Man, I must have some serious derpage going on here, but I cannot get CM10 onto my Skyrocket. I don't consider myself a noob -- been doing this for a few years now -- but this one has me stymied.
My phone is fine in CM9.1.0. When I try to load CM10, following TeamChopsticks CM10 Install Guide I start boot looping. I've gone as far as to wipe everything I can think of (wipe data/factory reset, cache, dalvik, format/data, format/system, format/cache all x3) with no joy. When booting, I get Samsung logo, 60 seconds of CM10 spinning boot animation, freeze and then re-boot.
I'm running sk8erwitskil's 6.0.1.5 CWM Touch Recovery.
Heimdall fails with "libusr error: -12" and I've been unable to resolve that on my local PC.
Download mode says:
ODIN MODE
PRODUCT NAME: SGH-I727
CUSTOM BINARY DOWNLOAD: NO
CURRENT BINARY: SAMSUNG OFFICIAL...dunno if that's right, wrong or indifferent.
As such, I appeal to all you people out there much smarter than I. What else should I do? What else can I check? There must be something fundamentaly wrong with the config of my phone as I know there's a lot of folks out there on Skyrockets with CM10. I'd appreciate any and all help.
TIA,
Bob
Redownload the .zip and check md5
Been there -- Done that
UZ7 said:
Redownload the .zip and check md5
Click to expand...
Click to collapse
Oh, yeah, been there -- done that, but thanks. I'm currently downloading the latest nightly. I'll MD5 it and try again just for giggles, but that hasn't helped in the past. I will update this with the results when done.
EDIT: Yup, downloaded latest nightly, GAPPS (10/11) and MD5'ed 'em all. No joy -- same boot loop. Any other suggestions? TIA...
When things start to crap out, I always think that starting over from the beginning is the best solution. Use Odin to go back to stock and get your phone working and then work your way back into JB.
Here be dragons...
artbybart said:
When things start to crap out, I always think that starting over from the beginning is the best solution. Use Odin to go back to stock and get your phone working and then work your way back into JB.
Click to expand...
Click to collapse
Well, then we are definitely entering the NOOB zone. My sense is that "Here be dragons..."
While the procedure seems easy enough -- thanks to k0nane -- I have several questions.
Will I loose root? (I'm assuming that's a given...)
Do I need to be concerned about the /efs directory?
I'm using my Skyrocket on T-Mobile. Will I lose the unlock?
What else do I need to be aware above before jumping off this cliff?
TIA,
Bob
artbybart said:
When things start to crap out, I always think that starting over from the beginning is the best solution. Use Odin to go back to stock and get your phone working and then work your way back into JB.
Click to expand...
Click to collapse
+1 ^^
Or try twrp, or try a cache wipe and/or reset after rom has installed
Posted w/xda app w/ i727R
MY STICKIES
| ROMS | KERNELS | FIRMWARE | RADIOS | HOWTO'S | GUIDES | INFo |
NEWB GUIDES TO: RESTORE TO STOCK | USE ODIN | INSTALL CWM | ROOT |
My skyrocket was doing the exact same thing. After installing the CM9.1 rom, phone went into boot loop with the same symptoms. After about 10 tries to reboot, I had to flash back to the stock ICS. When that got up and runnung I installed CWM, rooted, then installed Dark_pa ROM. Everything has been running nice and smooth since.
Verify the MD5 hash of the ROM zip file on phone before installing, i had similar problems and it turned out that the file was not being copied to phone properly. Some strange issues and MD5 of the file is always different on the phone.
You can either download MD5 checker from Play store or if you have File Manager, it will show MD5 of the file in File Details.
OR
If you have an external SD card, you can try copying the ROM to SD card using SD CARD adapter.
Stock-town, here I come!
vincom said:
Or try twrp, or try a cache wipe and/or reset after rom has installed
Click to expand...
Click to collapse
Yup, did all that -- no joy.
Jayster0966 said:
My skyrocket was doing the exact same thing. After installing the CM9.1 rom, phone went into boot loop with the same symptoms. After about 10 tries to reboot, I had to flash back to the stock ICS. When that got up and runnung I installed CWM, rooted, then installed Dark_pa ROM. Everything has been running nice and smooth since.
Click to expand...
Click to collapse
Cool -- Nice to get some validation. I think I'll be going the "Return to Stock" route next.
sghi777 said:
Verify the MD5 hash of the ROM zip file on phone before installing, i had similar problems and it turned out that the file was not being copied to phone properly.
Click to expand...
Click to collapse
Tru dat. I always MD5 the file when I put it in it's final resting place. To date, I've never had an MD5 check fail.
Thanks for all the good suggestions, folks. I think I'll take the Odin train back to Stock-town now and then try to get back to JB. I've got everything backed up and am ready to take the plunge! I'll get back to y'all with the results...
EDIT: Hallelujah! (* Cue Angellic Music *)
It worked! When back to stock and worked my way back to JB and it went like clockwork (mod) (pun intended).
Thanks for the advice from everyone. (I'll be smacking Thanks buttons).
