Sorry for being a BAD LUCK NOOOOB... I hav tried flashig roms in mobiles of my frnds and always succeeded... 1st time i tried it on my tab but failed... installed cmw.... backed up evrythng... but unable to wipe data.... its showing unable to mount data.... tried restoring but same error
Stuck wid CWM... now i was thnkng if i can try using odin... i downloaded firmware from sammobile.com
But i thot it wud b better to ask sm1 bfr i do it....
SHUD I ???
PLZ HELP ME
Why did u install cwm in the first place? To install CM10? If so, just flash CM10 anf see what happens.
If not successful, then flash the official firmware downloaded from sammobile.com using Odin and root and install cwm again following the procedures explained in the development section.
Sent from my GT-P6200 using xda app-developers app
i thnk i soft bricked it....
pins2u said:
Why did u install cwm in the first place? To install CM10? If so, just flash CM10 anf see what happens.
If not successful, then flash the official firmware downloaded from sammobile.com using Odin and root and install cwm again following the procedures explained in the development section.
Sent from my GT-P6200 using xda app-developers app
Click to expand...
Click to collapse
Dont want cm10 anymore... Just want my tab to bee BACK ALIVE :fingers-crossed::fingers-crossed::fingers-crossed:
Tried ODIN with official firmware downloaded from sammobile.com. Evrythng went fine. ODIN showed PASS also but jus like before still stuck at the boot logo... I got a pit file with ODIN from sammobiles named P6200.pit. But the firmware i got from sammobile was single .tar.md5 file. And before trying ODIN i read some 10 post and most of it tld not to use PIT wen using single file and to flash it in PDA slot. :fingers-crossed: So i dint use the pit. Only PDA... Did i do smthn wrng??
I have the stock recovery now and still can get into download mode... which makes me belive that i still have hope...
I have downloaded HONEYCOMB stock firmware and was planning to try it. coz i read in a post dat some kernel issue in new firmware is causing bricking in samsung devices.. dont knw if it affects my tab... hope u can help me out
http://forum.xda-developers.com/showthread.php?t=1756242
Recently i read from some post abt using PIT to recover soft bricked devices...
( http://forum.xda-developers.com/showthread.php?t=1667886 )
Since i dint purely understand it, i din try it yet.... Hope u can help me...
AND THANK YOU SO MUCH FOR REPLYING TO MY POST
What is the exact model name of your galaxy tab? There are a few variants of p6200.
I didnt use any pit file when I upgraded my tab from honeycomb to ics and had no issue at all.
Or, try to use firmware emergency recovery tool via Kies. Check out this link from page 7: http://www.sammobile.com/wp-content/uploads/2012/01/KIES-FAQ-update-your-phone.pdf
Sent from my GT-P6200 using xda app-developers app
I m Happy now
Thank you sir. My tab is back to life. I read about an emmc bricking. According to that some part of my internal memory in corrupted. So I had to re partition my internal memory. So, I used a custom PIT file. Now all is well.
maverix13 said:
Thank you sir. My tab is back to life. I read about an emmc bricking. According to that some part of my internal memory in corrupted. So I had to re partition my internal memory. So, I used a custom PIT file. Now all is well.
Click to expand...
Click to collapse
Oh, that was the case.. glad to hear that you solved your problem, sorry for not being a help after all.
Related
Hi,
Please help me.
I tried to install CWM in my galaxy ace using "Odin".
I followed correct steps and odin showed "pass" at last.
but now my phone is not booting.
It will load upto "GALAXY Ace GT-S5830....." scree and nothing is happening after that.
I am not able to boot into recovery also now.
How I can recover my phone back?
Please help me.
Flash everything back to stock with Odin. You should make sure repartition is checked before flashing. When you try to flash cwm through Odin, redownload the files and try again.
Sent from my SGH-T959 using XDA
brnbock said:
Flash everything back to stock with Odin. You should make sure repartition is checked before flashing. When you try to flash cwm through Odin, redownload the files and try again.
