Hello! I tried to update my LG Optimus Me P350 with KDZ Update tool, but the update was unsuccesfull and now the phone is stuck in emergency mode. I can't use any combination of buttons, even when i connect to my pc, this thing remain stuck in emergency mode. What can I do?
Same for me :-(
I found a solution and it's working:
1.Download KDZ updater and uncompress it
http://www.4shared.com/file/UleS4dP3/KDZ_FW_UPD_EN.html
2.Install msxml.msi from the uncompressed directory
3.Charge your battery to almost full state (I'm not sure, but it can be reason if phone doesn't start)
4.Turn phone off somehow (remove battery etc.)
5.Install drivers properly•Get rid of all usb drivers like Nokia, microsoft visual ++ run time environments
•Install the LG drivers by selecting the update manager from the lg site
•Disable LGE Virtual Modem. In your Windows operating system, go to Control Panel > System > Hardware > Device Manager > Modems > Right click on LGE Virtual Modem and click Disable.
6.Press and keep pressed "Volume up"+"Return" and connect USB cable to phone
7.Yellow screen with text emergency mode should appeared
8.Shake the handset (I know, it sounds ... strange, but it helps for ones, so... why don't try it?) UPDATE: Read some quotes on bottom.
9.Run KDZ_FW_UPD.exe (Has administrator).
Select Type : 3GQCT (I have one report that CDMA mod works too)
Select PhoneMode : DIAG (in case of fail try EMERGENCY, and as last chance use CS_EMERGENCY)
10.I Recommend do not switch phone off. There was some people, which done it and after they were not be able to turn it on again. If flashing failed, just select some another mode and try it again, again, try shake/connect disconnect, again, again....
11.In KDZ file : Choose the ROM file you downloaded in the first step
12.Press Launch software update
13.Shake the handset (I know, it sounds ... strange, but it helps for ones, so... why don't try it?) UPDATE: Read some quotes on bottom.
14.Make sure that all update was done successfully. Phone should restart itself automatically
15.Disconnect the USB cable from the phone
16.Press the three button combo for HW reset of device i.e volume up + home + power button
KDZ firmware for LG Optimus Me P350:
LG Optimus Me Official Firmwares V10C Download
•[ASEABK] http://csmg.lgmobile.com:9002/LGP350/V10c_00/V10C_00.kdz
LG Optimus Me Firmwares V10E Download:
•[ACISSV] http://depositfiles.com/en/files/4y603iksc
•[ABALSV] http://depositfiles.com/en/files/4vh72o8kn
LG Optimus Me Official Firmwares V10F Download:
•[ACISSV] http://csmg.lgmobile.com:9002/LGP350/V10F_00/V10F_00.kdz
•[ABALSV] http://csmg.lgmobile.com:9002/LGP350/V10F_00/V10F_00.kdz
LG Optimus Me Flasher Tools Download:
•B2C: http://csmg.lgmobile.com:9002/client/app/B2CAppSetup.exe
•KDZ FW Updater: http://www.unclenet.de/files/KDZ_FW_UPD_EN.7z
What i did my phone is i reprogram it
That worked?
link for kdz flash file is not working can u plz update the link
Hi guys, first of, i want to thank the one who made the thread on how to uninstall SuperUSer using terminal apk with codes.
that was my 1st problem on how to remove that SU. 2nd is on how to reflash my LM me p350 software.
i followed the instructions.
How to flash LG Optimus Me Steps:
1. Install the USB drivers and LG B2C Tools
2. Unzip KDZ_FW_UPD_EN.7z and installed msxml.msi
3) Shut down the LG Optimus Me, remove the battery and connect the USB cable holding down the Volume Up button and wait until the drivers are installed (the phone should be on the "S/W upgrade Please wait" state while upgrading!!!!)
or
3′. Enable USB debugging and connect USB cable to your LG Optimus Me
4. Open your device manager and disabled under the Modem LGE Mobile USB Modem
5. Starts KDZ_FW_UPD.exe
6. In the Software Updater select "Type"=CDMA , "PhoneMode"=DIAG, and at "KDZ file" select the desired file. (The firmware .kdz file must have the name in this form!)
