TF201/700 Dock Feet - Asus Transformer TF700

So I've got to say that every aspect of having the dock for my TF700 Infinity is absolutely outstanding. Though I have had one issue that is seeming to become worse.
The "feet" on the dock have started to come off. So far I have lost two of them, without a clue as to where they have gone. I called ASUS, and they said that if I were lucky they might have them for sale on there site, which they don't. They also said that these missing feet would not be covered under warranty if I were to even go through the hassle of sending it back to them.
So this brings the question. Does anyone know where I can either get replacement feet, or what I might be able to fabricate new feet out of? I wouldn't normally care about the feet, except that they do a wonderful job of keeping the tablet and dock from sliding around on my desk. I honestly wouldn't even mind adding a mm or two to the back feet so that they could do a better job of that while the tablet/dock are opened.
Any suggestions on a rubber type material, or other such material, that I could use to create some new feet? I'd be willing to make them for the community also if I could just find the right material. I am sure that I'm not the only one being plauged by this issue, maybe it's just bothering me more than most.
-FInire

Try on ebay - I've replaced the rubber feet on one of our laptops - there was a huge choice and managed to fine ones better than the originals.
Although not sure you'll get a colour match, I'm sure the sizes will be available in a number of heights.

Try a decoration or furniture store, they usually sell rubber non-slip anti-scratch stickers for under decorative items. They work rather well under the dock, too.

Finire said:
So I've got to say that every aspect of having the dock for my TF700 Infinity is absolutely outstanding. Though I have had one issue that is seeming to become worse.
The "feet" on the dock have started to come off. So far I have lost two of them, without a clue as to where they have gone. I called ASUS, and they said that if I were lucky they might have them for sale on there site, which they don't. They also said that these missing feet would not be covered under warranty if I were to even go through the hassle of sending it back to them.
So this brings the question. Does anyone know where I can either get replacement feet, or what I might be able to fabricate new feet out of? I wouldn't normally care about the feet, except that they do a wonderful job of keeping the tablet and dock from sliding around on my desk. I honestly wouldn't even mind adding a mm or two to the back feet so that they could do a better job of that while the tablet/dock are opened.
Any suggestions on a rubber type material, or other such material, that I could use to create some new feet? I'd be willing to make them for the community also if I could just find the right material. I am sure that I'm not the only one being plauged by this issue, maybe it's just bothering me more than most.
-FInire
Click to expand...
Click to collapse
Dude, i have the answer!!! ............i have found the feet that are perfect nearly 99.5% the same as the originals. I just need to find the ebay sellers name from my emails, as the auction i bought from has been archived. I will post back later tonight with the answer

If you have a friend or you yourself owns a Hot glue gun then you can just put a tiny dolop of hot glue where the feet used to be. It should stay for a long while and they are just as good as a silicone nub or foot for these products. my wife has one of these thats the only reason why it came up. Otherwise i would go to Home Depot, by me they have a huge selection of these kinds of things for furniture.

vtec2k7 said:
If you have a friend or you yourself owns a Hot glue gun then you can just put a tiny dolop of hot glue where the feet used to be. It should stay for a long while and they are just as good as a silicone nub or foot for these products. my wife has one of these thats the only reason why it came up. Otherwise i would go to Home Depot, by me they have a huge selection of these kinds of things for furniture.
Click to expand...
Click to collapse
Alternatively, if you have a friend that has the same dock, steal his/her dock's

fincan said:
Alternatively, if you have a friend that has the same dock, steal his/her dock's
Click to expand...
Click to collapse
I can not lie, the thought has crossed my mind. But alas, all I have are friends that druel over mine telling me how much they want it

vtec2k7 said:
If you have a friend or you yourself owns a Hot glue gun then you can just put a tiny dolop of hot glue where the feet used to be. It should stay for a long while and they are just as good as a silicone nub or foot for these products. my wife has one of these thats the only reason why it came up. Otherwise i would go to Home Depot, by me they have a huge selection of these kinds of things for furniture.
Click to expand...
Click to collapse
I've got one myself actually. I'm just hesitant about doing something possibly so permanent. Also, I know if I can't get it just right, flat and all... It's really going to bug the crap out of me too... Not saying it's a bad idea, it's a great one... I'm just finding that I have to weigh it against my ocd...

The hot glue gun sounds like a great idea. I'll be trying that later today on my wife's laptop.

effezie said:
The hot glue gun sounds like a great idea. I'll be trying that later today on my wife's laptop.
Click to expand...
Click to collapse
If you can post pictures after you've gotten it done I'd love to see how it turns out.

a small dab of RTV Silicone works well too. I've been doing that on my laptops for years.

I gave up... I used hot-glue... It works perfectly! And it's easily removable if need be. The only difficult part is getting it shaped correctly.

Hot glue works. I've used Sugru on my laptop feet. Love that stuff...
Sent from my ASUS Transformer Pad TF700T using xda premium

Found these online. Seem like they would probably work:
http://www.radtech.us/products/Pawz.aspx

HuskerWebhead said:
Found these online. Seem like they would probably work:
http://www.radtech.us/products/Pawz.aspx
Click to expand...
Click to collapse
Those look quite nice. I'm going to order them, and hope that they stick on over my Skinomi. If not, I'll get the exacto blade out and carve them up to the right size.
I've had to replace my superglue feet twice so far, as they keep coming off.

Related

armband?

