I have just purchased a holder for my XDA2 which has a mini USB port on it and I want to connect my TomTom GPS receiver RJ11 connector it.
Does anybody have the same problem or a lead which i can use?
Thanks
if the rj11 connector have all the same connections and signal protocol as usb and maybe even a normal usb connector in the other end then you can buy a normal usb to miniUsb converter
The TomTom reciever has a RJ11 connector and i can not seem to find a converter from RJ11 to anything i.e. USB, Mini USB, etc.
Do you know of any places?
Pratik
well rj11 is a phone connector right ?
and you are sure it's even usb compatible signals running in it ?
i mean if it's analog modem data stuff then converting that signal to something which usb can work with would be a pile of work and end up being more expensive then getting a new gps
True.
RJ11 is a phone connector, but the information from the gps reciever is just being passed to the PDA holder which has a Mini USB connector in it, so I don't think any data conversion is necessary.
The RJ11 has 4 wires in it and the Mini USB has 5, maybe i need to open it up and desolder the mini USB and put in a RJ11 female connector, this then brings me down to pin-out etc.
Do you have any information regarding hte pin-outs?
Pratik
you can get a cable with a mini usb in one end and normal usb in the other if you can get a cable with a mini usb in one end and a female usb in the other then you can connect the usb to xda connector cable that way
of cause that way is way too long but it should make it rather possible to connect the xda to the holder then that is unless
the pda holder and miniUSB connector's signaling require the pda to be a usb host which the xda1 and 2 is not able to be
Maybe we are getting the wires crossed.
The following is a link to the holder
http://www.pdamods.com/proddetail.asp?prod=SPKXDA2&cat=75
The XDA2 sits in the holder just fine and charges at the same time, as it has a connector on the holder, the problem is the GPS connector.
I don't understand your responce to the XDA being a host?
Pratik
RJ-11 to Mini USB Adaptor
I have a pocket, USB Modem at home, and it is RJ-11 on one end, and Mini USB on the other.
Have you tried looking into something like this for a solution?
Guys,
Can anyone provide the pinout of the car charger for Diamond ? I mean the connector which goes directly to the mobile. My was broken and I need to solder it again. Only 2 cables (red & black) but 4 pins on the connector. Which one is going where ?
Thanks in advance
I have a i9003 that have removed the USB port and the tracks are broken.
There would be a way to solder a new connector knowing where to solder the wires would have to load and have USB connectivity?
Best regards.
LoBoHEAT said:
I have a i9003 that have removed the USB port and the tracks are broken.
There would be a way to solder a new connector knowing where to solder the wires would have to load and have USB connectivity?
Best regards.
Click to expand...
Click to collapse
better way go to samsung service centre.
help...does anyone have galaxy fit connector micro charger scheme..please upload to me the image.. because my connector broken n must make a jumper
I have changed my defect display and my right coax connector is broken .
What is the function of this connector / cable
There is a second connector could I use this connector
If you broke the PCB Connector, you need to get to a proper repair shop and have it replaced, if it had a cable and you broke that you need to get it and have them make you a new one. But since it's a phone I would guess it's the PCB antenna. Also those are the antennas for the GSM combo module, WiFI/Bluetooth combo, so you will either have reduced or no signal from your operator or you won't be able to connect to WiFi/Bluetooth reliably or at all.