ditto.
also the aluminum d pad scratches easily. hairline scratches..arggg
Mine is solid...
The same problem with my volume button. I was surprised when I discovered where that silly sound comes from. Not acceptable for such an expensive device.
Same problem with mine as well.
Yeah mine also is pretty loose
The same here...
Can only hear it slightly if you shake the device voilently. Can see it becoming a little looser over time.
I have the same experience in my TC too
same here !!!
Though I was the lucky one. Guess not.
I agree that this is totally unacceptable.
Looks like HTC just don't want to make a 100% perfect device. At least one little problem exists here or there (besides the driver issue).
same same on my damn cruise...
Same for me .. really a boring noise..
Mine too, actually noticed it right after I took it out of the box. Problem is I like this phone the most out of all of the ones I've had so far, so I tend to over look it.
HTC seems to love making loose devices. The TyTN II hard key face plate on the front is very loose too. Nice to know that selling my TyTN II to try and get away from shotty workmanship was for nothing as it seems to be following me.
yup it is a shame. my 555€ cruise sounds like a cheap toys.
Also the power button doesn't look that strong.
dara
Here as well....
Loose here as well, not THAT bad, yet loose. Does not make you feel very confident about its quality, does it?
.......
Actually my problem is that the bloody volume button is loose but is very hard to budge up or down so I can never do it when I am using the phone.
The slider seems to be very stiff. I tried to move it backwards and forwards to loosen it up but didn't help at all.
Same for me... a boring noise. It's true, it's not acceptable for an expensive device like the TC !
yess
Same problem???????????????? any solution ?
i just noticed the corner near the home button has a tiny bend that starts seperated from the layer beneath it....it looks like an old screen protector got a little bend in the corner but that is the surface of the phone!!! is there anyway to replace it or i cant do anything just waiting for it to come off?
it is ridiculous how an expensive phone like touch pro uses such low quality plastic that can actually get bend and i feel really helpless now =(
Yeah, mine is doing that too. Except it's on the "back" button side. It doesn't really affect anything. I'm just worried that if something gets caught on it, it might peel back further.
Nothing can make this phone suck though! It rules!!!
Yeah, unfortunately the TP/Diamond are suffering from some manufacturing defects, probably because it's a "new" design style for HTC. My TP has a touchscreen defect that conveniently showed up after the two-week return/exchange period.
Protective case, learn to love it.
Do you guys think they would be willing to replace a new case if i pay them?
My device shows the same behavior since this morning. Its about 1mm, so nothing to worry about and it seems to stick pretty well on the rest, thinking about rasping the edge off a bit to make it smoother
Is this getting worse on yours? Last post is 3 weeks ago .......
Any chance someone would post a picture of this? I'm thinking about the Fuze, but I can't stomach another HTC phone full of hardware flaws.
season007 said:
Do you guys think they would be willing to replace a new case if i pay them?
Click to expand...
Click to collapse
If it's really a defect, they should replace it without you paying them.
Considering that ATT offers a 1 year manufacture warranty. I can't see why you wouldn't be able to return the phone and get a replacement. It is obviously a problem with the design of the phone.
It wouldn't hurt to try and go to an ATT store and see if you can get a new FUZE!!!
Well, as we all know, HTC always claims that they don't know anything about the problems we address to them.
When I first complained to their support that I am having GPS lag, they told me I was the only one in the whole world suffering that problem, so it must be related to the software I installed.
Luckily they can not deny hardware problem so easily, as long as it is clear that there wher enot caused by misuse.
I don't have this particular problam, yet, but as I am already on my thrid TP (the first two had a defect hardware keyboard and black paint falling off), I would like to get some photo evidence of the users here, who unfortunately have the button part coming off.
That way we can show to HTC that more users have that problem, before we send back our devices, and maybe negotiate a direct replace, instead of rapair procedure, which takes up to 2 weeks.
season007 said:
i just noticed the corner near the home button has a tiny bend that starts seperated from the layer beneath it....it looks like an old screen protector got a little bend in the corner but that is the surface of the phone!!! is there anyway to replace it or i cant do anything just waiting for it to come off?
it is ridiculous how an expensive phone like touch pro uses such low quality plastic that can actually get bend and i feel really helpless now =(
Click to expand...
