Database Info

I sat on my Fuze :(

Hi all,
I sat on my Fuze, short and simple. There is now a weird crack on the screen. I am very familiar with what a broken LCD looks like, there is no LCD "liquid" oozing all over the place, and the picture is not distorted in any way. It looks like some kind of lens INSIDE might be broken, and I think it's the digitizer. The cracks stop once they get to the dark grey at&t/HTC border around the screen, even though I hit very close to it, so whatever I cracked is under the top lens/protector.
Also, I read online (albeit at a cell phone repair website) that you can't replace the digitizer without ruining the LCD. Is there any merit to this, or are they just trying to convince people to pay their obscene $149 to replace a $30 part?
So I guess I have two questions:
Did I break the digitizer, the topmost lens, or somehow the LCD glass without damaging the LCD itself?
How hard is this to replace?
Pics:
EDIT: I ordered this on April 17th. Fat chance AT&T will do anything about it, right?

That looks like just the digitizer... I purchased the digitizer already, but haven't gotten the chance to take it apart yet.... to be honest I'm very nervous about taking it apart.. I'm still trying to figure out how to split the two pieces apart (the keyboardbase and the slide screen....

wxy117 said:
That looks like just the digitizer... I purchased the digitizer already, but haven't gotten the chance to take it apart yet.... to be honest I'm very nervous about taking it apart.. I'm still trying to figure out how to split the two pieces apart (the keyboardbase and the slide screen....
Click to expand...
Click to collapse
If I'm not mistaken (and I might be), all this should take is removing the two small phillips head screws on the back of the screen that show when the phone is slid open. I landed on this thing while it was open, and drove my knee right into the screen, I'm surprised I didn't break anything else.

There are three more screws that you can't see behind the screen.... when its slid open you can only see 2 screws... There are actually 5

wxy117 said:
There are three more screws that you can't see behind the screen.... when its slid open you can only see 2 screws... There are actually 5
Click to expand...
Click to collapse
So we do have to take the whole damn thing apart?
Does anyone have any luck with AT&T replacing things that are clearly accidental damage? With all the horror stories I hear about refurbished phones and the chance that they might send me one, I'd actually rather take my chances at fixing this. I've taken apart a ton of phones and fixed them before, and worked at a cell phone repair shop for a few months. I still have most of my tools lying around, including all the screw drivers I'd need to open this.
I was able to find an HTC service manual that doesn't really explain how to replace the digitizer. It does describe how to get it in two pieces, but I wouldn't know where to go from there.

I have the digitizer in my hand... There is a thing that hooks up to the phone itself so yes i'm pretty sure you have to take apart the entire thing.... I think i'm gonna take the phone to NYC and have someone that knows what they're doing repair it. I tried to get warrenty repair, but they said no because it is accidental damage. i pretty much tried everything before I ordered a new screen.

wxy117 said:
I have the digitizer in my hand... There is a thing that hooks up to the phone itself so yes i'm pretty sure you have to take apart the entire thing.... I think i'm gonna take the phone to NYC and have someone that knows what they're doing repair it. I tried to get warrenty repair, but they said no because it is accidental damage. i pretty much tried everything before I ordered a new screen.
Click to expand...
Click to collapse
Found a good complete disassembly guide in Russian, why does the screen have to be the LAST thing to come out? I am now looking to buy an LCD/digitizer combo, but I can only find the one from Brando that is made for regular HTC Touch Pros, and not the Fuze (has a camera cutout instead of the AT&T logo).
If I end up having to replace the LCD I'd much rather break it trying to save $50 than just toss it. Is it really that hard to separate the digitizer from the LCD?
http://translate.google.com/transla...ka/htc-touch-pro/&sl=ru&tl=en&history_state0=

has anyone had success separating the Digitizer and the LCD screen?

wxy117 said:
has anyone had success separating the Digitizer and the LCD screen?
Click to expand...
Click to collapse
Well, we'll find out. I ordered both an AT&T Fuze digitizer by itself as well as an LCD with a digitizer attached. I'm just going to go ahead and replace everything with the combination unit and see if I can replace my broken digitizer without breaking my LCD in my free time. If it works, I have a spare or I can sell it

be careful I got my digitizer and they sent me the wrong one. They sent me one for a sprint touch pro....

wxy117 said:
be careful I got my digitizer and they sent me the wrong one. They sent me one for a sprint touch pro....
Click to expand...
Click to collapse
Hopefully I'll get it right, I made sure to order an AT&T Fuze digitizer that made it clear it wasn't for use with Sprint Touch Pros or Touch Pros with front facing camera.
The LCD+digitizer I ordered though may very well show up as any of the above, if they're not already attached I'm going to use the AT&T Fuze digitizer on the new LCD, and try and make a new working combo from my old LCD to resell. I'll make a detailed step by step with photos as well.