Special thanks to vincom for all the great NOOB guides / howto's.
I´am like BobSilva but still in Boot Loop
Hi , I read the thread from the top , and I have a lot in common with BobSilva. I´am not so noob also , but I´am still with the Boot Loop in my Skyrocket .
The difference in that I already did the path back to the stock ROM UCFL6 AT&T Skyrocket and tried again about 3 or 5 times ... Wipping cahe , dalvik /resetig / formating system an etc ...
I have the CWM 6.0.1 / ROM Manager / and I was tried with CM 10 Stable and Nightly Dec 07 . I also left the phone in loop for 10 minutes or more , but still in Boot Loop.
Does anyone can give the steps to put this to work ?
Thanks in advance ....
nelsonmc said:
Hi , I read the thread from the top , and I have a lot in common with BobSilva. I´am not so noob also , but I´am still with the Boot Loop in my Skyrocket .
The difference in that I already did the path back to the stock ROM UCFL6 AT&T Skyrocket and tried again about 3 or 5 times ... Wipping cahe , dalvik /resetig / formating system an etc ...
I have the CWM 6.0.1 / ROM Manager / and I was tried with CM 10 Stable and Nightly Dec 07 . I also left the phone in loop for 10 minutes or more , but still in Boot Loop.
Does anyone can give the steps to put this to work ?
Thanks in advance ....
Click to expand...
Click to collapse
Try return to stock first... See what happens.
Sent from my SAMSUNG-SGH-I727 using xda premium
CM 10 Boot LOOP
droidbabyxda said:
Try return to stock first... See what happens.
Sent from my SAMSUNG-SGH-I727 using xda premium
Click to expand...
Click to collapse
I´am I flshed the stock back and I am now at ICS 4.0.4 Baseband I727UCLI3 kernel 3.0.8 Build numeber UCLF6 Working fine
Seeem that the problem is CWM is not "wipping" something properly ...
Do you have any clue ?
Thanks
Try using twrp I've never had problems with it but have with cwm
Sent from my SAMSUNG-SGH-I957 using xda app-developers app
Thanks JD1639 .... CWM was the issue ... I used the TWRP and CM10 Nightly Dec 09 now is working good.
What I did :
1. Using ODIN I Flashed my stock ICS 4.0.4 UCLF06 ( Details in how to do at the thread NOOB Guide )
2. Using ODIN to install the TWRP ( There is a version of TWRP for that also at the Noob Guide )
3. Root with Superoneclick
4. Download the CM10 Nightly Dec 09 and Gapps and tranfer to Sdcard
5. Using TWRP
a. Backup the actual ROM
b. Factory Reset
c. wipe / data / cache / dalvik
d install CM 10
e install Gapps
f. Reeboot
6. Wait for almost 5 minutes the CM10 Logo and then everything was fine ....
Thanks ....
That sounds good but you didn't need to root it
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
nelsonmc said:
Thanks JD1639 .... CWM was the issue ... I used the TWRP and CM10 Nightly Dec 09 now is working good.
What I did :
1. Using ODIN I Flashed my stock ICS 4.0.4 UCLF06 ( Details in how to do at the thread NOOB Guide )
2. Using ODIN to install the TWRP ( There is a version of TWRP for that also at the Noob Guide )
3. Root with Superoneclick
4. Download the CM10 Nightly Dec 09 and Gapps and tranfer to Sdcard
5. Using TWRP
a. Backup the actual ROM
b. Factory Reset
c. wipe / data / cache / dalvik
d install CM 10
e install Gapps
f. Reeboot
6. Wait for almost 5 minutes the CM10 Logo and then everything was fine ....
Thanks ....
Click to expand...
Click to collapse
Root isn't required to flash roms, and I would personally stay away from super one click to root the phone, as our phones are super easy to root, just use the flashable su file from the root sticky, it takes 3sec's and its impossible to muck up or brick the phone
Posted w/xda app w/ i727R
MY STICKIES
| ROMS | KERNELS | FIRMWARE | RADIOS | HOWTO'S | GUIDES | INFo |
NEWB GUIDES TO: RESTORE TO STOCK | USE ODIN | INSTALL CWM | ROOT |
Usually when I get this problem I force it to recovery and reboot from there or I just restore to my last back up
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
SantiagoSolis said:
Usually when I get this problem I force it to recovery and reboot from there or I just restore to my last back up
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
Click to expand...
Click to collapse
Wtf this threads been dead since December why necro
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
mtdew said:
Wtf this threads been dead since December why necro
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
Click to expand...
Click to collapse
Brain damage
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
Go to Recovery then Factory Reset... I hope you have back up.
Sent from my SAMSUNG-SGH-I727 using xda premium
Related
I'm on CyanogenMod7-7.0.3-NS right now but want to go back to stock 2.3.4 as wavesecure is having issues with Cyanogen and can't verify my sim.
Baseband version: I9020XXKD1
Build Number:GRI40
Will this guide work for my Nexus S? http://forum.xda-developers.com/showthread.php?t=1061855
Sorry newbie here, just want to be really really sure as I followed a poor guide somewhere and got stuck up with the google logo and lock on boot, hence was forced to install cyanogen.
