Iv'e flashed every kernel i could find and used all different settings when installing but my phone stays on the HTC logo for about 3-4 minutes before starting up, even when rebooted 2-3 times its still the same iv'e tried wiping and installing rom again without flashing kernel an boot time is about 60 seconds so it must be the kernel messing up my device.anyone else have this problem?
ryanraven said:
Iv'e flashed every kernel i could find and used all different settings when installing but my phone stays on the HTC logo for about 3-4 minutes before starting up, even when rebooted 2-3 times its still the same iv'e tried wiping and installing rom again without flashing kernel an boot time is about 60 seconds so it must be the kernel messing up my device.anyone else have this problem?
Click to expand...
Click to collapse
if i was you i would try do a full wipe and then run an ruu, just to give yourself a fresh install. then place a custom recovery onto the phone again and install your rom of choice. if its still lagging then i dont know what it could be:/
heavy_metal_man said:
if i was you i would try do a full wipe and then run an ruu, just to give yourself a fresh install. then place a custom recovery onto the phone again and install your rom of choice. if its still lagging then i dont know what it could be:/
Click to expand...
Click to collapse
but doesn't RUU lock bootloader etc ?
ryanraven said:
but doesn't RUU lock bootloader etc ?
Click to expand...
Click to collapse
yea it does.as i see you are S-OFF so you do not need to flash the boot.img manually but give it a try to see if it works.if it is not then from recovery do format all partition(except sd card)and flash the rom again.best wishes
ryanraven said:
but doesn't RUU lock bootloader etc ?
Click to expand...
Click to collapse
it does, but since you are s-off you can just reflash the revolutionary/ jupuntobear hboots to have fastboot enabled ect
okay iv'e done all that installed RUU wiped everything etc install rom and installed kernel and still takes the same amount of time to start up so wiped again and left it with the kernel that came with the rom and it starts up much faster not sure why no kernel works properly with this rom. HyperSensation 3.1 CM
ryanraven said:
okay iv'e done all that installed RUU wiped everything etc install rom and installed kernel and still takes the same amount of time to start up so wiped again and left it with the kernel that came with the rom and it starts up much faster not sure why no kernel works properly with this rom. HyperSensation 3.1 CM
Click to expand...
Click to collapse
maybe its just the kernel your trying to flash doesnt like your phone ;P. which kernel is it?
heavy_metal_man said:
maybe its just the kernel your trying to flash doesnt like your phone ;P. which kernel is it?
Click to expand...
Click to collapse
ive tried a few and their all the same
XxXPachaXxX kernel aroma installer v2.53
Pyramid-ICS-XE-010b2-300-aroma
Bricked-3.0-v1.4-ics-maxkhz=1566000-minkhz=192000-maxscroff=486000 << Starts up the same time as ROM Kernel
3.0.40-TAMCORE-00689-gfe1a294
You do realize that different kernels are for either sense or aosp right?
Sent from my Sensation
blahbl4hblah said:
You do realize that different kernels are for either sense or aosp right?
Sent from my Sensation
Click to expand...
Click to collapse
yes but all of these kernels were recomended by other users to use with non sense roms
Related
my phone is rooted running cyanogenmod 9 and whenever i want to install a sense rom it stays at the boot animation ive tried everything i even used the latest t mobile ruu to restore back to stock and it will not boot with the stock rom what can i do to fix this problem??
adame09 said:
my phone is rooted running cyanogenmod 9 and whenever i want to install a sense rom it stays at the boot animation ive tried everything i even used the latest t mobile ruu to restore back to stock and it will not boot with the stock rom what can i do to fix this problem??
Click to expand...
Click to collapse
I have experienced the same problem. Running CMX is fine but phone wont boot if flash sense based rom. Also, I am not able to flash firmware, phone either skip to update or says parsing package then skip. I am only htcdev unlocked and s-on. Really need help please.
adame09 said:
my phone is rooted running cyanogenmod 9 and whenever i want to install a sense rom it stays at the boot animation ive tried everything i even used the latest t mobile ruu to restore back to stock and it will not boot with the stock rom what can i do to fix this problem??
Click to expand...
