GPS Problem Desire S - HTC Desire S

Hi There,
Im running Virtuous Infinity v1.33.0 Alpha3 on my Desire S.
I tried die AGPS patch Google specific no SSL but it didnt work for me.
Is there a way to improve the GPS signal?
Fluut

GPS is weak on DS.

have you tried all methods to install the patch?

roli006 said:
have you tried all methods to install the patch?
Click to expand...
Click to collapse
i only did it with 4ext

Fluut said:
i only did it with 4ext
Click to expand...
Click to collapse
Try using the adb installer for the GPS fix, worked a treat on my ds
sent from the thing I stab with my finger when I get two minutes

Fluut said:
Hi There,
Im running Virtuous Infinity v1.33.0 Alpha3 on my Desire S.
I tried die AGPS patch Google specific no SSL but it didnt work for me.
Is there a way to improve the GPS signal?
Fluut
Click to expand...
Click to collapse
try change your rom and radio.....on fallout with amida kernel the GPS lock in 30 seconds the most.....

jugg1es said:
Try using the adb installer for the GPS fix, worked a treat on my ds
Click to expand...
Click to collapse
As said above. Basically the majority of the gps fix patch consists of putting local ntp servers in gps.conf, and depending on the patch, one option disables the ssl option for the supl server. I had an issue installing the patch on my other phone and just used adb to remount the system partition and copy a gps.conf file doctored with local ntp servers. You could also use the options in the following thread: http://forum.xda-developers.com/showthread.php?t=953630, which worked first go for me

androvoid said:
As said above. Basically the majority of the gps fix patch consists of putting local ntp servers in gps.conf, and depending on the patch, one option disables the ssl option for the supl server. I had an issue installing the patch on my other phone and just used adb to remount the system partition and copy a gps.conf file doctored with local ntp servers. You could also use the options in the following thread: http://forum.xda-developers.com/showthread.php?t=953630, which worked first go for me
Click to expand...
Click to collapse
This one worked for me the best. Locks within 60sec

Related

Android for Kaiser with Wifi [Beta][Package]