---
UPDATED: 7/8/11
Okay..so to close my question. I just followed this and everything went back to stock.
theunlockr.com/2011/01/20/how-to-unroot-the-nexus-s
1. followed the link above.
2. I remain rooted but recovery went back to stock. no more clockwork.
3. after booting, was alerted of a 2.3.4 update..so I updated again.
4. marketplace has been upgraded to the new interface (probably bec of the update)
5. to install screenshot app and fontchanger..I needed to have super user, so I just installed Clockwork (recovery-clockwork-3.0.2.4-) again and installed SU (su-2.3.6.1-ef-signed.zip) via SD card install.
6. so far, everything's good.
If you have some questions, feel free to ask.
Download a stock rom ( unless you made a nandroid backup)
Turn off you phone then start it while holding vol+
Do a factory reset, wipe cache and dalvik cache( found under advanved)
Flash your stock rom
Sent from my Nexus S using XDA App
Emhalwis said:
Download a stock rom ( unless you made a nandroid backup)
Turn off you phone then start it while holding vol+
Do a factory reset, wipe cache and dalvik cache( found under advanved)
Flash your stock rom
Click to expand...
Click to collapse
thanks! I have made a nandroid backup but I think I may have a corrupted boot.img.
Where can I get a stock rom? Is the one from the link I posted good enough?
Emhalwis said:
Download a stock rom ( unless you made a nandroid backup)
Click to expand...
Click to collapse
Is there a way to return to stock while keeping CWM ?
You can stay on stock rom while you are rooted. You can google it. I got my 2.3.4 from ardoid.com
Its a stock rom with added arabic support. Since you dont need arabic. It wont make any difference to you.
Sent from my Nexus S using XDA App
I'm not asking for keeping root, only to revert back to stock while keeping CWM
Clockworkmod will stay on your phone. As far as i know, all your phone recoveries will be done through cwm
Sent from my Nexus S using XDA App
Emhalwis said:
Clockworkmod will stay on your phone. As far as i know, all your phone recoveries will be done through cwm
Sent from my Nexus S using XDA App
Click to expand...
Click to collapse
I read somewhere that flashing a stock ROM will restore the stock boot/recovery. Is it true ?
That i cant answer u. But i can say that i went back and forth between roms. Reverting to stock when needed. CWM stayed on my phone.
Sent from my Nexus S using XDA App
Ok, will have try. Thanks
dude if install stock rom via odin then u will loss cwm bt iheard u cn gt .zip files of stock roms using tht u wont loss cwn
Thats what im trying to say. The only way (i think) to lose cwm is using odin. But you can find zip stock roms. Thats what i did
Sent from my Nexus S using XDA App
Okay..so to close my question. I just followed this and everything went back to stock.
theunlockr.com/2011/01/20/how-to-unroot-the-nexus-s
1. followed the link above.
2. I remain rooted but recovery went back to stock. no more clockwork.
3. after booting, was alerted of a 2.3.4 update..so I updated again.
4. marketplace has been upgraded to the new interface (probably bec of the update)
5. to install screenshot app and fontchanger..I needed to have super user, so I just installed Clockwork (recovery-clockwork-3.0.2.4-) again and installed SU (su-2.3.6.1-ef-signed.zip) via SD card install.
6. so far, everything's good.
If you have some questions, feel free to ask.
Thanks for the clarification !
I removed the ICS build and use ODIN to return back to stock build.
Still having some problem so i did a data reset. It keep getting stuck there and i already done it three times.
Any suggestions?
So you flashed GB stock.tar through Odin? Do you mean factory/data reset in clockwork recovery? Flashing back to stock should take away your root so you would have to flash CWM again, make a nandroid backup, and flash superuser zip again.
What problems where you having before and after the ICS build?
Explain a bit further exactly what you did.
I installed STOCK Tar using ODIN.
It is booting up fine except i keep getting errors like "android.process.acore" has stopped unexpectedly. Most of the android apps is not working, like phone, contacts, calendars, etc.
I try to do a factory reset and it keep stopping halfway and hangs.
Your going to have to flash the kj2 modem. I had the same problem. I saw that the ucalc4 was still there, its on its own partition so it doesn't get changed when you flash stock tar. What I did...
1. Flash cwm in Odin
2. Boot into cwm (do backup)
3. Flash kj2 modem (I did it twice)
4. Reboot
5. Check baseband (should be uckj2)
This made the FC's go away. It seemed to me that the stock tar doesn't like that baseband, I can't explain why though. Didn't make sense to me but I fixed it. Also I found the ICS leak doesn't like stock recovery. Fyi
Sent from my SAMSUNG-SGH-I727 using xda premium
Little bit lost here.
I already flash it twice using ODIN and using the uckj2 build.
jxl92182 said:
Little bit lost here.
I already flash it twice using ODIN and using the uckj2 build.
Click to expand...