Sent from my SGH-T959 using XDA
Click to expand...
Click to collapse
Thanks for replying, but sorry to ask you one more doubt (may be too n00b qn.)
what do you mean by "flash everything"?
where I can get all those files for Ace?
Sorry took soo long to reply, was at work. Can you post a link to the method you used to flash cwm? Just want to make sure I point you to the correct firmware.
I have used the method at
acetips.wordpress.com/2011/10/01/install-cwm-ace-froyo
As it didn't worked, I used some other "ops" file, which brick my phone.
Can I use any samsung upgrade method ( as I have done earlier in my sonyericsson w8 using SEUS) ?
Or how can I fully flash and make it alive?
Try this...!
Hey no phone dies so easily, so, follow the process mentioned in the given link:
http://forum.xda-developers.com/showthread.php?t=1034145
You know how to use odin get you ops file and further download the stock rom on
http://www.sammobile.com/firmware/
thanks friends.
But now I am not able to get into the recovery mode. will it get fixed after flashing the latest firmware?
What is the really working method to get CWM recovery for ACE?
It should work again if u flashed the stock because the stock recovery is included in the stock rom =)
please help me.
my phone is still not turning on, even after flashing stock firmware using odin.
How can i get it back?
my ace is now alive
Thank god!!! at last, my phone is alive.
Now dear friends, do u know any guaranteed to work -cwm flashing methods for ace?
Since you have flashed stock, are you able to get into stock recovery?
Sent from my SGH-T959 using XDA
brnbock said:
Since you have flashed stock, are you able to get into stock recovery?
Sent from my SGH-T959 using XDA
Click to expand...
Click to collapse
Yes, now I am able to get into stock recovery by booting up holding HOME+POWER buttons.
Before CWM, ROOT ur phone...!
eljomon said:
Thank god!!! at last, my phone is alive.
Now dear friends, do u know any guaranteed to work -cwm flashing methods for ace?
Click to expand...
Click to collapse
Before you flash CWM Recovery, you need to ROOT ur phone, download upd_1.zip file from the link that I provided in the previous post and flash it from Stock recovery.
bipinbedi said:
Before you flash CWM Recovery, you need to ROOT ur phone, download upd_1.zip file from the link that I provided in the previous post and flash it from Stock recovery.
Click to expand...
Click to collapse
I agree. Though not totally necessary, it does help. Also enable adb.
Sent from my SGH-T959 using XDA
Yes this is strange ... i was working on REMICS v4 and it was working fine till yesterday but then everything(apps,explorer,theme etc) started crashing so i decided to downgrade to gingerbread.
I tried flashing XXKPE & XXKPQ but both of them keeps rebooting after installation and no User Interface ever appear.
I also tried to install the latest REMICS but it is not working too. What should i do .. its as if the old REMICS file cannot be altered and thus are not allowing any other ROM to work on my device :/ . I can't format the internal sd too
I know its abstract but can any one help ??
alphasahil said:
Yes this is strange ... i was working on REMICS v4 and it was working fine till yesterday but then everything(apps,explorer,theme etc) started crashing so i decided to downgrade to gingerbread.
I tried flashing XXKPE & XXKPQ but both of them keeps rebooting after installation and no User Interface ever appear.
I also tried to install the latest REMICS but it is not working too. What should i do .. its as if the old REMICS file cannot be altered and thus are not allowing any other ROM to work on my device :/ . I can't format the internal sd too
I know its abstract but can any one help ??
Click to expand...
Click to collapse
Clean flash
First download xxkpe firmware package from http://forum.xda-developers.com/showthread.php?t=1004647
Read and follow instructions to flash xxkpe using odin from http://forum.xda-developers.com/showthread.php?t=1133787
Make sure you go thru the complete flashing (pit/pda/modem/etc)
Repeat steps starting from 9 again. This way you'll flash xxkpe twice.