Anyone found a suitable armband to go running/work out in while keeping my lovely g2x safe and sound from falling out or getting my sweat all over?
or if you have a universal sized armband and are having success with your g2x in it please do share your experiences!
EDIT:
Review of the VanGoddy Armband: http://forum.xda-developers.com/showpost.php?p=14056733&postcount=16
Check Amazon.
http://www.amazon.com/gp/aw/s/ref=is_box_/181-1178860-7666418?k=g2x+arm+band
Check out the third choice . LOL
Sent from my LG-P999 using XDA Premium App
KRAZYADROIDMASTER said:
Check Amazon.
http://www.amazon.com/gp/aw/s/ref=is_box_/181-1178860-7666418?k=g2x+arm+band
Check out the third choice . LOL
Sent from my LG-P999 using XDA Premium App
Click to expand...
Click to collapse
[email protected] choice!
yea i looked at those armbands that are on amazon and I am not too wild about them... right now my biggest candidate is the adidas miCoach armband...
http://www.google.com/products/cata...=X&ei=chXSTZDEJoWftwfhsOyXCg&ved=0CG0Q8wIwAA#
though it is nylon and i dont know how i feel about nylon... i would prefer neoprene...
looking for an armband as well. All I saw were those few amazon entries and one bad review that said the phone sticks up above the cover. I might go to target and try a bunch for the iphone.
kev0153 said:
looking for an armband as well. All I saw were those few amazon entries and one bad review that said the phone sticks up above the cover. I might go to target and try a bunch for the iphone.
Click to expand...
Click to collapse
Well I am going to take one for the team, I ordered the one that amazon has listed with the ONE bad review... for 17 bux shipped so its whatever...
i went to best buy today and opened a bunch of boxes of stuff and nothing seemed to really fit... i tried the miCoach for the IP4 and it was a huge fail
I pondered using my tunebelt from my nexus one and just getting a different silicone case but with the phone being as big as it is and 12 grams heavier that it may be a little too flimsy and flopping around for my liking...
I want something with the form factor that the amazon armbands or miCoach has where the phone fits into a sleeve and wont flop around... assuming the phone does not stick out literally an inch and the phone will stay in when I am jogging or doing plyometrics, i will be happy with my purchase...
full review to come when i get it...
Thanks looking forward to the review.
Sent from my LG-P999 using XDA Premium App
kev0153 said:
looking for an armband as well. All I saw were those few amazon entries and one bad review that said the phone sticks up above the cover. I might go to target and try a bunch for the iphone.
Click to expand...
Click to collapse
yup... looking for a perfect fit one too.
Try sports authority
shopcity said:
Try sports authority
Click to expand...
Click to collapse
I dont have sports authority and ****'s said they only carry ipod accessories, specifically nano armbands... its more of a bestbuy type of store's job to carry smartphone sports armbands since they actually sell the devices... ipods are a little more universal so ****'s carrys them...
kev0153 said:
looking for an armband as well. All I saw were those few amazon entries and one bad review that said the phone sticks up above the cover. I might go to target and try a bunch for the iphone.
Click to expand...
Click to collapse
I have the exact same problem the only armband that I found on Amazon supposedly sucks doesn't even fits the entire phone
I'm subscribing to this thread hopefully I'll find something nice
JHaste said:
Well I am going to take one for the team, I ordered the one that amazon has listed with the ONE bad review... for 17 bux shipped so its whatever...
i went to best buy today and opened a bunch of boxes of stuff and nothing seemed to really fit... i tried the miCoach for the IP4 and it was a huge fail
I pondered using my tunebelt from my nexus one and just getting a different silicone case but with the phone being as big as it is and 12 grams heavier that it may be a little too flimsy and flopping around for my liking...
I want something with the form factor that the amazon armbands or miCoach has where the phone fits into a sleeve and wont flop around... assuming the phone does not stick out literally an inch and the phone will stay in when I am jogging or doing plyometrics, i will be happy with my purchase...
full review to come when i get it...
Click to expand...
Click to collapse
What case do you have?
I want to have a good case that hopefully also fits in a good armband
Let me know if you find a good combination please I'd appreciate it
Here is a list of armbands I found on Amazon, I think the only solution would be to buy a an armband not designed specifically for the G2X and see which one adapts the best
http://www.amazon.com/gp/search/ref=sr_nr_i_1?rh=k%3Acell+phone+armband%2Ci%3Amobile&keywords=cell+phone+armband&ie=UTF8&qid=1306020133
http://www.amazon.com/iArmbands-Arm..._1_7?s=wireless&ie=UTF8&qid=1306060005&sr=1-7
Found this one: http://www.amazon.com/Elegant-Armba..._14?s=wireless&ie=UTF8&qid=1306075830&sr=1-14
Zspy1985 said:
http://www.amazon.com/iArmbands-Arm..._1_7?s=wireless&ie=UTF8&qid=1306060005&sr=1-7
Click to expand...
Click to collapse
the band is too thin, that phone would flap all over the place with a phone our size... bands with a sleeve are better in terms of comfort and stability
omarsalmin said:
Found this one: http://www.amazon.com/Elegant-Armba..._14?s=wireless&ie=UTF8&qid=1306075830&sr=1-14
Click to expand...
Click to collapse
yea that is the one i ordered that got the couple of bad reviews...
I just got it in the mail yesterday but I was not home to use it, I will take it out for jog tonight and do a full review with some pictures
JHaste said:
the band is too thin, that phone would flap all over the place with a phone our size... bands with a sleeve are better in terms of comfort and stability
yea that is the one i ordered that got the couple of bad reviews...
I just got it in the mail yesterday but I was not home to use it, I will take it out for jog tonight and do a full review with some pictures