Click to collapse
Build is one thing, baseband is different. When you flash stock your build will be uckj2, you say your on it. OK good. Now check your baseband, will probably still be the ICS baseband ucalc4, that is your modem. You need to flash the uckj2 modem in cwm. http://forum.xda-developers.com/showthread.php?p=20157930
Once you flash that your baseband will be uckj2. That should fix your fc's. Did for me. If not, you may need to try something else which I will explain if need be that will clean things up.
Sent from my SAMSUNG-SGH-I727 using xda premium
Already installed the radio twice.
Original Shipped AT&T Skyrocket Radio I727ATTKJ2 and RIL
using CWM and still giving me errors....
Currently my phone is showing this:
Basband
I727UCKJ2
Kernel
2.6.35.11
Build number
GINGERBREAD.UCKJ2
jxl92182 said:
Already installed the radio twice.
Original Shipped AT&T Skyrocket Radio I727ATTKJ2 and RIL
using CWM and still giving me errors....
Currently my phone is showing this:
Basband
I727UCKJ2
Kernel
2.6.35.11
Build number
GINGERBREAD.UCKJ2
Click to expand...
Click to collapse
OK. What you need to do then is clean things up. There are two ways that I use but I prefer #1.
1. Flash darkside superwipe in cwm. Do a battery pull. Go into Odin and flash k0nanes tar.
OR
2. Flash stock recovery. Wipe data/factory reset. Do a battery pull. Go into Odin and flash k0nanes tar.
Then you can cwm, root, flash anything you want.
Sent from my SAMSUNG-SGH-I727 using xda premium
Thanks a lot hcyplr29 and Presbycusis.
I use darkside's flash and then reload stock.
Everything is fine now.
Glad to hear that. I swear by darkside between ROMS.
Sent from my SAMSUNG-SGH-I727 using xda premium
jxl92182 said:
Thanks a lot hcyplr29 and Presbycusis.
I use darkside's flash and then reload stock.
Everything is fine now.
Click to expand...
Click to collapse
Yah....Darkside.Wipe is killer. Glad to hear your back in action. It is confusing at first getting OS version, kernel, and modem all strait. It is a good learning experience.
Sent from my SAMSUNG-SGH-I727 using xda premium
basically those fc's were becuz the partition table needs to be reset after flashing ics to go back to gb. Darkside does this.
hcyplr29 said:
OK. What you need to do then is clean things up. There are two ways that I use but I prefer #1.
1. Flash darkside superwipe in cwm. Do a battery pull. Go into Odin and flash k0nanes tar.
OR
2. Flash stock recovery. Wipe data/factory reset. Do a battery pull. Go into Odin and flash k0nanes tar.
Then you can cwm, root, flash anything you want.
Sent from my SAMSUNG-SGH-I727 using xda premium
Click to expand...
Click to collapse
please help. i installed ics and cwm then went back to gingerbread.
what i did was
-i used SGH-I727-UCKJ2-k0nane.tar to go back to GB
-after installing it i get FC.
-i installed recovery-clockwork-touch-5.8.1.3-hercules.tar
-after installing it i rebooted to CWM by pressing volume up & down buttons and power button.
-now i couldnt seem to navigate cwm 5.8.1.3. the screen keeps on blinking. when i press down it only gets on option #2 which is install zip. and when i press the power button to ok it doesnt do anything.
i wanted to flash darkside so to wipe everthing. but my cwm is not working.
pls help. i really appreciate all your response
thanks
agenthack said:
please help. i installed ics and cwm then went back to gingerbread.
what i did was
-i used SGH-I727-UCKJ2-k0nane.tar to go back to GB
-after installing it i get FC.
-i installed recovery-clockwork-touch-5.8.1.3-hercules.tar
-after installing it i rebooted to CWM by pressing volume up & down buttons and power button.
-now i couldnt seem to navigate cwm 5.8.1.3. the screen keeps on blinking. when i press down it only gets on option #2 which is install zip. and when i press the power button to ok it doesnt do anything.
i wanted to flash darkside so to wipe everthing. but my cwm is not working.
pls help. i really appreciate all your response
thanks
Click to expand...
Click to collapse
That's because it's touch recovery, you don't push any buttons. Lmao. Touch the screen to use it. Haha
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
hahahaha... woooooo.... that's a good one... well i installed a later version of the CWM.. i think it was 5.0.2.6 version.. is that ok to use? now i can use the up and down buttons... omg! now thats what i call D*mb @$$ hahahaha..my bad my bad
agenthack said:
hahahaha... woooooo.... that's a good one... well i installed a later version of the CWM.. i think it was 5.0.2.6 version.. is that ok to use? now i can use the up and down buttons... omg! now thats i call D*mb @$$ hahahaha..
Click to expand...
Click to collapse
I would just go back to 5.8. It's much better for me. Plus it works far better for ics builds. But yeah, you can use your buttons again for that old ass version you got now
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
ok thanks. i already installed back the latest cwm. now its working! just have 1 question. im trying to look for flash option but theres no option thats says flash. i wanna flash DARKSIDE.SUPER.WIPE.zip its on my sd card already.i tried to click on install zip and chose DARKSIDE.SUPER.WIPE.zip but it says process cant be done..can you please teach me how? sorry for my ignorance.
agenthack said:
ok thanks. i already installed back the latest cwm. now its working! just have 1 question. im trying to llok for flash option but it theres no option thats says flash. i wanna flash Flash DARKSIDE.SUPER.WIPE. its on my sd card already.i tried to click on install zip and chose Flash DARKSIDE.SUPER.WIPE but it says process cant be done..can you please teach me how? sorry for my ignorance.