Don't forget to read this

They just sent out my new one today.... So anyone that needs a digitizer for the Fuze by Sprint hit me up.... They told me to keep it so now I have an extra digitizer that doesn't work for my phone...

I think I can help you cos I repaired LCD and digitizer on Raphael a week ago. Digitizer and LCD are two separate parts joined by flat printed wires. If you need to change just one of them you will need to take apart whole phone.
Raphael consists from 2 main parts - 1. that one with keyboard 2nd part with LCD. You have to take apart both what is quite hard to realize if you this for the first time.
Once you are with your LCD you will see the flat wires grom lcd and digitizer meerged. Split them with your solddering gun carefully! Take new digitizer and solder flat wires together. Anyway there is no glue or liquid fluit or whatever between digitizer and LCD. But - remeber especially those who replacing just LCD - there is kind of black tape around the backside of LCD part (the silver side) - take it apart from old lcd and move to new one. If you dont you will see the rainbow on your LCD but just after assembling whole device together - it is quite concerning if you find out this kinf of malfunction just after such a hard work like a assembling this hellmade device
Good luck to everyone!

pisqle said:
I think I can help you cos I repaired LCD and digitizer on Raphael a week ago. Digitizer and LCD are two separate parts joined by flat printed wires. If you need to change just one of them you will need to take apart whole phone.
Raphael consists from 2 main parts - 1. that one with keyboard 2nd part with LCD. You have to take apart both what is quite hard to realize if you this for the first time.
Once you are with your LCD you will see the flat wires grom lcd and digitizer meerged. Split them with your solddering gun carefully! Take new digitizer and solder flat wires together. Anyway there is no glue or liquid fluit or whatever between digitizer and LCD. But - remeber especially those who replacing just LCD - there is kind of black tape around the backside of LCD part (the silver side) - take it apart from old lcd and move to new one. If you dont you will see the rainbow on your LCD but just after assembling whole device together - it is quite concerning if you find out this kinf of malfunction just after such a hard work like a assembling this hellmade device
Good luck to everyone!
Click to expand...
Click to collapse
Thank you for some rather broken, but very helpful advice. Kinda sucks that I'm really happy since I don't have to worry about removing any adhesive, but now I have to sit here and solder flex cables. I shoulda bought a spare one
Do they ship these parts on pigeons from Hong Kong?

To anyone counting on being able to separate the LCD from the digitizer, DON'T. There is absolutely no way to separate them without destroying either or both. Also, take extreme caution when peeling up the flex cable, it is very easy to tear (I tore mine).
So my net cost, 80 + 50, LCD/Digitizer and Flex Cable = $130 vs. sending it to HTC $150. I advise anyone to just pay them rather than take this thing apart.

from my understanding people have done it before... Maybe you just had bad luck? Well we'll see when my screen comes in *crossing fingers*

wxy117 said:
from my understanding people have done it before... Maybe you just had bad luck? Well we'll see when my screen comes in *crossing fingers*
Click to expand...
Click to collapse
Fact of the matter is when people say this is a delicate phone to take apart, they mean it. I worked at a cell phone repair store for a few weeks, and learned how to take apart damn near anything (thank God this was before the iPhone existed). Not only are both flex cables in this phone taped down in 100 different places, making them very easy to tear while removing the tape, the adhesive used between the LCD and digitizer is STRONG. If you really wanted to separate them, you might have some luck with a straight edge and maybe an hour. Good luck, I'll let you all know how this turns out once I have my new flex cable, since I conveniently tore the volume buttons off the original.

I just got my screen today so we're gonna see some time next week how we do on this screen replacement....I'll let you know how it goes....

So far no luck with my digitizer. Has anyone had any luck just changing out the digitizer yet? The guy that was suppose to do mine is backing out because he doesn't want to risk cracking my LCD. I don't blame him thats the reason I didn't do it. sheik124 what are you doing with your damaged fuze? Are you sending it to HTC for repairs?