Now you can flash the firmware of your choice. I'll recommend ddlf2 for stock and cm9a11 (or any other based on it).
For ddlf2
download ddlf2 firmware from http://forum.xda-developers.com/showthread.php?t=1741370
Plus download DDLF2_CFROOT-05-07-2012.tar from http://forum.xda-developers.com/showthread.php?t=1331253
Go back to download mode and flash ddlf2 also using odin
Go back to download mode and flash cf-root for ddlf2 again using odin
For CM9A11
download cm9a11 and "google apps" package from http://forum.xda-developers.com/showthread.php?t=1449649
Copy cm9a1a and googleapps zip file to external sd card, as you'll be flashing them using cwm recovery.
go to cwm recovery menu and flash cm9a11 using "install zip file from sd card" option. Make sure you religiously follow all instructions on
http://forum.xda-developers.com/showthread.php?t=1449649
i think ur internal memory may be corrupted try flashing any other rom if that gives any error Ecant mount...then ur internal memory is surely corrupted
Hetalk said:
Clean flash
First download xxkpe firmware package from http://forum.xda-developers.com/showthread.php?t=1004647
Read and follow instructions to flash xxkpe using odin from http://forum.xda-developers.com/showthread.php?t=1133787
Make sure you go thru the complete flashing (pit/pda/modem/etc)
Repeat steps starting from 9 again. This way you'll flash xxkpe twice.
Now you can flash the firmware of your choice. I'll recommend ddlf2 for stock and cm9a11 (or any other based on it).
For ddlf2
download ddlf2 firmware from http://forum.xda-developers.com/showthread.php?t=1741370
Plus download DDLF2_CFROOT-05-07-2012.tar from http://forum.xda-developers.com/showthread.php?t=1331253
Go back to download mode and flash ddlf2 also using odin
Go back to download mode and flash cf-root for ddlf2 again using odin
For CM9A11
download cm9a11 and "google apps" package from http://forum.xda-developers.com/showthread.php?t=1449649
Copy cm9a1a and googleapps zip file to external sd card, as you'll be flashing them using cwm recovery.
go to cwm recovery menu and flash cm9a11 using "install zip file from sd card" option. Make sure you religiously follow all instructions on
http://forum.xda-developers.com/showthread.php?t=1449649
Click to expand...
Click to collapse
Well i tried flashing XXKPE twice n then XXKPQ n i even tried it with the universal kernel .. it didn't work .. you think DDLF2 would be worth a try ??
pratik_s said:
i think ur internal memory may be corrupted try flashing any other rom if that gives any error Ecant mount...then ur internal memory is surely corrupted
Click to expand...
Click to collapse
Well REMICS works .. but everything crash's if i work on it ... n ya i do get the error e: can't mount /data when i try to install a stock ROM of Gingerbread ... but no such error in FROYO or REMICS
Even i had same issue and when i tried to flash only Rom xxkpq, mobile didn't boot. Then I flashed xxkpq along with bootloader, modem files and it worked. I think it's problem with the bootloader.
Sent from my GT-I9003 using xda app-developers app
abhisal said:
Even i had same issue and when i tried to flash only Rom xxkpq, mobile didn't boot. Then I flashed xxkpq along with bootloader, modem files and it worked. I think it's problem with the bootloader.
Sent from my GT-I9003 using xda app-developers app
Click to expand...
Click to collapse
You flashed it with XXKPE bootloader ?? I will give it a try but i guess my internal memory is corrupted
i think ur internal memory is corrupted i have also faced the same problem u can refer my thread if ur getting that problem try the solution posted by ahmedjust http://forum.xda-developers.com/showthread.php?t=1735718 it is a difficult solution to implement but u can try
pratik_s said:
i think ur internal memory is corrupted i have also faced the same problem u can refer my thread if ur getting that problem try the solution posted by ahmedjust http://forum.xda-developers.com/showthread.php?t=1735718 it is a difficult solution to implement but u can try
Click to expand...