Click to expand...
Click to collapse
install zip from ad card, then choose zip from sd card. Scroll down and click on the zip
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
got it! just did the darkside wipe...pulled the battery out after..then im flashing it now with odin SGH-I727-UCKJ2-k0nane...hope it works now with no FC and i hope i get my signal back...will update you inawhile..
thanks for your help..
agenthack said:
got it! just did the darkside wipe...pulled the battery out after..then im flashing it now with odin SGH-I727-UCKJ2-k0nane...hope it works now with no FC and i hope i get my signal back...will update you inawhile..
thanks for your help..
Click to expand...
Click to collapse
Don't use that tar. Use sammobile
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
Hi, this is my first post ever on XDA so sorry if im doing it wrong or if its in the wrong spot . anyways i am running stock and am on rooted & unlocked vzw gs3 . I downloaded and installed Scotty's Clean Rom 2.5 which was released just last week. I wiped/factory reset/ formatted everything and the rom seems to install fine, but then when i reboot it stays on the sgs3 boot screen forever? I dont know why it is not working. Ive tried about three times. Thanks.
slegger04 said:
Hi, this is my first post ever on XDA so sorry if im doing it wrong or if its in the wrong spot . anyways i am running stock and am on rooted & unlocked vzw gs3 . I downloaded and installed Scotty's Clean Rom 2.5 which was released just last week. I wiped/factory reset/ formatted everything and the rom seems to install fine, but then when i reboot it stays on the sgs3 boot screen forever? I dont know why it is not working. Ive tried about three times. Thanks.
Click to expand...
Click to collapse
I had the same problem with 2.1 and 2.5 on my phone. For some reason, the flash does not work on my phone the first time. both times I had to pull the battery when I got stuck on the boot screen then boot into recovery, re-wipe, fix permissions and reinstall. It always worked for me on the second try.
Good luck.
slegger04 said:
Hi, this is my first post ever on XDA so sorry if im doing it wrong or if its in the wrong spot . anyways i am running stock and am on rooted & unlocked vzw gs3 . I downloaded and installed Scotty's Clean Rom 2.5 which was released just last week. I wiped/factory reset/ formatted everything and the rom seems to install fine, but then when i reboot it stays on the sgs3 boot screen forever? I dont know why it is not working. Ive tried about three times. Thanks.
Click to expand...
Click to collapse
This happened to me once. Try to re-root the phone again then flash it.
Did you do a dalvick cache wipe too? Also were you flashing a kernel with 2.5? Are you coming from stock or a custom rom too? And if you are coming from a custom rom does it use a custom kernel? You should also check the md5 of the rom and verify it didnt get corrupt on download/transfer.
Sent from my SCH-I535 using xda app-developers app
RE
x714x said:
Did you do a dalvick cache wipe too? Also were you flashing a kernel with 2.5? Are you coming from stock or a custom rom too? And if you are coming from a custom rom does it use a custom kernel? You should also check the md5 of the rom and verify it didnt get corrupt on download/transfer.
Sent from my SCH-I535 using xda app-developers app
Click to expand...
Click to collapse
Yes i wiped the dalvick, fixed permissions, formatted just about everything and factory reset, when that did not work I formatted and wiped everything before and after the flash. still no luck. I was not flashing a kernel, (to be honest im not even sure how to do that) and im coming from a stock rooted rom that i got when i first rooted with odin. I checked the md5 and everything matched up too.
How!?
rpuleo said:
This happened to me once. Try to re-root the phone again then flash it.
Click to expand...
Click to collapse
How do you re root? would i have to use odin to flash the rooted rom again?
The process of how you flashed sounds right.
When you say it's stuck forever, how much time did you give the phone to reboot. Sometimes with a new rom, it may take 5 min or longer for reboot to finish. If you haven't already, just walk away for 5-10 min before checking it.
Sent from a SYNERGIZED GalaxySIII
Clean rom wouldn't install for me on my phone... Weird stuff happened on the screen during boot animation and then would vibrate like crazy and go into boot loop... I came to realize that it was the kernel and I flashed lean kernel and it worked perfectly... I think these roms act differently on everyone's phones and sometimes there's no rhyme or reason to why things work for some people and not others... Just my. 02 cents
Sent from my SCH-I535 using xda app-developers app
Hey all , hope u rocking with your tabs.
anyway, I decided to move on and divorce my stock rom forever
I just would like to ask about a few little things before i get starting flashing.
1 - can i flash Panaroid(Cauz it's awesome and very fast software cycle) with the stock CWM?
2 - if i decided to return back to stock ICS, i will have to wipe data then and would that make me vulnerable to the famous brick bug?