Click to collapse
My AT&T Fuze started doing the same thing after just two months. However, the bent plastic corner of the clear laminate was RAZOR sharp. My wife went to answer the phone and it resulted in a very serious slash to her cheek. This defect resulted in a very serious cut to her face!!
What is even more disappointing is that AT&T said that warranty does not cover this issue and said that the only way I was getting a replacement was if I paid the $125 deductible from the [email protected]*t insurance they scammed me on. I would have thought for $5/mo. I was completely covered.
The AT&T customer care rep was rude and not willing to help. A request to speak to his manager didn't get me far either. Even after I threatened to switch all 30 phones at my company back to Verizon Wireless they didn't seem to care.
At last I called HTC America directly this morning, explained my issue and they turned me over to a product specialist who told me that they know of no such issue. Despite my insistence they refused to replace the phone. Therefore, I WILL cancel all 30 lines my company has with AT&T and go back to Verizon...I hear the Samsung Omnia is not a bad smartphone!!
Hello everybody,
I want to tell you what happened to my Touch Pro this evening:
On the display (also if the device is off) appeared a small rectangle in the center (about 2x3 cm) made from bubbles. Well, not bubbles, I’m quite sure that are liquid crystal. If I put pressure with the finger the “bubbles” move and follow the pressure also out form the edge of this small rectangle)
As I can reach a decent camera I’ll post some photos of this rectangle.
The strange thing is that the device didn’t fall in ground, didn’t have temperature range; nothing hit it and so on. It was in my pocket well safe!!
If display is on the problem is quite invisible, if display is "black" or off... ....Grrrr!!!
Now, my questions:
1) Warranty is also for display?
2) How warranty works in Italy? Where should I ship the item? Which times?
3) If I have ship the device, sould I load the original rom & radio? Where can I find the rom?
Certainly, first thing I’m going to do Monday morning Is to call Italy HTC’s support number…
Thanks a regards,
Andrea
The "oil spot" problem isn't a broken display. It's the touch sensitive layer, which has been subject to too much pressure (carrying it in your pants pocket, etc). This has been happening on a bunch of Touch Pros and Diamonds. You should still be able to use it just fine, but touch sensitivity may get worse over time.
HTC may or may not be willing to replace it for you (and if so, they may or may not charge some kind of fee). Although it's just a hardware change, you should probably recover stock SoftSPL for warranty.
I have the "oil patch" problem with my Touch Pro. Unfortunately when I first noticed, HTC would not fix it for me, so I still have the oil patch on my screen, although everything still works fine so far. If it gets worse, I plan on buying a replacement LCD/touchscreen and replacing it myself:
http://mobile.brando.com.hk/prod_detail.php?prod_id=03799
I've noticed this problem on quite a few of the original touch / elf / 6900 phones, including my old personal phone which I used in this condition for many many months without every having any actual issues. It is strange but like you said: pretty much not noticeable when on and probably just best left alone unless it really bothers you.
I have the same spot but it is not causing any problems that I noticed but there is many who have this spot in the diamond forum.
today i also noticed this on my touch pro..i sort of fell asleep on it and i think i might have messed it up
i can see that oil spot that you mention but only if i tilt the phone at a certain angle and only if the screen is off.When the display is on i can see everything properly
The problem:
Touch function is messed up badly..i tested in notes application and sometimes when i press at a point X the dot appears somewhere else on the screen...Internet browsing is a pain in the ass like this...
i also noticed one thing..i took the stylus out, put the phone next to my ear and i tapped at the area outside the oil mark. I get the normal soft sound and pressure feeling as it should be.. When i do the same at the oil spot its rather hard feeling and sound..
i will contact HTC on monday and see what they say about it..
otherwise i will get a replacement for 159euros (inc installation) from pdatech...
Happened to my Fuze...