Click to collapse
well i tried it already ... but after editing and pushing the fstab files the system doesn't boot and n if i flasg again then the files are gone ...
Infact on rebooting to recovery the original fstab file replaces the new edited one ..
alphasahil said:
well i tried it already ... but after editing and pushing the fstab files the system doesn't boot and n if i flasg again then the files are gone ...
Infact on rebooting to recovery the original fstab file replaces the new edited one ..
Click to expand...
Click to collapse
if ur sl is in warranty rush to your nearest samsung service centre and get ur motherboard replaced for free.
i flashed with xxkpq bootloader. I will send you link as soon as i reach home. give it a try. I flashed stock Rom and then re rooted it.
Sent from my GT-I9003 using xda app-developers app
pratik_s said:
if ur sl is in warranty rush to your nearest samsung service centre and get ur motherboard replaced for free.
Click to expand...
Click to collapse
I wish i was ...
http://forum.xda-developers.com/showthread.php?t=1133787
http://androidadvices.com/root-sams...ingerbread-xxkpq-236-firmware/3/#.UBYIvKDwqAA
Follow exact steps to install this Rom.
Sent from my GT-I9003 using xda app-developers app
abhisal said:
http://forum.xda-developers.com/showthread.php?t=1133787
http://androidadvices.com/root-sams...ingerbread-xxkpq-236-firmware/3/#.UBYIvKDwqAA
Follow exact steps to install this Rom.
Sent from my GT-I9003 using xda app-developers app
Click to expand...
Click to collapse
sorry but i guess you didn't read my initial post. I know how to flash ROMS... I hv flashed many over the past.
I can't flash due to some fault in the internal storage.. any solutions??
Sorry my bad. Actually wanted to give u link which contains stock roms along with bootloader, modem etc.
http://forum.xda-developers.com/showthread.php?t=1004647
I flashed xxkpq from above link. Try this. Hope this works
Sent from my GT-I9003 using xda app-developers app
abhisal said:
Sorry my bad. Actually wanted to give u link which contains stock roms along with bootloader, modem etc.
http://forum.xda-developers.com/showthread.php?t=1004647
I flashed xxkpq from above link. Try this. Hope this works
Sent from my GT-I9003 using xda app-developers app
Click to expand...
Click to collapse
This method only works if your internal card is unreadable but in case it is readable and has bad sectors the above method fails
WHY? It's actually very simple and logical .. when your internal card is unreadable the /dev/mmcblk0 is automatically assigned to external card which if partitioned properly can support a new ROM
But if the internal card has bad sectors than /dev/mmcblk0 is still with internal card and thus you can't install a new ROM on this corrupt card.. Therefore boot.img needs to be altered to map all mount data to mmcblk1 instead of mmcblk0.. it's very lengthy and tiring ... so unless you have a lot of free time and very less money to spend i recommend going to the service center .. :/
hye. can somebody help me. my tab plus having problem after upgrading using kies. it stuck for over an hour and i unplugged usb from the tab. when i turn it on, it appear "firmware upgrade encountered an issue. please select recovery ode in kies & try again" . but when i plug my tab, the kies seem like doesnt recognize the tab. it doesnt connect with my tab. is my tab brick?what can i do to make it function again?please help me.:crying:
Im not really an expert but i'll try..
Can you enter odin mode? If yes, then you can flash your stock HC rom.. but guessing from your problem.. do you know how to use odin? If dont, try to do some research.. so heres my tip..
1. Find your stock HC firmware at www.samfirmware.com
2. Flash the firmware via odin..
3. (From experience) it will boot loop in the samsung animation
4. Dont worry.. enter recovery and do both wipes
5. Your boot will now proceed..
BEFORE I FORGET.. WIPING IS SAFE ON STOCK HC ROM.. DO NOT WIPE FROM STOCK ICS ROM.. I REPEAT DO NOT WIPE FROM STOCK ICS ROM
PEOPLE OUT THERE.. PLEASE CORRECT ME IF IM WRONG..