Click to collapse
I know it sounds silly but I've had a similar problem in the past but it was all because I forgot to format the Partitions, dalvik cache from the recovery menu etc. Maybe try that if you haven't already. Hope it helps
Hi,
I have currently 4.5 CleanRom, and I used TWRP to install it, but I want Jellybean on my phone, can I just use TWRP to install CyanogenMod 10 with it? or do I need another installer of roms like CWM Recovery?
thanks.
yching07 said:
Hi,
I have currently 4.5 CleanRom, and I used TWRP to install it, but I want Jellybean on my phone, can I just use TWRP to install CyanogenMod 10 with it? or do I need another installer of roms like CWM Recovery?
thanks.
Click to expand...
Click to collapse
of course you can, but if you're on a newer Hboot, you will need to boot the rom through fast boot with boot.img
but of course.
dustin4vn said:
of course you can, but if you're on a newer Hboot, you will need to boot the rom through fast boot with boot.img
but of course.
Click to expand...
Click to collapse
I already have TWRP installed and I know how to access it on fastboot, the only reason I asked why is because I have seen some rooms not working properly with CWM Recovery, so I didnt know if there was any problem the other way around with roms like Cyanogen.
Thanks!
your good to go with twrp, i recommend updating to twrp 2.3.1.0
Will the CM nightlies flash normally on the old hboot?
Sent from my Nexus 7 using xda premium
they should but if you have any problems go into bootloader and run this command "fastboot erase cache"
are you using twrp 2.3.1.0?
Bootlooping CM10 on Telstra One XL
Hey guys been trying to work this out for the last 20 hours.
Now i followed the very good guides to put TWRP on the phone that worked fine tried to load cm10 latest nightly rom on kept bootlooping. so decided to give another rom ago.
used viper and it worked fine.
wanted to try and get cm10 working
So i have twrp 2.3.1
And latest cm-10-20121102-NIGHTLY-evita.zip
i wipe system, factory default cache. and the other cache.
go and install the rom all looks good, wipe caches and reboot.. than goes to the cool cm10 logo and loops there for AGES like 30 mins than i power cycled it and tried over.
with no working cm10 there i looked around and followed a guide to fastboot a new boot.img on from out of the cm10 zip.
this looked like it was going to work but still reboot and bootlooping.
can anyone help please.
AnThraXau said:
Hey guys been trying to work this out for the last 20 hours.
Now i followed the very good guides to put TWRP on the phone that worked fine tried to load cm10 latest nightly rom on kept bootlooping. so decided to give another rom ago.
used viper and it worked fine.
wanted to try and get cm10 working
So i have twrp 2.3.1
And latest cm-10-20121102-NIGHTLY-evita.zip
i wipe system, factory default cache. and the other cache.
go and install the rom all looks good, wipe caches and reboot.. than goes to the cool cm10 logo and loops there for AGES like 30 mins than i power cycled it and tried over.
with no working cm10 there i looked around and followed a guide to fastboot a new boot.img on from out of the cm10 zip.
this looked like it was going to work but still reboot and bootlooping.
can anyone help please.
Click to expand...
Click to collapse
try this.
1.) Download the 10/27 build
2.) get the boot.img from this build
3.) wipe cach/dalvik and system
4.) install 11/2 nightly
5.) flash the 10/27 boot.img
6.) reboot
This worked for me, something with the 11/2 and 11/1 boot.img was keeping it from booting.
Good luck
yching07 said:
can I just use TWRP to install CyanogenMod 10 with it? or do I need another installer of roms like CWM Recovery?
Click to expand...
Click to collapse
I would only recommend TWRP with CM10, or any other ROM.
Problems with CMW are due to the fact that it never officially supported our device, and was just a port. TWRP has no such issues.
redpoint73 said:
I would only recommend TWRP with CM10, or any other ROM.
Problems with CMW are due to the fact that it never officially supported our device, and was just a port. TWRP has no such issues.
Click to expand...
Click to collapse
Ohh okok, great thanks, I already installed the TWRP 2.3 from goomanager, lets see if I get the courage to use cm10
yching07 said:
Ohh okok, great thanks, I already installed the TWRP 2.3 from goomanager, lets see if I get the courage to use cm10
Click to expand...