UPDATE 08/26/09
http://www.scarlet-arrow.com/index.php?page=08-26-09---wifi-dma
DISCLAIMER
WARNING: This is given to you with the understanding that I nor the developers will be held responsible for any damage done to your phone while using Android.
Thank you for downloading this pre-packaged Android setup.
This is offered for free and I claim no ownership or rights. I am simply making it easier for you. All credit goes to the hard workers of the Android Vogue(Vogue Linux) project and XDA-Developers forums.
All the developers of the Android Project
Reference sites:
http://code.google.com/p/vogue-android/
http://code.google.com/p/vogue-hero/
Click to expand...
Click to collapse
READ ME
http://scarlet-arrow.com
This package is provided by: Natalic
08/26/09
---------------------------------------------------------------
THIS IS A DMA WIFI HERO BUILD:
Thanks goto addisu and dzo for getting a working Wifi module and all the hard working developers who get Android ported to the various devices.
Thanks to JAC for making the base rom (JACHeroski1.6)
This pack was tested and worked before uploading!
Directions:
0) If you have a data.img delete it first!
1) Copy all files from "Required" to the root of your memory card. I recommend at-least a 512mb.
2) Launch haret and click "Run"
2.1) You will need to wait for the data.img (data store) to be created, this takes around 2 minutes. This stores your files.
3) It takes sometime to get to the setup screen. If the screen turns off, just turn it back on. It will come up.
4) Go through the intro of Android (you only do this once)
The first 3 steps get you into Android
The following gets you Wifi (Kaiser/Tilt only)
* In this build, you can now select your WiFi in the setup.
In side Android:
1) Bring the menu up
2) Goto settings
3) Go to Settings -> Wireless Controls then click "Wi-fi" wait until there is a check
4) Select your network under Wi-Fi Settings
6) Make sure you save your "calibration" file and keep a copy of it save so you can just move it to future builds.
House cleaning:
I did not develop any of this kit, I simply put the pieces together and made them available in an easy to use package.
If you need any help please leave a comment in the forum!
To setup APN you must configure it, this can be found on the Android Vogue Wiki( http://code.google.com/p/vogue-android/wikii/HowToInstall )
Click to expand...
Click to collapse
Reserved
This is reserved.
Do we really need another thread for this? Why can't we just get Newbie to clean up his first post in the other thread? Seems kinda redundant...
loserskater said:
Do we really need another thread for this? Why can't we just get Newbie to clean up his first post in the other thread? Seems kinda redundant...
Click to expand...
Click to collapse
Well, the previous one is not for strictly a build, its more for the wikis and stuff. This thread is strictly for downloading a complete package.
cool, I'll bite!
Trying to follow the steps when i type "su"
i get "uid 10027 not allowed to su" , I did a search for this phrase and the only hit i got was the same error, but person asking was ignored.
Any ideas on how to get around this?
I'm running on a Tilt.
Thanks !!
Excellent, any mirror not from rapid or mega?, my network has the storage web filter , a FTP mirror will be great!
Thanks in advance,
natalic said:
This is reserved.
Click to expand...
Click to collapse
So the hero zip file is a rom? and if so can you flash it to a kaiser ?
keep it up...
if its like HTC HERO, it would be nice
Thanks natalic, it works.
Some additional points:
1) Ensure you're getting the file from the rapidshare link. I tried the latest build from the project site (android-1.5-2009-08-04.zip) and I never managed to extract the calibration file