Happened to me too 60 days into owning it. I carry all my phones in my pocket, but have never had this problem. I brought it into the at&t store that I got it at and they never saw it either (it is only a few months old for them and have not had any complanints yet). They were going to replace it for me but were sold out. They had me call the warranty department and they replaced it with a refurbished unit (although all of their refurbished units are brand new as of this point because the phone is so new for at&t).
If you got your phone through at&t call warranty support and they will swap it out if the unit is under warranty (which being 2 months old at this point it will be).
This happened to my Fuze as well. I tried to call AT&T support and visit a corp store but they ruled it as physical damage, thus voiding my warranty. Apparently the "crystals" under the display are cracked/damaged, causing the rectangle. Who knows.
has anyone successfully sent a touch pro raphael to HTC repair shop to be repaired under warranty with this issue?? its really bothering me that i can see it and i feel like it will affect my phone eventually...
Add me to the list too.. I am going to try to get mine replaced through Sprint if it gets bad. I hope they know this is an issue/defect and not something like water damage
ez345 said:
has anyone successfully sent a touch pro raphael to HTC repair shop to be repaired under warranty with this issue?? its really bothering me that i can see it and i feel like it will affect my phone eventually...
Click to expand...
Click to collapse
I believe this is a design/quality issue. I posted about this same problem here some weeks back. HTC will not repair under warranty, paid in total 77 pounds to get this fix from them. I believe they are aware this is a problem because in the warranty book, screens are not covered even when its not your fault. They call it Newton ring .
Funny thing that a lot of people started noticing this issue very recently: as if a cheap component came to the end of its life cycle.. propably in my head only..
Anyway: I noticed this on my TP a few days ago and I'm going to drop my phone to the local service. It's the second time in just over 4 months.. crappy build quality really
also: Diamond users have had the same issue: http://forum.xda-developers.com/showthread.php?t=439410
Local HTC service got back to me: they're insisting that it's a 'mechanical fault, not covered by the manufacturers warranty'. Then it gets better: the estimated repair cost is 275 euros (that's roughly 355 USD) for the replacement of the display and front cover.
Naturally I'm going to challenge this as the oily patch appeared over night when the phone was sitting on a table.
not that im questioning what happened but personally i find it difficult to imagine how it can get the oil spot just by sitting on the table :S
normally you would expect this after exserting enough force on the screen. Personally that was my case. I sort of fell asleep on the phone and might have hit it on the metal edges of the bed..anyway i got mine replaced from pdatech.nl for ~170euros including installation costs..
Well if I had to venture a guess, I'd say that the 2h navigation on the night before took its toll on the display and during the night it just spread out and became visible..
how dodgy. I have been getting this problem, but funnily enough I thought it was due to air pressure, because it happened to mine when i was on the plane.
anyway i was just coming home from someplace real hot (40C), and it kept giving me the screen alignment problem for a few weeks, kept thinking i was pressing the top right corner of the screen regardless where I pressed. However, found that putting slight pressure on the screen for a few hours (i.e. a weight) fixed the screen alignment problem temporarily (for a few hours).
Anyway, just came back on the plane from someplace real cold (-10C), now the problem has ceased.
???? air pressure? or temperature variation?
I don't have the screen oil spot problem you guys have however.
Here's to it lasting a little while longer...
I asked for a more detailed report of the fault and the service just said that 'It's a fault defined as OOW (Out Of Warranty) by the manufacturer' and that there's nothing they can do but charge me for the repair. Note: they're not even putting the blame on me saying 'abuse/misuse'!
Now I'm going to go to the seller (expansys) and hope that they have some interest in keeping customers happy (and maybe have more business with them in the future!) and make things right (=fix my phone or replace it).
Wow, and I thought I was the only one. I've noticed the same oily stain after falling asleep on the phone. I've had it for a month now, and I've gotten used to it. It does not seem to affect the sensitivity or the accuracy on the touch screen. At least not in my case.
Does anyone have any experience replacing the touch screen by themselves? Is it a complicated operation? I would greatly appreciate a 10-step-guide on how to replace the screen, if it's going to be an issue over time.
disassembly guide
check out the wiki of xda click on service manuals and look for raphael. its on page 19 of the PDF
I noticed this issue on my Touch Pro today morning! I used my phone last evening and everything was fine. Now the touch screen doesn`t work at all. Great.
