Stuck at ASUS logo - Transformer TF300T Q&A, Help & Troubleshooting

I have unlocked my bootloader using the Asus tool. I was following Step #3 from the link below. Everything went fine as I was able to boot back into stock JB and download SuperSu, apply the update and get root. I downloaded Root Checker and verified that I had root.
http://forum.xda-developers.com/showthread.php?t=1845377
I then downloaded CM 10 and ASU JellyBean Hydro R1 and tried to flash each one of them. I always wipe everything before flashing and fix permissions after flashing. When I reboot, it just hangs at the ASUS boot screen. Any ideas? I have tried flashing from both CWM and TWRP with the same results.
Any ideas or help would be greatly appreciated.

1st if you went to stock JB there is no way of flashing CM10, Skang JB, Blackbean and all other ICs roms.
Only thing you should be able to flash is Hydro JB or stock JB. You have to use the JB recovery from now on. I would recommand TWRP for JB.
If you have this, just follow the instructions in the HydroJB thread. After flashing the Hydro Rom you have to boot into system once. After that you can go back to recovery and flash the Hydro Update.

Thanks for the reply mikaole. I tried flashing the Hydro JB rom and even the stock JB rom from Asus's site. Hydro just stops at the Asus logo after flashing. Stock JB does the same thing, but it displays "md5 mismatch" in red underneath "device is unlocked", then stops at Asus logo. I am going to try to download the stock JB rom again from Asus and see if I just had a bad download. I will try going back to TWRP instead of CWM too. Is there a specific version of TWRP that I should use? I used the one's in step #3 of the thread I referenced in the OP. I appreciate any help or advice.

I was able to flash back to TWRP JB recovery, then download a fresh copy of the stock Asus JB rom, wipe everything, flash the rom, fix permission and reboot and this time it worked. I think the only thing I really did different this time was to fix permissions after flashing.
Thanks again!

work for me! tanks DAVID!!

The same problem
Hi at all, i'm writing from italy so my english is not so good
i've the same problem with my TF300t: i've update my tab to JB with OTA and then unlock the BL with asus apk. then i've rooted my tab and all works fine.
But then i've tried to mount the CM10 rom, and after the installation my tab stuck at bootlogo
i've read to try to install hydro JB or asus stock rom, but my PC now do not read the device (tf300t): so how can i install another rom if my tab can't load nothing via USB?
thanks for the replies, Jacopo

IlCamo said:
i've read to try to install hydro JB or asus stock rom, but my PC now do not read the device (tf300t): so how can i install another rom if my tab can't load nothing via USB?
Click to expand...
Click to collapse
Try using different USB ports on your PC.

davidboyd said:
Try using different USB ports on your PC.
Click to expand...
Click to collapse
alredy tried, but nothing change. now i'm trying to go into APX mode to let PC read tab, but my PC doesn't intall the driver.
I've found that here http://forum.xda-developers.com/showthread.php?t=1426502, i hope that is the better way
EDIT: i've install APX driver but my PC won't read the tab.
where can i find transformer's driver?

IlCamo said:
where can i find transformer's driver?
Click to expand...
Click to collapse
Install Asus Sync. If you already have it installed, uninstall it, reboot and reinstall it.

IlCamo said:
alredy tried, but nothing change. now i'm trying to go into APX mode to let PC read tab, but my PC doesn't intall the driver.
I've found that here http://forum.xda-developers.com/showthread.php?t=1426502, i hope that is the better way
EDIT: i've install APX driver but my PC won't read the tab.
where can i find transformer's driver?
Click to expand...
Click to collapse
same problem with you, and I installed dirvers you metioned successfully, but when i used wheelie commond, it said " failed to read data from blob",
maybe because i used tf201's blob, and i can't find tf300 nvflash roms, any ideas?

IlCamo said:
Hi at all, i'm writing from italy so my english is not so good
i've the same problem with my TF300t: i've update my tab to JB with OTA and then unlock the BL with asus apk. then i've rooted my tab and all works fine.
But then i've tried to mount the CM10 rom, and after the installation my tab stuck at bootlogo
i've read to try to install hydro JB or asus stock rom, but my PC now do not read the device (tf300t): so how can i install another rom if my tab can't load nothing via USB?
thanks for the replies, Jacopo
Click to expand...
Click to collapse
Did you make a nandroid backup before flashing cm10? If so, just restore from there and you should be able to sync from your pc

davidboyd said:
Install Asus Sync. If you already have it installed, uninstall it, reboot and reinstall it.
Click to expand...
Click to collapse
done, but already nothing change.
babymatteo said:
Did you make a nandroid backup before flashing cm10? If so, just restore from there and you should be able to sync from your pc
Click to expand...
Click to collapse
i have not do a nandroid backup.
why my pc doesn't read the tab when i install apx driver ? i'm workin' on W7 OS, and when i put the USB cable into my tf300t i hear a sound of connection, but the device not appear in the listview of computer.
PS: thanks to everybody for suggestions guys