Click to collapse
You don't need courage to do that. You need patience, reading and common sense.. Good luck
Sent from my HTC One XL using xda premium
I have S3 right here and I tried flashing Trickdroid ICS, JB as well as JellyBean Official TWRP zip.
It is S-ON, so after flashing the zip, I go to fastboot and flash boot.img.
I did it already 2-3 times with every rom, but every time I get boot loop. Phone restarts as soon as the first HTC logo disappears.
What is wrong with that?
Do you have the latest TWRP 2.4.1.0 ? (did you try reflashing your recovery?)
What android did you have before unlocking your bootloader? 4.0.3 or 4.0.4?
(and don`t panic If nothing works there is always a solution by relocking your phone and flash the ruu for your phone from here)
http://www.androidfiles.org/ruu/?dir=VilleC2
take a look here:
http://forum.xda-developers.com/showpost.php?p=37498221&postcount=309
impactor said:
I have S3 right here and I tried flashing Trickdroid ICS, JB as well as JellyBean Official TWRP zip.
It is S-ON, so after flashing the zip, I go to fastboot and flash boot.img.
I did it already 2-3 times with every rom, but every time I get boot loop. Phone restarts as soon as the first HTC logo disappears.
What is wrong with that?
Click to expand...
Click to collapse
What's was you on before flashing a custom rom? because just a guess but I think it was 4.0.3 if that is so then try TrickDroid for S3 and get v3 which is 4.0.3 so should work.
It was stock, but I didn't check the version before flashing.
So, TD 3.0, then TD 5.0 and it will work?
By the way, what is better? TD 5.0 or JellyBean Official TWRP?
impactor said:
It was stock, but I didn't check the version before flashing.
So, TD 3.0, then TD 5.0 and it will work?
By the way, what is better? TD 5.0 or JellyBean Official TWRP?
Click to expand...
Click to collapse
No only v3 but if you can get an RUU thats more up to date then do that and the v4/5 should work.
So you didn't install a custom kernal before
Sent from my KFTT using xda premium
KindleFireGuy said:
So you didn't install a custom kernal before
Sent from my KFTT using xda premium
Click to expand...
Click to collapse
Em what he said he did.
You cannot flash S4 roms with an S3 phone, have you made sure that the Roms you flash are specifically assigned for S3? Cuz most are S4
Thanks, guys. That was HBOOT problem. I flashed latest RUU and then I was able to use JB roms.
I am terribly sorry to bump this thread but it is EXACTLY what I need. I read through it and am slightly confused with what you guys said.
Here's my situation:
I have a HTC Evo 3D and have tried running multiple ROMs and on every ROM I run into a boot loop. I use TWRP 2.2.0 and boot that onto my phone using the code "Fastboot boot twrp-shooter.img", then from there I go into TWRP and add the ROM to the root of my SDcard. Then I use TWRP to wipe my cache, delvik cache, system, and do a factory reset. Then I go to install from SDcard and install my desired ROM that I am trying. It is successful and when I reboot it shows the HTC logo, then the loading screen for the ROM, then it goes black, then back to the HTC logo and it continues to loop the same booting sequence over and over.
Am I doing something wrong? Is there something different that I should use or do?
I've been trying to figure out this issue for more than 36 hours and I am borderline psycho right now, I really need answers!
pcout64 said:
I am terribly sorry to bump this thread but it is EXACTLY what I need. I read through it and am slightly confused with what you guys said.
Here's my situation:
I have a HTC Evo 3D and have tried running multiple ROMs and on every ROM I run into a boot loop. I use TWRP 2.2.0 and boot that onto my phone using the code "Fastboot boot twrp-shooter.img", then from there I go into TWRP and add the ROM to the root of my SDcard. Then I use TWRP to wipe my cache, delvik cache, system, and do a factory reset. Then I go to install from SDcard and install my desired ROM that I am trying. It is successful and when I reboot it shows the HTC logo, then the loading screen for the ROM, then it goes black, then back to the HTC logo and it continues to loop the same booting sequence over and over.