This will open "Read phone information" window. IN THAT WINDOW:
7. Click "Upgrade start". DO NOT CLICK ANYTHING ELSE BEFORE!
LG Updater launches…..
8. Select Country="Different country" (unless you are in Korea) and Language as you wish
LG Mobile Updater Launches………. warning you and asking your permission to continue..
9. Follow LG Mobile Updater instructions…
Let the tool running for a few minutes through and be pacient!!
ATTENTION!!
After the phone reboots first time, DO NOT UNPLUG USB CABLE!!!
WAIT!! Remove USB cable only after the log says that the flash was OK!
10. The flashing process is now finished.
i downloaded the V10F although mine is V10B Feb 22,2011.
i'm good to go, and i'm on #7, unpacking KDZ, and then Cannot find PHONE!
before that, when i plugged my phone and used usb debugging, there's now the big problem that's why the updater didnt detect the phone because of this : "Unable to install Driver Software".
How can i fix this problem, for me to flash my phone, i can't flash it if my PC/laptop can't detect my phone.
i would really appreciate a quick help. LG service center here is 4 hour road trip. back and forth hat would be 8 hours. so i'll ask for help first here. thanks.
Please some quick help about this, i've search about this but no clear guides we're given, i've installed the possible USB drivers for my PC laptop to read my LG me, but none of them worked.
Hi! I've got a problem with my phone: I want to go back to the original firmware with kdz updater, but it says ''phone not found''. My pc does not recognise lg p500 as a phone/smartphone but as a mass storage, usb composite device, disk drive, ADB single-sooner interface, etc...
I am running windows xp 32-bit.
I have installed all lg drivers, lg pc suite, etc.. but still no result. Please help!!!
Here's a log of kdz updater:
[R&D Test Tools Log File]
14:30:34 : Launching SW update
14:30:34 : Unpacking KDZ
14:31:04 : KDZ file extraced
14:31:11 : Files were extracted.
14:31:11 : LGMobileDL Load.
14:31:11 : Port = -1
14:31:11 : Connecting to phone
14:31:11 : PHONE WAS NOT FOUND!
14:31:13 : ===FINISHED===
Try these drivers.. disable lg modem in device manager while using kdz.
It didn't worked. I have disabled lg modem and i got the same message from kdz. Should i uninstall all other drivers (including pc suite) and install just the one you gave me?
EDIT: when i first plug it in (without ANY drivers) it is recognised by pc as lg-p500 but after installing drivers it is recognised as other things (i have mentioned ''the things'' in the first post).
Guess you can get some help from this thread...
forum.xda-developers.com/showthread.php?t=1827723
Sent via O1 running PA 2.52 by Bytecode.
I finally got it!!! It seems that lg drivers for lg p500 only support gingerbread os, not higher. So i have installed a gb android version, I installed the drivers using lg support app and suddenly: Found new hardware:
LGE android platform
I tried to install original firmware using kdz updater and..........IT WORKED!!!
I am so happy!!! So remember: IF YOU WANT TO INSTALL ORIGINAL FIRMWARE ON YOUR BELOVED LG P500 YOU SHOULD FIRST INSTALL A GB CUSTOM ROM!!!
Same problem happens with bluetooth too. when i pair phone to laptop it shows as unknown device. But if i install gb rom and then pair it shows up as phone.
Hi.. I just saw the new TWRP and liked it alot!. So i downloaded the TWRP for Trebon and also downloaded the Odin3 on my pc. And then i put my phone into the download mode and connected by USB. But the ID COM box wont come up.. The ODIN3 is just not detecting my phone .. Dunno why..
I tried installing drivers for my phone but it didnt work.
I also installed Kies after that but no use.. I used 2 versions of Odin3 i.e. Odin3 v1.85 and Odin3 v3.x.. But still its not detecting my phone..
So can anyone pleazz help!!
(Using SGA+ with the cm10)
are you sure you installed the drivers
* disable or remove kies
* Install drivers again (windows) select correctly 32/64 bits
or try this simple method.
INSTALLATION 1:
0. Uninstal previous Samsung USB drivers from Control Panel and Device Manager.
1. Unpack the .rar archive and run the installer from "SAMSUNG_USB_Driver_for_Mobile_Phones_v1.5.20.0\setup.exe" and proceed with the installation steps.