IlCamo said:
Hi at all, i'm writing from italy so my english is not so good
i've the same problem with my TF300t: i've update my tab to JB with OTA and then unlock the BL with asus apk. then i've rooted my tab and all works fine.
But then i've tried to mount the CM10 rom, and after the installation my tab stuck at bootlogo
i've read to try to install hydro JB or asus stock rom, but my PC now do not read the device (tf300t): so how can i install another rom if my tab can't load nothing via USB?
thanks for the replies, Jacopo
Click to expand...
Click to collapse
Hi!
If fastboot work , you can re-flash official stock JB ! ( put your device in fastboot mode and see if fastboot comand respond ..) ! Good luck ! :good:
to try if it work just type > fastboot -i 0x0B05 reboot

surdu_petru said:
Hi!
If fastboot work , you can re-flash official stock JB ! ( put your device in fastboot mode and see if fastboot comand respond ..) ! Good luck ! :good:
to try if it work just type > fastboot -i 0x0B05 reboot
Click to expand...
Click to collapse
thanks for the support man
i have a question: what stock FW i must to download from asus website?
ww sku, tw sku or us sku FW? my tab is an european tab (buy in italy)

IlCamo said:
thanks for the support man
i have a question: what stock FW i must to download from asus website?
ww sku, tw sku or us sku FW? my tab is an european tab (buy in italy)
Click to expand...
Click to collapse
Hi !
I use WW SKU and work great ....I think is for european version ....but I'm not 100% sure ! :good:

surdu_petru said:
Hi!
If fastboot work , you can re-flash official stock JB ! ( put your device in fastboot mode and see if fastboot comand respond ..) ! Good luck ! :good:
to try if it work just type > fastboot -i 0x0B05 reboot
Click to expand...
Click to collapse
surdu_petru said:
Hi !
I use WW SKU and work great ....I think is for european version ....but I'm not 100% sure ! :good:
Click to expand...
Click to collapse
in download
now i'm trying to install HyDro JB rom after all wipe, i have downloaded it from here, put it into EX SD and then with TWRP recovery put into internal sd card. So now i can install also the stock rom if HyDro JB doesn't work!
Yeah :laugh:
maybe doesn't work, but all i have download i can put into the tf300t's storage

IlCamo said:
in download
now i'm trying to install HyDro JB rom after all wipe, i have downloaded it from here, put it into EX SD and then with TWRP recovery put into internal sd card. So now i can install also the stock rom if HyDro JB doesn't work!
Yeah :laugh:
maybe doesn't work, but all i have download i can put into the tf300t's storage
Click to expand...
Click to collapse
So , TWRP work in your device now ? ....

surdu_petru said:
So , TWRP work in your device now ? ....
Click to expand...
Click to collapse
TWRP work ever! but i haven't use an EX SD card into the tab, it's first time that i use for it.
But HyDro JB don't work, and TWRP doesn't flash the stock FW.

IlCamo said:
TWRP work ever! but i haven't use an EX SD card into the tab, it's first time that i use for it.
But HyDro JB don't work, and TWRP doesn't flash the stock FW.
Click to expand...
Click to collapse
Hi !
than you can try to flash blob files into firmware.zip directly in fastboot mode ! ...of course if fastboot command it work ...
what TWRP you use :2.2.1.5 or 2.2.2.0 ? - I use 2.2.2.0 and I can flash asus firmware JB !
...another thing ( I'm not sure 100% ) you must to unzip firmware.zip because is double zipped ! I downloaded the WW SKU.zip unzipped this archive and I get another archive .zip ! so you need to put in sdcard the second archive !
...also if fastboot work , put your device in fastboot mode and > fastboot -i 0x0B05 flash staging blob
( where blob~818MB is in firmware asus JB archive ! )

surdu_petru said:
So , TWRP work in your device now ? ....
Click to expand...
Click to collapse
surdu_petru said:
Hi !
than you can try to flash blob files into firmware.zip directly in fastboot mode ! ...of course if fastboot command it work ...
what TWRP you use :2.2.1.5 or 2.2.2.0 ? - I use 2.2.2.0 and I can flash asus firmware JB !
...another thing ( I'm not sure 100% ) you must to unzip firmware.zip because is double zipped ! I downloaded the WW SKU.zip unzipped this archive and I get another archive .zip ! so you need to put in sdcard the second archive !
...also if fastboot work , put your device in fastboot mode and > fastboot -i 0x0B05 flash staging blob
( where blob~818MB is in firmware asus JB archive ! )
Click to expand...
Click to collapse
Wait, a lot of questions
So..TWRP 2.2.1.5, the zip of stock FW is double zipped (thanks, i haven't see that).
but..what is blob files? sorry for my ignorance
i can't use fastboot mode because i can't connect my tab with the pc via usb cable. if i have understand what you says