Click to expand...
Click to collapse
Thanks for your upcoming review I appreciate that
Ok so here is my review of the VanGoddy Armband for the G2x/O2X/EVO4g/Atrix/any other giant ass phone!
(Picture album is linked on the bottom of the post)
First off I would like to state what sort of view I am coming from as to eliminate any bias by stating my biases from the get go. I am a slim, athletic body type, 14 inch biceps, 6 foot, 160 pounds. I typically will be doing a lot of running with this device and I referee soccer and will often strap it on while I run a game so I can track my positioning, distance, ect. so I wanted a band that would not be too gaudy and I could hide a bit under my sleeves (underarmor and uniform sleeves). Since again running was my main use with some use in the gym I wanted stability while holding the device so it was not sliding around, flopping around or possibly flying out of the pocket. The other main feature I was looking for was material quality and anybody that works out knows neoprene is clutch especially for people who sweat a large amount, like myself, when I work out or go running. Tad bit of personal information for ya there!
The unboxing and first impressions: VanGoddy shipped it in a bubble wrap envelope, nothing fancy and the item did not need anything fancy. Right away when I looked the thing over I could tell that the pocket to hold the phone looked a tad large for my phone and that the plastic screen was cheap and small. Just putting the armband on, I put it on as tight as I could get the velcro to go and it was a perfect fit, very snug and even tighter when I flexed how my arms would be while running.
Upon slotting the phone in I noticed two things, the clear screen cover does in fact suck, and the phone will fall out of the slot naturally. The device was definitely made with a "universally wide" pouch and I would argue favors the wider phones such as the Atrix, Evo4g and DX; our slim phones got the shaft in this design. I put the armband back on, tightened up, even loosened it a hair from where I had it last time and boom! it actually felt pretty good. Swinging my arm around the phone was pretty snug, I could not get it to fall out regardless of what I was doing which earned it some "do points" in the do or die ratings! I would clear this for use in the gym for bench pressing and doing other strange arm angle lift routines.
Onto the screen cover. This was my biggest grip with this thing. You do not get a lot of cover real estate to work with and the way the cover was stitched into the armband was absolutely thoughtless because it does not even come close to sitting flush with the screen. The part that is stitched around the screen on the outside is a flexible plastic and on the inside they overlapped material so that the screen is not sitting against the plastic cover screen. (See picture overlap flap) This caused another problem that annoyed me a little, if the phone shifted in the slot too much to one way or the other the edge of the phone would get caught on one of these flaps on the inside around the screen edge and offset the phone. It did this twice during my little 3 mile jog while I was trying to skip a song. Getting to the notifications bar while in the slot is damn near impossible, I had no trouble hitting the softkeys but the notification bar is inaccessible. This is partly due to the long "ass" our phones have so the top part of our screens will not be within the clear cover's viewing range.
I did and do not play with the phone much while running because I have very satisfying playlists. Handling touches through the screen was about on par with other covers of similar thickness. I did not really have a problem executing touch commands but changing the volume was a little weird since I had to essentially just squeeze and guess where the volume buttons were on the side. On the bright side, because the screen is not very tight to the screen and the neoprene resists water, I never noticed the screen to fog up on me.
All in all for $17 something cents shipped this is not a terrible armband by any means. It is no 30-40 dollar custom phone fitting armband but it is not so cheap that I just pitched it laughing at what I bought, I would say I got what I paid for and maybe a bit more. Score wise I would give this guy a 7/10. It is good but it definitely has some shortcomings. If you are skinny and dont have at least a 13inch bicep I would not recommend you purchase this device, for fear of it sliding off of your arm. Get used to running with this on your left arm, I found the cord positioning much better and it was getting tangled less around my arm.
Some things I would have liked to see and would be a more quality screen cover. A bit more velcro (one more inch) to possibly go tighter for maybe some more extreme sports or intense working out and for smaller biceps. A slot for a Key is always a nice addition but I usually find a place in whatever pair of shoes I have; sliding it behind the phone you would risk it flying out, I would bet money that it flies out on smaller biceps.
If you are looking for something to get the job done then this is the device for you because it does exactly that. It does not do it extremely well, wow, or impress me in any way but it for 17 bucks it served my needs. Again 7/10 from me...
Pictures: https://picasaweb.google.com/108804...?authkey=Gv1sRgCMyb25S03-aJDw&feat=directlink
Enjoy and Thanks for reading!
thanks for the great review. It sounds like this is the best one out there right now.
Just bought one, hopefully it will be sufficient. Just need it to keep the thing dry
swampthing1224 said:
Just bought one, hopefully it will be sufficient. Just need it to keep the thing dry
Click to expand...
Click to collapse
I dont think you will have any problem keeping it dry, just make sure nothing from your shoulder or upper arm drips down since the top is open
http://www.amazon.com/iGadgitz-Resi..._1_4?s=wireless&ie=UTF8&qid=1306182082&sr=1-4
found this one but it's out of stock. try emailing the seller?