2) There's a hero build here (http://drop.io/calibrationfiles) but I would suggest to get the calibration file out 1st before trying the hero build. It seems that you wont be able to access the terminal easily from Hero builds... (Maybe it's just me)
What works and not in the Android build (non-hero):-
1) Browser works
2) Market works
3) Google Sync works
4) Google maps does not work
loserskater said:
Do we really need another thread for this? Why can't we just get Newbie to clean up his first post in the other thread? Seems kinda redundant...
Click to expand...
Click to collapse
yes it is, android is starting to need a forum all to itself, or you can look at it like this if the android threads are builds from diff "android chefs" then it would be no different than multiple rom threads for diff chefs or diff wm versions.
Heres my working repack. Enjoy
http://www.mediafire.com/?k13tnjton22
Wifi is working great, Tested on an AT&T tilt with no SIM card inserted. Was able to connect to the internet, download from the market, etc.
How do I get SIM to work and get the phone signal?
shadowline said:
Wifi is working great, Tested on an AT&T tilt with no SIM card inserted. Was able to connect to the internet, download from the market, etc.
Click to expand...
Click to collapse
How did you download from market!? It just hangs on "Starting download" for me. Meh!
*Works. Just had to reboot *
TheParadox said:
How did you download from market!? It just hangs on "Starting download" for me. Meh!
*Works. Just had to reboot *
Click to expand...
Click to collapse
Same goes here.
I am now using HERO UI with a calibration file extracted from the standard build. Apps are not being downloaded... Google maps also not working... (Always Force Close)
Paradox: You forgot to mention about rebooting the phone after running getrom.txt as per your instruction in the zip file.
MOUSEY said:
Same goes here.
I am now using HERO UI with a calibration file extracted from the standard build. Apps are not being downloaded... Google maps also not working... (Always Force Close)
Paradox: You forgot to mention about rebooting the phone after running getrom.txt as per your instruction in the zip file.
Click to expand...
Click to collapse
Sorry mate.
MOUSEY said:
Same goes here.
I am now using HERO UI with a calibration file extracted from the standard build. Apps are not being downloaded... Google maps also not working... (Always Force Close)
Paradox: You forgot to mention about rebooting the phone after running getrom.txt as per your instruction in the zip file.
Click to expand...
Click to collapse
I thought the wifi was cooked into the system file? How do you do that?
MOUSEY said:
Same goes here.
I am now using HERO UI with a calibration file extracted from the standard build. Apps are not being downloaded... Google maps also not working... (Always Force Close)
Paradox: You forgot to mention about rebooting the phone after running getrom.txt as per your instruction in the zip file.
Click to expand...
Click to collapse
Is it reasonably responsive on your kaiser? I tried one build of it today, and it was awful. I mean all the features are cool, but no amount of features can replace responsivness...
MOUSEY said:
Same goes here.
I am now using HERO UI with a calibration file extracted from the standard build. Apps are not being downloaded... Google maps also not working... (Always Force Close)
Paradox: You forgot to mention about rebooting the phone after running getrom.txt as per your instruction in the zip file.
Click to expand...
Click to collapse
Can we see any screenshots of this or can you run such a screenshot program on android?
xxbabiboi228xx said:
Can we see any screenshots of this or can you run such a screenshot program on android?
Click to expand...
Click to collapse
The Hero UI works. Its just not that fast. I can vouch for that. I dont know how he has wifi working on it. I could have sworn the driver had to be cooked into the system.img