Related

Might have bricked my device :/

Hey,first post on the forums and first problem,today i felt like unlocking my 300tg and i did,it was flawless;unlocked from the asus bootlocker apk,then flashed a twrp recovery from the terminal emulator.Then,i downloaded the hydro rom and put it in my storage,cleaned catches and dalvik and tried to install the zip then it went nuts.First the recovery said "error flasing" ,then i tried flashing some other roms and now the recovery tries to flash it and just restarts.What could be the problem here?
Thanks in advance.
sin5k4 said:
Hey,first post on the forums and first problem,today i felt like unlocking my 300tg and i did,it was flawless;unlocked from the asus bootlocker apk,then flashed a twrp recovery from the terminal emulator.Then,i downloaded the hydro rom and put it in my storage,cleaned catches and dalvik and tried to install the zip then it went nuts.First the recovery said "error flasing" ,then i tried flashing some other roms and now the recovery tries to flash it and just restarts.What could be the problem here?
Thanks in advance.
Click to expand...
Click to collapse
Hi!
You must to install Rom for your device not for TF300T ! ....seems to be here problem !
surdu_petru said:
Hi!
You must to install Rom for your device not for TF300T ! ....seems to be here problem !
Click to expand...
Click to collapse
Well, it was the TG version of Hydro but did not work for some reason.Anyway had access to fastboot so i simply flashed the original blob from Asus' website.Lost the bootlocker for no reason tho

[A700] [HowTo] Update German Version to JB

Hi!
Just found a way to update to JB from the 1.053 version (Acer_AV043_A700_RV22RC03_EMEA_DE) on wich every other update failed for me. But runs with the other versions, too.
Unlock Bootloader
Install CWM (6.0.1.4)
Visit this german forum
get the file A700 JB Full ROM AV051_1.028.00_EMEA_DE RV09RC02.zip
flash it via CWM
DONE!
Just tested and it's working.
Credits go to those who deserve it.
I deleted CWM and a mate let it where it was and both A700 are running fine [*] (see below!)
... now waiting for root
----------------------------
[*] New info:
My friend, who kept CWM, unlocked the bootloader again after the update and now has a bootloop. So my advice is to kill CWM after the update.
I don't get into recovery too (with locked bootloader) it says "recovery image verified failed". But system starts normally afterwards.
------------------
More info:
I had CWM on the tab too, because i misunderstood the question:
When asked
Code:
ROM may flash stock recovery on boot. Fix?
No
No
No
Yes - Disable recovery flash
say NO! to kill CWM.
------------------
Still more info to come:
(4.10.2012)
The bootloop was fixed by flashing a propriate recovery after beeing able to enter fastboot using the right key combination.
andiby left us a JB stock recovery: recovery.img and he build a CWM 6.0.1.4 with JB Kernel: recovery-a700-6014JB.img which runs fine for me.
Use the CWM with JB Kernel only to flash files and not to WIPE, FORMAT or RESTORE a backup, because there were issues with a different JB based CWM and I can't guarantee this one to work, because I have not tested it.
I'm on FR Firmware, can you tell me how should I proceed?
If you want to keep the FR firmware you will have to wait for an appropriate update file.
If you want to switch to Germen I think it should work with this method, because the zip file contains everything from bootloader to system files.
Do you think I can here: https://app.dumptruck.goldenfrog.com/p/GOKKb2PavJ download an install then install Acer_A700_AV043.RV07RC03_AV043.RV07RC06_EMEA_DE thereafter this here JB?
I would not recommend it, because your file is only 340 MB while the one from the thread above is nearly 400 MB.
I think you only need the file from my post, because there is everything in it fpr JB afaik, but I can give no guarantee, because I only used it to update my German version.
PS: Might it be posible to reduce the size of your signature a bit? Threads are much more difficult to read if a signature is almost always larger than a normal post. Thank you to give consideration to my request.
DЯΦ[email protected]П said:
I would not recommend it, because your file is only 340 MB while the one from the thread above is nearly 400 MB.
PS: Might it be posible to reduce the size of your signature a bit? Threads are much more difficult to read if a signature is almost always larger than a normal post. Thank you to give consideration to my wish.
Click to expand...
Click to collapse
Yes but i can from FR Firmware to DE and install first update (5MB) and this is 1.053 => finally JB or i think wrong?
PS: Nope. These are my projects
update or flash total
Is it an upgrade or full flash?
Did you delete all data you had or upgrade your system?
elunico32 said:
Is it an upgrade or full flash?
Did you delete all data you had or upgrade your system?
Click to expand...
Click to collapse
It's an update. Everything is on the tab as before.
@DakiX: all I can say is that I would not recommend using this method with any other file than the one mentioned in the first post, because this is the one I tested.
Thank
Thank you. I will flash now.
DЯΦ[email protected]П said:
@DakiX: all I can say is that I would not recommend using this method with any other file than the one mentioned in the first post, because this is the one I tested.
Click to expand...
Click to collapse
You don't understand me what i mean. I will flash the DE Firmware afterthat 1.053 und then the JB!
Are you from germany?
DakiX said:
You don't understand me what i mean.
Click to expand...
Click to collapse
Maybe ...
I will flash the DE Firmware afterthat 1.053 und then the JB!
Click to expand...
Click to collapse
I just don't get why you want to flash anything else before the "A700 JB Full ROM AV051_1.028.00_EMEA_DE RV09RC02.zip" because it is a FULL ROM and should be flashable over ICS 1.023, ICS 1.027, ICS 1.053 and ICS 1.055 to get JB 1.028.
Are you from germany?
Click to expand...
Click to collapse
My flag says: yes
You have a PM
Works great ! Thanks !
But for me, recovery 6.0.1.4 is KO after the update. I need to use the one with "the brick bug". Not good at all
I will wait for Pawitp before using it...
ROM may flash stock recovery on boot. Fix?
No
No
No
Yes - Disable recovery flash
Yes or no?
DakiX said:
ROM may flash stock recovery on boot. Fix?
No
No
No
Yes - Disable recovery flash
Yes or no?
Click to expand...
Click to collapse
I disabled it, then CWM is away and the Tab as stock as possible.
A friend kept CWM and now has some issues...
HOLY *%/***** i had FR Firmware and i do this:
download jb
move to sd
unlock bootloader
root with patched-boot
flash cwm
reboot to recovery
install jb..
yes disable recovery..
reboot system now & FINALLY JELLY BEAN :good: oh my... its very fast + smooth and equal to another tablet!
I hate to root and flash 10 inch tablets - i'm am smartphone fetishist
DakiX said:
HOLY *%/***** i had FR Firmware and i do this:
download jb
move to sd
unlock bootloader
root with patched-boot
flash cwm
reboot to recovery
install jb..
yes disable recovery..
reboot system now & FINALLY JELLY BEAN :good: oh my... its very fast + smooth and equal to another tablet!
I hate to root and flash 10 inch tablets - i'm am smartphone fetishist
Click to expand...
Click to collapse
Can you get into recovery mode using "adb reboot recovery"?
Nope.. failed but its understandable because CWM must be made for 4.1.1
DakiX said:
Nope.. failed but its understandable because CWM must be made for 4.1.1
Click to expand...
Click to collapse
But you kicked CWM and should have stock recovery now. Thats what you did by sayin "yes" or am i completely wrong?
DЯΦ[email protected]П said:
But you kicked CWM and should have stock recovery now. Thats what you did by sayin "yes" or am i completely wrong?
Click to expand...
Click to collapse
Yes i disable it. I can in stock recovery but CWM is gone^^ that i mean :highfive:

[Q] howto new boolloader

Hi all
new to this...so probably a stupid question !!!
I'm using a TF300TG with bootloader WW_v10.6.2.10.
On asus site, I see a booloader upgrade WW_v10.6.2.11 which is a zip file
How do I do the upgrade ?
Installing the zip within TWRP or else
thks in advance for clarification
zorglub! said:
Hi all
new to this...so probably a stupid question !!!
I'm using a TF300TG with bootloader WW_v10.6.2.10.
On asus site, I see a booloader upgrade WW_v10.6.2.11 which is a zip file
How do I do the upgrade ?
Installing the zip within TWRP or else
thks in advance for clarification
Click to expand...
Click to collapse
I'm not familiar with TF300tg bootloader versions, but I would recommend flashing the new stock via Fastboot so you can confirm it is working to reinstall TWRP.
cmendonc2 said:
I'm not familiar with TF300tg bootloader versions, but I would recommend flashing the new stock via Fastboot so you can confirm it is working to reinstall TWRP.
Click to expand...
Click to collapse
HI
Thks for yr suggestion
I have discovered another way to solve my problem without the need to reisntall stock rom
you simply need to put the bootloader zip file on top of an external SD.
Boot yr TG and hotplug the SD.
As soon yr SD is detected, there is a notification message saying an update file is sitting there... clicking on it launches the update process....:laugh:
This method works with any firmware update

[q] asus padfone 2 (unrooted ) jelly bean 4.1 stock on asus boot logo ( help please