Are the Nexus 9 Folio covers reversible?

Since the folio covers are 2 sided with different colors, I'm wondering: can you flip the folio case over if you want to change colors?
I like the peach/maroon colored folio cover (Coral Amethyst), but I would much rather have the Maroon showing for the front than the Peach side shown in stock photos.
I think the Vietnamese YouTube review video floating around showed the lime cover attached, with the lime facing out on the back of the device. That would mean that if you close the cover, the lime is inside, and the darker navy (?) is on the outside. It would seem to be reversible.
you can teach me how to do this okay?
---------- Post added at 03:03 AM ---------- Previous post was at 02:43 AM ----------
What I usually just hand
bailyc said:
I think the Vietnamese YouTube review video floating around showed the lime cover attached, with the lime facing out on the back of the device. That would mean that if you close the cover, the lime is inside, and the darker navy (?) is on the outside. It would seem to be reversible.
Click to expand...
Click to collapse
I watched the cover in use in a french video posted in another thread, and it doesn't look like there hinges to close the cover, like you're imagining. Looking at the video, it looks like you peel the cover entirely off the front and then stick it to the back, and vice versa. It doesn't seem to fold around on a hinge like the iPad smart cover. In which case, I guess you can probably stick it to the tablet in either direction each time you "close" it. I wish it had the hinge though. I don't really want to buy a cover that comes entirely off every time I want to use my tablet...
mrkvchm said:
I watched the cover in use in a french video posted in another thread, and it doesn't look like there hinges to close the cover, like you're imagining. Looking at the video, it looks like you peel the cover entirely off the front and then stick it to the back, and vice versa. It doesn't seem to fold around on a hinge like the iPad smart cover. In which case, I guess you can probably stick it to the tablet in either direction each time you "close" it. I wish it had the hinge though. I don't really want to buy a cover that comes entirely off every time I want to use my tablet...
Click to expand...
Click to collapse
You're right. The first video review was out before the French one, and didnt show it being taken off and put on the back, I think. From the French video, I agree, it appears hingeless, but it is probably reversible. I still have one pre-ordered from Amazon but, ugh, I kind of want it attached in some way too. But who knows! Maybe from now on I will prefer ones that come off entirely. Those magnets better be strong enough to keep it from shifting or flopping around.
bailyc said:
You're right. The first video review was out before the French one, and didnt show it being taken off and put on the back, I think. From the French video, I agree, it appears hingeless, but it is probably reversible. I still have one pre-ordered from Amazon but, ugh, I kind of want it attached in some way too. But who knows! Maybe from now on I will prefer ones that come off entirely. Those magnets better be strong enough to keep it from shifting or flopping around.
Click to expand...
Click to collapse
And that's the thing as well. I don't want to pull my tablet out of a bag and have the cover left behind. But my other issue with it is that it seems like it will be a hassle to take it off and put it on. The iPad smart covers are so easy to flip open and closed with one hand because you don't have to line it up and you only have to grab one side of it. Seems like moving the magic cover around may be quite the ordeal. I might end up getting one anyways, I don't know. Since I can't seem to order one to Canada yet anyways, I guess I'll wait and see how everyone else ends up liking it. In the meantime, my nexus 9 will either be naked or wearing a MOFRED Ultra Slim case (basically a smart cover knockoff) that I managed to order from the UK for £0.01 haha
mrkvchm said:
And that's the thing as well. I don't want to pull my tablet out of a bag and have the cover left behind. But my other issue with it is that it seems like it will be a hassle to take it off and put it on. The iPad smart covers are so easy to flip open and closed with one hand because you don't have to line it up and you only have to grab one side of it. Seems like moving the magic cover around may be quite the ordeal. I might end up getting one anyways, I don't know. Since I can't seem to order one to Canada yet anyways, I guess I'll wait and see how everyone else ends up liking it. In the meantime, my nexus 9 will either be naked or wearing a MOFRED Ultra Slim case (basically a smart cover knockoff) that I managed to order from the UK for £0.01 haha
Click to expand...
Click to collapse
I'm not sure about the status of my Amazon order (still says not yet shipped), but it is supposed to arrive on Wednesday. So is my tablet but again, still not shipped yet. I'll give a quick update when they get here and I have a chance to try it out. It's a $40 gamble but I usually end up liking the OEM accessories, as overpriced as they are.
bailyc said:
I'm not sure about the status of my Amazon order (still says not yet shipped), but it is supposed to arrive on Wednesday. So is my tablet but again, still not shipped yet. I'll give a quick update when they get here and I have a chance to try it out. It's a $40 gamble but I usually end up liking the OEM accessories, as overpriced as they are.
Click to expand...
Click to collapse
Well it seems like we have the same reservations about it, so I'll be interested in hearing what you think.
mrkvchm said:
I watched the cover in use in a french video posted in another thread, and it doesn't look like there hinges to close the cover, like you're imagining. Looking at the video, it looks like you peel the cover entirely off the front and then stick it to the back, and vice versa. It doesn't seem to fold around on a hinge like the iPad smart cover. In which case, I guess you can probably stick it to the tablet in either direction each time you "close" it. I wish it had the hinge though. I don't really want to buy a cover that comes entirely off every time I want to use my tablet...
Click to expand...
Click to collapse
I can see how you can make the assumption that you can just flip the cover around, but then you're not accounting that flipping around the cover could reverse the polarity of the magnet, thereby making the other side of the cover repel away from the tablet rather than being attracted to it. I hope I'm wrong though..
mkygod said:
I can see how you can make the assumption that you can just flip the cover around, but then you're not accounting that flipping around the cover could reverse the polarity of the magnet, thereby making the other side of the cover repel away from the tablet rather than being attracted to it. I hope I'm wrong though..
Click to expand...
Click to collapse
Oh that's an interesting point. I would have never thought of that.... Man, that would be dumb. Well, when someone finally gets one, they'll have to settle all these questions for us once and for all.
mrkvchm said:
Oh that's an interesting point. I would have never thought of that.... Man, that would be dumb. Well, when someone finally gets one, they'll have to settle all these questions for us once and for all.
Click to expand...
Click to collapse
I am convinced that i is reversible. If you look at the product page on Google Play, towards the bottom you see two renderings of the cover. Using the green/blue one as an example, the image next to Takes Pictures in a Snap shows it attached to the back, blue side in, green side out, and the corner is folded over.
Immediately below that is another rendering of the cover as a typing stand for the tablet in landscape mode. Blue side is now out, green side is in, and presumably, it's still magnetically attached along that top edge.
But here's an update on the arrival -- I spoke to an Amazon representative this morning who said that they were informed that the covers have been delayed from the manufacturer, and that no retailer has them in stock right now. She said Amazon has been told that they'll receive a shipment on December 1. So, looks like we will all keep waiting to find out for sure.
I think it will work. Magnets repel each other when the poles are opposite while this is magnet to metal which is different. Somebody with a fridge magnet should be able to check easily.
smf61 said:
I think it will work. Magnets repel each other when the poles are opposite while this is magnet to metal which is different. Somebody with a fridge magnet should be able to check easily.
Click to expand...
Click to collapse
There are in fact magnets in the tablet itself. If you put two Nexus 9 next to each other, side by side, the two tablets will repel each other. I saw a youtube video of this somewhere showing this.
Is nobody concerned about the "inside" of the cover (i.e. the part facing the display) being used as the stand in the upright position? I'm a bit paranoid of it massaging dust/dirt particles into the screen...