[GUIDE] I9000 Screen Replacement

This topic has clues for replacing the screen. I have not concluded an manual for chancing it yet but reading this whole topic gives you the big picture how it is done. Questions are always welcome and I try to answer them with my knowledge. This 1st post gives you 2 links to follow for pics about changing screen and my own starting point for chancing my own screen.
Has anyone bought and installed a digitizer+screen set which is on sale at ebay? I could not post direct link to ebay because I'm a newbie on these forums. You can find the product searching ebay with these keywords "I9000 digitizer". My galaxy's screen cracked and I need an replacement. Both screen and glass broke. I think that this set includes them both. There is also told in the questions that the set infact includes amoled display and not LCD as the title says.
Second question is that does someone have an service manual somewhere. Would be nice to know how to break apart my phone when replacing screen.
Third question is that doesn't samsung vibrant and galaxy s share the same chassis but different screen with more capacitive buttons. Could it be possible to install vibrant's screen to galaxy s?
PS. The way my galaxy brokedown is very funny. I lay down my phone on the kitchen table and the screen cracked. I was like OMFG when I heard the cracking noise. Phone was like 13 days old. Samsung does not repair it with warranty because they think that it wasn't an manufacturing defect. They said that I have dropped my phone and that's the way it broke. That could not be the case because I handled it like a baby. I would have to pay 255€ for new screen and digitizer. Hell no!! I'm a student so that sum does not fit with my wallet.
New screen installed, see posts http://forum.xda-developers.com/showpost.php?p=7683527&postcount=37 and http://forum.xda-developers.com/showpost.php?p=7710572&postcount=40
Edit: Ebay's prices have rised noticeable in the last couple of months. At the moment the price for these screens is around 100$. I found this site which sells them for 60£. http://www.shineyourmobile.co.uk/ProductDetails.aspx?pid=8128

pekkala89 said:
Second question is that does someone have an service manual somewhere. Would be nice to know how to break apart my phone when replacing screen.
Click to expand...
Click to collapse
There are 2 videos on the net, both on youtube I think. Just search "i9000 Disassembly" and you'll find one of them.
The Galaxy S has a serious design flaw as the glass goes around the home button (and the call ear/speaker) so it's very vulnerable there to shattering. I had my phone in the pocket and suddenly when I take it out I see it cracked right next to the home button. What had I done during the time it got cracked? The only possible explanation was carrying a _small_ speaker that then probably hit it. I was so surprised when I saw it cracked because even a speaker hit, when I lifted it up, is hard to consider cracking the screen.
So international model Galaxy S owners, be careful at the bottom and top of the screen. They're the weak points of the glass. For me only the glass cracked and not the screen so it will be interesting to see how much it will cost to fix.

Schmich said:
So international model Galaxy S owners, be careful at the bottom and top of the screen. They're the weak points of the glass. For me only the glass cracked and not the screen so it will be interesting to see how much it will cost to fix.
Click to expand...
Click to collapse
I think that you can't change only the glass. Amoled screen is so thin and I believe it's glued pretty thight to the glass. Separating them may be impossible without tearing the amoled.

the same...
i had a similar unfortunate event ... my screen cracked when i hit the phone to the metallic frame of a chair (it slipped out of my hand )...
it cracked exactly like you people said... near the home button.
i ordered the display + digitizer and i anxiously await its arrival to see if i can replace the damaged one.
it is quite tricky to dissassemble the display part but hope to succed...
keep you posted with the outcome
respect

pekkala89 said:
I think that you can't change only the glass. Amoled screen is so thin and I believe it's glued pretty thight to the glass. Separating them may be impossible without tearing the amoled.
Click to expand...
Click to collapse
Yeah that's my fear but I presume they just heat up the glue. That's how some industries do for other products. I think dental bracers (& its glue) have a different technique as well. So, will be interesting to see.

gallaxya said:
i ordered the display + digitizer and i anxiously await its arrival to see if i can replace the damaged one.
Click to expand...
Click to collapse
Where did you order it from?

If you were asked to pay more than $250 for screen replacement, then why don't you send it to Samsung in Korea? They will replace your SAMOLED for mere USD $100ish and ship it back to you for free (or may be not). This way you get a genium quality from original manufacturer and absolutely no hassles!