HI I NEED YOUR HELP PLEASE : I HAVE ASUS PADFONE 2 suddenly WHEN I WAS SEARCHING ON GOOGLE ITS SHOW ME ( unfortunately google app has stopped ) AND STOCK THERE SO I DID RESET AFTER THAT THE PHONE ITS STOCK ON BOOTING UP ASUS LOGO AND AFTER 15 MINT ITS PASS THE BOOT LOGO AND ITS SHOW ME ON THE TOP ( ENCRYPTION UNSUCCESSFUL ) AND ON THE BOTTOM ( RESET PHONE ) BUT WHEN I HIT ON RESET PHONE IT DOES NOT DOING ANYTHING THE PHONE ITS ( UNROOTED ) AND IT WAS RUNNING ANDROID JELLY JEAN ( 4.1) AND I CAN GET INTO STOCK RECOVERY AND I DID WIPE DATA/ FACTORY RESET AND WIPE CACHE PARTITION BUT STILL STOCK ON BOOT LOGO AND NOT BOOTING NORMALLY AFTER I USED ( ADB BOOT LOADER ) AND TRIED TO FLASH A NEW FIRMWARE BY USING ( CWM RECOVERY ) I DIDNT FLASH THE CWM RECOVERY JUST USED THE IMG RECOVERY TO FLASH THE FIRMWARE ( INSTALL ZIP FROM SIDELOAD ) AND I SENT THE FIRMWARE TO MY PHONE BUT THE CWM RECOVERY COULDN'T FLASH IT ( UNSUCCESSFUL ) BECAUSE CWM RECOVERY ITS GAVE ME EVERY TIME ( E: CANT MOUNT ) ANYTHING I DID WITH CWM RECOVERY IT DOES NOT WORK SO I NEED YOUR HELP GUYS PLEASE ANYBODY CAN HELP ME WITH THAT I WILL BE APPRECIATED AND THANK YOU PLEASE HELP NOTE : I DONT KNOW WHAT IS THE BUILD NUMBER ON MY PHONE BUT I BOUGHT IT FROM TAIWAN .... HEY GUYS CHECK THE PICS PLEASE WHICH I POSTED AND THANKS
What for a ROM and CWM Version have you using?
CWM6.0.2.9 goes not for the most ROMs! You must need CWM6.0.4.4 or higher, or TWRP-Recovery for Padfone 2!
Perhabs your Device can reactivatet by a new Firmware-Flash with CWM6.0.4.4 or TWRP!
Thank you so much for your replies
roselanguste said:
What for a ROM and CWM Version have you using?
CWM6.0.2.9 goes not for the most ROMs! You must need CWM6.0.4.4 or higher, or TWRP-Recovery for Padfone 2!
Perhabs your Device can reactivatet by a new Firmware-Flash with CWM6.0.4.4 or TWRP!
Click to expand...
Click to collapse
YES I WAS USED CWM:6.0.2.9 I TRIED OVER 20 TIMES WITHOUT ANY SUCCEED (UNSUCCESSFUL) AS SHOWN IN THE PICTURES WHICH I POSTED ALREADY I TRIED ALL THESE ROMS : TW_A68-11.8.4.12-0-ota-user.zip ,TW_A68-11.8.4.6-0-ota-user.zip,WW_A68-11.8.4.23-0-ota-user.zip,CHT_A68-11.8.3.3-0-ota-user.zip,CN_A68-10.4.17.7-0-ota-user.zip,HK_A68-10.4.17.7-0-ota-user.zip,TW_A68-11.8.4.23-0-ota-user.zip ,,, I TRIED ALL THESE ROMS BECAUSE I DONT KNOW WHAT IT WAS MY ( BUILD NUMBER ) I CANT REMEMBER I JUST KNOW IT WAS JELLY BEAN 4.1 AND MY PADFONE 2 MODEL A68 IT WAS NOT ROOTED IT HAS STUCK FIRMWARE AND HAS ( LOCKED BOOTLOADER ) AND I TRIED TOO : adb push firmware.zip /data/media for example :adb push TW_A68-11.8.4.23-0-ota-user.zip /data/media and i pushed already to my external storage because there is no memory card on this phone (sdcard) using the stock recovery and when i tried to install the update from the /data/media it shows : install update and after 15 mint it gave me installation aborted and i wanna tell you something else the CWM RECOVERY WHEN I USED IT I DIDNT FLASH IT I JUST BOOT LIKE TESTED :fastboot boot recover.img because i dont know if i can flash it or not because my phone its ( not rooted ) please i need your help and thank you so much and if you need more information just let me know because maybe i forgot something just let me know and thanks
false national rom!
I think you have Flash the fals national Rom! TW = Taiwan-ROM, CHT = China-ROM, WW = Worldwide-English, and so on! Thats named SKU Version of the ROM! When your padfone from Europa or USA than you need a WW or WWE ROM! It gives a thread on XDA for flashing other,false,back SKU on Padfones! Search that thread, there a tuturials for Changing or Flash back SKUs! Your device need a Flash back to his original SKU-Version of your ROM!
And for CWM your padfone must be unlocked! But thats simple! On Asus Homepage search your device, and than you can Download a Unlock-APK! Download and install thies apk on your padfone, and start it, than your bootloader is unlocked! And after that, you can install CWM or TWRP on several ways!
roselanguste said:
I think you have Flash the fals national Rom! TW = Taiwan-ROM, CHT = China-ROM, WW = Worldwide-English, and so on! Thats named SKU Version of the ROM! When your padfone from Europa or USA than you need a WW or WWE ROM! It gives a thread on XDA for flashing other,false,back SKU on Padfones! Search that thread, there a tuturials for Changing or Flash back SKUs! Your device need a Flash back to his original SKU-Version of your ROM!
And for CWM your padfone must be unlocked! But thats simple! On Asus Homepage search your device, and than you can Download a Unlock-APK! Download and install thies apk on your padfone, and start it, than your bootloader is unlocked! And after that, you can install CWM or TWRP on several ways!
