Hi! I've got a problem with my phone: I want to go back to the original firmware with kdz updater, but it says ''phone not found''. My pc does not recognise lg p500 as a phone/smartphone but as a mass storage, usb composite device, disk drive, ADB single-sooner interface, etc...
I am running windows xp 32-bit.
I have installed all lg drivers, lg pc suite, etc.. but still no result. Please help!!!
Here's a log of kdz updater:
[R&D Test Tools Log File]
14:30:34 : Launching SW update
14:30:34 : Unpacking KDZ
14:31:04 : KDZ file extraced
14:31:11 : Files were extracted.
14:31:11 : LGMobileDL Load.
14:31:11 : Port = -1
14:31:11 : Connecting to phone
14:31:11 : PHONE WAS NOT FOUND!
14:31:13 : ===FINISHED===
Try these drivers.. disable lg modem in device manager while using kdz.
It didn't worked. I have disabled lg modem and i got the same message from kdz. Should i uninstall all other drivers (including pc suite) and install just the one you gave me?
EDIT: when i first plug it in (without ANY drivers) it is recognised by pc as lg-p500 but after installing drivers it is recognised as other things (i have mentioned ''the things'' in the first post).
Guess you can get some help from this thread...
forum.xda-developers.com/showthread.php?t=1827723
Sent via O1 running PA 2.52 by Bytecode.
I finally got it!!! It seems that lg drivers for lg p500 only support gingerbread os, not higher. So i have installed a gb android version, I installed the drivers using lg support app and suddenly: Found new hardware:
LGE android platform
I tried to install original firmware using kdz updater and..........IT WORKED!!!
I am so happy!!! So remember: IF YOU WANT TO INSTALL ORIGINAL FIRMWARE ON YOUR BELOVED LG P500 YOU SHOULD FIRST INSTALL A GB CUSTOM ROM!!!
Same problem happens with bluetooth too. when i pair phone to laptop it shows as unknown device. But if i install gb rom and then pair it shows up as phone.
Related
I'm a bit confused regarding the USB drivers for ICSSGS Beta 2 - http://forum.xda-developers.com/showthread.php?t=1362092
As I expected, after installing this rom and plugging my phone into my PC it fails to install the drivers. On the downloads page there's a "usbdrivers" file, which I've downloaded but contains only .INF's and .cat files and stuff. I've tried using the update through device manager method, but it doesn't work. Any idea on how I can install these drivers?
Hello! I tried to update my LG Optimus Me P350 with KDZ Update tool, but the update was unsuccesfull and now the phone is stuck in emergency mode. I can't use any combination of buttons, even when i connect to my pc, this thing remain stuck in emergency mode. What can I do?
Same for me :-(
I found a solution and it's working:
1.Download KDZ updater and uncompress it
http://www.4shared.com/file/UleS4dP3/KDZ_FW_UPD_EN.html
2.Install msxml.msi from the uncompressed directory
3.Charge your battery to almost full state (I'm not sure, but it can be reason if phone doesn't start)
4.Turn phone off somehow (remove battery etc.)
5.Install drivers properly•Get rid of all usb drivers like Nokia, microsoft visual ++ run time environments
•Install the LG drivers by selecting the update manager from the lg site
•Disable LGE Virtual Modem. In your Windows operating system, go to Control Panel > System > Hardware > Device Manager > Modems > Right click on LGE Virtual Modem and click Disable.
6.Press and keep pressed "Volume up"+"Return" and connect USB cable to phone
7.Yellow screen with text emergency mode should appeared
8.Shake the handset (I know, it sounds ... strange, but it helps for ones, so... why don't try it?) UPDATE: Read some quotes on bottom.
9.Run KDZ_FW_UPD.exe (Has administrator).
Select Type : 3GQCT (I have one report that CDMA mod works too)
Select PhoneMode : DIAG (in case of fail try EMERGENCY, and as last chance use CS_EMERGENCY)
10.I Recommend do not switch phone off. There was some people, which done it and after they were not be able to turn it on again. If flashing failed, just select some another mode and try it again, again, try shake/connect disconnect, again, again....
11.In KDZ file : Choose the ROM file you downloaded in the first step
12.Press Launch software update
13.Shake the handset (I know, it sounds ... strange, but it helps for ones, so... why don't try it?) UPDATE: Read some quotes on bottom.