I dropped mine from around 4ft onto a concrete floor and its fine. Maybe I just got lucky.

Digitizer+Samoled set ordered from ebay. I should get it in two weeks. If possible I try to take pictures of the changing process and make an manual. I hope it's not glued tight to the chassis.

please do, i have some f***ing little scratches all over the screen, thought it was supposed to be scratch resistant.
Worst part is that it's in it's protective pouch all the time (maybe that's the probleme, dirt/dust might get trapped and rub against the screen).

Got my digitizer and amoled screen t
oday. I will report back if its a hard job or not to replace it.
Sent from my GT-I9000 using XDA App

yrizan said:
Got my digitizer and amoled screen t
oday. I will report back if its a hard job or not to replace it.
Sent from my GT-I9000 using XDA App
Click to expand...
Click to collapse
I tried to remove broken screen for 2 hours and no luck. Removing the motherboard is problematic because power button is glued to the chassis so I could only turn the motherboard aside and not remove it completely. I tried also to remove metal edge but I could only separate it from the left and right edge, not from top and bottom. I hope you have better luck and report how you managed to overcome my problems.

pekkala89 said:
I tried to remove broken screen for 2 hours and no luck. Removing the motherboard is problematic because power button is glued to the chassis so I could only turn the motherboard aside and not remove it completely. I tried also to remove metal edge but I could only separate it from the left and right edge, not from top and bottom. I hope you have better luck and report how you managed to overcome my problems.
Click to expand...
Click to collapse
Sorry to say got in to the same problems
Looks like the phone is build around the screen. Be careful with the metal ring, on top and bottom its between the screen and chassis, so if you brute force to much the screen cracks even more. The screen is glued to the chassis all around with superglue. I am not sure if its even possible to repalce the screen. It let me thinking that samsung wont repair broken galaxys , just replace them.
Ill keep working on the phone and keep trying, but compared to changing the screen on iphone is this like changing the screen on a iphone as a blind man without arms.
People thinking of buying this screen kit on eBay, don't do it. Just contact samsung for a repair.
Ill keep you posted.

I got the screen off.
No need to loosen the metaling ring around. The screen in dropped in the chassis from the front.
On the mainboard, just pop off the screen cable, long and flat next to the SD card slot.
The next step is very strange, just use brute force and crack the screen off the chassis, start from the top
When you get around the home button, be careful. Samsung has clued 2 sensors to the screen and chassis for back and option button. Best thing to do here is bend the screen back a little and cut loos the sensors from the digitizer with a sharp knife/scalpel. Samsung has used insane amount of clue on this phone.
Both the digitizer and amoled screen was clued to the chassis.
The next step is to clean off all the clue, buy loads of glue. Fill the chassis with glue and press the new screen on.
Wish me luck.
Ill keep you posted.

Making me a bit scared reading this thread, I`ve just bought phone Insurance just in case.Good luck fitting your replacement screens, sounds a bit daunting.

YES!!!
New screen in place and everything is working perfectly. Took about 3 hours first time (give or take). Its possible to do it a lot faster. The biggeste problem is the glue. Melting at about 120 celsius, but i was scared to heat the glas as i didnt know how much heat the mainbord could stand. All in all a pain in the a**, but doable.
I can also confirm this screen from ebay to be an orginal samsung amoled screen.
Best of luck too others trying a screen replace.
Sent from my GT-I9000 using XDA App

amoled or samoled though?

My mistake. Its a samoled screen
Sent from my GT-I9000 using XDA App

Awesome!!! thanks for the review
did you manage to snap a few pictures meanwhile you were working in your phone?

Im sorry, no pictures
The charger is missing to my canon camera, new one incomming from ebay. I'll post pictures next time ill change the screen ;-)
Sent from my GT-I9000 using XDA App

Eris cracked screen help

so i dropped my phone just the outer glass broke the lcd is find i was wondering where i can get the cheepest replacement for that i realy dont know what the price goes for but id rather not spend 500 on a retail andriod phone. my upgrade is like 3 months

Report it broken, pay $90 for a replacement through Asurion. Cheaper than $500, y'know?
Sent from my FroyoEris

You need to google for a eris digitizer.
LMGTFY
http://www.google.com/search?hl=en&...fai=CMBq5koWzTNrsN46EygTEha3rCQAAAKoEBU_Q0wbi

i think u can get them for like 40+ dollars off ebay

If you don't mind the long shipping times, you can get a digitizer + the entire housing together for around $60 on ebay. Doesn't seem like a bad deal to me.
#EDIT#
Zombie post . . . sorry about that. Need to remember to look at dates before replying.