Click to expand...
Click to collapse
i dont know what is the fals natinoal rom ? and i bought my phone from taiwan ? and i dont know what is my build version i cant remember ? and how i can unlock the bootloader and my phone its not booting up normally ? can you tell me what i have to do please step by step and thank you so much
Build-Number is not important!
May be i can help you! Can you start the device in CWM-Mode? Can you go in CWM? In case that you can, load a TW-ROM (TW=Taiwan) via ADB-Sideload over CWM to your device! Than the device should install the original TW-ROM automaticaly!
In case that CWM not Functional, try to turn off the device, wait 30-seconds, than hold the ``+`` (Plus) button on the side of the device, and turn on the device where you hold the ``+`` (Plus) button permanently! Yet should come the ASUS-Logo and in the Top of the Display should stand ``Fastboot-Mode``! Can you please try that, and say me what the device do!?
roselanguste said:
Build-Number is not important!
May be i can help you! Can you start the device in CWM-Mode? Can you go in CWM? In case that you can, load a TW-ROM (TW=Taiwan) via ADB-Sideload over CWM to your device! Than the device should install the original TW-ROM automaticaly!
In case that CWM not Functional, try to turn off the device, wait 30-seconds, than hold the ``+`` (Plus) button on the side of the device, and turn on the device where you hold the ``+`` (Plus) button permanently! Yet should come the ASUS-Logo and in the Top of the Display should stand ``Fastboot-Mode``! Can you please try that, and say me what the device do!?
Click to expand...
Click to collapse
I TRIED ALL THE TW : ROMS WHICH I SENT IT TO YOU ALREADY ABOVE AND I DOWNLOAD THESE ROMS FROM ASUS WEBSITE FIRMWARES ,, AND I SENT THE ROMS USING THE SIDELOAD TO MY PHONE AND IM NOT FLASHING THE CWM ON MY PHONE BECUSE MY PHONE ITS NOT ROOTED AND THE BOOTLOADER ITS LOCKED I JUST LET CWM TO BOOT ON MY PHONE NOT FLASH IT AND WHEN I TRIED TO INSTALL THE UPDATE USING CWM ITS GAVE ME ( INSTALLATION ABORTED ) STATUS 7 ERROR ,,,, check the pics please and thanks
Ok! I think it is the old CWM6.0.2.9 problem, this version of CWM has problems with flashing ROMs! BUT, there is one ROM on XDA for Padfone2 that must flash with CWM6.0.2.9! It is Tari's Padfone2 Custom ROM+Kernel! It is easy to find on XDA, and this ROM will flashing over Sideload with CWM6.0.2.9! Search on XDA for Tari's Padfone2 ROM, there you can Download the files, and there is also a step by step tuturial, follow that, and try!
And have you tested that Fastboot goes?
roselanguste said:
Ok! I think it is the old CWM6.0.2.9 problem, this version of CWM has problems with flashing ROMs! BUT, there is one ROM on XDA for Padfone2 that must flash with CWM6.0.2.9! It is Tari's Padfone2 Custom ROM+Kernel! It is easy to find on XDA, and this ROM will flashing over Sideload with CWM6.0.2.9! Search on XDA for Tari's Padfone2 ROM, there you can Download the files, and there is also a step by step tuturial, follow that, and try!
And have you tested that Fastboot goes?
Click to expand...
Click to collapse
yes i used cwm 6.0.29 ,, ok but you said taris padfone 2 rom its custom rom how am gonna flash it and my phone its not rooted and the bootloader on my phone its locked
wasim74 said:
yes i used cwm 6.0.29 ,, ok but you said taris padfone 2 rom its custom rom how am gonna flash it and my phone its not rooted and the bootloader on my phone its locked
Click to expand...
Click to collapse
yes i tried fastboot and sideload i have no problem with that i can send the roms to my phone but the problem my phone cant flash it ?
OK! But i think your Bootloader is Open, than otherwise, you cant go in Fastbootmode or CWM!? Fastbootmode and CWM (Recovery), that is the Bootloader!
You can go in CWM, then you can make the flash-prozedure of all ROMs! (Stock and Custom)!
Try Taris ROM! Go in CWM, make Wipe Data/Factory Reset, make Wipe Cache, and Sideload Taris ROM!
Did that not work, try CWM6.0.4.4 or TWRP-Recovery to Flash Original ASUS-TW-Firmware!
And when you can start CWM with - fastboot boot recovery.img - , than normaly you can also Flash it permanently with - fastboot flash recovery recovery.img - !
roselanguste said:
OK! But i think your Bootloader is Open, than otherwise, you cant go in Fastbootmode or CWM!? Fastbootmode and CWM (Recovery), that is the Bootloader!
You can go in CWM, then you can make the flash-prozedure of all ROMs! (Stock and Custom)!
Try Taris ROM! Go in CWM, make Wipe Data/Factory Reset, make Wipe Cache, and Sideload Taris ROM!
Did that not work, try CWM6.0.4.4 or TWRP-Recovery to Flash Original ASUS-TW-Firmware!
