Hi all
followed this procedure http://forum.xda-developers.com/showthread.php?t=1074979 to root my XOOM WiFi Only MZ604 and now after what appeared to be a successful root on reboot the device is stuck at the Motorola Boot Logo.
Help please.
*update*
Was also following this guide http://forum.xda-developers.com/showthread.php?p=29733454, and out of interest I decided to continue on from Part 3 given I was stuck at the red M. So after applying the EOS flash and GApps, my XOOM now loads up no problem but I am just a bit confused as to what exactly happened.
This is the steps I took to get where I am...
1. Unlock boot loader using Part 1 from here http://forum.xda-developers.com/showthread.php?p=29733454
2. ROOT using this guide http://forum.xda-developers.com/showthread.php?t=1078019
3. Install EOS Flash Part 3 from here http://forum.xda-developers.com/showthread.php?p=29733454
I'm guessing now the stock ROM is now toast?
Related
Yesterday I attempted to update my Xoom to the newest EOS nightly. After installing/wiping/rebooting I found myself with the RSD mode 3 problem. Having encountered this before I used ADB to flash a stock boot & CWM recovery. After this I have tried to flash several different roms (EOS 3/ EOS 4 nightly/CyanogenMod nightly) but each time the device gets stuck at the boot logo, not the motorola dual core screen but the actual ROM boot logo. Any ideas what I should do/try next? I'm sure there must be a simple solution to this, I just don't know/can't find it
Hi guys i have a blu studio 5.5 D610a stuck at the boot screen logo i have no CWM recovery installed just custom <3e> recovery i tried installing from zip and the installation aborts even in sideload it aborts when trying to install any help what can i do to get pass boot loop
Try to flash CWM recovery in it this is the only way! and be carefull dont do any wrong step otherwise u will lose your phone ..
Sent from my A2 using Tapatalk 2
Hello everyone
This is my first post, and I am a slight noob, so please bear with me.
I would like to flash my XT910 with a cyanogen mod. I have flashed the device before, to EU jellybean 4.1.2 (952.124.14.XT910.Retail.en.EU).
However, I now cannot get into recovery mode. The Orange motorola start screen comes up, and then a dead android with a red triangle with an exclamation mark comes up. I cannot get further than this.
I have tried flashing a custom recovery using clockwork and TWRP. I have tried ROM manager, BMM, Rom Installer, etc. all to no avail.
Please can you tell me how to fix my recovery partition so i can flash?
Also I have rooted the device using this thread: http://forum.xda-developers.com/showthread.php?t=2298408 , which seems to be successful.
Thank you for any help!
Dev50
Hi guys,
I have a Moto G2 currently and I have rooted it through KingRoot which was successfully done. After that, I had download the APK of Flash Image GUI and I tried to flash a custom recovery. After that, I tried to boot into recovery but it was showing:
hab check failed for recovery
failed to validate recovery image
Boot up failed
However, I can boot my phone up but it takes way way more time than it usually takes. My Bootloader is locked. I seriously dont know what's happened to my phone. Some plz help me. The phone shows the Motorola logo for few minutes and then turns off for a second and then boots up again and then after 5 minutes it boots up properly. I dont know how to unlock bootloader and all as I have just come from a Samsung S3 which was very easy to root and flash a recovery(thru Odin). I wanted to erase the user data in my phone. I tried thru recovery it didnt happen, i tried thru settings and it just tried to boot to recovery but couldnt and showed the above command. Plz help guys as I want a stock recovery or any other recovery so I can flash a custom ROM. I saw many forums and couldnt find a single problem like this so I came here .
Thanks a lot guys I just had to unlock the boot loader and return to stock 5.0.2 via a windowstool. I had bricked my device trying to install CM12.1 Nightly and the windows tool helped me so much u have know idea.
Hello,
I own a Smartfren Andromax C3 a.k.a. Haier AD6B1H with stock ROM (Android Kitkat 4.4.2) and rooted. Recently I'm trying to update my OS to cyanogenmod but there's no official support for my device, so I take a look at how to port recovery as the first step in cyanogenmod, xda university and koushikdutta site.
I follow the steps as told and success make a recovery.img file, but when I reboot to recovery mode it stuck at boot screen. I remove the battery, wait and put it back to the phone then try recovery mode again but the result is the same as before. Then I try normal boot and success boot to home screen and running as usual without problem. So I change the recovery to stock file and success boot into recovery mode.
How to make the custom recovery running just like the stock without stuck at the boot screen?