Palmbxr said:
so i dropped my phone just the outer glass broke the lcd is find i was wondering where i can get the cheepest replacement for that i realy dont know what the price goes for but id rather not spend 500 on a retail andriod phone. my upgrade is like 3 months
Click to expand...
Click to collapse
I just replace mine, and is wasn't too bad. There is videos on YouTube about how to do it. It took me about an hour, and the part costs about 40 bucks. If you need any help with it, feel free to email me [email protected]
Aaron

you can get one @ 49usd
http://www.htcrepairparts.com/touch-screen-digitizer-for-htc-g5-eris-p-2727.html

Palmbxr said:
so i dropped my phone just the outer glass broke the lcd is find i was wondering where i can get the cheepest replacement for that i realy dont know what the price goes for but id rather not spend 500 on a retail andriod phone. my upgrade is like 3 months
Click to expand...
Click to collapse
I'm going through the same thing. Amazon has some digitizers for about $40. I decided to spend the extra $20 and get this instead
http://www.amazon.com/gp/product/B004F5CEDW
It's the whole casing. I didn't want to bother with stripping the digitzer off the frame which is glued on. With replacing the whole body, you just move the mainboard over and plug everything back in. At least this is my hope. I'll post here again when the thing actually arrives. I ordered it two weeks ago and it probably won't be here until mid March.
Good luck with whatever you decided to go with.
UPDATE. hmmm october was the post date. I guess this guy has long taken care of his problem

Are there any particular tools needed? I swear my other half is on a mission to destroy her phone. It'd be good to know how to do some of the possible DIY stuff.

roscuthiii said:
Are there any particular tools needed? I swear my other half is on a mission to destroy her phone. It'd be good to know how to do some of the possible DIY stuff.
Click to expand...
Click to collapse
There's Youtube videos for disassembly. I haven't watched them myself, but I know they exist, so they probably tell you what tools you need there. From what I remember hearing, just some small torx screwdrivers, or maybe some small phillips, too, but don't quote me on those.

Here is a link to the teardown video I followed.
http://www.youtube.com/watch?v=zHwm-32BI0w
The amazon link in my previous post is what I bought. It was the whole body. There are just screen replacements but I didn't want to mess with that because the digitizer is glued to the front piece. I didn't want to risk warping or breaking the front piece and completely screwing myself over. Anyway, what I bought came with the tools you need to perform the teardown and an extra screwdriver that was not needed.
I am glad I did this. However, it came with it's share of issues.
-The very top of my digitizer does not work. As a result, I can't pull down the notification bar. I can get to it through the menu button but it is annoying.
-I had to move the ear speaker and loudspeaker over. They were glued to some foam which was stuck/glued to the chassis. That foam absorbed the vibration. When my phone rings loud it is nasty because the speaker is bouncing around. I tried to cut some foam myself to replace what was stuck in the old case. It helped but it's not perfect.
-There are some rubber buffers? Isolators? Not sure what their called which also needed to be moved over form the old case.
-It took a month to ship to my house. After discovering these issues, I am kind've stuck with them because it would take a month to send the parts back and another month to get a replacement. By then I'll be due for a new phone.
So that's my experience of replacing the whole case.
Let me know if you have anymore questions.

Thanks for sharing your experience!