3 - how to backup my stock rom just in case?
4 - what's the biggest sacrifices i will make due to this migration?
well, 2 days now and no one answers these questions :S
Well I have Paranoid installed and its perfect. I backed up my stock ICS and I have a backup. That's all.
Sent from my GT-P6800 using xda premium
samomamo said:
Well I have Paranoid installed and its perfect. I backed up my stock ICS and I have a backup. That's all.
Sent from my GT-P6800 using xda premium
Click to expand...
Click to collapse
okay, the question is: did you installed it with the stock cwm?
and should i back it up with stock cwm also?
bassem.mohsen said:
okay, the question is: did you installed it with the stock cwm?
and should i back it up with stock cwm also?
Click to expand...
Click to collapse
No I have TWRP recovery, I backed up with that and installed the PA.
Sent from my GT-P6800 using xda premium
Hi I am newbie as well. Still see and learn from this great helpful website. I would like to share my experience to play around with custom ROM. and so far still safe. These steps are from what I have done although I have not used the wonderful [ROM][JB : 4.1.2][CM10 Hybrid][P6800\P6810\i815] Paranoid Android v2.22 [17/10][WIP], I am still waiting for the nearly perfect of this rom. .
I am still satisfied with [ROM] Singha ROM Version 1.1.1 (SEP 26 2012). http://forum.xda-developers.com/showthread.php?t=1886370
bassem.mohsen said:
Hey all , hope u rocking with your tabs.
anyway, I decided to move on and divorce my stock rom forever
I just would like to ask about a few little things before i get starting flashing.
1 - can i flash Panaroid(Cauz it's awesome and very fast software cycle) with the stock CWM? It is better using CWM instead of Stock recovery. I am using old version Locerra's recovery at this http://forum.xda-developers.com/showthread.php?t=1542897&page=13. Works perfect so far.
2 - if i decided to return back to stock ICS, i will have to wipe data then and would that make me vulnerable to the famous brick bug? if you have downloaded stock ICS thenI would suggest using CWM when you are installing from zip file. So far I did the bellow steps if using CWM :
1) place on internal SD
2) reboot to CWM
3) wipe data/factory reset in CWM
4) wipe cache
5) advanced > wipe dalvik, wipe battery stats
6) install .zip from INTERNAL SD
7) reboot
Another method is using mobile odin or PC Odin to flash with Stock ICS. You can see at this http://forum.xda-developers.com/showthread.php?t=1469635
3 - how to backup my stock rom just in case? You have to install CWM Recoverry. TWRP http://forum.xda-developers.com/showthread.php?t=1809295 or Locerras' recoverry
4 - what's the biggest sacrifices i will make due to this migration? see The OP updated log. It is nearly perfect and there is still bug. But it depends on individual's opinion.
Click to expand...
Click to collapse
oh, thanks very much, cakrabayu.
much appreciate your help.
ok i have another quick question for people who tried PA roms.
did you tried intensive hd games .. does the performance is better?
Hi – I have a stubborn issue with my Blaze 4G not working on CM roms, I would appreciate any help you guys can provide. Below are the details:
I recently bought a T-Mobile Samsung Galaxy S Blaze 4G, and did the following:
- Rooted it using the following guide (it now has ICS)
- SIM Unlocked it using the following guide (now it works on other networks)
- Updated to CWM 6.0.3.8, since JB roms needs it
- Flashed the T769-UVLH5 modem, since CM support it
And now when I flash CM 10 stable or 10.2 nightly it gets stuck in booting and displaying the CM logo animation screen, after few minutes it reboots and does it all over again.
I remember when I upgraded to CM JB on my SGS3 I needed to flash a JB stock rom on it to get the new boot loaders for JB, but I saw no mention of this on this forum. What else am I missing?
Thanks.
TINGEA said:
Hi – I have a stubborn issue with my Blaze 4G not working on CM roms, I would appreciate any help you guys can provide. Below are the details:
I recently bought a T-Mobile Samsung Galaxy S Blaze 4G, and did the following:
-Rooted it using the following guide (it now has ICS)
-SIM Unlocked it using the following guide (now it works on other networks)
-Updated to CWM 6.0.3.8, since JB roms needs it
-Flashed the T769-UVLH5 modem, since CM support it
And now when I flash CM 10 stable or 10.2 nightly it gets stuck in booting and displaying the CM logo animation screen, after few minutes it reboots and does it all over again.
I remember when I upgraded to CM JB on my SGS3 I needed to flash a JB stock rom on it to get the new boot loaders for JB, but I saw no mention of this on this forum. What else am I missing?
Thanks.
Click to expand...
Click to collapse
You wiped data/cache/system? Reinstall it. Anyways use the new 6.0.4.4 recovery.
Sent from my SAMSUNG-SGH-T769 using Tapatalk
Somcom3X said:
You wiped data/cache/system? Reinstall it. Anyways use the new 6.0.4.4 recovery.
Sent from my SAMSUNG-SGH-T769 using Tapatalk
Click to expand...