Dropped my Moto X Pure for the 100000x time. [TLDR: Broke :( ]

So today i have finally broke my phone I am currently phoneless until my replacement screen comes in so i will be going phoneless from here until atleast 4/20!! So i would like to describe what happened. Usually this phone is a tank and i can drop it 1 million times without it breaking until today happened. I was already having a really bad day i woke up late in the morning and almost missed my bus. i went to school looking like trash and then i end up going through the whole day with a really bad headache. I had to deal with a horrible mat teacher who gave me a (no joke) 66.60 for the marking period. half the class failed. So whatever i dealt with her then i went through my day until i was in my last period class. i was wearing gym shorts today so my pockets were really loose and i had my phone in my right pocket. I was sitting in a chair that was 2 feet off the ground and BAM my phone smashes into the floor. At this point I'm like "oh crap its done" so i flip it over and there was only a tiny crack in the top left hand corner so im like oh okay no biggy I can deal with that. That wasn't the worst of it. The screen powered on perfectly fine nothing looked wrong however only one half of the touch screen worked. Touching the screen anywhere under the power button wouldn't work. Running a DPI of 420 puts 2 essential things right in that exact area (dpi wont matter for the second thing) 1. My lock password is toast so i cant unlock my phone 2. even if i could unlock my phone (some cases i was able to unlock my phone but it works for 5 seconds then stops) the nav bar lives in that zone so im screwed. I just find it funny how a tiny drop can be so fatal and disable half a screen while i drop my phone daily from many different heights and thee wort it got was a scratch. I'm curious what are your drop stories?????
PS. if you don't see me participate in the threads I usually stalk its because I prefer to browse and post to XDA from XDA Labs. The website sucks.
I have repaired my phone and ordered the black dualpro or whatever its called case by insipio I ended up getting it for $25 should be here in a few days the company who ships it is very reliable
photos to follow within the week
Same thing happened to me. But replacing the screen on these is really easy, provided you get the screen/digitizer and frame assembly. Ijust did mine last week. Now i wont take off the case again. I have never cracked a screen until this phone. But up and going again.
planedoc said:
Same thing happened to me. But replacing the screen on these is really easy, provided you get the screen/digitizer and frame assembly. Ijust did mine last week. Now i wont take off the case again. I have never cracked a screen until this phone. But up and going again.
Click to expand...
Click to collapse
Yeah i noticed how easy it is! i should be getting my replacement display (with frame) and phone tools anywhwere between now and may 1st
WelcomeToTheSkye said:
Yeah i noticed how easy it is! i should be getting my replacement display (with frame) and phone tools anywhwere between now and may 1st
Click to expand...
Click to collapse
Can you link from where u ordered your screen ?
Simple lesson: keep it in a case
Sent from my XT1572 using XDA-Developers mobile app
Jay794 said:
Simple lesson: keep it in a case
Sent from my XT1572 using XDA-Developers mobile app
Click to expand...
Click to collapse
Maybe if you just got black or something. Some of us customized them in Moto maker or skinned them. It would be useless to cover it up and I don't like the clear cases. Sure you have to be careful but you really should even with a case. The thing is accidents happen and a case isn't a guarantee that the phone won't break anyways.
Jay794 said:
Simple lesson: keep it in a case
Click to expand...
Click to collapse
If only they weren't so ugly for this phone. Good thing I take care of my stuff...
@WelcomeToTheSkye Sorry to hear about your phone. And your class. I was so scared I was gonna drop my MXP until I got a case. I was expecting the rubber on the back to be grippy but mine is slippery compared to my old moto E and the metal makes it worse. If you'd like a case recommendation, I have the Diztronic case and the Incipio Octane. They're both good. The octane looks better because it lets you back material show through and it adds more grip, but the headphone port cutout isn't big enough for my ATH-M50s
The Diztronic is really really nice. It just doesn't add as much grip. The buttons are also really easy to press. It's the one I usually use.
Jay794 said:
Simple lesson: keep it in a case
Click to expand...
Click to collapse
i have never been a case person... i break all the cases i ever get... plus all the cases (beside the incipio brand) suck for this phone
elite001mm said:
@WelcomeToTheSkye Sorry to hear about your phone. And your class. I was so scared I was gonna drop my MXP until I got a case. I was expecting the rubber on the back to be grippy but mine is slippery compared to my old moto E and the metal makes it worse. If you'd like a case recommendation, I have the Diztronic case and the Incipio Octane. They're both good. The octane looks better because it lets you back material show through and it adds more grip, but the headphone port cutout isn't big enough for my ATH-M50s
The Diztronic is really really nice. It just doesn't add as much grip. The buttons are also really easy to press. It's the one I usually use.
Click to expand...
Click to collapse
Yeah i might end up going with the incipio duo thingy lol the one with two layers soon... im just not a case person... thanks for the recommendations
WelcomeToTheSkye said:
i have never been a case person... i break all the cases i ever get... plus all the cases (beside the incipio brand) suck for this phone
Click to expand...
Click to collapse
I got a pretty nice looking carbon fibre look case off eBay for less than £5 and it's saved my phone no end of times, if you go caseless and your phone breaks you only have yourself to blame
Wallet cases are also a great way to protect your phone/screen. I looked around on Amazon for a while and the only well reviewed one was the one by a company called J&D. I purchased it in turquoise and paired it with the Pleson tempered glass screen protector and the only downside is that all tempered glass protectors for this phone come up a little on the sides due to the curved screen but otherwise this is a protective and attractive combination.