2. Switch your Samsung phone into download mode
3. Connect it to your computer via USB cable.
4. If your phone is still not correctly recognized by Odin - try the second method.
INSTALLATION 2:
0. Uninstall previous Samsung USB drivers from "Programs And Features" and "Device Manager".
1. This is the "have disk" method. You have to follow every step in this guide.
2. Unpack SAMSUNG_USB_Driver_for_Mobile_Phones_v1.5.20.0.rar to some location, eg. C:\.
3. Switch your Samsung phone into download mode.
4. Connect it to your computer via USB cable.
5. Your phone should become discovered by Windows as some device. In my case, Windows has found my SGS i9000 as a "Gadget Serial" device.
6. Go to Windows Device Manager. Right click on the device your phone has been discovered as (eg. "Gadget Serial" in my case) and choose "Update driver" option from the context menu.
7. Choose "Search my Computer...", check "Include subfolders" option and point the updater to the folder where you've had unpacked the drivers .rar archive to, eg. C:\SAMSUNG USB Drivers for Mobile Phones (x86 & x64) v1.5.16.0.
8. The driver should install automatically.
9. It may happen that after the installation some new "unknown device" ("Samsung Modem" in my case) would appear in the Device Manager. Complete 6 & 7 step for that device and any other new device that may appear afterwards.
10. Restart your computer.
11. Done!
drivers link (latest)
source - this helpful thread
Did all that.. but still when i connect my phone via usb , the pc detects it but not ODIN.. Can it be because of the custom rom ??
Suyash1996 said:
Hi.. I just saw the new TWRP and liked it alot!. So i downloaded the TWRP for Trebon and also downloaded the Odin3 on my pc. And then i put my phone into the download mode and connected by USB. But the ID COM box wont come up.. The ODIN3 is just not detecting my phone .. Dunno why..
I tried installing drivers for my phone but it didnt work.
I also installed Kies after that but no use.. I used 2 versions of Odin3 i.e. Odin3 v1.85 and Odin3 v3.x.. But still its not detecting my phone..
So can anyone pleazz help!!
(Using SGA+ with the cm10)
Click to expand...
Click to collapse
seems to be driver issue
try to connct with other pc or laptop
see whether pc detect it or not
Suyash1996 said:
Did all that.. but still when i connect my phone via usb , the pc detects it but not ODIN.. Can it be because of the custom rom ??
Click to expand...
Click to collapse
boot your phone to download mode normaly by pressing the key combo, not from twrp and should recognized.
Had the same issue.Gl
Thanks.. but.. i guess it was a problem wid d rom.. i flashed another one and it wurkd!
Hi Friends,
This is my first post at XDA.
I unfortunately bricked my Panasonic P81 after rooting it and adding XHalo app and the boot manager app from the Xposed Framework.
The situation is as follows-
I can get to the logo, it screams Panasonic and then doesnt boot. I dont have CWA installed and worse, my SD card which had my stock backup is also lost. This means I need a mechanism to stock recover and perhaps flash boot.img and recovery.img?
I am stuck at this point, not sure how to proceed. I can get to recovery, have cleaned cache, backed up user data ,done a factory reset. Even after factory reset it still cant boot.
Please help me with a step-by-step instruction to recover, this phone is dear to me. How do I flash?(boot.img or rom) I have downloaded Sagar Patel's (good bless him!) backup and the images, but need guidance on how to flash and recover.
Please help friends and apologies for any incovenience. I am still a newbie
Guys please help!!
Driver-USB-PC connection problem
kartik.krish said:
Guys please help!!
Click to expand...
Click to collapse
Hope drivers are installed properly in your pc.
If you are going to use sp flash tool, Make sure SP flash tool is set to auto-detect com port, not manual selection
If you find that it is driver problem, following may help you.
Please note that there is nothing that much hard in driver installation as it is just to connect your device with your pc but because many users still face problem of driver installation, you can try following tricks!!!
It is observed by me that driver installation and adb interface problem do not happen in windows XP as eventually and generally it is happened in windows 7 and later…so, you can simply try on windows xp if you are able to do so…(you can use dual operating system too!!! Or good relation with neighbor/friends/colleagues/someone/all can be beneficial here!!!)