Click to collapse
Thanks Somcom. I have to admit that I forgot to do the wipes. but even after doing the wipes (data/system/ factory rest/ cach/devalk) and reinstalling the CM nightly, I still have the same issue.
as for recovery, I updated to the latest version using the rom manager, and according to the official site clockworkmod[dot]com[slash]rommanager (can't post links) I have the latest version for Blaze. how do you get the 6.0.4.4 on blaze?
I still feel it's a ICS vs JB bootloaders issue, but not sure how to proceed next.
Thanks!
TINGEA said:
Thanks Somcom. I have to admit that I forgot to do the wipes. but even after doing the wipes (data/system/ factory rest/ cach/devalk) and reinstalling the CM nightly, I still have the same issue.
as for recovery, I updated to the latest version using the rom manager, and according to the official site clockworkmod[dot]com[slash]rommanager (can't post links) I have the latest version for Blaze. how do you get the 6.0.4.4 on blaze?
I still feel it's a ICS vs JB bootloaders issue, but not sure how to proceed next.
Thanks!
Click to expand...
Click to collapse
No boot loaders man. This is before Samsung's complications.
Recovery is here.
http://d-h.st/AFu
Sent from my SAMSUNG-SGH-T769 using Tapatalk
Thanks Somcom3X, but still didn't work. When installing the CM room in recovery 6.0.4.4 I get a bunch of getprop assert failures. This used to work on the previous version (6.0.3.8). Now the Rom won't install.
Also, I'm curious what did you mean by this is before Samsung's complications?
Thanks
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
TINGEA said:
Thanks Somcom3X, but still didn't work. When installing the CM room in recovery 6.0.4.4 I get a bunch of getprop assert failures. This used to work on the previous version (6.0.3.8). Now the Rom won't install.
Also, I'm curious what did you mean by this is before Samsung's complications?
Thanks
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
After 2011 samsung began installing software and counters to try and prevent people from rooting and installing custom firmwares.
knox is an example of this.
These devices don't have any of that complicated security.
You handy with odin? Your recovery is not right. Just to be clear, what is your model number?
If it is T 7 6 9, your good to go to odin. I'd recommend going back to stock, and then install a recovery and you should be good to go.
Somcom3X said:
After 2011 samsung began installing software and counters to try and prevent people from rooting and installing custom firmwares.
knox is an example of this.
These devices don't have any of that complicated security.
You handy with odin? Your recovery is not right. Just to be clear, what is your model number?
If it is T 7 6 9, your good to go to odin. I'd recommend going back to stock, and then install a recovery and you should be good to go.
Click to expand...
Click to collapse
Thanks again, I use the guide here to convert the image into a tar.md5 to flash using odin, but after flashing successfully I still have the same issue when installing the CM zip file in recovery, and yes it is the T-mobile Samsung Galaxy S Blaze 4G T769.
any other possible causes?
BTW - when I was flashing via Odin my upload phone screen was showing that I have a custom rom and the counter was 1.... do I need to fix that?
TINGEA said:
Thanks again, I use the guide here to convert the image into a tar.md5 to flash using odin, but after flashing successfully I still have the same issue when installing the CM zip file in recovery, and yes it is the T-mobile Samsung Galaxy S Blaze 4G T769.
any other possible causes?
Click to expand...
Click to collapse
SOLUTION:
The reason your stock recovery system keeps getting overwritten at Android startup is because of a script that is being run.* All you need to do is either rename this script or simply delete it.
Please keep in mind that if you restore your stock ROM, this script will be restored with it so you will have to rename or delete it again.* Do the following:*
1.
Make sure your device is powered on and running normally,
2.
Make sure you have rooted your device and that you have all of the necessary permissions in order to manipulate system files.*
3.
In the root file system go to \system\etc
4.
Find the file named install-recovery.sh and either rename it or, as I did, delete it.*
That’s all there is to it.*
Please keep in mind that you will need to flash your custom system recovery one more time after modifying the script file.* After that, reboot away and you will always be able to get back into your new system recovery.
Good Luck and Happy Tweaking.
Click to expand...
Click to collapse
Try that.
Found it here http://mark.candleshoreblog.com/201...-factory-stock-roms-at-android-system-reboot/
Sent from my SAMSUNG-SGH-T769 using Tapatalk
Somcom3X said:
Try that.
Found it here http://mark.candleshoreblog.com/201...-factory-stock-roms-at-android-system-reboot/
Sent from my SAMSUNG-SGH-T769 using Tapatalk
Click to expand...
Click to collapse
Thanks Somcom3X - but I'm not sure this is needed for my case. I read the original blog post and my recovery does not get overwritten. I actually rebooted multiple times into CWM recovery and each time it is the same 6.0.4.4.
I also went into the /system/etc folder and there is no install_recovery.sh file.
to clarify, here is where I'm stuck now:
- when I use CWM 6.0.3.8 CM install completes successfully, but then CM will not boot, and will keep on cycling on the boot logo screen.
- when I use CWM 6.0.4.4 I can't start to install CM as it complained that my phone is not t769.
in all cases I'm using CM 10.2 nightly for T769.