My pleasure. Glad to help out.
Sent from my Eris using XDA App

To add to this, because I'm sure there are others out there like me who intend to use their Eris until it gets run over, dropped in lava, drawn, quartered, and defecated upon . . .
I ordered the same replacement housing and digitizer as mentioned above, and had 2 small problems:
The housing I got had a nut in it that came loose, so that one of the corners wasn't able to reassemble properly.
There was something different in the new housing that caused the proximity sensor to function incorrectly.
For #1, I just used some super glue to weld the nut into place. This appears to have worked OK, but I fear that the point is weakened now and I will need to be very gentle if I disassemble the phone again.
For #2, The problem was that the housing was allowing bleed through inside the case from the proximity flasher to the light sensor, which caused the sensor to determine that there was something close to it when in fact there wasn't. I placed a small (oh so small) piece of electrical tape into the housing between where the IR flasher and sensor are located, and the problem was resolved.
If presented with the option of purchasing a new digitizer alone, or a new digitizer and housing together, follow groovel76's suggestion; it's well worth the time and money to go with the latter. The hassle of cleaning the old adhesive off of the new housing, and the risks of getting new adhesive in places where you don't want it far outweigh the cost of just getting a housing with adhesive pre-applied. I tried to do just a digitizer first, and ended up with a small amount of super glue (DO NOT RECOMMEND) getting on the new screen and the edge of the housing, as well as a screen that didn't seat properly because I didn't get quite all of the old bits out of the old housing. This resulted in dust getting under the screen and another crack when I attempted to fix what I'd screwed up the first time.
Between the availability of parts and ROMs for this phone, I see it being in my family for a LONG time yet.

Yes! Buy a digitizer online (most come with the tools you need such as the torx screwdrivers, mine did) and search for videos on youtube. That's what I did and it only cost me $37 for the digitizer and about 30 minutes of my time. And it worked perfectly as new when I got it all back together.

[Q] Repairing a damaged screen

First, the story:
I dropped my phone and broke the screen. The screen is always black now, but from the sounds the phone makes, it sounds like it is still working.
This place has instructions for replacing the touch screen digitizer and the LCD; they also sell these replacement parts (for $40 and $35 respectively), (I had to obfuscate the URL to post this, so replace the underscores with periods):
www_repairsuniverse_com/htc-mytouch-4g-slide-screen-repair-take-apart_html
I'm not quite ready to move on to a new phone yet, so I am planning on trying to fix this myself. I guess my other option is to see how much it would cost for TMobile to fix it for me, but I am guessing that they want too much. My phone is rooted (s-off) and running a Bulletproof 1.1 image.
Now, my questions:
Has anyone here successfully been through this process? Any advice would be greatly appreciated.
I have not yet attempted to disassemble the device to futher assess the damage, so I do not know exactly what is broken, although the glass is certainly broken, is this what is referred to as the "touch screen digitizer"?

LCD is the actual display. Digitizer is the glass that sits on top of the screen (the part you touch)
If your LCD is broken, the picture will be messed up

http://forum.xda-developers.com/showthread.php?t=1592219
Replaced the glass (digitizer) without issue. returned the phone to t-mo since prior to that it was having an issue with the hardware camera button being stuck always on. So long as you're patient, technical, and have a steady hand, do it, it's fine, just follow-the step-by-steps, and keep your screws and parts seperated at each step

I ordered a new LCD and digitizer, and will probably have some time to do the repair mid-late next week.
I went with the Sony version of the LCD based upon discussion in the following thread (in the 3rd post iynnoji says they tried a Hitachi LCD but it did not work):
http://forum.xda-developers.com/showthread.php?t=1526595
It would be nice to know if the Hitachi LCD is incompatible, or if iynnoji had a bad component or some other issue.
Anyway, thanks for the feedback gtmaster and eclipsed. I'll update this thread after I attempt the repair. I have to admit, I'm sort of glad I broke my phone, since learning to fix new things is such an enjoyable process. Hopefully I'm still happy about this process after I finish the repair and attempt to power the device on .

Yay! The repair was successful! Not having a cell phone really made me aware of how useful one is. Next time I upgrade I'll keep my old device around as a backup.
So some notes:
The screen assembly was really difficult to remove, due to the large amount of adhesive. When I took it off, the LCD split in two, with half attached to the screen assy and the other attached to the adhesive. Luckly I was intending on replacing the LCD anyway. Anyone else performing a screen or LCD repair should beware that this is a difficult step, and will take time and care.
The Sony LCD (P/N 60H00523) works fine with our device. As I previously mentioned, it would be nice to know if the Hitachi LCD (P/N 60H00512) works, as its $15 cheaper.
I wasn't careful enough when placing the LCD on the digitizer, and managed to a few dust particles sandwiched in there. Not a big deal, but if I were to do it again I'd check my work before assembling the rest of the phone.
I used the adhesive paper sold at repairs universe around the edges of the digitizer and put the phone in the oven @ 170 F for 5 minutes after assembly, then waited 10 minutes before using it. Everything seems solid.
Again, thanks all for the help.