IM JUST HELPING OUR FRIEND HERE..
Sent from my GT-P6200 using XDA Premium HD app
I have the same issue when i flash my tab with the latest firmware..but then i flash latest cwm odin version..go to cwm recovery..and did factory reset..bravo!!! My tab is alive
Sent from my GT-P6200 using xda premium
theejay0625 said:
Im not really an expert but i'll try..
Can you enter odin mode? If yes, then you can flash your stock HC rom.. but guessing from your problem.. do you know how to use odin? If dont, try to do some research.. so heres my tip..
1. Find your stock HC firmware at www.samfirmware.com
2. Flash the firmware via odin..
3. (From experience) it will boot loop in the samsung animation
4. Dont worry.. enter recovery and do both wipes
5. Your boot will now proceed..
BEFORE I FORGET.. WIPING IS SAFE ON STOCK HC ROM.. DO NOT WIPE FROM STOCK ICS ROM.. I REPEAT DO NOT WIPE FROM STOCK ICS ROM
PEOPLE OUT THERE.. PLEASE CORRECT ME IF IM WRONG..
IM JUST HELPING OUR FRIEND HERE..
Sent from my GT-P6200 using XDA Premium HD app
Click to expand...
Click to collapse
thanks!!i will try this. and i just realize that i posted this in development section. sorry.
arfian said:
I have the same issue when i flash my tab with the latest firmware..but then i flash latest cwm odin version..go to cwm recovery..and did factory reset..bravo!!! My tab is alive
Sent from my GT-P6200 using xda premium
Click to expand...
Click to collapse
i'm downloading the latest firmware right now and try this method after the download is done. i hope my tab will be just like yours. ALIVE!!
edit : its not working. failed flashing with odin. i dunno what happen. is there any other solution. my tab is not rooted and for sure usb debugging also off. maybe flashing with odin failed because usb debugging is off right.
mijul mojas said:
thanks!!i will try this. and i just realize that i posted this in development section. sorry.
Click to expand...
Click to collapse
theejay0625 said:
Im not really an expert but i'll try..
Can you enter odin mode? If yes, then you can flash your stock HC rom.. but guessing from your problem.. do you know how to use odin? If dont, try to do some research.. so heres my tip..
1. Find your stock HC firmware at www.samfirmware.com
2. Flash the firmware via odin..
3. (From experience) it will boot loop in the samsung animation
4. Dont worry.. enter recovery and do both wipes
5. Your boot will now proceed..
BEFORE I FORGET.. WIPING IS SAFE ON STOCK HC ROM.. DO NOT WIPE FROM STOCK ICS ROM.. I REPEAT DO NOT WIPE FROM STOCK ICS ROM
PEOPLE OUT THERE.. PLEASE CORRECT ME IF IM WRONG..
IM JUST HELPING OUR FRIEND HERE..
Sent from my GT-P6200 using XDA Premium HD app
Click to expand...
Click to collapse
its not working. failed flashing with odin. i dunno what happen. is there any other solution. my tab is not rooted and for sure usb debugging also off. maybe flashing with odin failed because usb debugging is off right.
Hello guys, whats up?
i was using cyanogem mod 10.1 but it was no good so i decided to use odin and flash a stock 4.0.4 rom for my p6210, i found it at sam firmware, it flashed ok but it was freezing on samsung so i decided to try again and odin showed me its sucessfull but it is not..
Now the tablet shows me " firmware upgrade encountered an issue, please select recovery mode in kies & try again.
Any help? thanks
Still dont works
Ok now ive found an other odin version 1.83 and used pda>>start and it was perfect but now i receive annother error, i shows me could not mount /system... guys please? i think i need the pit file for the P6210 tablet and i could not find it, where can i find it?