Thanks for the help.
You should delete assert lines at the top of the zip's updater-script and it will let you flash it.
Sent from my SAMSUNG-SGH-T769 using Tapatalk
I removed the assert lines from the updater script, and it was able to complete the install process afterwards, however when I booted the new CM 10.0 system it got stuck on the cyanogenmod boot logo. I made sure I do a system/data rest, cleared cash, and cleared devalk.
I do not think it's an issue with my recovery as I'm getting the same result as I did with the official 6.0.3.8.
Something else is going on.
Any ideas?
Thanks.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
TINGEA said:
I removed the assert lines from the updater script, and it was able to complete the install process afterwards, however when I booted the new CM 10.0 system it got stuck on the cyanogenmod boot logo. I made sure I do a system/data rest, cleared cash, and cleared devalk.
I do not think it's an issue with my recovery as I'm getting the same result as I did with the official 6.0.3.8.
Something else is going on.
Any ideas?
Thanks.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
Tar back to stock GB. Upgrade to ICS. Then root and install cwm. Flash away
Sent from my SAMSUNG-SGH-T769 using Tapatalk
Somcom3X said:
You should delete assert lines at the top of the zip's updater-script and it will let you flash it.
Sent from my SAMSUNG-SGH-T769 using Tapatalk
Click to expand...
Click to collapse
Thanks Somcom3X - but this is more trouble than what I wanted to put in - I'll stick with the rooted stock ROM I have. I was hoping the process was a little more straight forward, similar to my SGS3.
thanks for all your help thus far!
Somcom3X said:
Tar back to stock GB. Upgrade to ICS. Then root and install cwm. Flash away
Sent from my SAMSUNG-SGH-T769 using Tapatalk
Click to expand...
Click to collapse
Ok, my rooted ICS stock is acting up (random shutdowns and such), so I need to give this another try and get this phone to CM.
I tared back to stock GB, skipped the upgrade to ICS (was not able to upgrade via the ROM software update option), flashed CWMR (5.0.4.x) via Odin, upgraded to CWMR 6.0.4.5, installed CM 11 nightly, and then wiped data/factory rest and Dalvik .... and ....
it is still stuck on the boot screen....
I seriously would appreciate a silver bullet right now!
TINGEA said:
Ok, my rooted ICS stock is acting up (random shutdowns and such), so I need to give this another try and get this phone to CM.
I tared back to stock GB, skipped the upgrade to ICS (was not able to upgrade via the ROM software update option), flashed CWMR (5.0.4.x) via Odin, upgraded to CWMR 6.0.4.5, installed CM 11 nightly, and then wiped data/factory rest and Dalvik .... and ....
it is still stuck on the boot screen....
I seriously would appreciate a silver bullet right now!
Click to expand...
Click to collapse
Hmm. Go back to stock ics, flash a 10.2 recovery, then flash whatever you desire.
Sent from my SAMSUNG-SGH-T769 using Tapatalk
What is a10.2 recovery? Is it a certain version of CWMR? And do I need to flash it via Odin? Thanks
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
TINGEA said:
What is a10.2 recovery? Is it a certain version of CWMR? And do I need to flash it via Odin? Thanks
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
It would be cwm 6.0.2.7
You can flash the img through a zip or by terminal on the phone.
Odin needs a tar'd recovery img
Sorry been very busy.
Have you tried this?
http://forum.xda-developers.com/showthread.php?t=2577265
Sent from my SAMSUNG-SGH-T769 using Tapatalk
Thanks Somcom3X - I looked all over this forum and the internet, and could not find a link for a 6.0.2.7 CWM for Blaze - I found it for other phones but not Blaze. can you please point me to a link if you happen to know of one. the official site does not have an archived list of previous versions.
as for the provided link, I did follow it through, and downloaded the recovery Tar (it was CWM 5.5.04) but that yielded the same results after installing CM 10 and 10.2 - stuck at boot screen logo. I'm reasonably confident now that it is not a recovery issue, as I flashed half a dozen different versions and none worked with CM 10, 10.2, or 11.... it has to be something else!
Thanks.
TINGEA said:
Thanks Somcom3X - I looked all over this forum and the internet, and could not find a link for a 6.0.2.7 CWM for Blaze - I found it for other phones but not Blaze. can you please point me to a link if you happen to know of one. the official site does not have an archived list of previous versions.
as for the provided link, I did follow it through, and downloaded the recovery Tar (it was CWM 5.5.04) but that yielded the same results after installing CM 10 and 10.2 - stuck at boot screen logo. I'm reasonably confident now that it is not a recovery issue, as I flashed half a dozen different versions and none worked with CM 10, 10.2, or 11.... it has to be something else!
Thanks.
Click to expand...
Click to collapse
I'm very sorry for the delay. Been very very busy.
https://www.dropbox.com/s/awp1zy4u3x34a2v/CWM-cm-10.2-Recovery-t769.zip
That is my personal 10.2 recovery. Works fine for me.
The author is me, but I was too lazy to change the lines.
Sent from my SAMSUNG-SGH-T769 using Tapatalk