Sent from my XT1575 using XDA-Developers mobile app
WelcomeToTheSkye said:
So today i have finally broke my phone I am currently phoneless until my replacement screen comes in so i will be going phoneless from here until atleast 4/20!! So i would like to describe what happened. Usually this phone is a tank and i can drop it 1 million times without it breaking until today happened. I was already having a really bad day i woke up late in the morning and almost missed my bus. i went to school looking like trash and then i end up going through the whole day with a really bad headache. I had to deal with a horrible mat teacher who gave me a (no joke) 66.60 for the marking period. half the class failed. So whatever i dealt with her then i went through my day until i was in my last period class. i was wearing gym shorts today so my pockets were really loose and i had my phone in my right pocket. I was sitting in a chair that was 2 feet off the ground and BAM my phone smashes into the floor. At this point I'm like "oh crap its done" so i flip it over and there was only a tiny crack in the top left hand corner so im like oh okay no biggy I can deal with that. That wasn't the worst of it. The screen powered on perfectly fine nothing looked wrong however only one half of the touch screen worked. Touching the screen anywhere under the power button wouldn't work. Running a DPI of 420 puts 2 essential things right in that exact area (dpi wont matter for the second thing) 1. My lock password is toast so i cant unlock my phone 2. even if i could unlock my phone (some cases i was able to unlock my phone but it works for 5 seconds then stops) the nav bar lives in that zone so im screwed. I just find it funny how a tiny drop can be so fatal and disable half a screen while i drop my phone daily from many different heights and thee wort it got was a scratch. I'm curious what are your drop stories?????
PS. if you don't see me participate in the threads I usually stalk its because I prefer to browse and post to XDA from XDA Labs. The website sucks.
Click to expand...
Click to collapse
Make sure you head over to https://forums.lenovo.com/t5/Moto-X-Pure-Moto-X-Style/bd-p/449 before having Moto Mobility work on it. There's some disagreement over whether it's a scam or negligence, but either way you're in for a lot of trouble.
I don't use a case either because it makes the phone too large for a pocket. Too bad Moto didn't put a rim around the glass like every other Chinese and Japanese phone has. I guess they wanted the iPhone look with a minimalist white face and a cracked screen.
kevinmcmurtrie said:
Make sure you head over to https://forums.lenovo.com/t5/Moto-X-Pure-Moto-X-Style/bd-p/449 before having Moto Mobility work on it. There's some disagreement over whether it's a scam or negligence, but either way you're in for a lot of trouble.
I don't use a case either because it makes the phone too large for a pocket. Too bad Moto didn't put a rim around the glass like every other Chinese and Japanese phone has. I guess they wanted the iPhone look with a minimalist white face and a cracked screen.
Click to expand...
Click to collapse
I repaired it myself! Everything works perfectly...
Sent from my XT1575 using XDA Labs
Im having the same issue,Dropped the phone bought a replacement screen since motorola wants to charge me 250 bucks JUST FOR THE SCREEN but the worst part about all of this is when i removed the phone back i couldnt remove the screws because most of them are stripped :'(. so now im stuck with this phone like this and i dont want to buy a whole new one cause im poor.
pabel101 said:
Im having the same issue,Dropped the phone bought a replacement screen since motorola wants to charge me 250 bucks JUST FOR THE SCREEN but the worst part about all of this is when i removed the phone back i couldnt remove the screws because most of them are stripped :'(. so now im stuck with this phone like this and i dont want to buy a whole new one cause im poor.
Click to expand...
Click to collapse
Same thing happened to me I stripped 6/20 of the screws... Turns out if you rip the screen off by getting a screwdriver under it you can still the stripped screws out of the back frame. It doesn't need all 20 screws it needs the one to hold the motherboard to the screen and at least 8 to keep it in place
Sent from my XT1575 using XDA Labs
pabel101 said:
Im having the same issue,Dropped the phone bought a replacement screen since motorola wants to charge me 250 bucks JUST FOR THE SCREEN but the worst part about all of this is when i removed the phone back i couldnt remove the screws because most of them are stripped :'(. so now im stuck with this phone like this and i dont want to buy a whole new one cause im poor.
Click to expand...
Click to collapse
Everybody says this so I'm betting Leno glued the screws in. It's fixable if it's into plastic. Lift the edge of the screw head with a knife tip as you turn it. Once it's out, clean the threads. Dip a thin wire into plastic welding glue (modeling and pipe glue works) and wet the inside of the screw hole. Clear out any excess glue. Let the glue dry somewhere warm for at least an hour. The screws should fit now.
Can you post a link to the replacement you got? I bought one of the higher priced ones on ebay and have had three with screen issues. The seller just wants to refund me at this point, so I need to find one that will not have light bleed, dead pixels and an unresponsive screen. Thanks in advance!
I am not recommending anyone do this and am not responsible if you mess your phone up. but this worked For my stripped screw. Replaced my screen today. One screw stopped I drilled the head of the screw out. I used a left handed bit because you drill in reverse with these and if the bit grabs it may unscrew. May but didn't. It made me very nervous but worked. And the part of the screw that was left in didn't matter since I bought the screen with the bezzle/frame. And I had a extra screw same size. It was Philips head but worked. There is a good chance if you try to drill out your stripped screws you will completely brake your phone. But there is that small chance for success?