Same issue
I have also been victim of the oily patch.
I have had the Sprint Touch Pro since November and it just happened within the past 2 weeks.
Maybe this is due to not putting the screen protector on the phone.
I'm going to try visiting the Sprint Repair Center to replace it and then put the InvisibleShield Screen Protector on it.
hi!
This is my first post here. I have the following problem: yesterday my phone was fine...today not. Yesterday I was using the touch screen as usual with no problem, today the battery was to low and I turned off the phone. When I get back home, I connected the phone to charge it, and PUF!! the touch screen was not working at all...sometimes I can tap some menu, sometimes not, but in general terms, I can only use my phone with the keyboard. I did a soft and hard reset and nothing happened, I don´t know what else to do. I see this is kind of common problem, but no one has a common solution. Any suggestions?
Thanks!
My phone has windows mobile 6.1 Professional. CE OS 5.2.19971 (Build 19971.1.2.6)
ROM version 1.95.502.5 WWE
Radio version 1.02.25.32
Protocol version 52.39c.25.22H
u were able to use the windows 6.1 explorer? like looking for files under files explorer with no problem?
my phone is just as new as yours, i feel so frustrated! I was able just to use the keyboard, no touch screen commands were functioning. As i said, I have seen too many people complaining about this (if I would have known that, I would´nt buy this piece of crap)
dcgamboa said:
my phone is just as new as yours, i feel so frustrated! I was able just to use the keyboard, no touch screen commands were functioning. As i said, I have seen too many people complaining about this (if I would have known that, I would´nt buy this piece of crap)
Click to expand...
Click to collapse
At any time did you apply too much pressure on the screen?
Is your d-pad still working?
What about other hardware buttons besides the keyboard?
As I said, one day was working perfectly, and next day a kept it turned off since the battery was gone, and I was not at home to recharge it. So basically one day was fine and 12 hours later was not. The rest of the buttons are fine.
I did a hard reset, and at some point of the process the device indicates that I need to align screen, so a small cross show up in the middle of the screen (yo oughta know how is this...) well: I tap the cross and nothing happens....I tapped again...and nothing happens...3 tries later, finally the cross moves and the process goes on, To complete the process it takes me about 15 minutes!!!!!! but still nothing works out, the align screen process starts over again, and thats it!
At least, before the hard reset I was able to start my phone....now is impossible
Dont know what to do...
dcgamboa said:
As I said, one day was working perfectly, and next day a kept it turned off since the battery was gone, and I was not at home to recharge it. So basically one day was fine and 12 hours later was not. The rest of the buttons are fine.
I did a hard reset, and at some point of the process the device indicates that I need to align screen, so a small cross show up in the middle of the screen (yo oughta know how is this...) well: I tap the cross and nothing happens....I tapped again...and nothing happens...3 tries later, finally the cross moves and the process goes on, To complete the process it takes me about 15 minutes!!!!!! but still nothing works out, the align screen process starts over again, and thats it!
At least, before the hard reset I was able to start my phone....now is impossible
Dont know what to do...
Click to expand...
Click to collapse
well then you have several options:
1) bring phone back to the entity you purchased it from considering you stated it was new it should be covered under warranty unless you purchased it from eBay w/o warranty
2) If you know it is the Touch Screen then I suggest using xda search function and searching "Think your digitizer is broken" and apply it the Fuze rather than the Tilt
3) attempt to replace the screen
4) sell it "as-is" for a loss
Problem solved!!!
Thanks guys for the suggestions. This seems to be a very common problem. But in my case the solution was simpler than I would ever though!! I read in other posts that this unresponsive touch screen problem is usually created by particles of dust, (sand! in my case), stuck in that tiny gap between the screen cover and the phone body, and the solution was to gently pass a piece of paper thin enough, (flexible plastic CD cover, in my case) well....Having tested all kinds of software """solutions""", and been prepared to pay for an expensive fix (I live in Costa Rica, this kind of phones are not common use, so fixes are expensive)...so I gave I try to this solution...and surprisingly IT WORKED...there were lots of dust, and even sand grains stuck in that gap, and like the phoenix...my phone got back to life!
