Guys,
Can anyone provide the pinout of the car charger for Diamond ? I mean the connector which goes directly to the mobile. My was broken and I need to solder it again. Only 2 cables (red & black) but 4 pins on the connector. Which one is going where ?
Thanks in advance
Related
Hi there,
I currently have a recently deceased ipaq 3630 with GPS cable, currently hardwired into my car (I just took the plastics off the plug, hard wired it to ground and ignition power and re-boxed it)
Anyways, I also have an Orange M1000 with 2 cradles, and I'm a cheap*ss mofo.... so what I'm basically planning on is:-
get pinouts for ipaq 3630
get pinouts for M1000 (I see they're in a post in this forum)
cut ipaq end off GPS cable and strip
cut usb end off M1000 cradle cable and strip
using multimeter buzz out the pin -> colour on each of the cables
wire together
glue (or duck tape or something) cradle into car
I'm working on the theory that the gps -> ipaq connection is going to have power and tx/rx which will be all I need for the gps, and that the M1000 cradle will have the same for activesync.
Anyone done this or similar, or does anyone think I'm just crazy?
Cheers
Doogie
Answering my own question because noone else did
The cradle I had was for USB not serial and I couldn't manage to get serial over USB option working in tomtom..... I opened the cradle (T6 driver), split the cable to leave the power going where it was but split out the 2 usb cables and I buzzed out some points on the board where there was connectivity to the 8 & 10 pins... little bit of soldering and reassembly and I now have a serial cradle with power that connects to my GPS..... now just need to make it look purty in my car
Guys,
Can anyone provide the pinout of the car charger for Diamond ? I mean the connector which goes directly to the mobile. My was broken and I need to solder it again. Only 2 cables (red & black) but 4 pins on the connector. Which one is going where ?
Thanks in advance
Hi,
here is the answer:
http://forum.xda-developers.com/attachment.php?attachmentid=31649&d=1164664052
XDA-Wiki can help.
Thanks a lot ! ;o)
help...does anyone have galaxy fit connector micro charger scheme..please upload to me the image.. because my connector broken n must make a jumper
Need help in fixing my samsung galaxy tab 2 7.0 charging/usb cable
Here's my situation,
1. I own original cable and soon tossed it away because the cable has got snapped wires and I find it difficult to solder to the pcb board.
2. I bought another cable, but again, it's having charging issues after 4 months or usage. I'm started to think that these type of cable is easily broken. So I wanted to fix the cable myself by open it up and resoldering the snapped wires in order to save money. The 2nd cable I bought has got no pcb board attached inside. Just pins and solderings.
For now, I just want to be able to charge using the original charger and be able to transfer data files using my pc. So I need help to someone to tell me which wire (color) is attached to which pins. 4 different colors, Black, Red, White and Green. Thanks before.
Here's the look of the 2nd cable when I open it up (removed the remaining snapped wires)
Hi all,
I have a Philips AS111 docking station/bluetooth speaker/charger. Worked perfectly for my SGS2, however, since I bought a new phone (Sony Xperia Z1 Compact) I'm experiencing some problems.
I bought an micro usb to magnetic connector adapter to be able to connect my phone to the dock without having to open the flaps all the time. I took it apart and it basicly splits the first and fifth pin of the micro USB connector to the pins in the magnetic connector. Unfortunately I may not link to external images...
Unfortunately, my phone does not charge when using the adapter in combination with the Philips dock. It does when using the original Sony USB charger and the adapter, so the adapter is fine.
I measured the voltage on the two pins, and it's 0V. I even tried to fool the dock by putting a 1.5kOhm resistor over several lines. Only when I put a 1.5kOhm resistor between 5V and the connector housing, the dock responded by turning on Bluetooth. Voltage went crazy, flipping between 0 and 3V, but phone still doesn't charge.
I think the sollution is to fool the dock by putting a certain resistor between certain lines or by shorting certain lines. Does anyone have a clue how to fool the dock to think there is a device connected, so it opens the +5V line?
Thank you very much!
Nobody into usb connection protocols? :crying:
Finally got it working. Eventually I needed to connect two wires together inside the device. One of them being 'CLAS1' and the other was Ground. Both could be found on the connector going to the micro usb plug of the device. Unfortunately I can not post a link to the photo I made of it.
mblox said:
Finally got it working. Eventually I needed to connect two wires together inside the device. One of them being 'CLAS1' and the other was Ground. Both could be found on the connector going to the micro usb plug of the device. Unfortunately I can not post a link to the photo I made of it.
Click to expand...
Click to collapse
Hello!
I've just bought an AS111. Charges perfectly my SGS4 but it doesn't do a thing when I try connecting my SGN3 (the one with the micro-usb 3 connector) to the Philips dock. I know that the micro-usb 3 is backwards compatible but I do believe that the AS111's dock outputs too little power - or something like that, I am no expert.
I was wondering that maybe your experience could be of help to me. What do you think? If so, could you please guide me through the stuff you did to the dock? Thank you!