Show me that V20 dent that is driving you crazy!! (Fun post)

The other day I was in the bathroom and forgot that I put my phone on the towel... Got a tiny dent on the corner(Plastic bezel sucks) even though once the cover for it comes in by the 14 of this month is driving me crazy just to see a scratch/dent on it.
Didn't even follow the title. You didn't "show us" anything.
Dont have a cam right now to take a pic. The phone fell and hit the floor with the right bottom corner. Honestly seems more like a chip mark than a dent or a scratch.
People who don't put a case on an expensive device are like guys who don't use condoms with a random girl...I just don't get it...
UPSGuy said:
People who don't put a case on an expensive device are like guys who don't use condoms with a random girl...I just don't get it...
Click to expand...
Click to collapse
I actually order a case but still hasn't arrive.
First thing I get is a case. Even if I have to buy from best buy and pay s premium price. Protection is first priority. After that I'll hit Amazon and get s case I like. I take no chances because you can't undo a drop.
Sent from my LG-H910 using Tapatalk
UPSGuy said:
People who don't put a case on an expensive device are like guys who don't use condoms with a random girl...I just don't get it...
Click to expand...
Click to collapse
Can't get a STD or phone pregnant.
UPSGuy said:
People who don't put a case on an expensive device are like guys who don't use condoms with a random girl...I just don't get it...
Click to expand...
Click to collapse
For most people you're right about the phone - and the random girl.
Yet no one puts cases on their fine crystal Scotch or Cognac glasses - they show them for the fine stemware beauty and art they are designed to be and treat them with care. And no one expects a random girl to be virgin clean ... especially a random that doesn't care if you're goin' in raw-dog.
I've always been disease free my whole life (I'm oooold) because I've chosen wisely .... and I've NEVER used a case on any of my Cell Phones, going all the way back to my first phone in 1992, because I treat them like the fragile glass and electronic pieces of artistic equipment they are.
As much as I agree with the analogy of cases for some people .... I certainly understand why most don't use a case.
Where we probably agree the most is when someone doesn't use a case (or condom) and then complains about how bad their lack of carefulness became a bad situation and blames everything/everyone but themselves.
SaintlySins said:
For most people you're right about the phone - and the random girl.
Yet no one puts cases on their fine crystal Scotch or Cognac glasses - they show them for the fine stemware beauty and art they are designed to be and treat them with care. And no one expects a random girl to be virgin clean ... especially a random that doesn't care if you're goin' in raw-dog.
I've always been disease free my whole life (I'm oooold) because I've chosen wisely .... and I've NEVER used a case on any of my Cell Phones, going all the way back to my first phone in 1992, because I treat them like the fragile glass and electronic pieces of artistic equipment they are.
As much as I agree with the analogy of cases for some people .... I certainly understand why most don't use a case.
Where we probably agree the most is when someone doesn't use a case (or condom) and then complains about how bad their lack of carefulness became a bad situation and blames everything/everyone but themselves.
Click to expand...
Click to collapse
That's why I use a clear case on my v20 with a built in metal kickstand. It shows off the phone but protects it.
The great news is that if you damage the top or bottom of your phone you can replace it by removing the 4 screws on those portions and buying a new chin or forehead. I swapped the bottom chin for a new one when my old one got scratched. It was quick and painless process.
DarkMage619 said:
The great news is that if you damage the top or bottom of your phone you can replace it by removing the 4 screws on those portions and buying a new chin or forehead. I swapped the bottom chin for a new one when my old one got scratched. It was quick and painless process.
Click to expand...
Click to collapse
link to the parts please, I need a 4-head
haha I ended up with getting titan bc im impatient, but i just realized I could always replace the 3 parts with silver and practically have the silver phone.
Sent from my Samsung Galaxy S7 using Tapatalk
Any pictures ?
https://www.youtube.com/watch?v=KNgSDmkn96c
Every time I see this video I realize how good investment I did considering how easy is to work with.
@rbiter said:
Can't get a STD or phone pregnant.
Click to expand...
Click to collapse
Do you know what an analogy is? Lol
12MaNy said:
Do you know what an analogy is? Lol
Click to expand...
Click to collapse
Do you know what a joke is?

Anyone else already have a crack on the side where the antenna lines are?