Its amazing how delicate are these devices!! I think they are intended for enclosed-temp-controlled-ultraclean places only.
I hope this helps a lot of people having the same problem.
Thanks!
dcgamboa said:
Thanks guys for the suggestions. This seems to be a very common problem. But in my case the solution was simpler than I would ever though!! I read in other posts that this unresponsive touch screen problem is usually created by particles of dust, (sand! in my case), stuck in that tiny gap between the screen cover and the phone body, and the solution was to gently pass a piece of paper thin enough, (flexible plastic CD cover, in my case) well....Having tested all kinds of software """solutions""", and been prepared to pay for an expensive fix (I live in Costa Rica, this kind of phones are not common use, so fixes are expensive)...so I gave I try to this solution...and surprisingly IT WORKED...there were lots of dust, and even sand grains stuck in that gap, and like the phoenix...my phone got back to life!
Its amazing how delicate are these devices!! I think they are intended for enclosed-temp-controlled-ultraclean places only.
I hope this helps a lot of people having the same problem.
Thanks!
Click to expand...
Click to collapse
awesome!!!! good job.
More info needed on "HTC fuze touch screen not working"
Hey, Ive tried following the thread about the htc fuze touch screen not working... up until the part about sand in 'some space between something...'
can someone provde more context/ pics? of where the sand might be.. because it sucks trying to use the fuze without a touch screen.
thanks for the help.
and the HTC customer support immediate went to the "well just hard reset the phone"... how quickly they are willing to erase all that data and hours of work to reconfig the phone..
any help is appreciated...
They were talking about the tiny gap between there the top layer of the screen (the material you touch) comes into contact with the body I believe. What you can try doing is running a piece of paper or something thing enough to wedge out the dirt in that area.
another somewhat common problem is the newton ring. You'll see an oily residue in the center area of your screen (it looks like rainbows). What I believe happens with this is your screen gets stuck to the actually LCD display underneath and doesn't bounce back to go back to it's resting state. What some people have said is to get some sort of adhesive material and use that to pull the screen up gently, so it goes back to resting. People have used tape and the such. Just be careful you don't pull the screen off your device.
Im wondering if other people's 8X's creak when squeezing the phone sideways or on the screen after a few minutes of use? Also I can see light leaking from the bottom where the screen meets the body of the phone. Want to know if I should get an exchange tomorrow at Microsoft Store since after that I'm pretty far from any Microsoft Stores until I'm past the return date.
My volume rocker squeaks a little and also moves back and fourth when I shake the phone. At the bottom of the phone on either side of the charging port there are light leaks, and on the left and right bottom sides too, which is annoying in the dark. Tempted to take mine back to Phones4u and ask for a new one..
Got a new phone and its much better. I didn't notice if light leaks through bottom anymore, but the screen is definitely more flush though not PERFECTLY flush.
Much more solid phone and power button also has a click and is easier to press now. No more creaks now.
Sent from my 8X using Board Express
I'll go and exchange mine then I think. Can you take a picture of it in the dark to show if you have any light leaks and post it up? I'd be very appreciative.
My power button feels a bit odd too, it doesn't have a click and feels squidgy, was thinking that earlier. Might have a go on the replacement in store and look at it in the dark to check for light leaks.
Edit: I've attached the best picture I could get of my light leaks/screen fitting. This is with brightness at max, taken with my DSLR. Was yours this bad? I'd be interested to see if this is an issue with other 8X's or just ours.
I haven't had any problems like that with mine yet. I started using a case after the first week though. Hopefully a replacement will fix the issue for you. That's a lot of light coming through.
Sent from my HTC 8x using Board Express
It is, it's awful. I'm kind of regretting getting the 8X over the 920 to be honest, the blacks seem very light on the screen and the colour seem very washed out (maybe it's just coming from an AMOLED screen that is doing it), might see what they can do for me in store today. We'll see.