Note that all tricks here are not necessary to work, but it may still work for you….
Take one by one step, if the first step does not work for you, only then try next step. This is not all steps to be taken at once type guide…This is simply Try and error type tutorial/tricks…
There are following problems I have come to know regarding to driver installation and conflicts:-
Device is charging through usb cable but there is no usb option displaying on either device or no driver installation box/message/pop up appears in pc….
Missing sound of that usb-pc connection
Sound of disconnection after couple of seconds of connection
Adb interface is missing
Ok, sometimes changing usb connection type for example, from mass storage or mtp to camera, ptp, usb tethering or something else can bring adb interface…..
Try with different USB Cable. You can use original nokia or samsung tiny cable instead of cable having long length. Sometimes, length matters!!!!
Try in different USB Port.
Sometimes, you have to disable signature verification in your pc for proper installation of driver.
Had you disabled your antivirus before downloading, installing and while running your tools/softwares? You may need to do so…
Have you installed the software (or say, all associated softwares/tools) in C-System drive?, if not, then you should first install required software/tools in system drive that is usually C drive in Microsoft-Windows OS…or try after installing them on desktop.
Keep all necessary files/tools (driver files, flash tools, rom etc…) on desktop.
Download proper driver According to your model/device, According to chipset inside, According to Official site of manufacturer, Official site of chipset, through PC Suite/flash program of your device…
If the problem still not solve, you should try all available driver packages of your device one by one whether from official site of chipset inside your device, or any forum, adb, pdanet+ or foxfi, universal driver, VCOM Port driver, drivers from hexamob through play store, and find all possible packages and see if someone make positive result after installation…
If the problem still not solve, you should install remaining update packages of your system (PC) including all primary, secondary, essential, Non-essential updates….whatever, just install them all….reboot your pc…and see if problem is solved….
If you can connect the device but somehow found that device driver still not installed properly, just go to device manager in your pc, click on portable device, right click on your device and apply “Update driver”. Click on “automatically search” when a window prompt ask you.
If the problem still persists then,
Just remove all the drivers using usbdeview (I have given link also to download usbdeview in earlier post)
https://drive.google.com/folderview?id=0B511A2txfpAPbmwtQXZqbnVlT1U&usp=sharing
Install usbdeview and remove all the drivers
You can also fix this by showing the nonpresent devices in devicemanagement (google for show nonpresent devices for explanation)
Go to com ports, and delete all mediatek drivers except preloader driver. Now start over. It can help if you choose the same usb port where you had success last time.
Use Usbdeview to uninstall all the drivers before connection, restart the pc, Extract and keep driver zip files and other useful files/tools on desktop…just start your tool… and try to perform your tasks like backup…or restoring the backup…without worrying about that sound of disconnection you may listened after couple of seconds of connection or don’t even worry if you are just missing that sound of usb-pc connection….just try on your tool…
If still problem of driver installation persists, then simply use usbdeview and uninstall all drivers, restart your pc and try following steps:-
There are various ways to install proper drivers at the time of connecting the device with pc depending upon how you connect it.
Follow the procedure both with and without battery
Simply plug in via USB Cable
Connect by holding volume down button
Connect by holding volume up button
Connect by holding Power button
Connect by holding power and volume down
Connect by holding power and volume up
Connect by holding both volume up and down button
Connect by holding thrice volume up, down and power button
Connect by holding power and home button
Connect by holding power and menu button
Remember which method works and which drivers are installed
in LAN-Devices you may have different android device
Select/set drivers by hand and use the mtk usb driver, now Flashtool finds the phone
Suppose holding volume down method without battery works for you then what next you have to do is as below:-
1.TAKE THE BATTERY ,SD ,SIM OUT OF THE PHONE
2.HOLDING VOLUME DOWN CONNECT IT TO PC VIA USB(ONCE YOU HEAR A SOUND FROM PC YOU CAN RELEASE VOLUME DOWN)
3.OPEN DEVICE MANAGER(ON COMPUTER SEARCH IT OR CONTROL PANEL)
4.WAIT FOR 2-3 MINUTES
5.YOU WILL HEAR A SOUND & OTHER DEVICE WILL BE DISPLAYED
6.IN OTHER DEVICES ->MT65XX PRE-LOADER
7.RIGHT CLICK MT65XX PRELOADER
8.UPDATE DRIVER
9.LOCATE THE DRIVERS PROVIDED ACCORDING TO YOUR OS(VISTA,WIN7,XP)
10.IT WILL DO ITS STUFF
Install Mediatek drivers, preloaders, VCOM port etc…
Manually Install MediaTek USB VCOM Drivers
Requirement:-
1. Download MediaTek USB VCOM Drivers
2. Download USBDeview
Here is the link from you can get it:-
https://drive.google.com/folderview?id=0B511A2txfpAPbmwtQXZqbnVlT1U&usp=sharing
Procedure
(* Note: You might need to disable drivers signature verification in Windows for this to work smoothly.