My phone is about 14 days old. Already have a crack along the antenna line. love the phone otherwise and just want to know if anyone else has the issue. I always have it in a case.
Ksams said:
My phone is about 14 days old. Already have a crack along the antenna line. love the phone otherwise and just want to know if anyone else has the issue. I always have it in a case.
Click to expand...
Click to collapse
https://m.youtube.com/watch?reload=9&v=yyqNR6W_MUQ
Don't know what kind of case you have. I bought the tech 21 it's really rigid. I won't be sitting on this phone lol. In the video he use an awful lot of force I'd never put that kind of force on my phone.
wolfu11 said:
https://m.youtube.com/watch?reload=9&v=yyqNR6W_MUQ
Don't know what kind of case you have. I bought the tech 21 it's really rigid. I won't be sitting on this phone lol. In the video he use an awful lot of force I'd never put that kind of force on my phone.
Click to expand...
Click to collapse
I have a case that is more on the soft side but I haven't really done much to my phone besides put it in my pocket.
Wow that is so sad! I saw Jerry rigs strength test and it cracks during the bend test at 4 points where the antenna is. Oh god this phone is a nightmare then
Well.. send it it since you still have warranty?
Let's see how widespread an "issue" this is really going to be. I bet it won't be at all. [emoji1]
Sent from my Pixel 4 XL using Tapatalk
Ksams said:
I have a case that is more on the soft side but I haven't really done much to my phone besides put it in my pocket.
Click to expand...
Click to collapse
Was it your back pocket?
I smell a troll that saw a youtube video! LOL
I called support yesterday after reading the reports. Tier 1 rep went to Tier 2 to find out. He claimed that this would be covered by warranty barring other evidence of accidental damage - ie; fired from a cannon directly into a woodchipper. I guess I can't play hacky sack with the thing.
100rabh7791 said:
Wow that is so sad! I saw Jerry rigs strength test and it cracks during the bend test at 4 points where the antenna is. Oh god this phone is a nightmare then
Click to expand...
Click to collapse
Why exactly does that make this phone a nightmare? The pressure they put on this phone in the test is WAY more than anyone would typically put on it. Put it in your back pocket and sit down, probably, but that would likely be any phone. I've had a ton of different phones, and never, ever had one bend. Even my Blackberry pearl, EVO, or nexus s. Those were way before phones were very sturdy. I seriously doubt most folks will bend this phone.
gettinwicked said:
Why exactly does that make this phone a nightmare? The pressure they put on this phone in the test is WAY more than anyone would typically put on it. Put it in your back pocket and sit down, probably, but that would likely be any phone. I've had a ton of different phones, and never, ever had one bend. Even my Blackberry pearl, EVO, or nexus s. Those were way before phones were very sturdy. I seriously doubt most folks will bend this phone.
Click to expand...
Click to collapse
he forgot this wasn't a reddit post.
No cracks BUT I have official Google case for the xl (grey fabric) and just from taking it in/out of case some of the paint near the seam is coming off. WTF Google!!?? All black variant so I'm pretty pissed. Love the case but how the hell!? It's been in a case since minute 1 and never spent a second naked in my pocket or otherwise.
Ippolito1971 said:
No cracks BUT I have official Google case for the xl (grey fabric) and just from taking it in/out of case some of the paint near the seam is coming off. WTF Google!!?? All black variant so I'm pretty pissed. Love the case but how the hell!? It's been in a case since minute 1 and never spent a second naked in my pocket or otherwise.
Click to expand...
Click to collapse
Seems like it's a big F for the glossy finish for the black variant. You could try to warranty it out and see what happens.
Ippolito1971 said:
No cracks BUT I have official Google case for the xl (grey fabric) and just from taking it in/out of case some of the paint near the seam is coming off. WTF Google!!?? All black variant so I'm pretty pissed. Love the case but how the hell!? It's been in a case since minute 1 and never spent a second naked in my pocket or otherwise.
Click to expand...
Click to collapse
So as soon as you put it in the case this happened? Well it had to have since it was never outside a case for even a minute. But then you are taking it in and out of the case therefore it's been out for some time. I'm slightly confused as to if it's been out of a case or not. Nonetheless, I had a fabric case on my P3a and that thing is nearly impossible to get off. I did take it off once before the final time and it took me quite some time to get the phone out without damaging it. I'm not sure if the 4xl is the same but you definitely should get a replacement, put it in the case and leave it there.
I agree. I have the Pixel fabric case and find it impossible to take off. I find a good way is to take off the left side completely first. Don't try to take off from the top or bottom.
bobby janow said:
So as soon as you put it in the case this happened? Well it had to have since it was never outside a case for even a minute. But then you are taking it in and out of the case therefore it's been out for some time. I'm slightly confused as to if it's been out of a case or not. Nonetheless, I had a fabric case on my P3a and that thing is nearly impossible to get off. I did take it off once before the final time and it took me quite some time to get the phone out without damaging it. I'm not sure if the 4xl is the same but you definitely should get a replacement, put it in the case and leave it there.
Click to expand...
Click to collapse
Sure I take it out but it's never touched a surface and never been in my pocket without a case. Primarily using new Pixel 4XL case from Google. It's pretty upsetting.
Probably the taking in and out of the case that's doing it. The stock Google cases fit very tightly, something that holds true with the two aftermarket cases I've also purchased. None of them were easy to get the phone in and out of and were/are tighter than I expect from a case. I mean so far the thing I've done with my phone that is most likely to break a phone is putting it in the cases I've owned.
On the bendy thing I don't buy it at all; it's not just a significant force applied but also done so in a very particular way on the very tip of the ends with a fulcrum in the middle. Try and imagine how you will apply a similar loading to the frame in actual use and it isn't easy to come up with a scenario. Not saying they wont bend or cant be broken but I am saying that I would be very skeptical of anyone claiming they encountered this damage in normal use.
One last thought here is that I wonder or question where the bar is, how strong should the phone be? Obviously it should be able to stand up to the rigors of the day to day but are we starting to expect too much? I'm actually asking, not sure if I can define a realistic expectation for a phones strength. I do feel however that some people are asking too much from what with current technology is inherently going to be a somewhat fragile piece of electronic equipment.
One question did they ever have a bend test for flip phones? Short answer no! Why they would snap in half. I agree I think we are expecting these phones to be tanks.
Here is a better question. Who puts a 1,000 dollar device in their back pocket like it's a .25 cent pack of gum? ?
ZeroKool76 said:
Here is a better question. Who puts a 1,000 dollar device in their back pocket like it's a .25 cent pack of gum? ?
Click to expand...
Click to collapse
The real question is where are you finding packs of gum for 25¢?

Categories

Resources