[KERNEL] 32a kernel with tun (VPN) support

Hello.
First of all, thanks again to TigerTael for making this possible.
Flashing this will make VPN connections possible from your phone.
The config is based on the latest gbo, with a few tweaks and the new kernel module and auto load from init.rc.
So to install just push wlan.ko and tun.ko to /system/lib/modules and flash boot.
You can ofcourse test this kernel by fastbooting into it.
Download link: http://www.megaupload.com/?d=047LXTK0
I have managed to connect to our Cisco VPN concentrator at work using this kernel and http://get-a-robot-vpnc.googlecode.com/files/VPN_Connections_v08.apk.
To get VPN Connections working I had to:
Install Busybox
Create /etc/vpnc
Copy /data/data/org.codeandroid.vpnc_frontend/files/vpnc-script to /etc/vpnc
Run vpnc from /data/data/org.codeandroid.vpnc_frontend/files via terminal
I am pretty sure there's an easier way, however the GUI just didnt work for me.
This is my first ever release to this forum, please dont bite me if it doesnt run on your device for some reason. And you do this on your own risk
Cheers,
Mockillo
i just uploaded it to megaupload.com, there isnt a download limit and speeds are fast
http://www.megaupload.com/?d=7KMWMZLU
NguyenHuu said:
i just uploaded it to megaupload.com, there isnt a download limit and speeds are fast
http://www.megaupload.com/?d=7KMWMZLU
Click to expand...
Click to collapse
Thanks
Added it to the post.
I'm interested in getting vpnc working (reliably) also.
mockillo said:
First of all, thanks again to TigerTael for making this possible.
Flashing this will make VPN connections possible from your phone.
The config is based on the latest gbo, with a few tweaks and the new kernel module and auto load from init.rc.
So to install just push wlan.ko and tun.ko to /system/lib/modules and flash boot.
Click to expand...
Click to collapse
Right.
snip ...
mockillo said:
To get VPN Connections working I had to:
Install Busybox
Create /etc/vpnc
Copy /data/data/org.codeandroid.vpnc_frontend/files/vpnc-script to /etc/vpnc
Run vpnc from /data/data/org.codeandroid.vpnc_frontend/files via terminal
Click to expand...
Click to collapse
Why did you need to install busy box?
Presumably you needed to create an /etc/vpnc/default.conf as well, yes?
mockillo said:
I am pretty sure there's an easier way, however the GUI just didnt work for me.
Click to expand...
Click to collapse
Yes, the GUI seems to make quite a number of assumptions that are plain wrong.
I've built VPN connections from an svn (rev 125) checkout and the original sources for libcrypt, libgpg-error and vpnc. I also built a kernel from the android-msm-2.6.27 git source (with the TT v2 patch, not that it matters, and a config from my Armon_RA 1.2.1 ROM kernel) and then built tun.ko externally so I could include it in the package. So far the module still has the srcversion info so the kernel version strings must match. I've pushed the module to /system/lib/modules so the module loading changes I've made to VPN connections haven't been tested for the case the module isn't present.
VPN connections seems quite fragile and I really don't like the coding style so I'm trying to change that as I go. After making a few changes to VPN connections I am able get the gui side working. But a really odd and annoying thing is that, while I can get it to work over my WiFi, I can't get it to work over my phone network connection. The configurations setup by vpnc are essentially the same, but no go!
Ian

Incubus' Super Eclair 2.1 R5 for Polaris (Wifi + BT)