Have u tried to check it out at samfirmware..somewhere out there..
Sent from my GT-P6200 using xda premium
do you wipe data before flash the stock 4.0.4???
If not, flash the CWM recovery and wipe data and flash again the stock firmware.
::good::good::good::good::good::good::good::good:
To downgrade galaxy tab plus p6200 form jb xxmc3 based version to stock ics :-
Installation instructions :
1.First download the stock ics rom based on ur network carrier,,for assistance i am using INDIA network carrier based rom,,For those who r outside form india choose ur country based rom by clicking the link below http://www.sammobile.com/firmwares/1/
2.once u have downloaded the rom succesfully extract it somewhere on pc ..Put ur tab in download mode open "ODIN.exe" choose pda as ".tar.md5" dont use pit file avoid it also dont tick on repartition...and click on start wait for 5min-----Now ur tab is downgrading and it shall boot,,,,Once its done u will see samsung logo ..if u face any problems like force close etc.,go to SETTINGS-PRIVACY-FACTORY RESET...Thats it U have successfully done>>>
IMPORTANT on't wipe data / factory reset by going to recovery it will leads to permanent brick:crying::crying::crying::crying::crying::crying::crying::crying::crying::crying::crying::crying::crying::crying:
If u want to make a repartition ur tab using a pit file downlaod the attachment,,,Be carefull !!!!!!!!!
katarusiva said:
::good::good::good::good::good::good::good::good:
To downgrade galaxy tab plus p6200 form jb xxmc3 based version to stock ics :-
Installation instructions :
1.First download the stock ics rom based on ur network carrier,,for assistance i am using INDIA network carrier based rom,,For those who r outside form india choose ur country based rom by clicking the link below http://www.sammobile.com/firmwares/1/
2.once u have downloaded the rom succesfully extract it somewhere on pc ..Put ur tab in download mode open "ODIN.exe" choose pda as ".tar.md5" dont use pit file avoid it also dont tick on repartition...and click on start wait for 5min-----Now ur tab is downgrading and it shall boot,,,,Once its done u will see samsung logo ..if u face any problems like force close etc.,go to SETTINGS-PRIVACY-FACTORY RESET...Thats it U have successfully done>>>
IMPORTANT on't wipe data / factory reset by going to recovery it will leads to permanent brick:crying::crying::crying::crying::crying::crying::crying::crying::crying::crying::crying::crying::crying::crying:
If u want to make a repartition ur tab using a pit file downlaod the attachment,,,Be carefull !!!!!!!!!
Click to expand...
Click to collapse
i dont see why this is a solution.. you can always downgrade via odin.. solution for what?
Sent from my GT-P6200 using XDA Premium HD app
theejay0625 said:
i dont see why this is a solution.. you can always downgrade via odin.. solution for what?
Sent from my GT-P6200 using XDA Premium HD app
Click to expand...
Click to collapse
I know that we can always downgrade through "ODIN" no need to say that ....But some of the members asked me how to do that ....Thats why i wrote a post....:highfive::highfive::highfive:
i need a solution infact!
theejay0625 said:
i dont see why this is a solution.. you can always downgrade via odin.. solution for what?
Sent from my GT-P6200 using XDA Premium HD app
Click to expand...
Click to collapse
Hi
im new to here
I just wana say that its not that much clear! and i need a solution! because when i do this my p6200 reboots and then samsung logo dont go!
it means i cant see anything more than samsung logo.
please gimme a solution for this. i used odin and several roms but finally i had to flash 4.1.2
what should i do to downgrade from 4.1.2 uncomfotable UI to 4.0.4 speedy and likely one ?
salarse said:
Hi
im new to here
I just wana say that its not that much clear! and i need a solution! because when i do this my p6200 reboots and then samsung logo dont go!
it means i cant see anything more than samsung logo.
please gimme a solution for this. i used odin and several roms but finally i had to flash 4.1.2
what should i do to downgrade from 4.1.2 uncomfotable UI to 4.0.4 speedy and likely one ?