And when you can start CWM with - fastboot boot recovery.img - , than normaly you can also Flash it permanently with - fastboot flash recovery recovery.img - !
Click to expand...
Click to collapse
but i didnt unlock the bootloader on my phone how come its unlock i dont know ? so you mean i have to flash the cwm on my phone after that send one of the TW-ROMS to my phone and flash it too ,,, ok i will try that but from where i can get the cwm6.0.4.4 for padfone2 let me know please and thank you so much because you are help me with that ?
wasim74 said:
but i didnt unlock the bootloader on my phone how come its unlock i dont know ? so you mean i have to flash the cwm on my phone after that send one of the TW-ROMS to my phone and flash it too ,,, ok i will try that but from where i can get the cwm6.0.4.4 for padfone2 let me know please and thank you so much because you are help me with that ?
Click to expand...
Click to collapse
oh ,, just to let you know when i used the cwm 6.0.2.9 i cant do wipe -factory reset or wipe cashe its gave me e: cnt mount but on stock recovery i can do wipe cashe and factory reset but it take too long to do that
There is a other custom ROM for Padfone2 from Sissidroid! Search on XDA for - Guerilla ROM - it is easy to find, and in the thread to this ROM there is a link for Download CWM6.0.4.4. Because CWM6.0.4.4 is needed to Flash Guerilla-ROM from Sissidroid!
In Google search - TWRP for Padfone2 - then you find a TWRP-Site, from there you can Download TWRP-Recoverys for Padfone2. Take the Version 2.6.3.0 of TWRP, not other. The other Versions dont go! TWRP is a Recovery like CWM, but TWRP has a Touch-Interface, and the funtionality is often better than CWM!
roselanguste said:
There is a other custom ROM for Padfone2 from Sissidroid! Search on XDA for - Guerilla ROM - it is easy to find, and in the thread to this ROM there is a link for Download CWM6.0.4.4. Because CWM6.0.4.4 is needed to Flash Guerilla-ROM from Sissidroid!
In Google search - TWRP for Padfone2 - then you find a TWRP-Site, from there you can Download TWRP-Recoverys for Padfone2. Take the Version 2.6.3.0 of TWRP, not other. The other Versions dont go! TWRP is a Recovery like CWM, but TWRP has a Touch-Interface, and the funtionality is often better than CWM!
Click to expand...
Click to collapse
ok am gonna look for cwm6.0.44 and for twrp 2.6.3.0 and flash one of them on my phone not just like how i was did i mean just boot it and after that flash one of the roms which you told me about them already but just to remind you my phone its not rooted is that fine ... let me know and thank you so much my friend
The Root is here not so important. In most cases a ROM-Flash Unrooting the device! Every Time when i Flash a ROM, the device is after the Flash unrooted, and i must it Root again! Root is important for a Running System! And it gives a way to Root the Device over ADB/Fastboot, but i dont know how. But i have never Need a Root for ROM-Flash!
wasim74 said:
ok am gonna look for cwm6.0.44 and for twrp 2.6.3.0 and flash one of them on my phone not just like how i was did i mean just boot it and after that flash one of the roms which you told me about them already but just to remind you my phone its not rooted is that fine ... let me know and thank you so much my friend
Click to expand...
Click to collapse
sorry my friend : i mean my padfone 2 its not have root its ( unrooted ) so can i flash the custom recovery cwm or twrp on my phone and flash custom roms without having root on my padfone 2 ,,,,,, can i do that without root or i cant ? and thanks
Yes, you can do that without root! Important for that is only you can go in Fastbootmode and CWM/TWRP!
roselanguste said:
Yes, you can do that without root! Important for that is only you can go in Fastbootmode and CWM/TWRP!
Click to expand...
Click to collapse
hi my friend : i have problem with flashing the recovery { fastboot flash recovery recovery.img } i dont know why and i tried to just boot the recovery img for test : fastboot boot boot recovery.img i tried it with twrp and its show me just the picture TEAM WIN BUT ITS NOT FUNCTIONAL CHECK THE PICS PLEASE AND LET ME KNOW WHAT IS THE PROBLEM AND THANKS
On the pics i see, that recovery-flash was failure! In your CMD-pic, adb gives you a writing-failure! That can happen, when you try it ones! Try it again, and also with cwm! What for twrp version have you try? By right flashing, cmd gives you a sending recovery ok, and writing recovery ok! You have sending ok, but writing a failure!?
And what for adb/fastboot binarys use you?
P.s.: I have a important question, as you tryed to flash Asus Firmwares, have you unzip the Firmware before flashing? Or just Download and Flash how it is!