Am I doing something wrong? Is there something different that I should use or do?
I've been trying to figure out this issue for more than 36 hours and I am borderline psycho right now, I really need answers!
Click to expand...
Click to collapse
1. check if you are s-on or s-off. If you are s-on, you will also need to flash the kernel (boot.img) from a computer (after you flash the zip)
2. make sure your rom is compatible with your phone
asdfasdfvful said:
1. check if you are s-on or s-off. If you are s-on, you will also need to flash the kernel (boot.img) from a computer (after you flash the zip)
2. make sure your rom is compatible with your phone
Click to expand...
Click to collapse
I already know that I am s-on, and that all I need is the RUU because all I want is to get right the hell back to stock. The problem is that I can't find a RUU that is compatible with my phone!! Your help searching for one would be amazing!!
HTC Evo 3D CDMA Sprint
Mainver: 2.95.652.5
CID: SPCS_002
pcout64 said:
I already know that I am s-on, and that all I need is the RUU because all I want is to get right the hell back to stock. The problem is that I can't find a RUU that is compatible with my phone!! Your help searching for one would be amazing!!
HTC Evo 3D CDMA Sprint
Mainver: 2.95.652.5
CID: SPCS_002
Click to expand...
Click to collapse
Still new to xda, but check this out?
http://forum.xda-developers.com/wiki/HTC_Evo_3D/CDMA
(ctrl + f and find "ruu")
My mainver is not listed, I have already seen this page
The page was last edited in November of 2012, I think it's a bit out of date
Hi,
I have managed to put on a kernel that's not working. Is there a way to revert back to the original kernel? I do have a nandroid backup, but re-installing that didn't put on the old kernel.
I am using Liquidsmooth ROM. Any help would be appreciated.
Thanks.
if you can boot into the rom use flashimagegui, if not do the normal fastboot the boot.img then do it again with flashimagegui to get the modules.
what kernel did you try to flash? the only kernel that will work with new liquidsmooth is cm10.1_vz-oc-linaro.3.zip. it contains modules, if you aren't s-off then you need to flash boot.img in fastboot then flash again in recovery for the modules.
DvineLord said:
if you can boot into the rom use flashimagegui, if not do the normal fastboot the boot.img then do it again with flashimagegui to get the modules.
what kernel did you try to flash? the only kernel that will work with new liquidsmooth is cm10.1_vz-oc-linaro.3.zip. it contains modules, if you aren't s-off then you need to flash boot.img in fastboot then flash again in recovery for the modules.
Click to expand...
Click to collapse
I did exactly that, presuming that it was working... But I have been facing issues. The phone restarts every once in a while and I have managed to get to this condition after multiple wipes and restoring a backup. Anyways I don't know what the issue is I was just wondering how to revert back to the original kernel.
im running Liquid-JB-v2.1-RC2-evita.zip and cm10.1_vz-oc-linaro.3.zip. there seem to be some general issues with the rom that present as basically glitching and gets worse overtime atleast for me. im pretty sure it isnt related to the kernel. but to revert kernel just load the liquidsmooth zip into flashimagegui and itll pull the needed files, let it wipe cache and dalvik then reboot.
DvineLord said:
im running Liquid-JB-v2.1-RC2-evita.zip and cm10.1_vz-oc-linaro.3.zip. there seem to be some general issues with the rom that present as basically glitching and gets worse overtime atleast for me. im pretty sure it isnt related to the kernel. but to revert kernel just load the liquidsmooth zip into flashimagegui and itll pull the needed files, let it wipe cache and dalvik then reboot.
Click to expand...
Click to collapse
I do not have s-off does the flashimagegui works even without it?
strommer666 said:
I do not have s-off does the flashimagegui works even without it?
Click to expand...
Click to collapse
yes, Flash Image GUI
you should also s-off your phone it will make life ALOT easier and the process is simple take like 2 minutes.
DvineLord said:
yes, Flash Image GUI
you should also s-off your phone it will make life ALOT easier and the process is simple take like 2 minutes.
Click to expand...