Hi everyone! I'm here again to give you good news.
I would like to thank Incubus for his generosity and for his support. We would be nowhere if people like him didn't share their knowledge.
I got into some files and updates and I finally stumbled upon a working set of files that will allow you to start Wi-Fi and Bluetooth in our devices. I made it so we can install it without the need of updates. This build I modified is ready to work with Wi-Fi and Bluetooth.
* For your convenience, I've uploaded the new updated build for you to try it out:
Incubus26Jc's Super Eclair Lite 2.1 Release 5:* http://www.mediafire.com/?jzzygmkjyzm
You've got to use with the latest NBH > http://it029000.massey.ac.nz/vogue/files/?C=M;O=D. Please, make sure you have a NBH file released on 07-05-2010.
Don't forget that I only merged all the stuff and it worked like magic.
I really hope it will work for you too.
I'm now installing things via Wi-Fi and sending files to my Polaris using bluetooth!
Please, tell me if it works.
just installed: my old problems are solved, but i find other 2
_WiFi doesn't search networks
_camera doesn't work (error message processocom.android.camera)
performance
How about the speed of this éclair build working on our Polaris?
Comparing Myn's Warm Donut.
It's a bit slower than Myn's.
loscassapalle said:
just installed: my old problems are solved, but i find other 2
_WiFi doesn't search networks
_camera doesn't work (error message processocom.android.camera)
Click to expand...
Click to collapse
any suggest?
loscassapalle said:
any suggest?
Click to expand...
Click to collapse
It's strange. Wifi works for me. The camera won't work because it has not been ported to Eclair yet.
By the way, is there anybody that has tried out my modification with success? Please, send feedback.
Bluetooth File Transfer
How program you use for send/receive files via BT?
To receive you just have to turn BT on and pair the two devices. It will notify you when an incoming file is waiting (you've got to accept it).
To send I use an app that is named Bluetooth OPP Put Lite. Install it, go to ASTRO File Explorer and choose Send from the context menu. You will see a new option to send the file. I used it and it really works!
Thanks for advice!
Well, wifi scanning is not working Wifi turns on but it does not scan. BT works fine.
Thanx
maybe we could try with WiFi scanner, but without connection we can't go to the market (free)...
I used the .nhb of dzo's latest version (2010-05-07), then bt and wifi are working well.
But I found that Incubus' Super Eclair was much slower than Myn's
loscassapalle said:
just installed: my old problems are solved, but i find other 2
_WiFi doesn't search networks
_camera doesn't work (error message processocom.android.camera)
Click to expand...
Click to collapse
Are you using the latests .NBH? it's dated 07/05/2010
SuperJMN said:
Are you using the latests .NBH? it's dated 07/05/2010
Click to expand...
Click to collapse
yes
should i try to do fix and clear cache?
loscassapalle said:
yes
should i try to do fix and clear cache?
Click to expand...
Click to collapse
I think it w'onk work, but try it. For me, it worked at the very fist time. ztitan says it works for him, too.
SuperJMN said:
I think it w'onk work, but try it. For me, it worked at the very fist time. ztitan says it works for him, too.
Click to expand...
Click to collapse
tryed, but is the same...(but with 2€ less in my sim...it always connect to the network)
No network with wifi ok
Hi SuperJMN,
No way for me : I can't see wifi networks
I tested many times but impossible to use wifi !! I can turn on and off but no network...
I install again and boot twice...
Maybe you do something in install I don't in my phone
Thanks agin for your very good work.
Cheers.
SuperJMN said:
Hi everyone! I'm here again to give you good news.
I would like to thank Incubus for his generosity and for his support. We would be nowhere if people like him didn't share their knowledge.
I messed up with some files and updates and I finally stumbled upon a working set of files that will allow you to start Wi-Fi and Bluetooth in our devices. I made it so we can install it without the need of updates. This build I modified is ready to work with Wi-Fi and Bluetooth.
* For your convenience, I've uploaded the new updated build for you to try it out:
Incubus26Jc's Super Eclair Lite 2.1 Release 5:* http://www.mediafire.com/?jzzygmkjyzm
You've got to use with the latest NBH > http://it029000.massey.ac.nz/vogue/files/?C=M;O=D. Please, make sure you have a NBH file released on 07-05-2010.
Don't forget that I only merged all the stuff and it worked like magic.
I really hope it will work for you too.
I'm now installing things via Wi-Fi and sending files to my Polaris using bluetooth!
Please, tell me if it works.
Click to expand...
Click to collapse
strange... doesnt finish the boot on my pola100
it ends on a black screen
tried on nand with latest nbh
SuperJMN said:
It's strange. Wifi works for me.
Click to expand...
Click to collapse
Could the radio rom be the issue? Which one do you use and which ones others? Lets compare?
Did you combine Kaiser wifi update for eclair and wlan.ko from dzo? That combination worked for me few days ago, and what was interesting that without dzo's wlan.ko wifi coud be enabled, but no scan.
idreadful said:
Could the radio rom be the issue?
Click to expand...
Click to collapse
1.59.46.12. Wifi enables, but does not scan for networks.