Took it back today, they didn't want to replace it but they did in the end. Tried out two brand new Yellow ones in store, both had the exact same issue. Tried a black one, and it's perfect, no light leakage at all. Maybe it's an issue with the Yellow one. Poor effort HTC.
Accepted the Black one as a replacement, but I'm trying to sell it and get a 920 like I should have in the beginning. Doh!
SmokinWaffle said:
Took it back today, they didn't want to replace it but they did in the end. Tried out two brand new Yellow ones in store, both had the exact same issue. Tried a black one, and it's perfect, no light leakage at all. Maybe it's an issue with the Yellow one. Poor effort HTC.
Accepted the Black one as a replacement, but I'm trying to sell it and get a 920 like I should have in the beginning. Doh!
Click to expand...
Click to collapse
Meh. I have the black one and its an issue all right. Yesterday, my screen totally died. Went to HTC service center today, and the light leakage and inperfect screen flush were listed as "possible user damage". If they decide to classify it as user damage, i'll be pissed.
matthew5025 said:
Meh. I have the black one and its an issue all right. Yesterday, my screen totally died. Went to HTC service center today, and the light leakage and inperfect screen flush were listed as "possible user damage". If they decide to classify it as user damage, i'll be pissed.
Click to expand...
Click to collapse
I went with the 920, had screen flickering issues and random rebooting on it, and all 3 of my replacements. Gave up and got a Note II. lol.
Yes, when I had mine it creaked and the camera lens moved around a little, and the screen was a tad squishy on the bottom right...HTC consistently has awesome designs but
There is always something wrong with their build quality that is maddening.
Sent from my DROID RAZR HD using xda app-developers app
Crack over Speaker holes
Hi guys, just to add to the build quality problems... I've just had a replacement from Phones4U of my yellow 8X. After just under a month of gentle and careful ownership i noticed a crack appeared over (and through) the holes on the back for the speaker. The crack got bigger over about a week before i had chance to go ask about it in store. to be fair to P4U, the person i spoke to was great and they swapped it out in store, even though i'd originally bought it online.
Came back to this thread to mention it and now having read everything else i'm noticing a bit of creaking when i squeeze the sides and both phones had had the squishy screen edge picture thing which i first read about being a problem on the ONE X. Not sure if that's just normal anyway though really. Oh and neither of my power buttons have clicked and i find myself missing my easy to press home button on my old iPhone 3GS!
Same again!
natstally said:
Hi guys, just to add to the build quality problems... I've just had a replacement from Phones4U of my yellow 8X. After just under a month of gentle and careful ownership i noticed a crack appeared over (and through) the holes on the back for the speaker. The crack got bigger over about a week before i had chance to go ask about it in store. to be fair to P4U, the person i spoke to was great and they swapped it out in store, even though i'd originally bought it online.
Came back to this thread to mention it and now having read everything else i'm noticing a bit of creaking when i squeeze the sides and both phones had had the squishy screen edge picture thing which i first read about being a problem on the ONE X. Not sure if that's just normal anyway though really. Oh and neither of my power buttons have clicked and i find myself missing my easy to press home button on my old iPhone 3GS!
Click to expand...
Click to collapse
Well after a month (again) my replacement 8X has developed the crack in the same place.
Phones 4U are gonna swap it for a black model this time, i'm wondering if it's the yellow plastic specifically that's bad. They were less cheery and helpful with the exchange this time stating that because it's a cosmetic fault they don't usually replace them and the first time was 'a goodwill gesture'.
I'm starting to wish i'd just gone for the extra price bump for the Lumia 920 instead now. Guess i'm lucky they've replaced them at all though but i still don't think a phone should crack of it's own free will after 4 weeks! http://forum.xda-developers.com/images/icons/advanced/drive.png
They also said it's not a widespread fault that they've been made aware of, i was actually hoping someone else on here would have had the same experience to help me confirm it wasn't just bad luck or whatever. I guess everyone else just has the corners rubbing off instead!
I guess I got lucky, my blue 8X seems pretty solid and all the buttons are clicky.