If you want to turn off device driver signing in Windows completely, do the following.
Windows 7:-
1. Hit the Win+R keys together to open the run dialog
2. Type gpedit.msc to open the local groups policy
editor
3. Expand ‘Administrative Templates’ (it’s under ‘User Configuration’)
4. Expand ‘System’. Click ‘driver Installation’
5. In the right panel, double click on ‘Code Signing for Device Drivers’
6. Choose ‘Enabled’ in the window that appears.
7. In the underlying options, choose ‘Ignore’
8. This disables drivers signing in Windows 7, and now you can install unsigned drivers in Windows 7.
9. Click Apply, OK. Restart your computer to install unsigned drivers
Windows 8
1. Hold down the Windows key on your keyboard and press the letter C to open the Charm menu, then click the gear icon (Settings)
2. Click More PC Settings
3. Click General
4. Under Advanced Startup, click Restart Now
Note: In Windows 8.1, the ‘Restart Now’ button has moved to ‘PC Setting -> Update & Recovery -> Recovery.’
5. After restarting, click Troubleshoot
6. Click advanced options
7. Click Windows Startup Settings
8. Click Restart
9. After restarting your computer a second time,
choose Disable driver signature enforcement
from the list by typing the number 7 on your Keyboard Your computer will restart automatically.
10. After restarting, you will be able to install
unsigned drivers normally; however, Windows
will display a warning message. When the
warning appears, click Install this driver
software anyway. )
1. Install USBDeview and use it to uninstall all Vcom, Mediatek and Preloader drivers
1b. Extract the contents of the Mediatek USB VCOM file
2. In Windows, go to Control Panel and open Device Manager
3. Click any of the device groups (any of the items on the list) you see there, and then from Action menu, select Add legacy hardware
4. Add hardware wizard will be opened, click next
5. Select Install the hardware that I manually select from a list (Advanced)
6. Click next two times and click Have Disk button
7. Click browse and find where your driver's .inf file is, then select it (the .inf you'll select is located in drivers > USB Vcom driver > your OS) . Ensure to select the 64 bit .inf if your PC is 64 bit
8. Click Open and OK. You will see the drivers listed.
9. Select your driver there (select Mediatek Preloader USB VCOM Port)
10. Click Next and finish installing
11. If SP flash tool or other software still dont detect your phone then also install Mediatek DA VCOM (consider installing more from the list of drivers one at a time if need be)
Try in different PC
Sometimes windows XP works when windows 7 fails!!!
Case:-
It did the same thing with my MT6577 (Wiko Cink PEAX), so I connected it with a battery and without holding VOL+. Then "MT65xx preloader" appeared in device manager then disappeared (once). It is normal that it disappears. When you start Flash_tool and when you click Download (or whatever you want to do) THEN you connect the phone (in off state), and the flash operation will succeed.
Guess what? Once my Panasonic P81 could install driver and got detected after approx. 5 hours of continuous connection with win 7 x64!!! Meanwhile, I tried first usbdeview and then manually installation of mediatek driver but manual installation had failed as my p81 was only charging when it was connected with pc….So, mediatek – windows 7 conflicts….but, when I tried tiny (very small) nokia usb cable, it works instantly…
If you ever meet problem when you connect your android with your pc via usb cable and find that your android is charging but could not recognize or there isn’t that options of “USB connection” then just disconnect your android, power off it, remove battery, connect it without battery with your pc through usb, let it have some time to recognize your android or hear that voice of “usb connection” you were just missing…after that, insert battery and switch on your android…you are done!!!