No root fix for WiFi and APN - easy SimpleMobile APN Fix

This post is to address how to fix two major issues on the G2X without rooting or flashing . . .
A. How to fix the APN issue which causes the default APN to jump back to T-Mobile . . . after setting up a custom APN such as Simple Mobile . . .
B. How to get the DNS to work on WiFi so that you do not need to restart the phone or switch airplane mode on and off to get it to work.
For the brief time that I had the T-Mobile G2X I notices a couple of issues that were annoying as heck. Loved the phone, but hated that LG was too slow to fix these issues, so I came up with my own fixes / workarounds. I hope that this helps out the community.
A. To fix the APN issue:
Note: Make sure you follow all of the steps exactly / correctly or else it will not work.
1. Simply download APN Manager from the Market.
2. Make a backup of your configuration using APN manager
3. Delete all of the APNs on your phone using APN manager including the T-Mobile APN. (If you ever need it again you can restore it from your backup. You did make a backup right?)
4. Configure your new one and only SimpleMobile APN and set it as the
default
5. Enjoy your Fixed G2X phone
B. To fix the WiFi DNS Issue:
Note: Make sure you follow all of the steps exactly / correctly or else it will not work.
1. Simply Download DNS Setting by Daingo from the Market
2. Run the app
3. Enter the following settings:
I.P. Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Gateway I.P: 0.0.0.0
Primary DNS server: 8.8.8.8
Secondary DNS Server: 8.8.4.4
4. Save and exit
5. Enjoy your Fixed G2X phone
Notes: 8.8.8.8 and 8.8.4.4 are the I.P. Addresses for Google DNS servers, I am told that these DNS servers are blocked by T-Mobile / SimpleMobile, but they will work over WiFi with no problems and the DNS Setting app will only apply it to your WiFi settings, but if you decide to use a different app then keep that in mind.
Also, you may need to set your gateway address to your WiFi routers address, but generally if you set an address as 0.0.0.0 it will default to DHCP (or automatically assign)
This worked for me, and I certainly hope it works for you. I hope I saved many people many headaches.
Now if someone could only figure out how to calibrate the accelerometer.
The infamous developers project is up at http://www.infamousdevelopers.com
Sent from my SGH-T989 using Tapatalk 2
wifi not working
ny time i flash an ICS or JB rom on my g2x the wifi stop working but resumes and work fine when i flash GB. My baseband is March 2012. Any help guys?
mariowinax said:
ny time i flash an ICS or JB rom on my g2x the wifi stop working but resumes and work fine when i flash GB. My baseband is March 2012. Any help guys?
Click to expand...
Click to collapse
I haven't seen this issue, but typically if it won't connect a hard reboot (vol+ and power simultaneously until the set reboots) fixes it.
-- The noob says:
A bootloop is android trying to rationalize pi.
Just did that,but no positive. Its displays ( TURNING ON WIFI........eventually when it ON) it doesnt find any available wifi connections respective to yet available wifi spots......
mariowinax said:
Just did that,but no positive. Its displays ( TURNING ON WIFI........eventually when it ON) it doesnt find any available wifi connections respective to yet available wifi spots......
Click to expand...
Click to collapse
The only other thing I can suggest is to use cleanup batch or nullifier and reinstall. Can't guarantee that it would fix the issue though.
-- The noob says:
A bootloop is android trying to rationalize pi.
Think G2x Scrubber as the same as the batch and e nullifier. Because I always used g2x scrubber to wipe my phone before even installing a custom rom so I don't believe is a problem emanating from there. Anyway thanks for ur consistent aid u giving me,just it doesn't solve ma problem fella.
mariowinax said:
Think G2x Scrubber as the same as the batch and e nullifier. Because I always used g2x scrubber to wipe my phone before even installing a custom rom so I don't believe is a problem emanating from there. Anyway thanks for ur consistent aid u giving me,just it doesn't solve ma problem fella.
Click to expand...
Click to collapse
Scrubber is not the same as batch, which is not the same as nullifier. Batch is my favorite because it removes and reconstructs all partitions.
-- The noob says:
A bootloop is android trying to rationalize pi.
Ok let me try my hands on,can u help me with the link of the nullifier u talking about?
mariowinax said:
Ok let me try my hands on,can u help me with the link of the nullifier u talking about?
Click to expand...
Click to collapse
[email protected] http://forum.xda-developers.com/showthread.php?t=1854850
Cleanup [email protected] http://forum.xda-developers.com/showthread.php?t=1590523
-- The noob says:
A bootloop is android trying to rationalize pi.
Did all with the aid of the soft from the above links. But the wifi still not working. Am using ics Hellfire v1.9, am asking is there any ics good kernel I can flash to aid it working that you are familiar with?
mariowinax said:
Did all with the aid of the soft from the above links. But the wifi still not working. Am using ics Hellfire v1.9, am asking is there any ics good kernel I can flash to aid it working that you are familiar with?
Click to expand...
Click to collapse
Faux 0.14 beta AFAIK. But look in the kernel threads.
Edit: did you do fresh install after the wipe tools or restore from nandroid?
-- The noob says:
Everyone searches, but few have mastered the art of search. Google makes money because of the people of the first kind!
Yes I did, after it I restore from nandroid. But no solution, with the kernel can u give a link to e thread?
Dude...mansa has been babying you this entire thread. Showering you in helpful information while providing links that could be easily found with a quick search. Look through the stickies and find the thread with all the roms and kernels for our device and stop begging for links. Its annoying.
/rant.
-custom sig.
mariowinax said:
Yes I did, after it I restore from nandroid. But no solution, with the kernel can u give a link to e thread?
Click to expand...
Click to collapse
Your restore from nandroid is likely restoring your problem. Try a fresh install. Most folks here seem to like CM7.
Sent from my LG-P999 using xda app-developers app