14.Make sure that all update was done successfully. Phone should restart itself automatically
15.Disconnect the USB cable from the phone
16.Press the three button combo for HW reset of device i.e volume up + home + power button
KDZ firmware for LG Optimus Me P350:
LG Optimus Me Official Firmwares V10C Download
•[ASEABK] http://csmg.lgmobile.com:9002/LGP350/V10c_00/V10C_00.kdz
LG Optimus Me Firmwares V10E Download:
•[ACISSV] http://depositfiles.com/en/files/4y603iksc
•[ABALSV] http://depositfiles.com/en/files/4vh72o8kn
LG Optimus Me Official Firmwares V10F Download:
•[ACISSV] http://csmg.lgmobile.com:9002/LGP350/V10F_00/V10F_00.kdz
•[ABALSV] http://csmg.lgmobile.com:9002/LGP350/V10F_00/V10F_00.kdz
LG Optimus Me Flasher Tools Download:
•B2C: http://csmg.lgmobile.com:9002/client/app/B2CAppSetup.exe
•KDZ FW Updater: http://www.unclenet.de/files/KDZ_FW_UPD_EN.7z
What i did my phone is i reprogram it
That worked?
link for kdz flash file is not working can u plz update the link
Hi guys, first of, i want to thank the one who made the thread on how to uninstall SuperUSer using terminal apk with codes.
that was my 1st problem on how to remove that SU. 2nd is on how to reflash my LM me p350 software.
i followed the instructions.
How to flash LG Optimus Me Steps:
1. Install the USB drivers and LG B2C Tools
2. Unzip KDZ_FW_UPD_EN.7z and installed msxml.msi
3) Shut down the LG Optimus Me, remove the battery and connect the USB cable holding down the Volume Up button and wait until the drivers are installed (the phone should be on the "S/W upgrade Please wait" state while upgrading!!!!)
or
3′. Enable USB debugging and connect USB cable to your LG Optimus Me
4. Open your device manager and disabled under the Modem LGE Mobile USB Modem
5. Starts KDZ_FW_UPD.exe
6. In the Software Updater select "Type"=CDMA , "PhoneMode"=DIAG, and at "KDZ file" select the desired file. (The firmware .kdz file must have the name in this form!)
This will open "Read phone information" window. IN THAT WINDOW:
7. Click "Upgrade start". DO NOT CLICK ANYTHING ELSE BEFORE!
LG Updater launches…..
8. Select Country="Different country" (unless you are in Korea) and Language as you wish
LG Mobile Updater Launches………. warning you and asking your permission to continue..
9. Follow LG Mobile Updater instructions…
Let the tool running for a few minutes through and be pacient!!
ATTENTION!!
After the phone reboots first time, DO NOT UNPLUG USB CABLE!!!
WAIT!! Remove USB cable only after the log says that the flash was OK!
10. The flashing process is now finished.
i downloaded the V10F although mine is V10B Feb 22,2011.
i'm good to go, and i'm on #7, unpacking KDZ, and then Cannot find PHONE!
before that, when i plugged my phone and used usb debugging, there's now the big problem that's why the updater didnt detect the phone because of this : "Unable to install Driver Software".
How can i fix this problem, for me to flash my phone, i can't flash it if my PC/laptop can't detect my phone.
i would really appreciate a quick help. LG service center here is 4 hour road trip. back and forth hat would be 8 hours. so i'll ask for help first here. thanks.
Please some quick help about this, i've search about this but no clear guides we're given, i've installed the possible USB drivers for my PC laptop to read my LG me, but none of them worked.
hi,usb debugging of my p920 is out of order 1 month ago,even mass storage can not show on computer,tried win7 and XP same,
im a chinese user,sorry for my english,problems:
1.can not install apps with pc client
2.Device manager shows "LGE MOBIL SERIAL PORT" and “LGE MOBIL USB MODEM”
3.could flash device with "LG FLASH TOOL" BIN format rom and baseband
4.could not upgrade KDZ rom because when I plug the usb line p920 opens directly not charging as power off,even without battery !
5.official LG mobil support tool can not work.
6.after flashing with LG FLASH TOOL,device is not roored,no recovery,so....
7.device manager some times shows"2CDCs data interface " no driver,
is this hardware problems or software,and suggestions?
thanks guys.
no reply.......
Are your drivers installed?
Sent from my LG-P920 using XDA
Optimus vu here to use..
Vu firmware
http://csmg.lgmobile.com:9002/LGF100L/ALGTBK/F100L29i_00/F100L29i_00.kdz
How to Flash the LG Optimus Vu
Procedure to flash LG Optimus Chic:
First of all you need to download Downloaded the original firmware from here.
Then download the firmware updating software KDZ_firmware_updater and extract it to a folder. Install msxml on your windows pc by double clicking it.
Charge the phone to the maximum.
Enable USB Debugging on Phone (Settings/Applications/Development/), connect your phone to PC and wait for drivers to install.
In the software window, select Type as 3GQCT
Select PhoneMode as DIAG
In the ‘KDZ file’ space, browse for the firmware you want to install. (In this case V10A_00.kdz)
Click “Launch software update”
The firmware flashing process is now underway. If all goes well, in 5-10 minutes the phone will be flashed with the new firmware.
After booting up fully, detach the phone from the pc.
And your point is?
Edit: Your edit justifies a thread
?
¿
Thread moved to its correct location.