Freerobots said:
Yay! The repair was successful! Not having a cell phone really made me aware of how useful one is. Next time I upgrade I'll keep my old device around as a backup.
So some notes:
The screen assembly was really difficult to remove, due to the large amount of adhesive. When I took it off, the LCD split in two, with half attached to the screen assy and the other attached to the adhesive. Luckly I was intending on replacing the LCD anyway. Anyone else performing a screen or LCD repair should beware that this is a difficult step, and will take time and care.
The Sony LCD (P/N 60H00523) works fine with our device. As I previously mentioned, it would be nice to know if the Hitachi LCD (P/N 60H00512) works, as its $15 cheaper.
I wasn't careful enough when placing the LCD on the digitizer, and managed to a few dust particles sandwiched in there. Not a big deal, but if I were to do it again I'd check my work before assembling the rest of the phone.
I used the adhesive paper sold at repairs universe around the edges of the digitizer and put the phone in the oven @ 170 F for 5 minutes after assembly, then waited 10 minutes before using it. Everything seems solid.
Again, thanks all for the help.
Click to expand...
Click to collapse
LCD splitting sounds messy I replaced my digitizer and there is loads of dust under it now. Gonna get it professionally done.
Sent from my Wildfire S A510e using xda app-developers app

Screen Crack and No Display

Hi all, Merry Christmas!
Well, my Christmas isnt so merry this year. Two families (friends with their kids) stopped by for Christmas eve dinner and my son with their kids were playing and the next thing i know, my tf300's screen cracked and no display. I can see the back light turned on, but no display. My TF300's alarm was beeping, so I am guessing that the tablet is still functional, but the screen is so messed up it wont show any display.
My question is, should I even attempt to fix the screen? Or just purchased a new one? I saw many cracked screen pics and all of them were able to turn their screen on.
Please advise on what to do.
Thanks,
Sid.

What's cracked? There 2 components in there: the LCD and the Digitizer. I assume if nothing shows then the LCD is gone, but that's a guess because if there's a crack across it normally would still show some (messed up) image like vertical or horizontal lines. Now the LCD is beneath the Digitizer. If you see cracks on the surface also, that means the Dig is gone too. Which makes it easier but costlier.
You can order both for around $150.00, but replacing can be a pain unless you've delicate hands. Separating the LCD from the digitizer is boring enough but you must to do this to get to the bezel. The more meticulous part is to remove the plastic bezel around the digitizer to reuse on the new one. You have to scrape around the edge because the two parts are initially bonded together by some really strong glue.
In my opinion, it's not worth it to take it to a shop as they would charge an inordinate amount for a used device (around $200.00!!). For the inept, it's certainly damn if you do and damn if you don't. If you need more info 'bout doing it, I can help as I've done it before. Alternatively, if you decide to get a new one and part this out, I am looking for the cable and possibly touchscreen board for mine. Maybe we can work something out. Whatever.

graphdarnell said:
What's cracked? There 2 components in there: the LCD and the Digitizer. I assume if nothing shows then the LCD is gone, but that's a guess because if there's a crack across it normally would still show some (messed up) image like vertical or horizontal lines. Now the LCD is beneath the Digitizer. If you see cracks on the surface also, that means the Dig is gone too. Which makes it easier but costlier.
You can order both for around $150.00, but replacing can be a pain unless you've delicate hands. Separating the LCD from the digitizer is boring enough but you must to do this to get to the bezel. The more meticulous part is to remove the plastic bezel around the digitizer to reuse on the new one. You have to scrape around the edge because the two parts are initially bonded together by some really strong glue.
In my opinion, it's not worth it to take it to a shop as they would charge an inordinate amount for a used device (around $200.00!!). For the inept, it's certainly damn if you do and damn if you don't. If you need more info 'bout doing it, I can help as I've done it before. Alternatively, if you decide to get a new one and part this out, I am looking for the cable and possibly touchscreen board for mine. Maybe we can work something out. Whatever.
Click to expand...
Click to collapse
I am not so sure what's cracked actually. But, if i press the power button, there's just black screen, no display whatsoever although i can see light shines through the cracks. So I am guessing both the LCD and the Dig are gone.
I am thinking about parting the broken one out and buy a refurbished one from walmart and get the walmart protection plan, so I dont have to worry about a broken tablet for at least 2 years.