Sometimes removing both sim cards and battery and then re-inserting them after a couple of seconds also works.
Try with different USB Cable
Try in different USB Port
Try in different PC
Sometimes windows XP works when windows 7 fails!!!
Use usbdeview to remove all the usb devices and then add your device
Find proper driver of your device:-
https://drive.google.com/folderview?id=0B511A2txfpAPbmwtQXZqbnVlT1U&usp=sharing
panasonic p81 soft bricked
SP flash tool detected my P81 mobile
but i need rom ROM files to flash
please any one give me rom file to flash Panasonic P81 with SP flash tool
problem solved?
I also had similar problem & solved it. Tell me if the problem is no solved.
damn i don't know what the hell is going on inside my computer but i am not able to get those drivers or i don't know what's the problem. please help me where to get drivers for my panasonic p81 mobile. it is softbricked and i want to install stock rom and i have that cpb files but that ygdp tool isn't working i am in total chaos.
help me please
kartik.krish said:
Yo! I had bricked it too and that too by Xhalomulti window cuz app window is sh!t..... be cool .there is stock rom available at www.xdafirmware.com....google it....also You will recieve a .zip... extract to get .cpb file and use YGDP (assembly:: if ask for password at ygdp type 369)......tap config select cpb. Wait ...connect usb and click start........ok tutorial on Internet.... IMPORTANT THING:: YOU'LL NEED MTK VCOM DRIVER PR ELSE IT WON'T WORK.
Sent from my Panasonic P81 using XDA Labs
Click to expand...
Click to collapse
Thanks so much mate! I fixed with the help of friends at XDA. Which ROM performs best on P81 which runs L or M? I am still on stock and need to upgrade. Do you have suggestions?
kartik.krish said:
Thanks so much mate! I fixed with the help of friends at XDA. Which ROM performs best on P81 which runs L or M? I am still on stock and need to upgrade. Do you have suggestions?
Click to expand...
Click to collapse
Brother I am tired of finding any rom other than stock.on internet there is miui 6 but most people complained it damaged their devices....no cyanogen OS,Color os ,Aokp,Ressurection remix,paranoid nothing........ok i found a phone named Doogee Dagger DG550 having same spects but better ui than playmore and that recently got kitkat too. Im thinking of trying it..if it fails i've
Panasonic original (ok modded a bit) firmware i can flash from ygdp tool..... actually Panasonic P81 is nothing but clone of coolpad 7320 with cool show replaced by playmore and the gesture is new....same multiwindow and the music cafe is nothing but coolpad music renamed....literally im using 7320 rom with build. prop changed so on apps it shows im using p81........Ok if you find rom please post link..... Ps ive tried roms on www.needrom.com but is hopeless.
Sent from my Panasonic P81 using XDA Labs
---------- Post added at 04:39 AM ---------- Previous post was at 04:34 AM ----------
kartik.krish said:
Thanks so much mate! I fixed with the help of friends at XDA. Which ROM performs best on P81 which runs L or M? I am still on stock and need to upgrade. Do you have suggestions?
Click to expand...
Click to collapse
In my opinion MIUI is best because it has a self large community like xda and launch updates per month so many that you will fed up installing them.....if you download and install one update you will be amazed that it will say 3 more system updates pending......and if you complain a bug next month it got fixed.....only thing is to find one...
PS don't download the miui 6 for p81..complained by many p81 user that it hard bricked the device.
And that miui is not official i.e. some developer made his own one and DO not tested that it works or not......
Sent from my Panasonic P81 using XDA Labs
Sir,My Panasonic eluga s is soft bricked, Not starting by pressing any key..it only Starts when connected to PC or charging.. That too in Fastboot mode.. While installing stock ROM using YGDP tool,I am not able to get my mobile in download mode..pls guide..
my panasonic p81 is hard brick,it is not detecting in pc by vcom and other drivers even not booting or charging,please help me devs.
I am connecting my p81 with my sound system but now i cannot hear the voice over a call properly plzz help me out