Help, trying to flash via recovery acer a1-830

hello,
Acer iconia a1-830, I'm trying to flash a stock firmware SDs_Acer_AV0K0_A1-830_1.007.00_WW_GEN1.zip
i saw this file for a1-830 acer, it says like this
Firmwares
Flashable via (stock) Recovery
A1-830
SDs_Acer_AV0K0_A1-830_1.007.00_WW_GEN1.zip
SDs Acer_AV0K0_A1-830_RV01RC02_WW_GEN1.zip
SDs_Acer_AV0K0_A1-830_RV01RC05_WW_GEN1.zip
So i downloaded SDs_Acer_AV0K0_A1-830_1.007.00_WW_GEN1.zip,
i assume it's flashable via android system recovery, so copied the file to my microsd card and boot to recovery then only option i know to flash it by "apply update from external storage" then select the file.
it gives me this error installation aborted.. it is trying to find update package.
tried changing file name to update.zip still the same error. i know i'm doing it wrong.
anyone knows how to flash this files to my acer iconia a1-830?
thanks in advance.:laugh:
Then i think the file is corrupted.Try flashing through cwm or twrp recovery
IamAlexD said:
Then i think the file is corrupted.Try flashing through cwm or twrp recovery
Click to expand...
Click to collapse
Thanks for the reply..
BTW, the reason why i'm flashing stock firmware is because i'm stuck in a bootloop... and hard reset not able to fix it..
i'm still researching on cwm or twrp recovery.
darkfilth101 said:
Thanks for the reply..
BTW, the reason why i'm flashing stock firmware is because i'm stuck in a bootloop... and hard reset not able to fix it..
i'm still researching on cwm or twrp recovery.
Click to expand...
Click to collapse
Have you tried TWRP or CWM? If you are searching for TWRP or CWM for acer iconia then http://www.cwm-twrp-recovery.co/2015/08/acer-iconia-a1-830-5930.html
has the both recovery files (the guy rewrite the post from Xda, i cant find the original article to share)and there are few comments on that post.I haven't try because i dont have the device.You may try the guide and replay me if it works thanks.
IamAlexD said:
Have you tried TWRP or CWM? If you are searching for TWRP or CWM for acer iconia then http://www.cwm-twrp-recovery.co/2015/08/acer-iconia-a1-830-5930.html
has the both recovery files (the guy rewrite the post from Xda, i cant find the original article to share)and there are few comments on that post.I haven't try because i dont have the device.You may try the guide and replay me if it works thanks.
Click to expand...
Click to collapse
Thanks for the reply, I already solved it. able to flash it using SDK tools.:good:
darkfilth101 said:
Thanks for the reply, I already solved it. able to flash it using SDK tools.:good:
Click to expand...
Click to collapse
Good to hear.:good:
IamAlexD said:
Have you tried TWRP or CWM? If you are searching for TWRP or CWM for acer iconia then
has the both recovery files (the guy rewrite the post from Xda, i cant find the original article to share)and there are few comments on that post.I haven't try because i dont have the device.You may try the guide and replay me if it works thanks.
Click to expand...
Click to collapse
That site is a joke. I tried to download Lollipop for my a1 830 and the file turned out to be CENTos. It installed fasterweb spyware on my machine after going through the survey process.
I am also stuck in a bootloop. If you know how to solve this please reply. I cant find a working recovery file but I will give you a headsup on what worked when it works
darkfilth101 said:
Thanks for the reply, I already solved it. able to flash it using SDK tools.:good:
Click to expand...
Click to collapse
can you tell me how? Im also stuck in a bootloop and I am just about to flash the update. If it fails I want to know how to solve it. I have sdk manager, what else do I need?
Acer Iconia A1-830
RAZERZDAHACKER said:
can you tell me how? Im also stuck in a bootloop and I am just about to flash the update. If it fails I want to know how to solve it. I have sdk manager, what else do I need?
Acer Iconia A1-830
Click to expand...
Click to collapse
FIXED! I RESTORED TO JELLYBEAN AND IT REMOVED ROOT ACCES AND MADE WARRANTY RESTORED SO TOOK IT DOWN TO SHOP, GOT A NEW ONE AND ROOTED IT USING THIS TOOL. USED ZIPME FOR COMPLETE BACKUP AND I WILL POST A RECOVERY FOR KITKAT USERS
darkfilth101 said:
hello,
Acer iconia a1-830, I'm trying to flash a stock firmware SDs_Acer_AV0K0_A1-830_1.007.00_WW_GEN1.zip
i saw this file for a1-830 acer, it says like this
Firmwares
Flashable via (stock) Recovery
A1-830
SDs_Acer_AV0K0_A1-830_1.007.00_WW_GEN1.zip
SDs Acer_AV0K0_A1-830_RV01RC02_WW_GEN1.zip
SDs_Acer_AV0K0_A1-830_RV01RC05_WW_GEN1.zip
So i downloaded SDs_Acer_AV0K0_A1-830_1.007.00_WW_GEN1.zip,
i assume it's flashable via android system recovery, so copied the file to my microsd card and boot to recovery then only option i know to flash it by "apply update from external storage" then select the file.
it gives me this error installation aborted.. it is trying to find update package.
tried changing file name to update.zip still the same error. i know i'm doing it wrong.
anyone knows how to flash this files to my acer iconia a1-830?
thanks in advance.:laugh:
Click to expand...
Click to collapse
Install driver first just connect phone to pc or use adb installer for driver installation.
Then unplug it if driver installed properly.
Extract/Open SP_Flash_Tool_v3.1252
Click "Scatter-loading"then browse "MT6575_Android_scatter_emmc"inside the Firmware.
Hit Download button.
Hold volume down then connect to PC and wait until flashing is done.
See more at Acer A1-830 Manual- guideusermanual.com/product-name-a1-830-manual&po=568483&lang=English

Categories

Resources