Click to expand...
Click to collapse
When u flash HC.. it will always boot loop.. to fix the boot loop problem.. enter recovery power button + volume up.. the wipe cache and wipe partition.. then the boot loop will be fixed.. then upgrade to ICS or JB whatever you want.. by the way.. dont EVER wipe from a ICS stock recovery.. cause this will brick ur tab.. please remember that.. if u want to wipe from a ICS rom.. install CWM then wipe in the CWM recovery.. JB is faster than ICS
Sent from my GT-P6200 using XDA Premium HD app
I have a P6210. How would I flash from UK 4.1.2 back to HC Using a PIT to repartition?
theejay0625 said:
When u flash HC.. it will always boot loop.. to fix the boot loop problem.. enter recovery power button + volume up.. the wipe cache and wipe partition.. then the boot loop will be fixed.. then upgrade to ICS or JB whatever you want.. by the way.. dont EVER wipe from a ICS stock recovery.. cause this will brick ur tab.. please remember that.. if u want to wipe from a ICS rom.. install CWM then wipe in the CWM recovery.. JB is faster than ICS
Sent from my GT-P6200 using XDA Premium HD app
Click to expand...
Click to collapse
hi sir i am also flash and upgrade my Tab 7 plus from HC to JB
but not done the wipe cach ..so after i flash it with ODIN
it working smooth for some time but it suddenly restart and now stuck at Samsung galay tab plus logo
i tried to go in POWER+VOLUME UP ..RECOVERY MODE ..
But its not coming ..POWER+VOLUME DOWN ...DOWLOAD mode is coming
So i again flash it with ODIN..BUT again its Stuck at Logo
What soution YOu can Give ..Is i have To downgrade it with 4.0.4 ..OFFICIAL Firmware ...
Please Helip
Is there something wrong with the JB? why the downgrade!
Sent from my GT-I9082 using xda app-developers app
aktsa said:
hi sir i am also flash and upgrade my Tab 7 plus from HC to JB
but not done the wipe cach ..so after i flash it with ODIN
it working smooth for some time but it suddenly restart and now stuck at Samsung galay tab plus logo
i tried to go in POWER+VOLUME UP ..RECOVERY MODE ..
But its not coming ..POWER+VOLUME DOWN ...DOWLOAD mode is coming
So i again flash it with ODIN..BUT again its Stuck at Logo
What soution YOu can Give ..Is i have To downgrade it with 4.0.4 ..OFFICIAL Firmware ...
Please Helip
Click to expand...
Click to collapse
Have you tried flashing the CWM? Try flashing the custom recovery.. then try to enter recovery..
Sent from my GT-P6200 using XDA Premium HD app
Oracle1977 said:
Is there something wrong with the JB? why the downgrade!
Sent from my GT-I9082 using xda app-developers app
Click to expand...
Click to collapse
Yes, I would like to know also! I am trying the opposite and trying to upgrade my US version of 4.0.4 to the UK version 4.1.2 which is suppose to work, but I can't seem to get my USB to be recognized when I am in the Download mode - Funny thing, the USB is recognized when directly connecting to my computer (ie MTP) and via Kies, but not in the DL mode or Odin.
But if 4.0.4 is more trouble free than 4.1.2, maybe my problem is a good thing?
Edit: Figured it out - I was in Recovery mode instead of Download mode - oh well, 4.1.2 is a little nicer, with a few more features, not notably faster that I can tell as of yet, but I need to play with it, since all I have done so far is to go through it and make sure things work.
I was hoping for multi-window support and better wifi connectivity, but no joy - maybe better wifi after a few more days?.
Does anyone know if 4.1.2 will allow the tab to support 64gb card? I thought that was one area where 4.1.2 had over 4.0.4