Click to collapse
Thanks I'll make sure I do that..
also new stable build of liquidsmooth just got released. you should flash it. imma flash it with a clean full wipe. but you should s-off first so you dont have to flash boot.img separately every rom.
DvineLord said:
also new stable build of liquidsmooth just got released. you should flash it. imma flash it with a clean full wipe. but you should s-off first so you dont have to flash boot.img separately every rom.
Click to expand...
Click to collapse
Ya, I saw the new version wanted to try that which is why I wanted to got to the old kernel version. I had tried installing it with the linaro kernel but it gets stuck on the boot screen.
Update: - I installed the flash gui image, then extracted and installed the kernel , factory reset the phone, then installed the latest liquid smooth build. But it is still not going ahead of the boot animation.
Update 3 :- Got the old kernel back. Did a restore. Working fine now . But still for some reason I cannot install the new ROM yet.
strommer666 said:
Ya, I saw the new version wanted to try that which is why I wanted to got to the old kernel version. I had tried installing it with the linaro kernel but it gets stuck on the boot screen.
Update: - I installed the flash gui image, then extracted and installed the kernel , factory reset the phone, then installed the latest liquid smooth build. But it is still not going ahead of the boot animation.
Update 3 :- Got the old kernel back. Did a restore. Working fine now . But still for some reason I cannot install the new ROM yet.
Click to expand...
Click to collapse
you need everything. you don't need to extract the kernel. just load the whole zip file.
DvineLord said:
you need everything. you don't need to extract the kernel. just load the whole zip file.
Click to expand...
Click to collapse
I did load the full file and the flash gui image extracted the kernel. The thing is I have the kernel now, but still I can't seem to be able to install the new version of the LiquidSmooth build. I am doing a nandroid backup of this thing and try installing it again.
well new liquidsmooth is nice, im using cwm now as recovery since ive had tons of issues with twrp since version 2.2.2.0
Hello.
I've got problem with installing ROM Android Revolution HD 7.3. I bought Sensation, it's rooted, S-OFF, bootloader is unlocked, 4EXT Recovery Touch, I've flashed Universal Firmware 3.33. I done wipe data and wipe cache, flashed ROM but after reebot it's stuck on Beats logo. Nothings happened. I also tried do full wipe by superwipe script for Sensation, but that doesn't help. It still stucks on Beats logo. I aslo tried to flash boot.img via flashboot and cmd command. I unziped ROM file, found boot.img file for kernel which I want to install (faux) and flash it via fastboot. Then install ROM via installer included into ROM. After that it doesn't work either.
Can someone help me? I manage to flash different ROM: CM11 with ION and 3.0 kernel by Sultan, but i want to try Android Revolution HD. Maybe my battery will live longer
I appreciate any help.
how long did you wait on beats audio logo? because first boot up takes time
Couple of minutes. No longer then 10, for sure. You think I should wait longer?
robkow said:
Couple of minutes. No longer then 10, for sure. You think I should wait longer?
Click to expand...
Click to collapse
nope , i think 10 min is enought..
Ok. Maybe someone else have a solution.
By the way, I see you've got a ViperS 5.1.0 ROM. Could you tell me how it's works? Especially the battery lifespan.
robkow said:
Ok. Maybe someone else have a solution.
By the way, I see you've got a ViperS 5.1.0 ROM. Could you tell me how it's works? Especially the battery lifespan.
Click to expand...
Click to collapse
For me is great , but you have to try it yourself
for ARHD 7.3 ROM if it has in aroma installer to choose a kernel try with the stock one and see if it boots
make a full wipe from recovery before flashing the rom
I've already tried every one of 3 included. But I will try do it again now and wait for longer on Beats logo.
robkow said:
I've already tried every one of 3 included. But I will try do it again now and wait for longer on Beats logo.
Click to expand...
Click to collapse
what recovery do you have?
4EXT Recovery Touch v1.0.0.5 RC5
robkow said:
4EXT Recovery Touch v1.0.0.5 RC5
Click to expand...
Click to collapse
try to update to the latest one
even redownload the rom and check md5 sums
I reinstal ROM again and it works. I don't know why, but it works. Thanks everyone for help, though