[Fix] Wifi Fix for ivanich's CyanogenMod

hi,
well, as you know there is problem with CyanogenMod(and some other aosp roms) wifi in some countries and the problem is due to wifi_country_code value inside global database.
so after reading HTCZ715E amazing guide i made this flashable zip for those who still have problem with wifi in ivanich's CyanogenMod.
Installation
flash it via recovery(no need to wipe)
Credits:
@ivanich for his awesome rom
@HTCZ715E for WiFi Country Problem Solving guide
Thank you
I'm going to experience
@jinxul if it's only related to the record in the global table of settings storage database, I thought, wouldn't it be easier to use an init.d script with an addon.d script?
For example:
Code:
#!/system/bin/sh
# Set wifi country code
sqlite3 /data/data/com.android.providers.settings/databases/settings.db "update global set value=nz where name='wifi_country_code';"
hinxnz said:
@jinxul if it's only related to the record in the global table of settings storage database, I thought, wouldn't it be easier to use an init.d script with an addon.d script?
For example:
Code:
#!/system/bin/sh
# Set wifi country code
sqlite3 /data/data/com.android.providers.settings/databases/settings.db "update global set value=nz where name='wifi_country_code';"
Click to expand...
Click to collapse
the main problem is in the telephony-common.jar. every time that wifi turns on framework will rewrite the record on its own... so framework has to be patched(and all that will do is to stop rewriting wifi_country_code on every time wifi turns on).
i also put an script in the zip(similar to this) to change the value back to null but that's just for those who don't want to wipe their data(cause its wont work if there is already a value for wifi_country_code)
so init.d wont do anything as long as framework isnt patched.
jinxul said:
the main problem is in the telephony-common.jar. every time that wifi turns on framework will rewrite the record on its own... so framework has to be patched(and all that will do is to stop rewriting wifi_country_code on every time wifi turns on).
i also put an script in the zip(similar to this) to change the value back to null but that's just for those who don't want to wipe their data(cause its wont work if there is already a value for wifi_country_code)
so init.d wont do anything as long as framework isnt patched.
Click to expand...
Click to collapse
I thought that but when I changed mine to 'us' and toggled wifi on and off a few times and connected to network it didn't revert back for me. I tried 'uk' too but couldn't find any networks when turning wifi on.
hinxnz said:
I thought that but when I changed mine to 'us' and toggled wifi on and off a few times and connected to network it didn't revert back for me. I tried 'uk' too but couldn't find any networks when turning wifi on.
Click to expand...
Click to collapse
reboot is required when you change it manually.. system wont just read it like that unless you tell it to do so, and you cant do that with sqlite3. you need an app/service with WRITE_SETTINGS permission (android.permission.WRITE_SETTINGS).
Let me chime in:
Similar Wi-Fi issues have been persistent across my previous two devices running Android 5+. Setting the Wireless channel of your network to 11 or below (U.S. standard) fixed it. If you don't live in a too dense area - eg. have free uninterfered channels in that scale - then I suggest using those. EU channels (12,13) break far too often due to this specific issue which seems either upstream or hardware-specific. To your information, the three (with this) tested devices all have BCM4329 Wireless modems.
If anyone tries this instead, let me know if it worked here as well.
I would really appreciate if you release Wifi Fix for ivanich's CyanogenMod CM11
this4you said:
I would really appreciate if you release Wifi Fix for ivanich's CyanogenMod CM11
Click to expand...
Click to collapse
as i said in OP i dont have cm11 so i need telephony-common.jar for it. find it (system/framework/telephony-common.jar) and give it to me.
CARBON-KK-UNOFFICIAL-KERNEL-3.4-20141123-1107-pyramid
and again Hi
here you go telephony-common.jar taken from Carbon KK ROM
jinxul said:
as i said in OP i dont have cm11 so i need telephony-common.jar for it. find it (system/framework/telephony-common.jar) and give it to me.
Click to expand...
Click to collapse
there I found it as you directed me and Just Uploaded or should I say posted here for you to get it patched
However it is to say that once I tried the Guide to patch the file but it did not work at all and I faced FC at phone state
actually I could not find the line mentioned in the guide to edit that ...
by the way I`M proud of you
this4you said:
and again Hi
here you go telephony-common.jar taken from Carbon KK ROM
Click to expand...
Click to collapse
try this and let me know the result.
jinxul said:
try this and let me know the result.
Click to expand...
Click to collapse
Thank you ill try it now
in a minute ...
---------- Post added at 08:22 AM ---------- Previous post was at 08:05 AM ----------
jinxul said:
try this and let me know the result.
Click to expand...
Click to collapse
Thank yooooooooooooooooooou It worked !!:good:
I wounder is it possible to put the patched telephony-common.jar inside the Zipped ROM and replaced the old one ?
it may sound rude but as the last request can I upload the vanich's CyanogenMod`s telephony-common.jar ?
this4you said:
Thank you ill try it now
in a minute ...
---------- Post added at 08:22 AM ---------- Previous post was at 08:05 AM ----------
Thank yooooooooooooooooooou It worked !!:good:
I wounder is it possible to put the patched telephony-common.jar inside the Zipped ROM and replaced the old one ?
it may sound rude but as the last request can I upload the vanich's CyanogenMod`s telephony-common.jar ?
Click to expand...
Click to collapse
unzip the rom, replaced it then zip it. it should do the job.
sure.. which one is it?(cm11 or 12)
jinxul said:
unzip the rom, replaced it then zip it. it should do the job.
sure.. which one is it?(cm11 or 12)
Click to expand...
Click to collapse
up to here I was to use viper`s ROM cause of KK`S wifi issues but here you wiped out the nightmare , and I must give you a big thanks...:good:
and again cm-11-20150607-UNOFFICIAL-pyramid ...
but i have to download it first and then upload it here
this4you said:
up to here I was to use viper`s ROM cause of KK`S wifi issues but here you wiped out the nightmare , and I must give you a big thanks...:good:
and again cm-11-20150607-UNOFFICIAL-pyramid ...
but i have to download it first and then upload it here
Click to expand...
Click to collapse
here you go the telephony-common.jar of cm-11-20150607-UNOFFICIAL-pyramid
this4you said:
here you go the telephony-common.jar of cm-11-20150607-UNOFFICIAL-pyramid
Click to expand...
Click to collapse
OP updated to include cm11 patched file.
jinxul said:
OP updated to include cm11 patched file.
Click to expand...
Click to collapse
thank you very much
Great work
After months of searching for a solution
Wi-Fi now works nicely
Without any problems
Thanks
Hi
Please for cm12.1 (06/29) ivanich
Thanks

Categories

Resources